When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time.  Fix this up to be much
simpler logic and only create the root debugfs directory once when the
driver is first accessed.  That resolves the memory leak and makes
things more obvious as to what the intent is.

Cc: Marcin Wojtas <mw@semihalf.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: netdev@vger.kernel.org
Cc: stable <stable@kernel.org>
Fixes: 21da57a2 ("net: mvpp2: add a debugfs interface for the Header Parser")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The SRv6 layer allows defining HMAC data that can later be used to sign IPv6
Segment Routing Headers. This configuration is realised via netlink through
four attributes: SEG6_ATTR_HMACKEYID, SEG6_ATTR_SECRET, SEG6_ATTR_SECRETLEN and
SEG6_ATTR_ALGID. Because the SECRETLEN attribute is decoupled from the actual
length of the SECRET attribute, it is possible to provide invalid combinations
(e.g., secret = "", secretlen = 64). This case is not checked in the code and
with an appropriately crafted netlink message, an out-of-bounds read of up
to 64 bytes (max secret length) can occur past the skb end pointer and into
skb_shared_info:

Breakpoint 1, seg6_genl_sethmac (skb=<optimized out>, info=<optimized out>) at net/ipv6/seg6.c:208
208		memcpy(hinfo->secret, secret, slen);
(gdb) bt
 #0  seg6_genl_sethmac (skb=<optimized out>, info=<optimized out>) at net/ipv6/seg6.c:208
 #1  0xffffffff81e012e9 in genl_family_rcv_msg_doit (skb=skb@entry=0xffff88800b1f9f00, nlh=nlh@entry=0xffff88800b1b7600,
    extack=extack@entry=0xffffc90000ba7af0, ops=ops@entry=0xffffc90000ba7a80, hdrlen=4, net=0xffffffff84237580 <init_net>, family=<optimized out>,
    family=<optimized out>) at net/netlink/genetlink.c:731
 #2  0xffffffff81e01435 in genl_family_rcv_msg (extack=0xffffc90000ba7af0, nlh=0xffff88800b1b7600, skb=0xffff88800b1f9f00,
    family=0xffffffff82fef6c0 <seg6_genl_family>) at net/netlink/genetlink.c:775
 #3  genl_rcv_msg (skb=0xffff88800b1f9f00, nlh=0xffff88800b1b7600, extack=0xffffc90000ba7af0) at net/netlink/genetlink.c:792
 #4  0xffffffff81dfffc3 in netlink_rcv_skb (skb=skb@entry=0xffff88800b1f9f00, cb=cb@entry=0xffffffff81e01350 <genl_rcv_msg>)
    at net/netlink/af_netlink.c:2501
 #5  0xffffffff81e00919 in genl_rcv (skb=0xffff88800b1f9f00) at net/netlink/genetlink.c:803
 #6  0xffffffff81dff6ae in netlink_unicast_kernel (ssk=0xffff888010eec800, skb=0xffff88800b1f9f00, sk=0xffff888004aed000)
    at net/netlink/af_netlink.c:1319
 #7  netlink_unicast (ssk=ssk@entry=0xffff888010eec800, skb=skb@entry=0xffff88800b1f9f00, portid=portid@entry=0, nonblock=<optimized out>)
    at net/netlink/af_netlink.c:1345
 #8  0xffffffff81dff9a4 in netlink_sendmsg (sock=<optimized out>, msg=0xffffc90000ba7e48, len=<optimized out>) at net/netlink/af_netlink.c:1921
...
(gdb) p/x ((struct sk_buff *)0xffff88800b1f9f00)->head + ((struct sk_buff *)0xffff88800b1f9f00)->end
$1 = 0xffff88800b1b76c0
(gdb) p/x secret
$2 = 0xffff88800b1b76c0
(gdb) p slen
$3 = 64 '@'

The OOB data can then be read back from userspace by dumping HMAC state. This
commit fixes this by ensuring SECRETLEN cannot exceed the actual length of
SECRET.
Reported-by: Lucas Leong <wmliang.tw@gmail.com>
Tested: verified that EINVAL is correctly returned when secretlen > len(secret)
Fixes: 4f4853dc ("ipv6: sr: implement API to control SR HMAC structure")
Signed-off-by: David Lebrun <dlebrun@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hangbin Liu says:

====================
bonding: fix lladdr finding and confirmation

This patch set fixed 3 issues when setting lladdr as bonding IPv6 target.
Please see each patch for the details.

v2: separate the patch to 3 parts
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The unsolicited NA message with all-nodes multicast dest address should
be valid, as this also means the link could reach the target.

