- 03 Dec, 2009 15 commits
-
-
ashish kalra authored
Enable device hot-plug support on Port multiplier fan-out ports Signed-off-by: Ashish Kalra <Ashish.Kalra@freescale.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
Bartlomiej Zolnierkiewicz authored
Alan Cox reported that cable detection sometimes works unreliably for HPT3xxN and that the issue is fixed by adding debounce delay as used by the vendor driver. Sergei Shtylyov also noticed that debounce delay is needed for all HPT37x and HPT3xxN chipsets according to vendor drivers. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
Bartlomiej Zolnierkiewicz authored
The detection was reversed between primary and secondary ports. Fix it to match hpt366 and the vendor driver. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
Matthew Garrett authored
sysfs attributes shouldn't require newlines. Make it possible to set the link power management policy without a trailing newline. Signed-off-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
Otavio Salvador authored
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
Bartlomiej Zolnierkiewicz authored
We can use the same ->pre_reset method for all HPT37x chipsets now. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
Bartlomiej Zolnierkiewicz authored
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
Shaohua Li authored
I obseved there is a sata_async_notification() for every ahci interrupt. But the async notification does nothing (this is hard disk drive and no pmp). This cause cpu wastes some time on sntf register access. It appears ICH AHCI doesn't support SNotification register, but the controller reports it does. After quirking it, the async notification disappears. PS. it appears all ICH don't support SNotification register from ICH manual, don't know if we need quirk all ICH. I don't have machines with all kinds of ICH. Signed-off-by: Shaohua Li <shaohua.li@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
Vivek Mahajan authored
The following patch adds MSI support. Some platforms may have broken MSI, so those are defaulted to use legacy PCI interrupts. Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
Robert Hancock authored
Remove the experimental tag on Parallel ATA drivers. Though some of the individual PATA drivers are still marked as experimental, as a group they can hardly be considered to be, given they've been used in various distros for some time. Signed-off-by: Robert Hancock <hancockrwd@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
Thiago Farina authored
Use ARRAY_SIZE macro of kernel api instead. Signed-off-by: Thiago Farina <tfransosi@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
Jiri Slaby authored
In via_init_one, when via_isa_bridges iterator reaches PCI_DEVICE_ID_VIA_ANON and last but one via_isa_bridges bridge is found but rev doesn't match, pci_dev_put(isa) is called twice. Do pci_dev_put only once. Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
Krzysztof Halasa authored
Tested on IXP425 + CS5536. Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
Tejun Heo authored
Missing _SDD is not an error. Don't treat it as one. Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
-
Linus Torvalds authored
-
- 02 Dec, 2009 25 commits
-
-
Julia Lawall authored
request_region should be used with release_region, not request_mem_region. Geert Uytterhoeven pointed out that in the case of drivers/video/gbefb.c, the problem is actually the other way around; request_mem_region should be used instead of request_region. The semantic patch that finds/fixes this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @r1@ expression start; @@ request_region(start,...) @b1@ expression r1.start; @@ request_mem_region(start,...) @depends on !b1@ expression r1.start; expression E; @@ - release_mem_region + release_region (start,E) // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Atsushi Nemoto authored
TXx9 SPI bit rate is calculated by: fBR = (spi-baseclk) / (n + 1) Fix calculation of min_speed_hz, max_speed_hz and n. Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6Linus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: mfd: Correct WM831X_MAX_ISEL_VALUE
-
Anisse Astier authored
These laptops often leave i8042 in a wierd state resulting in non- operational touchpad and keyboard. Signed-off-by: Anisse Astier <anisse@astier.eu> Signed-off-by: Dmitry Torokhov <dtor@mail.ru> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
git://neil.brown.name/mdLinus Torvalds authored
* 'for-linus' of git://neil.brown.name/md: md: revert incorrect fix for read error handling in raid1.
-
Rusty Russell authored
Jon confirms that recent modprobe will look in /proc/cmdline, so these cmdline options can still be used. See http://bugzilla.kernel.org/show_bug.cgi?id=14164Reported-by: Adam Williamson <awilliam@redhat.com> Cc: stable@kernel.org Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
git://ftp.linux-mips.org/pub/scm/upstream-linusLinus Torvalds authored
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: MIPS: RB532: Fix devices.c compilation. MIPS: Fix MIPS I build.
