We set the capacity to zero when we discovered a device formatted with
an unknown DIF protection type. However, the read_capacity code would
override the capacity and cause the device to be enabled regardless.

Make sd_read_protection_type() return an error if the protection type is
unknown. Also prevent duplicate printk lines when the device is being
revalidated.
Reported-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

In case of FW hung ISP83XX generates continuous pause frames
which causes switch to disable port.
Added fix to disable generating pause frames in case of
FW hung
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Issue:
For ISP83XX risc_intr getting clear two times in case of polling mode.
risc_intr getting clear from interrupt_service_routine() as well
from process_mbox_intr() because of this driver may clear risc_intr
without processing interrupt.

Fix:
Do not clear risc_intr from process_mbox_intr().
Signed-off-by: Manish Dusane <manish.dusane@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Handle IDC Request Notify AEN and post IDC Acknowledgement
while participating in Loopback IDC.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Issue:
System panic on rmmod if probe_adapter had failed during driver load.

Call Trace:
 [<ffffffffa071aa5a>] qla4xxx_abort_active_cmds+0x4a/0xa0 [qla4xxx]
 [<ffffffffa07224db>] qla4xxx_free_adapter+0x1b/0x1b0 [qla4xxx]
 [<ffffffffa073991f>] qla4xxx_remove_adapter+0x294/0x2c7 [qla4xxx]
 [<ffffffff812930b7>] pci_device_remove+0x37/0x70
 [<ffffffff8135006f>] __device_release_driver+0x6f/0xe0
 [<ffffffff813501a8>] driver_detach+0xc8/0xd0
 [<ffffffff8134ef0e>] bus_remove_driver+0x8e/0x110
 [<ffffffff81350972>] driver_unregister+0x62/0xa0
 [<ffffffff812933c4>] pci_unregister_driver+0x44/0xb0
 [<ffffffffa0739659>] qla4xxx_module_exit+0x15/0x47 [qla4xxx]
 [<ffffffff810addd4>] sys_delete_module+0x194/0x260
 [<ffffffff8150326e>] ? do_page_fault+0x3e/0xa0
 [<ffffffff8100b0f2>] system_call_fastpath+0x16/0x1b

Fix:
Do not cleanup resources on remove_adapter as they are cleaned up during
probe_adapter exit.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

If IRQ allocation fails, it means system has run out of interrupt
vectors, so fail probe_adapter in case of IRQ allocation failure
and dont retry adapter initialization.
Signed-off-by: Poornima Vonti <poornima.vonti@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

For ISP82xx mixed interrupt mode is not supported.
Hence prevent MSI/MSI-x from falling back to INTx mode.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Camram is reset by FW to default values after reboot/cold boot/pci reset.
In case of AER, PCI may need to reset so we need to set correct idc reg value
after PCIE error.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Issue:
In qla4_8xxx_error_recovery() IDC lock recovery is initiated as
IDC lock is held while enabling the interrupts

Fix:
Correctly handle IDC locking mechanism in qla4_8xxx_error_recovery().
Signed-off-by: Poornima Vonti <poornima.vonti@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: Manish Dusane <manish.dusane@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

A quote from SPC-4: "While in the unavailable primary target port
asymmetric access state, the device server shall support those of
the following commands that it supports while in the active/optimized
state: [ ... ] d) SET TARGET PORT GROUPS; [ ... ]". Hence enable
sending STPG to a target port group that is in the unavailable state.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Hannes Reinecke <hare@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

John reports:
 BUG: soft lockup - CPU#2 stuck for 23s! [kworker/u:8:2202]
 [..]
 Call Trace:
  [<ffffffff8141782a>] scsi_remove_target+0xda/0x1f0
  [<ffffffff81421de5>] sas_rphy_remove+0x55/0x60
  [<ffffffff81421e01>] sas_rphy_delete+0x11/0x20
  [<ffffffff81421e35>] sas_port_delete+0x25/0x160
  [<ffffffff814549a3>] mptsas_del_end_device+0x183/0x270

...introduced by commit 3b661a92 "[SCSI] fix hot unplug vs async scan race".

Don't restart lookup of more stargets in the multi-target case, just
arrange to traverse the list once, on the assumption that new targets
are always added at the end.  There is no guarantee that the target will
change state in scsi_target_reap() so we can end up spinning if we
restart.