Also rename bond_validate_ns() to bond_validate_na().
Reported-by: LiLiang <liali@redhat.com>
Fixes: 5e1eeef6 ("bonding: NS target should accept link local address")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a link is enslave to bond, it need to set the interface down first.
This makes the slave remove mac multicast address 33:33:00:00:00:01(The
IPv6 multicast address ff02::1 is kept even when the interface down). When
bond set the slave up, ipv6_mc_up() was not called due to commit c2edacf8
("bonding / ipv6: no addrconf for slaves separately from master").

This is not an issue before we adding the lladdr target feature for bonding,
as the mac multicast address will be added back when bond interface up and
join group ff02::1.

But after adding lladdr target feature for bonding. When user set a lladdr
target, the unsolicited NA message with all-nodes multicast dest will be
dropped as the slave interface never add 33:33:00:00:00:01 back.

Fix this by calling ipv6_mc_up() to add 33:33:00:00:00:01 back when
the slave interface up.
Reported-by: LiLiang <liali@redhat.com>
Fixes: 5e1eeef6 ("bonding: NS target should accept link local address")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When ns_ip6_target was set, the ipv6_dev_get_saddr() will be called to get
available source address and send IPv6 neighbor solicit message.

If the target is global address, ipv6_dev_get_saddr() will get any
available src address. But if the target is link local address,
ipv6_dev_get_saddr() will only get available address from our interface,
i.e. the corresponding bond interface.

But before bond interface up, all the address is tentative, while
ipv6_dev_get_saddr() will ignore tentative address. This makes we can't
find available link local src address, then bond_ns_send() will not be
called and no NS message was sent. Finally bond interface will keep in
down state.

Fix this by sending NS with unspecified address if there is no available
source address.
Reported-by: LiLiang <liali@redhat.com>
Fixes: 5e1eeef6 ("bonding: NS target should accept link local address")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Johannes berg says:

====================
We have a handful of fixes:
 - fix DMA from stack in wilc1000 driver
 - fix crash on chip reset failure in mt7921e
 - fix for the reported warning on aggregation timer expiry
 - check packet lengths in hwsim virtio paths
 - fix compiler warnings/errors with AAD construction by
   using struct_group
 - fix Intel 4965 driver rate scale operation
 - release channel contexts correctly in mac80211 mlme code
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We sometimes copy all the addresses from the 802.11 header
for the AAD, which may cause complaints from fortify checks.
Use struct_group() to avoid the compiler warnings/errors.

Change-Id: Ic3ea389105e7813b22095b295079eecdabde5045
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

An invalid packet with a length shorter than the specified length in the
netlink header can lead to use-after-frees and slab-out-of-bounds in the
processing of the netlink attributes, such as the following:

  BUG: KASAN: slab-out-of-bounds in __nla_validate_parse+0x1258/0x2010
  Read of size 2 at addr ffff88800ac7952c by task kworker/0:1/12

  Workqueue: events hwsim_virtio_rx_work
  Call Trace:
   <TASK>
   dump_stack_lvl+0x45/0x5d
   print_report.cold+0x5e/0x5e5
   kasan_report+0xb1/0x1c0
   __nla_validate_parse+0x1258/0x2010
   __nla_parse+0x22/0x30
   hwsim_virtio_handle_cmd.isra.0+0x13f/0x2d0
   hwsim_virtio_rx_work+0x1b2/0x370
   process_one_work+0x8df/0x1530
   worker_thread+0x575/0x11a0
   kthread+0x29d/0x340
   ret_from_fork+0x22/0x30
 </TASK>

Discarding packets with an invalid length solves this.
Therefore, skb->len must be set at reception.

Change-Id: Ieaeb9a4c62d3beede274881a7c2722c6c6f477b6
Signed-off-by: Soenke Huster <soenke.huster@eknoes.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If we hit an authentication or association timeout, we only
release the chanctx for the deflink, and the other link(s)
are released later by ieee80211_vif_set_links(), but we're
not locking this correctly.

Fix the locking here while releasing the channels and links.

Change-Id: I9e08c1a5434592bdc75253c1abfa6c788f9f39b1
Fixes: 81151ce4 ("wifi: mac80211: support MLO authentication/association with one link")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In the prep_channel error case we didn't release the deflink
channel leaving it to be left around. Fix that.

Change-Id: If0dfd748125ec46a31fc6045a480dc28e03723d2
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The rx data link pointer isn't set from the RX aggregation timer,
resulting in a later warning. Fix that by setting it to the first
valid link for now, with a FIXME to worry about statistics later,
it's not very important since it's just the timeout case.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/498d714c-76be-9d04-26db-a1206878de5e@redhat.com
Fixes: 56057da4 ("wifi: mac80211: rx: track link in RX data")
Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2022-09-02 (i40e, iavf)

This series contains updates to i40e and iavf drivers.

