Now two modules are built, ath6kl_sdio.ko and ath6kl_usb.ko. But the USB
module isn't fully functional yet as HTC layer is missing support and
that's why it's marked as experimental for now.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

As HTC layer doesn't support USB devices return an error if that happens.
USB support will be added to HTC in the future, this is just a temporary
solution.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Add USB support for ar6004. Currently only firmware can be booted,
no commands can be sent to firmware yet as HTC layer doesn't work
with USB yet.

Based on patches by Kevin Fang.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

In some rare cases core code needs to know what hif type is used. Add
a field to struct ath6kl to denote that. Hopefully this is just a
temporary solution.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Add support for AR6004 SDIO. Tested scan, association (open mode) and
ping.

kvalo: change commit log a bit, drop board address changes
Signed-off-by: Naveen Gangadharan <ngangadh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

These have changed a bit since last time ar6004 code was commited.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Add also hw 1.1.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This is preparation for USB support which will have different diag
commands.

Based on code by Kevin Fang.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

SDIO and USB have different maximum sizes for BMI commands so make that
configurable.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

In preparation for USB support which has it's own method for bmi.

Based on code by Kevin Fang.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The firmware expects the minimum length of
WMI_SEND_PROBE_RESPONSE_CMDID to be 13. However, when the device is a
P2P GO and it needs to send a probe response to a non-P2P client,
there are no P2P IEs to be added, and therefore the length of the WMI
command is 12. This command gets rejected by the firmware. To fix
this, add an extra byte to satisfy the minimum length requirement.
Signed-off-by: Aarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

When the connect event is received from the target in IBSS mode,
cfg80211_ibss_joined() is called without informing BSS info to
cfg80211 layer which internally hits the below WARN_ON message.

WARNING: at net/wireless/ibss.c:33 __cfg80211_ibss_joined+0x153/0x180 [cfg80211]()
[..]
[ 4916.845878] Call Trace:
[ 4916.845889]  [<c10427d2>] warn_slowpath_common+0x72/0xa0
[ 4916.845905]  [<f8bccc63>] ? __cfg80211_ibss_joined+0x153/0x180 [cfg80211]
[ 4916.845918]  [<f8bccc63>] ? __cfg80211_ibss_joined+0x153/0x180 [cfg80211]
[ 4916.845923]  [<c1042822>] warn_slowpath_null+0x22/0x30
[ 4916.845934]  [<f8bccc63>] __cfg80211_ibss_joined+0x153/0x180 [cfg80211]
[ 4916.845941]  [<c1025108>] ? default_spin_lock_flags+0x8/0x10
[ 4916.845952]  [<f8bb7fcd>] cfg80211_process_rdev_events+0x19d/0x220 [cfg80211]
[ 4916.845962]  [<f8bb669b>] cfg80211_event_work+0x2b/0x50 [cfg80211]
[ 4916.845968]  [<c105aae6>] process_one_work+0x116/0x3c0
[ 4916.845977]  [<f8bb6670>] ? cfg80211_get_dev_from_info+0x40/0x40 [cfg80211]
[ 4916.845982]  [<c105cdf0>] worker_thread+0x140/0x3b0
[ 4916.845986]  [<c105ccb0>] ? manage_workers+0x1f0/0x1f0
[ 4916.845991]  [<c1060c64>] kthread+0x74/0x80
[ 4916.845995]  [<c1060bf0>] ? kthread_worker_fn+0x160/0x160
[ 4916.846001]  [<c14e7bbe>] kernel_thread_helper+0x6/0x10
[ 4916.846005] ---[ end trace 769254924e409367 ]---

This patch make sures that BSS info is delivered via cfg80211_inform_bss()
to cfg80211 in advance before intimating IBSS status to cfg80211.

In addition to this, one debug message is also added to know
ad-hoc mode status (creator/joiner).

kvalo: change subject
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

"ath6kl: Maintain virtual interface in a list" mistakenly stops the
netq only when the mode is ibss. This causes packet drops in sta mode
when the available cookies (buffer abstraction in ath6kl and also used
for tx throttling) runs out for the highest priority traffic. This patch
just fixes this regression though the original code may still need fixes
which can be addressed in separate patches.
Reported-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

When buffer alignmnet is applied, the data pointer of skb taken from
cookie will no longer point to the first byte of the actual data.
But the skb->data pointer is used in ath6kl_tx_complete() to get
the index of the virtual interface which will not give the correct
interface index and sometimes may give the following WARN_ON() message.
Use packet->buf instead of skb->data to fix this.