Cc: <stable@vger.kernel.org>
Acked-by: Jack Wang <jack_wang@usish.com>
LKML-Reference: <CAEhu1-6wq1YsNiscGMwP4ud0Q+MrViRzv=kcWCQSBNc8c68N5Q@mail.gmail.com>
Reported-by: John Drescher <drescherjm@gmail.com>
Tested-by: John Drescher <drescherjm@gmail.com>
Signed-off-by: Dan Williams <djbw@fb.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

The length field in the host config packet is only 16-bit long, so
passing it 0x10000 (64K which is our standard PAGE_SIZE) doesn't
work and result in an empty config from the server.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <stable@vger.kernel.org>
Acked-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Now that the iSeries code is gone the backend abstraction
in this driver is no longer necessary, which allows us to
consolidate the driver in one file.

The side effect is that the module name is now ibmvscsi.ko
which matches the driver hotplug name and fixes auto-load
issues.

[jejb:fix up checkpatch.pl errors]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: Poornima Vonti <poornima.vonti@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Move minidump code from qla4_8xxx_device_bootstrap() to
new function qla4_8xxx_get_minidump() to make code more
modular.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Issue:
   Device can go to READY state from COLD and skip INITIALIZATION,
   In this case driver will never set IDC version from function
   qla4_8xxx_device_bootstrap().

Fix:
1. Set IDC version at start of function qla4_82xx_need_reset_handler().
2. Set IDC version only if we are 1st driver to load.
3. Added new function qla4_8xxx_update_idc_reg() to set all idc reg at one
   place.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: Poornima Vonti <poornima.vonti@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Remove following unused define:-

QLA82XX_MINIDUMP_OCM0_SIZE
QLA82XX_MINIDUMP_L1C_SIZE
QLA82XX_MINIDUMP_L2C_SIZE
QLA82XX_MINIDUMP_COMMON_STR_SIZE
QLA82XX_MINIDUMP_FCOE_STR_SIZE
QLA82XX_MINIDUMP_MEM_SIZE
QLA82XX_MAX_ENTRY_HDR

Added following new define to optimize code:-

MIU_TA_CTL_WRITE_ENABLE
MIU_TA_CTL_WRITE_START
MIU_TA_CTL_START_ENABLE
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

ql4_8xxx_mark_entry_skipped to qla4_8xxx_mark_entry_skipped
ql4_attr_is_visible to qla4_attr_is_visible
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Add "removable" module parameter to set the "removable" attribute of any
subsequently created debug block device. It is a writable driver option, so
that you can switch between removable and "fixed" media block devices in
between the add_host calls.

This is useful for being able to test the different behaviour/required
privileges in e. g. the udisks test suite.
Signed-off-by: Martin Pitt <martin.pitt@ubuntu.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

while processing the stop firmware mailbox command on driver unload,
a interrupt is processed which causes kernel panic as the response
queue is not valid.

Fix is to clear the interrupt in free_adapter call just after
disabling the interrupts.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Fix following lockdep warning:-