Przemyslaw adds reset to ADQ configuration to allow for setting of rate
limit beyond TC0 for i40e.

Ivan Vecera does not free client on failure to open which could cause
NULL pointer dereference to occur on i40e. He also detaches device
during reset to prevent NDO calls with could cause races for iavf.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
This series contains updates to ice driver only.

Przemyslaw fixes memory leak of DMA memory due to incorrect freeing of
rx_buf.

Michal S corrects incorrect call to free memory.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

After driver refactoring we was running ksz9477 specific CPU port
configuration on ksz8 family which ended with kernel oops. So, make sure
we run this code only on ksz9477 compatible devices.

Tested on KSZ8873 and KSZ9477.

Fixes: da8cd085 ("net: dsa: microchip: add support for common phylink mac link up")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Removing 'hotplug-status' in backend_disconnected() means that it will be
removed even in the case that the frontend unilaterally disconnects (which
it is free to do at any time). The consequence of this is that, when the
frontend attempts to re-connect, the backend gets stuck in 'InitWait'
rather than moving straight to 'Connected' (which it can do because the
hotplug script has already run).
Instead, the 'hotplug-status' mode should be removed in netback_remove()
i.e. when the vif really is going away.

Fixes: 0f4558ae ("Revert "xen-netback: remove 'hotplug-status' once it has served its purpose"")
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mutexes cannot be taken in a non-preemptible context,
causing a panic in `fec_ptp_save_state()`. Replacing
`ptp_clk_mutex` by `tmreg_lock` fixes this.

Fixes: 6a4d7234 ("net: fec: ptp: avoid register access when ipg clock is disabled")
Fixes: f7995922 ("fec: Restart PPS after link state change")
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/all/20220827160922.642zlcd5foopozru@pengutronix.de/Signed-off-by: Csókás Bence <csokas.bence@prolan.hu>
Tested-by: Francesco Dolcini <francesco.dolcini@toradex.com> # Toradex Apalis iMX6
Link: https://lore.kernel.org/r/20220901140402.64804-1-csokas.bence@prolan.huSigned-off-by: Jakub Kicinski <kuba@kernel.org>

There is a very low probability that tx timeout will occur during
suspend and resume stress test on imx6q platform. So we add pm_qos
support to prevent system from entering low level idles which may
affect the transmission of tx.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://lore.kernel.org/r/20220830070148.2021947-1-wei.fang@nxp.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Florian Westphal says:

====================
netfilter: bug fixes for net

1. Fix IP address check in irc DCC conntrack helper, this should check
   the opposite direction rather than the destination address of the
   packets' direction, from David Leadbeater.

2. bridge netfilter needs to drop dst references, from Harsh Modi.
   This was fine back in the day the code was originally written,
   but nowadays various tunnels can pre-set metadata dsts on packets.

3. Remove nf_conntrack_helper sysctl and the modparam toggle, users
   need to explicitily assign the helpers to use via nftables or
   iptables.  Conntrack helpers, by design, may be used to add dynamic
   port redirections to internal machines, so its necessary to restrict
   which hosts/peers are allowed to use them.
   It was discovered that improper checking in the irc DCC helper makes
   it possible to trigger the 'please do dynamic port forward'
   from outside by embedding a 'DCC' in a PING request; if the client
   echos that back a expectation/port forward gets added.
   The auto-assign-for-everything mechanism has been in "please don't do this"
   territory since 2012.  From Pablo.

4. Fix a memory leak in the netdev hook error unwind path, also from Pablo.

* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
  netfilter: nf_conntrack_irc: Fix forged IP logic
  netfilter: nf_tables: clean up hook list when offload flags check fails
  netfilter: br_netfilter: Drop dst references before setting.
  netfilter: remove nf_conntrack_helper sysctl and modparam toggles
====================

Link: https://lore.kernel.org/r/20220901071238.3044-1-fw@strlen.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

iavf_reset_task() takes crit_lock at the beginning and holds
it during whole call. The function subsequently calls
iavf_init_interrupt_scheme() that grabs RTNL. Problem occurs
when userspace initiates during the reset task any ndo callback
that runs under RTNL like iavf_open() because some of that
functions tries to take crit_lock. This leads to classic A-B B-A
deadlock scenario.

To resolve this situation the device should be detached in
iavf_reset_task() prior taking crit_lock to avoid subsequent
ndos running under RTNL and reattach the device at the end.

Fixes: 62fe2a86 ("i40evf: add missing rtnl_lock() around i40evf_set_interrupt_capability")
Cc: Jacob Keller <jacob.e.keller@intel.com>
Cc: Patryk Piotrowski <patryk.piotrowski@intel.com>
Cc: SlawomirX Laba <slawomirx.laba@intel.com>
Tested-by: Vitaly Grinberg <vgrinber@redhat.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

The driver incorrectly frees client instance and subsequent
i40e module removal leads to kernel crash.

