Update the TLB asm to make proper use of _PAGE_DIRY and _PAGE_ACCESSED.
Get rid of _PAGE_HWWRITE too.
Pros:
 - I/D TLB Miss never needs to write to the linux pte.
 - _PAGE_ACCESSED is only set on TLB Error fixing accounting
 - _PAGE_DIRTY is mapped to 0x100, the changed bit, and is set directly
    when a page has been made dirty.
 - Proper RO/RW mapping of user space.
 - Free up 2 SW TLB bits in the linux pte(add back _PAGE_WRITETHRU ?)
 - kernel RO/user NA support.
Cons:
 - A few more instructions in the TLB Miss routines.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

8xx sometimes need to load a invalid/non-present TLBs in
it DTLB asm handler.

These must be invalidated separaly as linux mm don't.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Currently the cpu-allocation/deallocation process comprises of two steps:
- Set the indicators and to update the device tree with DLPAR node
  information.

- Online/offline the allocated/deallocated CPU.

This is achieved by writing to the sysfs tunables "probe" during allocation
and "release" during deallocation.

At the sametime, the userspace can independently online/offline the CPUs of
the system using the sysfs tunable "online".

It is quite possible that when a userspace tool offlines a CPU
for the purpose of deallocation and is in the process of updating the device
tree, some other userspace tool could bring the CPU back online by writing to
the "online" sysfs tunable thereby causing the deallocate process to fail.

The solution to this is to serialize writes to the "probe/release" sysfs
tunable with the writes to the "online" sysfs tunable.

This patch employs a mutex to provide this serialization, which is a no-op on
all architectures except PPC_PSERIES
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Acked-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Currently the cpu-allocation/deallocation on pSeries is a
two step process from the Userspace.

- Set the indicators and update the device tree by writing to the sysfs
  tunable "probe" during allocation and "release" during deallocation.
- Online / Offline the CPUs of the allocated/would_be_deallocated node by
  writing to the sysfs tunable "online".

This patch adds kernel code to online/offline the CPUs soon_after/just_before
they have been allocated/would_be_deallocated. This way, the userspace tool
that performs DLPAR operations would only have to deal with one set of sysfs
tunables namely "probe" and release".
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Acked-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Remove the CPU from the online map to prevent smp_call_function
from sending messages to a stopped CPU.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This patch adds the specific routines to probe and release (add and remove)
cpu resource for the powerpc pseries platform and registers these handlers
with the ppc_md callout structure.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Version 3 of this patch is updated with documentation added to
Documentation/ABI.  There are no changes to any of the C code from v2
of the patch.

In order to support kernel DLPAR of CPU resources we need to provide an
interface to add (probe) and remove (release) the resource from the system.
This patch Creates new generic probe and release sysfs files to facilitate
cpu probe/release.  The probe/release interface provides for allowing each
arch to supply their own routines for implementing the backend of adding
and removing cpus to/from the system.

This also creates the powerpc specific stubs to handle the arch callouts
from writes to the sysfs files.

The creation and use of these files is regulated by the
CONFIG_ARCH_CPU_PROBE_RELEASE option so that only architectures that need the
capability will have the files created.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The Dynamic Logical Partitioning capabilities of the powerpc pseries platform
allows for the addition and removal of resources (i.e. CPU's, memory, and PCI
devices) from a partition. The removal of a resource involves
removing the resource's node from the device tree and then returning the
resource to firmware via the rtas set-indicator call.  To add a resource, it
is first obtained from firmware via the rtas set-indicator call and then a
new device tree node is created using the ibm,configure-coinnector rtas call
and added to the device tree.

This patch provides the kernel DLPAR infrastructure in a new filed named
dlpar.c.  The functionality provided is for acquiring and releasing a resource
from firmware and the parsing of information returned from the
ibm,configure-connector rtas call.  Additionally this exports the pSeries
reconfiguration notifier chain so that it can be invoked when device tree
updates are made.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

In commit 0512a9a8, we unilaterally zero the
"pwm invert" bit in the fan behavior configuration register.  On my PowerBook
G4, this results in the fans going to full speed at low temperature and
shutting off at high temperature because the pwm invert bit is supposed to be
set.