WARNING: at drivers/net/wireless/ath/ath6kl/wmi.c:88 ath6kl_get_vif_by_index+0x5b/0x60 [ath6kl]()
Hardware name: 2842K3U
Modules linked in: ath6kl mmc_block cfg80211 binfmt_misc ppdev nfs nfsd lockd nfs_acl auth_rpcgss sunrpc exportfs snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_intel
+snd_hda_codec snd_hwdep snd_pcm_oss snd_mixer_oss snd_pcm snd_seq_dummy thinkpad_acpi snd_seq_oss snd_seq_midi snd_rawmidi joydev fbcon tileblit font bitblit softcursor
+snd_seq_midi_event snd_seq snd_timer snd_seq_device i915 uvcvideo drm_kms_helper drm psmouse serio_raw snd i2c_algo_bit sdhci_pci videodev intel_agp soundcore intel_gtt jmb38x_ms
+memstick sdhci snd_page_alloc nvram lp parport agpgart video ahci r8169 mii libahci [last unloaded: ath6kl]
Pid: 15482, comm: kworker/u:1 Tainted: G        W   3.1.0-rc10-wl+ #2
Call Trace:
 [<c0144d72>] warn_slowpath_common+0x72/0xa0
 [<fb7c94fb>] ? ath6kl_get_vif_by_index+0x5b/0x60 [ath6kl]
 [<fb7c94fb>] ? ath6kl_get_vif_by_index+0x5b/0x60 [ath6kl]
 [<c0144dc2>] warn_slowpath_null+0x22/0x30
 [<fb7c94fb>] ath6kl_get_vif_by_index+0x5b/0x60 [ath6kl]
 [<fb7c7028>] ath6kl_tx_complete+0x128/0x4d0 [ath6kl]
 [<c04df920>] ? mmc_request_done+0x80/0x80
 [<fb7b9e2e>] htc_tx_complete+0x5e/0x70 [ath6kl]
 [<c05e4cf6>] ? _raw_spin_unlock_bh+0x16/0x20
 [<fb7ce588>] ? ath6kl_sdio_scatter_req_add+0x48/0x60 [ath6kl]
 [<fb7b9f42>] htc_async_tx_scat_complete+0xb2/0x120 [ath6kl]
 [<fb7ce9e7>] ath6kl_sdio_scat_rw+0x87/0x370 [ath6kl]
 [<c0101e12>] ? __switch_to+0xd2/0x190
 [<c01397b5>] ? finish_task_switch+0x45/0xd0
 [<c05e272e>] ? __schedule+0x3ae/0x8b0
 [<fb7cf00a>] ath6kl_sdio_write_async_work+0x4a/0xf0 [ath6kl]
 [<c015d266>] process_one_work+0x116/0x3c0
 [<fb7cefc0>] ? ath6kl_sdio_read_write_sync+0xb0/0xb0 [ath6kl]
 [<c015f5b0>] worker_thread+0x140/0x3b0
 [<c015f470>] ? manage_workers+0x1f0/0x1f0
 [<c0163424>] kthread+0x74/0x80
 [<c01633b0>] ? kthread_worker_fn+0x160/0x160
 [<c05ebdc6>] kernel_thread_helper+0x6/0x10
Reported-by: Aarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This is needed to know whether the STA requests WAPI to be used and if
so, with what AKM and cipher.
Signed-off-by: Dai Shuibing <shuibing@qca.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: Dai Shuibing <shuibing@qca.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Indicate support for WPI-SMS4 cipher and allow SMS4 keys to be
configured.
Signed-off-by: Dai Shuibing <shuibing@qca.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

100 bytes are allocated to store the parameters which are needed
to create a priority stream. These 100 bytes are not sufficiant and
throws error when running the following command.

echo "6 2 3 1 1 9999999 9999999 9999999 7777777 0 6 45000 200 56789000
 56789000 5678900 0 0 9999999 20000 0" > create_qos

179 bytes are needed when the following vlaues are given so that
a maximum possible value in that data type can be given in decimal.

echo "255 255 255 255 255 4294967295 4294967295 4294967295 4294967295
 4294967295 255 65535 65535 4294967295 4294967295 4294967295 4294967295
 4294967295 4294967295 4294967295 4294967295" > create_qos

Following takes 187 bytes when given in hex

echo "0xff 0xff 0xff 0xff 0xff 0xffffffff 0xffffffff 0xffffffff 0xffffffff 0xffffffff
 0xff 0xffff 0xffff 0xffffffff 0xffffffff 0xffffffff 0xffffffff 0xffffffff 0xffffffff
 0xffffffff 0xffffffff" > create_qos

Increase the size to 200 bytes so that it can hold upto the maximum
value possible for that data type.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

skb is dropped in ath6kl_data_tx() when the headroom in skb
is insufficient. We hit this condition for every skb in AP mode
which is used with bridge, so all tx packets are getting dropped
when tried to send traffic to wireless client from bridge. Fix
this by reallocating the headroom instead of dropping the skb
when it has lesser headroom than needed.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

* Removed unused WOW_MAX_FILTER_LISTS macro.