-
git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdogLinus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog: [PATCH] rc32434_wdt: fix compilation failure [WATCHDOG] rc32434_wdt.c: use resource_size()
-
Helge Deller authored
On the parisc architecture we face for each and every loaded kernel module this kernel "badness warning": sysfs: cannot create duplicate filename '/module/ac97_bus/sections/.text' Badness at fs/sysfs/dir.c:487 Reason for that is, that on parisc all kernel modules do have multiple .text sections due to the usage of the -ffunction-sections compiler flag which is needed to reach all jump targets on this platform. An objdump on such a kernel module gives: Sections: Idx Name Size VMA LMA File off Algn 0 .note.gnu.build-id 00000024 00000000 00000000 00000034 2**2 CONTENTS, ALLOC, LOAD, READONLY, DATA 1 .text 00000000 00000000 00000000 00000058 2**0 CONTENTS, ALLOC, LOAD, READONLY, CODE 2 .text.ac97_bus_match 0000001c 00000000 00000000 00000058 2**2 CONTENTS, ALLOC, LOAD, READONLY, CODE 3 .text 00000000 00000000 00000000 000000d4 2**0 CONTENTS, ALLOC, LOAD, READONLY, CODE ... Since the .text sections are empty (size of 0 bytes) and won't be loaded by the kernel module loader anyway, I don't see a reason why such sections need to be listed under /sys/module/<module_name>/sections/<section_name> either. The attached patch does solve this issue by not exporting section names which are empty. This fixes bugzilla http://bugzilla.kernel.org/show_bug.cgi?id=14703Signed-off-by: Helge Deller <deller@gmx.de> CC: rusty@rustcorp.com.au CC: akpm@linux-foundation.org CC: James.Bottomley@HansenPartnership.com CC: roland@redhat.com CC: dave@hiauly1.hia.nrc.ca Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6Linus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6: regulator: Initialise wm831x structure pointor for ISINK driver
-
Mark Brown authored
The version that made it into mainline missed the initialisation of the chip handle. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
-
Florian Fainelli authored
We should now use dev_set_drvdata to set the driver driver_data field. Signed-off-by: Florian Fainelli <florian@openwrt.org> Patchwork: http://patchwork.linux-mips.org/patch/747/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-
Ralf Baechle authored
Broken by d63c63e889bbeeaa461a8addf1245f89f3ce4ece (lmo) rsp. f1e39a4a (kernel.org). Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Patchwork: http://patchwork.linux-mips.org/patch/746/
-
git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6Linus Torvalds authored
* 'fix' of git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6: [ARM] pxamci: call mmc_remove_host() before freeing resources
-
Daniel Mack authored
mmc_remove_host() will cause the mmc core to switch off the bus power by eventually calling pxamci_set_ios(). This function uses the regulator or the GPIO which have been freed already. This causes the following Oops on module unload. [ 49.519649] Unable to handle kernel paging request at virtual address 30303a70 [ 49.526878] pgd = c7084000 [ 49.529563] [30303a70] *pgd=00000000 [ 49.533136] Internal error: Oops: 5 [#1] [ 49.537025] last sysfs file: /sys/devices/platform/pxa27x-ohci/usb1/1-1/1-1:1.0/host0/target0:0:0/0:0:0:0/scsi_level [ 49.547471] Modules linked in: pxamci(-) eeti_ts [ 49.552061] CPU: 0 Not tainted (2.6.32-rc8 #322) [ 49.557001] PC is at regulator_is_enabled+0x3c/0xbc [ 49.561846] LR is at regulator_is_enabled+0x30/0xbc [ 49.566691] pc : [<c01a2448>] lr : [<c01a243c>] psr: 60000013 [ 49.566702] sp : c7083e70 ip : 30303a30 fp : 00000000 [ 49.578093] r10: c705e200 r9 : c7082000 r8 : c705e2e0 [ 49.583280] r7 : c7061340 r6 : c7061340 