Therefore, record the pwm invert bit at driver load time, and write the bit
into the fan behavior control register.  This restores correct behavior on my
PBG4 and should work around the bit being set to the wrong value after
suspend/resume (which is what the original patch was trying to fix).  It also
fixes a minor omission where the pwm invert bit correction is NOT performed
when switching into automatic mode.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
CC: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Also short-circuit empty updates.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This allows offb to be used for initial framebuffer,
and a kms driver to take over later in the boot sequence.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This is a libata driver for the "macio" IDE controller used on most Apple
PowerMac and PowerBooks. It's a libata equivalent of drivers/ide/ppc/pmac.c

It supports all the features of its predecessor, including mediabay hotplug
and suspend/resume. It should also support module load/unload.

The timing calculations have been simplified to use pre-calculated tables
compared to drivers/ide/pmac.c and it uses the new mediabay interface
provided by a previous patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Tejun Heo <tj@kernel.org>

In libata-sff, ata_sff_post_internal_cmd() directly calls ata_bmdma_stop()
instead of ap->ops->bmdma_stop(). This can be a problem for controllers
that use their own bmdma_stop for which the generic sff one isn't suitable
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>

The hotplug mediabay has tendrils deep into drivers/ide code
which makes a libata port reather difficult. In addition it's
ugly and could be done better.

This reworks the interface between the mediabay and the rest
of the world so that:

   - Any macio_driver can now have a mediabay_event callback
which will be called when that driver sits on a mediabay and
it's been either plugged or unplugged. The device type is
passed as an argument. We can now move all the IDE cruft
into the IDE driver itself

   - A check_media_bay() function can be used to take a peek
at the type of device currently in the bay if any, a cleaner
variant of the previous function with the same name.

   - A pair of lock/unlock functions are exposed to allow the
IDE driver to block the hotplug callbacks during the initial
setup and probing of the bay in order to avoid nasty race
conditions.

   - The mediabay code no longer needs to spin on the status
register of the IDE interface when it detects an IDE device,
this is done just fine by the IDE code itself

Overall, less code, simpler, and allows for another driver
than our old drivers/ide based one.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Remove the old WDT implementation.
Signed-off-by: Albrecht Dreß <albrecht.dress@arcor.de>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

This adds dma_parms to macio devices and initializes them with
default values. This will allow pata_macio to setup the appropriate
max segment size for the block layer.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This adds some basic devres support. When enabled via macio_enable_devres()
resources requested by drivers will be automatically released.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Currently userspace has no chance to find out which virtual address space we're
in and resolve addresses. While that is a big problem for migration, it's also
unpleasent when debugging, as gdb and the monitor don't work on virtual
addresses.

This patch exports enough of the MMU segment state to userspace to make
debugging work and thus also includes the groundwork for migration.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The virtio console, which uses hvc, will get the ability to hot-unplug
ports. Export hvc_remove so that virtio_console can disassociate with
hvc.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Cc: linuxppc-dev@ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Windfarm SMU control is explicitly missing support for a second CPU pump in G5 PowerMacs. Such machines actually exist  (specifically Quads with a second pump), so this patch adds detection for it.

Signed-off by: Bolko Maass <bmaass@math.uni-bremen.de>
CC: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Commit a0668cdc cleans up the handling
of kmem_caches for allocating various levels of pagetables.
Unfortunately, it conflicts badly with CONFIG_PPC_SUBPAGE_PROT, due to
the latter's cleverly hidden technique of adding some extra allocation
space to the top level page directory to store the extra information
it needs.

Since that extra allocation really doesn't fit into the cleaned up
page directory allocating scheme, this patch alters
CONFIG_PPC_SUBPAGE_PROT to instead allocate its struct
subpage_prot_table as part of the mm_context_t.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The stanza for PCI was copied from Bamboo which has four PCI slots.  Yosemite
only has one PCI slot which is mapped to IDSEL 12, ADDR 22, IRQ2 Vector 25,
INTA.
Signed-off-by: Curtis Wald <cwald@watchguardvideo.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

Set PCI-E node inbound DMA ranges size to 4GB for correct boot up of Katmai.
Signed-off-by: Pravin Bathija <pbathija@amcc.com>
Acked-by: Feng Kan <fkan@amcc.com>
Acked-by: Prodyut Hazarika <phazarika@amcc.com>
Acked-by: Loc Ho <lho@amcc.com>
Acked-by: Tirumala Reddy Marri <tmarri@amcc.com>
Acked-by: Victor Gallardo <vgallardo@amcc.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

This reverts commit c045256d.