* Removed empty ath6kl_wmi_get_wow_list_event_rx() function.
  List of configured WOW patterns are maintained in CFG layer
  itself. No need to have this function in ath6kl to get
  configured WOW pattern list. It can added later if we need
  it for debugging.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Set the list of ath6kl's WOW trigger options in wiphy->wowlan.flags
variable during wiphy registration. So that, those options can be
configured via iw.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

In the current code, WOW resume is executed first from RX path
and ar->state is moved to ATH6KL_STATE_ON. When platform calls
ath6kl_sdio_resume() in CFG resume context, that time ar->state
could have moved to ON state. Printing WARN_ON(1) is void in
this context. Hence removing this.

Once WOW resume is removed from RX path, This WARN_ON msg can be
reverted.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The target triggers sdio data line to wake up the host when
WOW pattern matches. This causes sdio irq handler is being
executed in the host side which internally hits ath6kl's RX path.

WOW resume should happen before start processing any data from
the target. So it's required to perform WOW resume in RX path.

This area needs bit rework to avoid WOW resume in RX path,
As of now it's fine to have this model, rework will be done later.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Link ath6kl's wow suspend/resume functions with the actual suspend/resume path.

WOW mode is selected when the host sdio controller supports both
MMC_PM_KEEP_POWER and MMC_PM_WAKE_SDIO_IRQ capabilities.

kvalo: also adds a missing break in ath6kl_cfg80211_resume(), luckily
it didn't have any effect on functionality.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

ath6kl_cfg80211_stop() call is not applicable for WOW mode. Hence moving
this call to deep sleep and cut pwr specific cases.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

In addition to existing deep sleep and cut pwr mode, new state
is added in ath6kl_cfg_suspend_mode as well as in ath6kl_state for WOW.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

cfg80211 layer provides user defined wow parameters like Filter options, Patterns,
Pattern's mask, etc via "struct cfg80211_wowlan *wow" to suspend function.

Right now, this wowlan parameter is not handled in __ath6kl_cfg80211_suspend func.
This parameter has to be passed to HIF layer, So that it can be passed back to
ath6kl's cfg interface layer when WOW mode is selected.

In case of deep sleep and cut power mode, it's not handled.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This is the core WOW suspend/resume functions will be called
in PM suspend/resume path.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

It will be used in WOW suspend/resume functions to
active/deactivate WOW suspend mode.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

These commands will be used in WOW suspend/resume functions
to configure WOW parameters like patterns to be matched
and it's mask value, etc.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Instead of converting any error to EIO, just return the real error
value to upper layers.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

There is no guarantee on the caller using 8-octet buffer for
key->seq, so better follow the key->seq_len parameter on figuring
out how many octets to copy.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This is to force ath6kl to power off hardware during suspend even if
sdio support keep power. This is needed, for example, when sdio
controller is buggy or maximum powersaving is desired.

Usage:

insmod ath6kl.ko suspend_cutpower=1
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Jouni reported that my patch "ath6kl: power down hardware when interface
is down" caused a regression on his x86 boxes and scan didn't work anymore.
I was able to reproduce the problem by disabling all debug messages.

So there has to be a race condition somewhere in the code and disable the
functionality until the race is fixed. Now hardware is powered from the
point where module is loaded until it's removed.
Reported-by: Jouni Malinen <jouni@qca.qualcomm.com>
Tested-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

The following is the lockdep warning which detects possible
deadlock condition with the way ar->lock and ar->list_lock
are being used.

  (&(&ar->lock)->rlock){+.-...}, at: [<ffffffffa0492d13>] ath6kl_indicate_tx_activity+0x83/0x110 [ath6kl]
 but this lock took another, SOFTIRQ-unsafe lock in the past:
  (&(&ar->list_lock)->rlock){+.+...}

 and interrupts could create inverse lock ordering between them.

 other info that might help us debug this:
  Possible interrupt unsafe locking scenario:

        CPU0                    CPU1
        ----                    ----
   lock(&(&ar->list_lock)->rlock);
                                local_irq_disable();
                                lock(&(&ar->lock)->rlock);
                                lock(&(&ar->list_lock)->rlock);
   <Interrupt>
     lock(&(&ar->lock)->rlock);

  *** DEADLOCK ***

softirqs have to be disabled when acquiring ar->list_lock to avoid
the above deadlock condition. When the above warning printed the
interface is still up and running without issue.
Reported-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

If sdio controller doesn't support keep power, cut power from hardware
during suspend and restart firmware during resume. If we are connected
during suspend, send a disconnected event to user space.

Earlier suspend failed with an error if sdio didn't support keep power.
Now suspend will happen succesfully even with that case.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

These commands are also needed after cutpower suspend so create
a function for them. Also fix memory leaks in ath6kl_sdio_probe() error
path.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This way it's easier to track state changes and in the future add
more warnings about using hardware in wrong states. Currently there
are few random flags for trying to do the same, those will be cleaned
and removed in the future.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

This is in preparation for cutpower suspend feature. HIF layer makes
the decision based on information provided by cfg80211 and what hardware
actually supports. Then it calls ath6kl_cfg80211_suspend() to enable
the chosen mode.

Functionality should be the same, this is just preparation for
more suspend modes (cutpower and wow).
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>