r5 : c7083e70 r4 : 00000000 [ 49.589759] r3 : c04dc434 r2 : c04dc434 r1 : c03eecea r0 : 00000047 [ 49.596241] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user [ 49.603329] Control: 0000397f Table: a7084018 DAC: 00000015 [ 49.609031] Process rmmod (pid: 1101, stack limit = 0xc7082278) [ 49.614908] Stack: (0xc7083e70 to 0xc7084000) [ 49.619238] 3e60: c7082000 c703c4f8 c705ea00 c04f4074 [ 49.627366] 3e80: 00000000 c705e3a0 ffffffff c0247ddc c70361a0 00000000 c705e3a0 ffffffff [ 49.635499] 3ea0: c705e200 bf006400 c78c4f00 c705e200 c705e3a0 ffffffff c705e200 ffffffff [ 49.643633] 3ec0: c04d8ac8 c02476d0 ffffffff c0247c60 c705e200 c0248678 c705e200 c0249064 [ 49.651765] 3ee0: ffffffff bf006204 c04d8ad0 c04d8ad0 c04d8ac8 bf007490 00000880 c00440c4 [ 49.659898] 3f00: 0000b748 c01c5708 bf007490 c01c44c8 c04d8ac8 c04d8afc bf007490 c01c4570 [ 49.668031] 3f20: bf007490 bf00750c c04f4258 c01c37a4 00000000 bf00750c c7083f44 c007b014 [ 49.676162] 3f40: 4000d000 6d617870 08006963 00000001 00000000 c7085000 00000001 00000000 [ 49.684287] 3f60: 4000d000 c7083f8c 00000001 bea01a54 00005401 c7ab1400 c00440c4 00082000 [ 49.692420] 3f80: bf00750c 00000880 c7083f8c 00000000 4000cfa8 00000000 00000880 bea01cc8 [ 49.700552] 3fa0: 00000081 c0043f40 00000000 00000880 bea01cc8 00000880 00000006 00000000 [ 49.708677] 3fc0: 00000000 00000880 bea01cc8 00000081 00000097 0000cca4 0000b748 00000000 [ 49.716802] 3fe0: 4001a4f0 bea01cc0 00018bf4 4001a4fc 20000010 bea01cc8 a063e021 a063e421 [ 49.724958] [<c01a2448>] (regulator_is_enabled+0x3c/0xbc) from [<c0247ddc>] (mmc_regulator_set_ocr+0x14/0xd8) [ 49.734836] [<c0247ddc>] (mmc_regulator_set_ocr+0x14/0xd8) from [<bf006400>] (pxamci_set_ios+0xd8/0x17c [pxamci]) [ 49.745044] [<bf006400>] (pxamci_set_ios+0xd8/0x17c [pxamci]) from [<c02476d0>] (mmc_power_off+0x50/0x58) [ 49.754555] [<c02476d0>] (mmc_power_off+0x50/0x58) from [<c0247c60>] (mmc_detach_bus+0x68/0xc4) [ 49.763207] [<c0247c60>] (mmc_detach_bus+0x68/0xc4) from [<c0248678>] (mmc_stop_host+0xd4/0x1bc) [ 49.771944] [<c0248678>] (mmc_stop_host+0xd4/0x1bc) from [<c0249064>] (mmc_remove_host+0xc/0x20) [ 49.780681] [<c0249064>] (mmc_remove_host+0xc/0x20) from [<bf006204>] (pxamci_remove+0xc8/0x174 [pxamci]) [ 49.790211] [<bf006204>] (pxamci_remove+0xc8/0x174 [pxamci]) from [<c01c5708>] (platform_drv_remove+0x1c/0x24) [ 49.800164] [<c01c5708>] (platform_drv_remove+0x1c/0x24) from [<c01c44c8>] (__device_release_driver+0x7c/0xc4) [ 49.810110] [<c01c44c8>] (__device_release_driver+0x7c/0xc4) from [<c01c4570>] (driver_detach+0x60/0x8c) [ 49.819535] [<c01c4570>] (driver_detach+0x60/0x8c) from [<c01c37a4>] (bus_remove_driver+0x90/0xcc) [ 49.828452] [<c01c37a4>] (bus_remove_driver+0x90/0xcc) from [<c007b014>] (sys_delete_module+0x1d8/0x254) [ 49.837891] [<c007b014>] (sys_delete_module+0x1d8/0x254) from [<c0043f40>] (ret_fast_syscall+0x0/0x28) [ 49.847145] Code: eb06c53a e596c030 e1a0500d e59f106c (e59c0040) [ 49.853566] ---[ end trace b5fa66a00cea142f ]--- Signed-off-by: Daniel Mack <daniel@caiaq.de> Reported-by: Sven Neumann <s.neumann@raumfeld.com> Cc: Pierre Ossman <pierre@ossman.eu> Cc: linux-mmc@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Cc: stable@kernel.org Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
-
Florian Fainelli authored
This patch fixes the compilation failure of rc32434 due to a bad module parameter description. Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
-
H Hartley Sweeten authored
The size value passed to ioremap_nocache() is not correct. Use resource_size() to get the correct value. Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Cc: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
-
Randy Dunlap authored
