If a device reset has started, there is a chance that the heartbeat
function will fail because the device is disabled at the beginning
of the reset function.

In that case, we don't want the error message to appear in the log.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

A new uAPI is added for debug purposes of the user-space to retrieve
errors related data from previous session (before device reset was
performed).

Inforamtion is filled when a razwi or CS timeout happens and can
contain one of the following:

1. Retrieve timestamp of last time the device was opened and razwi or
   CS timeout happened.
2. Retrieve information about last CS timeout.
3. Retrieve information about last razwi error.

This information doesn't contain user data, so no danger of data
leakage between users.
Signed-off-by: Dani Liberman <dliberman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

AS TPM error indication is not fatal, driver should dump a warning
and continue booting.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

I2C debugfs support is limited to 1 byte. We extend functionality
to more than 1 byte by using one of the pad fields as a length.
No backward compatibility issues as new F/W versions will treat 0
length as a 1 byte length transaction.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Divide the code into 3 different parts:
- Copy kernel parameters
- Setting device behaivor per asic
- Fixup of various device parameters according to the device behaivor.

In addition, remove non-relevant code for upstream (simulator support).
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Add implementation for new opcodes in the INFO IOCTL:
1. Retrieve the replaced DRAM rows from f/w.
2. Retrieve the pending DRAM rows from f/w.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Refactor the wait-for-user-interrupt routine to make it more
generic for re-use for other user exposed h/w interfaces in future
ASICs.
Signed-off-by: Bharat Jauhari <bjauhari@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

In Signaling-From-Graph case, the driver didn't set the hw_sob pointer
at the right place, which is needed for the cs completion
check prior to start sending all the master/slaves jobs to device.
Signed-off-by: farah kassabri <fkassabri@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

In addition to the clock throttling reason, user should be able
to obtain also the start time and the duration of the throttling
event.
Signed-off-by: Ofir Bitton <obitton@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

In order to increase maximum wait-for-interrupt timeout, change it
to 64 bit variable. This wait is used only by newer ASICs, so no
problem in changing this interface at this time.
Signed-off-by: Dani Liberman <dliberman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Rename reset flags for better readability as compared to
HL_RESET_CAUSE* enum shared with the f/w.
Signed-off-by: Bharat Jauhari <bjauhari@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

CPUCP_PACKET_POWER_GET packet type was used for both
hl_get_power() and hl_set_power().

To align with other sensor functions hl_set_power()
should use CPUCP_PACKET_POWER_SET.

This packet will only be used with newer ASICs, so need to add
a compatibility flag to the asic properties to indicate whether to use
this packet or the GET packet.
Signed-off-by: Rajaravi Krishna Katta <rkatta@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

In case of device reset, the driver does a force trigger on all waiting
users to release them from waiting. However, the driver does not handle
error scenario while waiting.

hl_interrupt_wait_ioctl() now exits the wait in case of an error with
abort status.
Signed-off-by: Bharat Jauhari <bjauhari@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Once we read indication of whether f/w is doing the reset, we don't
want to clear it, until the next time we read this indication.

Otherwise, we might be in a state of wrong indication.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Using a variable poll interval for fw loading allows us to support
much slower environments (emulation) while changing only a single
line in the code, instead of choosing a different interval in each
function that polls.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Up until now the driver stored indication if Linux was loaded on the
device CPU. This was needed in order to coordinate some tasks that are
performed by the Linux.

In future ASICs, many of those tasks will be performed by the boot
fit, so now we need the same indication of boot fit load status.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

The PCI MMU cache is two layered. The upper layer, memcache, uses cache
lines, the bottom layer doesn't.

Hence, after PMMU map operation we have to invalidate memcache, to avoid
the situation where the new entry is already in the cache due to its
cache line being fully in the cache.

However, we do not have to invalidate the lower cache, and here we can
optimize, since cache invalidation is time consuming.
Signed-off-by: Yuri Nudelman <ynudelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

The enum vm_type was abused, used once as a value (indication
memory type for map) and once as a flag (for cache invalidation).
This makes it hard to add new and still keep it meaningful, hence it
is better to split into one enum for values and one for flags.
Signed-off-by: Yuri Nudelman <ynudelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Currently LAST_MASK is a global, but really it is an MMU implementation
specific. We need this change for future ASICs.
Signed-off-by: Yuri Nudelman <ynudelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

VA blocks are currently stored in an inconsistent way. Sometimes block
end is inclusive, sometimes exclusive. This leads to wrong size
calculations in certain cases, plus could lead to a segmentation fault
in case mapping process fails in the middle and we try to roll it back.
Need to make this consistent - start inclusive till end inclusive.

For example, the regions table may now look like this:
    0x0000 - 0x1fff : allocated
    0x2000 - 0x2fff : free
    0x3000 - 0x3fff : allocated
Signed-off-by: Yuri Nudelman <ynudelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Do not use a dma channel for debugfs requested transfer if it's
QM is not idle.
Signed-off-by: Guy Zadicario <gzadicario@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

The boot status flag "SRAM available" can be set by f/w Linux (in the
general case) or by f/w uboot (in some specific debug scenario) but
never by f/w preboot.