Reproducer:
1. Do ethtool offline test followed immediately by another one
host# ethtool -t eth0 offline; ethtool -t eth0 offline
2. Remove recursively irdma module that also removes i40e module
host# modprobe -r irdma

Result:
[ 8675.035651] i40e 0000:3d:00.0 eno1: offline testing starting
[ 8675.193774] i40e 0000:3d:00.0 eno1: testing finished
[ 8675.201316] i40e 0000:3d:00.0 eno1: offline testing starting
[ 8675.358921] i40e 0000:3d:00.0 eno1: testing finished
[ 8675.496921] i40e 0000:3d:00.0: IRDMA hardware initialization FAILED init_state=2 status=-110
[ 8686.188955] i40e 0000:3d:00.1: i40e_ptp_stop: removed PHC on eno2
[ 8686.943890] i40e 0000:3d:00.1: Deleted LAN device PF1 bus=0x3d dev=0x00 func=0x01
[ 8686.952669] i40e 0000:3d:00.0: i40e_ptp_stop: removed PHC on eno1
[ 8687.761787] BUG: kernel NULL pointer dereference, address: 0000000000000030
[ 8687.768755] #PF: supervisor read access in kernel mode
[ 8687.773895] #PF: error_code(0x0000) - not-present page
[ 8687.779034] PGD 0 P4D 0
[ 8687.781575] Oops: 0000 [#1] PREEMPT SMP NOPTI
[ 8687.785935] CPU: 51 PID: 172891 Comm: rmmod Kdump: loaded Tainted: G        W I        5.19.0+ #2
[ 8687.794800] Hardware name: Intel Corporation S2600WFD/S2600WFD, BIOS SE5C620.86B.0X.02.0001.051420190324 05/14/2019
[ 8687.805222] RIP: 0010:i40e_lan_del_device+0x13/0xb0 [i40e]
[ 8687.810719] Code: d4 84 c0 0f 84 b8 25 01 00 e9 9c 25 01 00 41 bc f4 ff ff ff eb 91 90 0f 1f 44 00 00 41 54 55 53 48 8b 87 58 08 00 00 48 89 fb <48> 8b 68 30 48 89 ef e8 21 8a 0f d5 48 89 ef e8 a9 78 0f d5 48 8b
[ 8687.829462] RSP: 0018:ffffa604072efce0 EFLAGS: 00010202
[ 8687.834689] RAX: 0000000000000000 RBX: ffff8f43833b2000 RCX: 0000000000000000
[ 8687.841821] RDX: 0000000000000000 RSI: ffff8f4b0545b298 RDI: ffff8f43833b2000
[ 8687.848955] RBP: ffff8f43833b2000 R08: 0000000000000001 R09: 0000000000000000
[ 8687.856086] R10: 0000000000000000 R11: 000ffffffffff000 R12: ffff8f43833b2ef0
[ 8687.863218] R13: ffff8f43833b2ef0 R14: ffff915103966000 R15: ffff8f43833b2008
[ 8687.870342] FS:  00007f79501c3740(0000) GS:ffff8f4adffc0000(0000) knlGS:0000000000000000
[ 8687.878427] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 8687.884174] CR2: 0000000000000030 CR3: 000000014276e004 CR4: 00000000007706e0
[ 8687.891306] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 8687.898441] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 8687.905572] PKRU: 55555554
[ 8687.908286] Call Trace:
[ 8687.910737]  <TASK>
[ 8687.912843]  i40e_remove+0x2c0/0x330 [i40e]
[ 8687.917040]  pci_device_remove+0x33/0xa0
[ 8687.920962]  device_release_driver_internal+0x1aa/0x230
[ 8687.926188]  driver_detach+0x44/0x90
[ 8687.929770]  bus_remove_driver+0x55/0xe0
[ 8687.933693]  pci_unregister_driver+0x2a/0xb0
[ 8687.937967]  i40e_exit_module+0xc/0xf48 [i40e]

Two offline tests cause IRDMA driver failure (ETIMEDOUT) and this
failure is indicated back to i40e_client_subtask() that calls
i40e_client_del_instance() to free client instance referenced
by pf->cinst and sets this pointer to NULL. During the module
removal i40e_remove() calls i40e_lan_del_device() that dereferences
pf->cinst that is NULL -> crash.
Do not remove client instance when client open callbacks fails and
just clear __I40E_CLIENT_INSTANCE_OPENED bit. The driver also needs
to take care about this situation (when netdev is up and client
is NOT opened) in i40e_notify_client_of_netdev_close() and
calls client close callback only when __I40E_CLIENT_INSTANCE_OPENED
is set.