It breaks build when CONFIG_PPC_SUBPAGE_PROT is not set. I will
commit a fixed version separately
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Many boards have a bug-free ns16550 compatible serial port, which we should
register as PORT_16550A. This introduces a new value "ns16550a" for the
compatible property of of_serial to let a firmware choose that model instead
of using the crippled PORT_16550 mode.
Reported-by: Alon Ziv <alonz@nolaviz.org>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Commit a4fe3ce7 introduced a new
get_user_pages() path for hugepages on powerpc.  Unfortunately, there
is a bug in it's loop logic, which can cause it to overrun the end of
the intended region.  This came about by copying the logic from the
normal page path, which assumes the address and end parameters have
been pagesize aligned at the top-level.  Since they're not *hugepage*
size aligned, the simplistic logic could step over the end of the gup
region without triggering the loop end condition.

This patch fixes the bug by using the technique that the normal page
path uses in levels above the lowest to truncate the ending address to
something we know we'll match with.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Commit a0668cdc cleans up the handling
of kmem_caches for allocating various levels of pagetables.
Unfortunately, it conflicts badly with CONFIG_PPC_SUBPAGE_PROT, due to
the latter's cleverly hidden technique of adding some extra allocation
space to the top level page directory to store the extra information
it needs.

Since that extra allocation really doesn't fit into the cleaned up
page directory allocating scheme, this patch alters
CONFIG_PPC_SUBPAGE_PROT to instead allocate its struct
subpage_prot_table as part of the mm_context_t.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Commit 87ec0e98 in kumar's next branch
broke one of my test configs since it looks like Anton forgot about
that mpc832x_rdb platform which still uses the old style probing for
the SPI stuff.

I'll let them do a cleaner fix that probably involves changing the
probing method and getting rid of the platform device but for now
this will do to fix it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This patch was submitted, discussed, and eventually Acked by everyone, yet
still isn't in the tree.  See:

http://patchwork.ozlabs.org/patch/1240/Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Cc: Arnd Bergmann <arnd@anrdb.de>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Code was added to mm/higmem.c that depends on several
kmap types that powerpc does not support.  We add dummy
invalid definitions for KM_NMI, KM_NM_PTE, and KM_IRQ_PTE.

According to list discussion, this fix should not be needed
anymore starting with 2.6.33.  The code is commented to this
effect so hopefully we will remember to remove this.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

We can kill unused swiotlb variable.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Since they are static inline functions.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The code under "if (is_global_init())" is bogus, and is_global_init()
itself is not right in mt case.

Contrary to what the comment says, nowadays force_sig_info() does kill
init even if the handler is SIG_DFL. Note that force_sig_info() clears
SIGNAL_UNKILLABLE exactly for this case.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

When a CPU is offlined on POWER currently, we call rtas_stop_self() and hand
the CPU back to the resource pool. This path is used for DLPAR which will
cause a change in the LPAR configuration which will be visible outside.

This patch changes the default state a CPU is put into when it is offlined.
On platforms which support ceding the processor to the hypervisor with
latency hint specifier value, during a cpu offline operation,
instead of calling rtas_stop_self(), we cede the vCPU to the hypervisor
while passing a latency hint specifier value. The Hypervisor can use this hint
to provide better energy savings. Also, during the offline
operation, the control of the vCPU remains with the LPAR as oppposed to
returning it to the resource pool.

The patch achieves this by creating an infrastructure to set the
preferred_offline_state() which can be either
- CPU_STATE_OFFLINE: which is the current behaviour of calling
  rtas_stop_self()

- CPU_STATE_INACTIVE: which cedes the vCPU to the hypervisor with the latency
  hint specifier.

The codepath which wants to perform a DLPAR operation can set the
preferred_offline_state() of a CPU to CPU_STATE_OFFLINE before invoking
cpu_down().

The patch also provides a boot-time command line argument to disable/enable
CPU_STATE_INACTIVE.
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This patch provides an extended_cede_processor() helper function
which takes the cede latency hint as an argument. This hint is to be passed
on to the hypervisor to cede to the corresponding state on platforms
which support it.
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Arun R Bharadwaj <arun@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>