Hence, when polling the boot status flags in the preboot stage we do not
want to poll on "SRAM Avialable".

The special case in which uboot set this flag is when we are running
special debug scenario without Linux. In this case, at some point during
the boot, the uboot relocates its code to the DRAM and then set the
specified flag.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

VA range info could assist in debugging VA allocation bugs.
Signed-off-by: Yuri Nudelman <ynudelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

There are rare cases where the device CPU's watchdog has expired and as
a result, the watchdog reset has happened and the CPU will now move to
running its preboot f/w.

When that happens, the driver will only know that a heartbeat failure
occurred. As a result, the driver will send a message to the CPU's main
f/w asking it to reset the device, but because the CPU is now running
preboot, it won't respond and the re-initialization process will later
fail when trying to load the f/w.

The solution is to send the request to the preboot as well, only if the
reset was caused because of HB failure.
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

In the dynamic FW load protocol the boot status is updated to
"Ready to Boot" once uboot is active.

Polling on other boot status values is a residue of code duplication
from the static protocol and should be removed.
Signed-off-by: Ohad Sharabi <osharabi@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>

Merge tag 'iio-for-5.17a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next

Jonathan writes:

1st set of IIO new device support, features and cleanup for 5.17

Includes some fixes that were either late breaking, low priority or
complex enough to not be good to rush in late in the cycle.

Tree rebased today to fix up some trivial issues + pull in a fix that
was previously on the fixes-togreg branch. Vast majority have been
in linux-next for some time now.

New device support
* adi,ad7293
  - New driver and bindings for this Power Amplifier drain current
    controller.  A complex device with various related monitoring functions.
* adi,ad75513R
  - New driver and bindings for this combined ADC and DAC device.
  - A few follow up fixes.
* adi,admv8818
  - New driver (and type) for this 2-18GHz filter device. Includes
    bindings and ABI documentation to allow clk_notifier based auto
    adjustment of the filters in appropriate applications.
* liteon,ltr501
  - Support for the ltr303.  ID and chip specific info table.
* xilinx,ams
  - New generic firmware function fwnode_iomap() as used in this driver.
  - New driver and bindings for this ADC and on-chip sensors as found
    in various Xilinx devices.

Core
* Introduced IIO_VAL_INT_64 which uses val and val2 in IIO callbacks to
  form a 64 bit integer when higher precision needed.
* Allow IIO_ENUM_AVAILABLE to be used with different shared values.
* Fix a long term issue with scheduling whilst atomic when iio_trig_poll()
  is called but no trigger consumers are actually enabled and hence the
  trigger may be reenabled from the interrupt handler.  Seen in the wild
  on the tsc2046.
* Mark iio_device_type const.
* buffer: Use a separate index variable to simplify code.
* buffer-dma: Clear out unused struct iio_buffer_block
* buffer-dmaengine: Switch to cheaper round_down() as power of 2 values.

Tests/tools
* format_value
  - Check against NULL returns from allocations in tests.
  - Add IIO_VAL_INT_64 test case.
* event_monitor
  - Flush the output after event to given more consistent latency
    when tool output piped to other programs.

Driver Features
* axp20x
  - Add support for NTC thermistor channel and document TS pin binding.
* arm,scmi
  - Add reading of raw channel values (using IIO_VAL_INT_64)
* liteon,ltr501
  - Add proximity-near-level support and dt-binding.

Tree wide cleanup
* Remove no-op trigger ops from multiple drivers.
* Stop using dev_get_drvdata() on the iio_dev->dev in various drivers
  and then stop assigning it to allow this to be used for other purposes.
  We can always get to the indio_dev using dev_to_iio_dev() which is
  a container_of() based approach. Also cleanup up some related unnecessary
  convoluted cases.
  - atmel,at91-sam5d2
  - nxp,imx7d
  - meas,ms5611
  - st,st_sensors
* Where available (or easy to introduce) use the scan_type.* values
  in place of a second copy for read_raw and similar paths.
  - adi,ad7266
  - bosch,bma220
  - fsl,mac3110
  - fsl,mma7455
  - fsl,mpl3115
  - kionix,kcjk-1013
  - sensortek,stk8ba50
  - sensortek,stk8312
  - ti,adc12138
  - ti,ads1015
  - vti,sca3000
  - xilinx,xadc-core
* Switch drives over to generic firmware properties including appropriate
  header changes to avoid including of.h
  - Various DACs had false CONFIG_OF dependencies.
  - dpot-dac
  - envelope-detector
  - adi,ad5755
  - adi,ad5758
  - capella,cm3605
  - maxim,max9611
  - microchip,mcp41010
  - microchip,mcp3911
  - ti,adc12138
* Trivial clang warning fixes for W=1 warnings.