 INFO: trying to register non-static key.
 the code is fine but needs lockdep annotation.
 turning off the locking correctness validator.
 Pid: 298, comm: modprobe Not tainted 3.6.0-rc1+ #13
 Call Trace:
 [<c049f5c6>] register_lock_class+0x186/0x360
 [<c06e2e39>] ? __dev_printk+0x139/0x280
 [<c04a288a>] __lock_acquire+0x6a/0x450
 [<c04a2cf4>] lock_acquire+0x84/0xf0
 [<f98bb0d0>] ? qla4xxx_post_work+0x20/0x60 [qla4xxx]
 [<c089a05b>] _raw_spin_lock_irqsave+0x4b/0x60
 [<f98bb0d0>] ? qla4xxx_post_work+0x20/0x60 [qla4xxx]
 [<f98bb0d0>] qla4xxx_post_work+0x20/0x60 [qla4xxx]
 [<f98bb1c9>] qla4xxx_post_aen_work+0x49/0x60 [qla4xxx]
 [<f98c6cf2>] qla4xxx_isr_decode_mailbox+0x3f2/0x780 [qla4xxx]
 [<f98c8493>] qla4_83xx_interrupt_service_routine+0x33/0x50 [qla4xxx]
 [<f98d0e49>] qla4_83xx_process_mbox_intr+0x29/0x40 [qla4xxx]
 [<f98c2031>] qla4xxx_mailbox_command+0x361/0x5d0 [qla4xxx]
 [<c08983c8>] ? mutex_unlock+0x8/0x10
 [<f98c3e86>] qla4xxx_get_ifcb+0x66/0xb0 [qla4xxx]
 [<f98c3ef7>] qla4xxx_update_local_ifcb+0x27/0x100 [qla4xxx]
 [<f98c56af>] qla4xxx_initialize_fw_cb+0x2ff/0x3b0 [qla4xxx]
 [<c04150d0>] ? dma_generic_free_coherent+0x30/0x30
 [<f98c0f70>] qla4xxx_init_firmware+0x40/0xf0 [qla4xxx]
 [<f98c10b6>] qla4xxx_initialize_adapter+0x96/0x120 [qla4xxx]
 [<f98d35cd>] qla4xxx_probe_adapter+0x378/0x855 [qla4xxx]
 [<c04a1a04>] ? trace_hardirqs_on_caller+0xf4/0x180
 [<c04a1a9b>] ? trace_hardirqs_on+0xb/0x10
 [<c06ef403>] ? pm_runtime_enable+0x43/0x70
 [<c062f042>] local_pci_probe+0x42/0xb0
 [<c06300c0>] pci_device_probe+0x60/0x80
 [<c06e6bb6>] really_probe+0x56/0x2e0
 [<c089a5f2>] ? _raw_spin_unlock_irq+0x22/0x30
 [<c06f0b02>] ? pm_runtime_barrier+0x52/0xb0
 [<c06e6e77>] driver_probe_device+0x37/0x90
 [<c0898281>] ? mutex_lock_nested+0x31/0x40
 [<c06e6f51>] __driver_attach+0x81/0x90
 [<c06e51e8>] bus_for_each_dev+0x48/0x70
 [<c06e68e9>] driver_attach+0x19/0x20
 [<c06e6ed0>] ? driver_probe_device+0x90/0x90
 [<c06e637f>] bus_add_driver+0x18f/0x280
 [<c062ff40>] ? pci_dev_put+0x20/0x20
 [<c062ff40>] ? pci_dev_put+0x20/0x20
 [<c06e7435>] driver_register+0x65/0x120
 [<c061a3a2>] ? __raw_spin_lock_init+0x32/0x60
 [<c06302f4>] __pci_register_driver+0x54/0xc0
 [<f98e809e>] qla4xxx_module_init+0x9e/0xcd [qla4xxx]
 [<c040302f>] do_one_initcall+0x2f/0x170
 [<f98e8000>] ? 0xf98e7fff
 [<c04ae025>] sys_init_module+0x75/0x1c0
 [<c04a1a04>] ? trace_hardirqs_on_caller+0xf4/0x180
 [<c0609514>] ? trace_hardirqs_on_thunk+0xc/0x10
 [<c08a141f>] sysenter_do_call+0x12/0x38
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

We always assign a dummy task context to a port in order to address a
silicon issue. We have 4 ports per controller. So when idle, there are always
exactly 4 TCs "active". The adaptive interrupt coalescing code uses number of
active TCs to figure out the coalescing values. However, we never hit "0" TCs
because of the 4 dummy TCs. Putting in fix so that we calculate this correctly.
Reported-by: Dan Melnic <dan@seamicro.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

This commit fixes a driver bug for SSP tasks that require task management
in the target after they complete in the SCU hardware.  The problem was
manifested in the function "isci_task_abort_task", which tests
to see if the sas_task.lldd_task is non-NULL before allowing task
management; this bug would always NULL lldd_task in the SCU I/O completion
path even if target management was required, which would prevent
task / target manangement from happening.

Note that in the case of SATA/STP targets, error recovery is provided by
the libata error handler which is why SATA/STP device recovery worked
correctly even though SSP handling did not.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

This header file is included in user space applications
that are doing "FC Passthrough." This include causes
them to also include scsi/scsi.h. Since this header
file doesn't actually need scsi/scsi.h, remove the
include line.

This patch was tested with 'make allyesconfig'.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: Babu Moger <babu.moger@netapp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>