Fixes: 0ef2d5af ("i40e: KISS the client interface")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Helena Anna Dubel <helena.anna.dubel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Fix HW rate limiting for ADQ.
Fallback to kernel queue selection for ADQ, as it is network stack
that decides which queue to use for transmit with ADQ configured.
Reset PF after creation of VMDq2 VSIs required for ADQ, as to
reprogram TX queue contexts in i40e_configure_tx_ring.
Without this patch PF would limit TX rate only according to TC0.

Fixes: a9ce82f7 ("i40e: Enable 'channel' mode in mqprio for TC configs")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

pf->avail_txqs was allocated using bitmap_zalloc, bitmap_free should be
used to free this memory.

Fixes: 78b5713a ("ice: Alloc queue management bitmaps and arrays dynamically")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Fix leak, when user changes ring parameters.
During reallocation of RX buffers, new DMA mappings are created for
those buffers. New buffers with different RX ring count should
substitute older ones, but those buffers were freed in ice_vsi_cfg_rxq
and reallocated again with ice_alloc_rx_buf. kfree on rx_buf caused
leak of already mapped DMA.
Reallocate ZC with xdp_buf struct, when BPF program loads. Reallocate
back to rx_buf, when BPF program unloads.
If BPF program is loaded/unloaded and XSK pools are created, reallocate
RX queues accordingly in XDP_SETUP_XSK_POOL handler.

Steps for reproduction:
while :
do
	for ((i=0; i<=8160; i=i+32))
	do
		ethtool -G enp130s0f0 rx $i tx $i
		sleep 0.5
		ethtool -g enp130s0f0
	done
done

Fixes: 617f3e1b ("ice: xsk: allocate separate memory for XDP SW ring")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Chandan <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

David Howells says:

====================
rxrpc fixes
Here are some fixes for AF_RXRPC:

 (1) Fix the handling of ICMP/ICMP6 packets.  This is a problem due to
     rxrpc being switched to acting as a UDP tunnel, thereby allowing it to
     steal the packets before they go through the UDP Rx queue.  UDP
     tunnels can't get ICMP/ICMP6 packets, however.  This patch adds an
     additional encap hook so that they can.

 (2) Fix the encryption routines in rxkad to handle packets that have more
     than three parts correctly.  The problem is that ->nr_frags doesn't
     count the initial fragment, so the sglist ends up too short.

 (3) Fix a problem with destruction of the local endpoint potentially
     getting repeated.

 (4) Fix the calculation of the time at which to resend.
     jiffies_to_usecs() gives microseconds, not nanoseconds.

 (5) Fix AFS to work out when callback promises and locks expire based on
     the time an op was issued rather than the time the first reply packet
     arrives.  We don't know how long the server took between calculating
     the expiry interval and transmitting the reply.

 (6) Given (5), rxrpc_get_reply_time() is no longer used, so remove it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We got a recent syzbot report [1] showing a possible misuse
of pfmemalloc page status in TCP zerocopy paths.

Indeed, for pages coming from user space or other layers,
using page_is_pfmemalloc() is moot, and possibly could give
false positives.

There has been attempts to make page_is_pfmemalloc() more robust,
but not using it in the first place in this context is probably better,
removing cpu cycles.

Note to stable teams :

You need to backport 84ce071e ("net: introduce
__skb_fill_page_desc_noacc") as a prereq.

Race is more probable after commit c07aea3e
("mm: add a signature in struct page") because page_is_pfmemalloc()
is now using low order bit from page->lru.next, which can change
more often than page->index.

Low order bit should never be set for lru.next (when used as an anchor
in LRU list), so KCSAN report is mostly a false positive.

Backporting to older kernel versions seems not necessary.

[1]
BUG: KCSAN: data-race in lru_add_fn / tcp_build_frag

write to 0xffffea0004a1d2c8 of 8 bytes by task 18600 on cpu 0:
__list_add include/linux/list.h:73 [inline]
list_add include/linux/list.h:88 [inline]
lruvec_add_folio include/linux/mm_inline.h:105 [inline]
lru_add_fn+0x440/0x520 mm/swap.c:228
folio_batch_move_lru+0x1e1/0x2a0 mm/swap.c:246
folio_batch_add_and_move mm/swap.c:263 [inline]
folio_add_lru+0xf1/0x140 mm/swap.c:490
filemap_add_folio+0xf8/0x150 mm/filemap.c:948
__filemap_get_folio+0x510/0x6d0 mm/filemap.c:1981
pagecache_get_page+0x26/0x190 mm/folio-compat.c:104
grab_cache_page_write_begin+0x2a/0x30 mm/folio-compat.c:116
ext4_da_write_begin+0x2dd/0x5f0 fs/ext4/inode.c:2988
generic_perform_write+0x1d4/0x3f0 mm/filemap.c:3738
ext4_buffered_write_iter+0x235/0x3e0 fs/ext4/file.c:270
ext4_file_write_iter+0x2e3/0x1210
call_write_iter include/linux/fs.h:2187 [inline]
new_sync_write fs/read_write.c:491 [inline]
vfs_write+0x468/0x760 fs/read_write.c:578
ksys_write+0xe8/0x1a0 fs/read_write.c:631
__do_sys_write fs/read_write.c:643 [inline]
__se_sys_write fs/read_write.c:640 [inline]
__x64_sys_write+0x3e/0x50 fs/read_write.c:640
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x2b/0x70 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd

read to 0xffffea0004a1d2c8 of 8 bytes by task 18611 on cpu 1:
page_is_pfmemalloc include/linux/mm.h:1740 [inline]
__skb_fill_page_desc include/linux/skbuff.h:2422 [inline]
skb_fill_page_desc include/linux/skbuff.h:2443 [inline]
tcp_build_frag+0x613/0xb20 net/ipv4/tcp.c:1018
do_tcp_sendpages+0x3e8/0xaf0 net/ipv4/tcp.c:1075
tcp_sendpage_locked net/ipv4/tcp.c:1140 [inline]
tcp_sendpage+0x89/0xb0 net/ipv4/tcp.c:1150
inet_sendpage+0x7f/0xc0 net/ipv4/af_inet.c:833
kernel_sendpage+0x184/0x300 net/socket.c:3561
sock_sendpage+0x5a/0x70 net/socket.c:1054
pipe_to_sendpage+0x128/0x160 fs/splice.c:361
splice_from_pipe_feed fs/splice.c:415 [inline]
__splice_from_pipe+0x222/0x4d0 fs/splice.c:559
splice_from_pipe fs/splice.c:594 [inline]
generic_splice_sendpage+0x89/0xc0 fs/splice.c:743
do_splice_from fs/splice.c:764 [inline]
direct_splice_actor+0x80/0xa0 fs/splice.c:931
splice_direct_to_actor+0x305/0x620 fs/splice.c:886
do_splice_direct+0xfb/0x180 fs/splice.c:974
do_sendfile+0x3bf/0x910 fs/read_write.c:1249
__do_sys_sendfile64 fs/read_write.c:1317 [inline]
__se_sys_sendfile64 fs/read_write.c:1303 [inline]
__x64_sys_sendfile64+0x10c/0x150 fs/read_write.c:1303
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x2b/0x70 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd

value changed: 0x0000000000000000 -> 0xffffea0004a1d288

Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 18611 Comm: syz-executor.4 Not tainted 6.0.0-rc2-syzkaller-00248-ge022620b-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 07/22/2022

Fixes: c07aea3e ("mm: add a signature in struct page")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Shakeel Butt <shakeelb@google.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a shift wrapping bug in this code so anything thing above
31 will return false.

Fixes: 35c55c98 ("tipc: add neighbor monitoring framework")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The sch_sfb enqueue() routine assumes the skb is still alive after it has
been enqueued into a child qdisc, using the data in the skb cb field in the
increment_qlen() routine after enqueue. However, the skb may in fact have
been freed, causing a use-after-free in this case. In particular, this
happens if sch_cake is used as a child of sfb, and the GSO splitting mode
of CAKE is enabled (in which case the skb will be split into segments and
the original skb freed).

Fix this by copying the sfb cb data to the stack before enqueueing the skb,
and using this stack copy in increment_qlen() instead of the skb pointer
itself.

Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-18231
Fixes: e13e02a3 ("net_sched: SFB flow scheduler")
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 2c87c6f9.
Meanwhile it turned out that the following commit is the proper
workaround for the issue that 2c87c6f9 tries to address.
a3a57bf0 ("net: stmmac: work around sporadic tx issue on link-up")
It's nor clear why the to be reverted commit helped for one user,
for others it didn't make a difference.

Fixes: 2c87c6f9 ("net: phy: meson-gxl: improve link-up behavior")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/8deeeddc-6b71-129b-1918-495a12dc11e3@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Pull networking fixes from Paolo Abeni:
 "Including fixes from bluetooth, bpf and wireless.