The SYSFS_DEPRECATED_V2 says "remove" older, deprecated features, but it actually enables them, so correct this confusing, backwards text. Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: Kay Sievers <kay.sievers@vrfy.org> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Johannes Weiner authored
When detecting power failure, the probe function would reset the clock time to defined state. However, the clock's _date_ might still be bogus and a subsequent probe fails when sanity-checking these values. Change the power-failure fixup code to do a full setting of rtc_time, including a valid date. Signed-off-by: Johannes Weiner <jw@emlix.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Paul Gortmaker <p_gortmaker@yahoo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Johannes Weiner authored
The possible CCR_Y2K register values are 19 or 20 and struct rtc_time's tm_year is in years since 1900. The function translating rtc_time to register values assumes tm_year to be years since first christmas, though, and we end up storing 0 or 1 in the CCR_Y2K register, which the hardware does not refuse to do. A subsequent probing of the clock fails due to the invalid value range in the register, though. [ And if it didn't, reading the clock would yield a bogus year because the function translating registers to tm_year is assuming a register value of 19 or 20. ] This fixes the conversion from years since 1900 in tm_year to the corresponding CCR_Y2K value of 19 or 20. Signed-off-by: Johannes Weiner <jw@emlix.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Paul Gortmaker <p_gortmaker@yahoo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Peter Horton authored
Prevent the AoE block driver from creating cache aliases of page cache pages on machines with virtually indexed caches. Building kernels on an AT91SAM9G20 board without this patch fails with segmentation faults after a couple of passes. Signed-off-by: Peter Horton <zero@colonel-panic.org> Cc: "Ed L. Cashin" <ecashin@coraid.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Alek Du authored
- Remove wrong and unnecessary unmask operation - Remove extra GEDR reading This fixes the loss of interrupts which occurs when two or more pins are triggered in close succession. Signed-off-by: Alek Du <alek.du@intel.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Sam Ravnborg authored
It has been fun but the last year or more it has been a duty and a burden. So I leave it open for others to take over. Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Cc: Anibal Monsalve Salazar <anibal@debian.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Michal Marek <mmarek@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Sudhakar Rajashekhara authored
Following issues have been addressed on DA8XX/OMAP-L1XX: a. Screen misalignment during booting when frame buffer console is enabled. b. Driver was configured always in PSEUDOCOLOR mode. This patch dynamically configures the driver either in PSEUDOCOLOUR or TRUECOLOR mode depending on bpp. c. The RED and BLUE offsets were interchanged resulting in wrong bootup logo colour. This patch has been tested on DA830/OMAP-L137 and DA850/OMAP-L138 EVMs. Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Cc: Steve Chen <schen@mvista.com> Cc: Pavel Kiryukhin <pkiryukhin@ru.mvista.com> Cc: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Dan Carpenter authored
"rtc" is freed and then dereferenced on the next line. This patch fixes that. Signed-off-by: Dan Carpenter <error27@gmail.com> Acked-by: Alessandro Zummo <a.zummo@towertech.it> Cc: David Brownell <david-b@pacbell.net> Cc: Paul Gortmaker <p_gortmaker@yahoo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-