  Current release - regressions:

   - bpf:
      - fix wrong last sg check in sk_msg_recvmsg()
      - fix kernel BUG in purge_effective_progs()

   - mac80211:
      - fix possible leak in ieee80211_tx_control_port()
      - potential NULL dereference in ieee80211_tx_control_port()

  Current release - new code bugs:

   - nfp: fix the access to management firmware hanging

  Previous releases - regressions:

   - ip: fix triggering of 'icmp redirect'

   - sched: tbf: don't call qdisc_put() while holding tree lock

   - bpf: fix corrupted packets for XDP_SHARED_UMEM

   - bluetooth: hci_sync: fix suspend performance regression

   - micrel: fix probe failure

  Previous releases - always broken:

   - tcp: make global challenge ack rate limitation per net-ns and
     default disabled

   - tg3: fix potential hang-up on system reboot

   - mac802154: fix reception for no-daddr packets

  Misc:

   - r8152: add PID for the lenovo onelink+ dock"

* tag 'net-6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (56 commits)
  net/smc: Remove redundant refcount increase
  Revert "sch_cake: Return __NET_XMIT_STOLEN when consuming enqueued skb"
  tcp: make global challenge ack rate limitation per net-ns and default disabled
  tcp: annotate data-race around challenge_timestamp
  net: dsa: hellcreek: Print warning only once
  ip: fix triggering of 'icmp redirect'
  sch_cake: Return __NET_XMIT_STOLEN when consuming enqueued skb
  selftests: net: sort .gitignore file
  Documentation: networking: correct possessive "its"
  kcm: fix strp_init() order and cleanup
  mlxbf_gige: compute MDIO period based on i1clk
  ethernet: rocker: fix sleep in atomic context bug in neigh_timer_handler
  net: lan966x: improve error handle in lan966x_fdma_rx_get_frame()
  nfp: fix the access to management firmware hanging
  net: phy: micrel: Make the GPIO to be non-exclusive
  net: virtio_net: fix notification coalescing comments
  net/sched: fix netdevice reference leaks in attach_default_qdiscs()
  net: sched: tbf: don't call qdisc_put() while holding tree lock
  net: Use u64_stats_fetch_begin_irq() for stats fetch.
  net: dsa: xrs700x: Use irqsave variant for u64 stats update
  ...

Pull slab fix from Vlastimil Babka:

 - A fix from Waiman Long to avoid a theoretical deadlock reported by
   lockdep.

* tag 'slab-for-6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab:
  mm/slab_common: Deleting kobject in kmem_cache_destroy() without holding slab_mutex/cpu_hotplug_lock

Pull sound fixes from Takashi Iwai:
 "Just handful changes at this time. The only major change is the
  regression fix about the x86 WC-page buffer allocation.

  The rest are trivial data-race fixes for ALSA sequencer core, the
  possible out-of-bounds access fixes in the new ALSA control hash code,
  and a few device-specific workarounds and fixes"

* tag 'sound-6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: usb-audio: Add quirk for LH Labs Geek Out HD Audio 1V5
  ALSA: hda/realtek: Add speaker AMP init for Samsung laptops with ALC298
  ALSA: control: Re-order bounds checking in get_ctl_id_hash()
  ALSA: control: Fix an out-of-bounds bug in get_ctl_id_hash()
  ALSA: hda: intel-nhlt: Correct the handling of fmt_config flexible array
  ALSA: seq: Fix data-race at module auto-loading
  ALSA: seq: oss: Fix data-race for max_midi_devs access
  ALSA: memalloc: Revive x86-specific WC page allocations again

Remove rxrpc_get_reply_time() as that is no longer used now that the call
issue time is used instead of the reply time.
Signed-off-by: David Howells <dhowells@redhat.com>

rxrpc and kafs between them try to use the receive timestamp on the first
data packet (ie. the one with sequence number 1) as a base from which to
calculate the time at which callback promise and lock expiration occurs.

However, we don't know how long it took for the server to send us the reply
from it having completed the basic part of the operation - it might then,
for instance, have to send a bunch of a callback breaks, depending on the
particular operation.

Fix this by using the time at which the operation is issued on the client
as a base instead.  That should never be longer than the server's idea of
the expiry time.

Fixes: 78107055 ("afs: Fix calculation of callback expiry time")
Fixes: 2070a3e4 ("rxrpc: Allow the reply time to be obtained on a client call")
Suggested-by: Jeffrey E Altman <jaltman@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>

Fix the calculation of the resend age to add a microsecond value as
microseconds, not nanoseconds.
Signed-off-by: David Howells <dhowells@redhat.com>

If the local processor work item for the rxrpc local endpoint gets requeued
by an event (such as an incoming packet) between it getting scheduled for
destruction and the UDP socket being closed, the rxrpc_local_destroyer()
function can get run twice.  The second time it can hang because it can end
up waiting for cleanup events that will never happen.
Signed-off-by: David Howells <dhowells@redhat.com>

rxkad_verify_packet_2() has a small stack-allocated sglist of 4 elements,
but if that isn't sufficient for the number of fragments in the socket
buffer, we try to allocate an sglist large enough to hold all the
fragments.

However, for large packets with a lot of fragments, this isn't sufficient
and we need at least one additional fragment.

The problem manifests as skb_to_sgvec() returning -EMSGSIZE and this then
getting returned by userspace.  Most of the time, this isn't a problem as
rxrpc sets a limit of 5692, big enough for 4 jumbo subpackets to be glued
together; occasionally, however, the server will ignore the reported limit
and give a packet that's a lot bigger - say 19852 bytes with ->nr_frags
being 7.  skb_to_sgvec() then tries to return a "zeroth" fragment that
seems to occur before the fragments counted by ->nr_frags and we hit the
end of the sglist too early.

Note that __skb_to_sgvec() also has an skb_walk_frags() loop that is
recursive up to 24 deep.  I'm not sure if I need to take account of that
too - or if there's an easy way of counting those frags too.

Fix this by counting an extra frag and allocating a larger sglist based on
that.

Fixes: d0d5c0cd ("rxrpc: Use skb_unshare() rather than skb_cow_data()")
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-afs@lists.infradead.org

Because rxrpc pretends to be a tunnel on top of a UDP/UDP6 socket, allowing
it to siphon off UDP packets early in the handling of received UDP packets
thereby avoiding the packet going through the UDP receive queue, it doesn't
get ICMP packets through the UDP ->sk_error_report() callback.  In fact, it
doesn't appear that there's any usable option for getting hold of ICMP
packets.

Fix this by adding a new UDP encap hook to distribute error messages for
UDP tunnels.  If the hook is set, then the tunnel driver will be able to
see ICMP packets.  The hook provides the offset into the packet of the UDP
header of the original packet that caused the notification.

An alternative would be to call the ->error_handler() hook - but that
requires that the skbuff be cloned (as ip_icmp_error() or ipv6_cmp_error()
do, though isn't really necessary or desirable in rxrpc's case is we want
to parse them there and then, not queue them).

Changes
=======
ver #3)
 - Fixed an uninitialised variable.

ver #2)
 - Fixed some missing CONFIG_AF_RXRPC_IPV6 conditionals.

Fixes: 5271953c ("rxrpc: Use the UDP encap_rcv hook")
Signed-off-by: David Howells <dhowells@redhat.com>

mm/slab_common: Deleting kobject in kmem_cache_destroy() without holding slab_mutex/cpu_hotplug_lock

A circular locking problem is reported by lockdep due to the following
circular locking dependency.

  +--> cpu_hotplug_lock --> slab_mutex --> kn->active --+
  |                                                     |
  +-----------------------------------------------------+

The forward cpu_hotplug_lock ==> slab_mutex ==> kn->active dependency
happens in

  kmem_cache_destroy():	cpus_read_lock(); mutex_lock(&slab_mutex);
  ==> sysfs_slab_unlink()
      ==> kobject_del()
          ==> kernfs_remove()
	      ==> __kernfs_remove()
	          ==> kernfs_drain(): rwsem_acquire(&kn->dep_map, ...);

The backward kn->active ==> cpu_hotplug_lock dependency happens in

  kernfs_fop_write_iter(): kernfs_get_active();
  ==> slab_attr_store()
      ==> cpu_partial_store()
          ==> flush_all(): cpus_read_lock()

One way to break this circular locking chain is to avoid holding
cpu_hotplug_lock and slab_mutex while deleting the kobject in
sysfs_slab_unlink() which should be equivalent to doing a write_lock
and write_unlock pair of the kn->active virtual lock.

Since the kobject structures are not protected by slab_mutex or the
cpu_hotplug_lock, we can certainly release those locks before doing
the delete operation.

Move sysfs_slab_unlink() and sysfs_slab_release() to the newly
created kmem_cache_release() and call it outside the slab_mutex &
cpu_hotplug_lock critical sections. There will be a slight delay
in the deletion of sysfs files if kmem_cache_release() is called
indirectly from a work function.

Fixes: 5a836bf6 ("mm: slub: move flush_cpu_slab() invocations __free_slab() invocations out of IRQ context")
Signed-off-by: Waiman Long <longman@redhat.com>
Reviewed-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Reviewed-by: Roman Gushchin <roman.gushchin@linux.dev>
Acked-by: David Rientjes <rientjes@google.com>
Link: https://lore.kernel.org/all/YwOImVd+nRUsSAga@hyeyoo/Signed-off-by: Vlastimil Babka <vbabka@suse.cz>

For passive connections, the refcount increment has been done in
smc_clcsock_accept()-->smc_sock_alloc().

Fixes: 3b2dec26 ("net/smc: restructure client and server code in af_smc")
Signed-off-by: Yacan Liu <liuyacan@corp.netease.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Link: https://lore.kernel.org/r/20220830152314.838736-1-liuyacan@corp.netease.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>