Driver specific cleanup and minor fixes
* adi,ad7606
  - Comment fixes.
* ams,ad3935
  - Drop pointless cast to the same type.
* atmel,at91-sama5d2
  - Fix wrong cast of iio_dev->dev to platform_device that happened to
    be harmless.
* fsl,mma7660
  - Stop i2c remove() function returning an error code. Part of a rework
    to eventually stop returning anything from these.
* fsl,mma8452
  - Use correct type for local irqreturn_t.
* nxp,imx8mq
  - Maintainer email address update.
* nxp,lpc18xx_adc
  - Ensure clk_prepare_enable() called before clk_get_rate().
  - Switch of.h for mod_devicetable.h to reflect no of specific functions,
    just the id table.
* renesas,rzg2l
  - Drop a dev_err() that just duplicates error printed in platform_get_irq()
* sgx,vz89x
  - Drop pointless cast.
* st,lsm6dsx
  - Make it possible to disable the sensorhub from DT to avoid a corner
    case where the address of a slave device many be accidentally modified.
* st,stm32-adc
  - Stop leaking an of_node in an error path.
* st,stmp2
   - Avoid wrong sized type for bit field which could result in
     over-reading (harmless). Precursor to enabling -Warray-bounds.
* ti,adc081c
  - Put back some ACPI support for non standards compliant ADC081C
    ID because it is known to be in the wild on some Aaeon boards.
* ti,ads8688
  - Cleanup redundant local ret variable assignment.
* ti,ina2xx-adc
  - Use helper macro kthread_run() to replace some boilerplate.
  - Avoid double reference counting.
  - Drop pointless cast.
* xilinx,xadc
  - Make the IRQ optional as not always wired to the host system.

* tag 'iio-for-5.17a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (103 commits)
  iio: adc: ti-adc081c: Partial revert of removal of ACPI IDs
  iio:addac:ad74413r: Fix uninitialized ret in a path that won't be hit.
  MAINTAINERS: Add maintainer for xilinx-ams
  dt-bindings: iio: adc: Add Xilinx AMS binding documentation
  iio: adc: Add Xilinx AMS driver
  device property: Add fwnode_iomap()
  iio:accel:kxcjk-1013: Mark struct __maybe_unused to avoid warning.
  iio:accel:bmc150: Mark structure __maybe_unused as only needed with for pm ops.
  iio:dummy: Drop set but unused variable len.
  iio:magn:ak8975: Suppress clang W=1 warning about pointer to enum conversion.
  iio:imu:inv_mpu6050: Suppress clang W=1 warning about pointer to enum conversion.
  iio:imu:inv_icm42600: Suppress clang W=1 warning about pointer to enum conversion.
  iio:dac:mcp4725: Suppress clang W=1 warning about pointer to enum conversion.
  iio:amplifiers:hmc425a: Suppress clang W=1 warning about pointer to enum conversion.
  iio:adc:ti-ads1015: Suppress clang W=1 warning about pointer to enum conversion.
  iio:adc:rcar: Suppress clang W=1 warning about pointer to enum conversion.
  iio:adc:ina2xx-adc: Suppress clang W=1 warning about pointer to enum conversion.
  iio:accel:bma180: Suppress clang W=1 warning about pointer to enum conversion.
  drivers:iio:dac: Add AD3552R driver support
  dt-bindings: iio: dac: Add adi,ad3552r.yaml
  ...

Unfortuanately a non standards compliant ACPI ID is known to be
in the wild on some AAEON boards.

Partly revert the removal of these IDs so that ADC081C will again
work + add a comment to that affect for future reference.

Whilst here use generic firmware properties rather than the ACPI
specific handling previously found in this driver.
Reported-by: Kunyang Fan <Kunyang_Fan@aaeon.com.tw>
Fixes: c458b7ca ("iio:adc:ti-adc081c: Drop ACPI ids that seem very unlikely to be official.")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Kunyang Fan <Kunyang_Fan@aaeon.com.tw> #UP-extremei11
Link: https://lore.kernel.org/r/20211205172728.2826512-1-jic23@kernel.org
Cc: <Stable@vger.kernel.org>

I don't believe it's possible to hit this, because we drop
out of __iio_update_buffers() earlier in the event of an empty
list.  However, that is not visible to the compiler so lets
return an error if we do hit the loop with an empty bitmask.

Fixes: 5d97d9e9 ("iio: addac: ad74413r: fix off by one in ad74413r_parse_channel_config()")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Cosmin Tanislav <cosmin.tanislav@analog.com>
Link: https://lore.kernel.org/r/20211220164726.3136307-1-jic23@kernel.org

Add maintaner entry for xilinx-ams driver.
Signed-off-by: Anand Ashok Dumbre <anand.ashok.dumbre@xilinx.com>
Link: https://lore.kernel.org/r/20211203212358.31444-6-anand.ashok.dumbre@xilinx.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Xilinx AMS have several ADC channels that can be used for measurement of
different voltages and temperatures. Document the same in the bindings.
Signed-off-by: Anand Ashok Dumbre <anand.ashok.dumbre@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211203212358.31444-5-anand.ashok.dumbre@xilinx.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The AMS includes an ADC as well as on-chip sensors that can be used to
sample external voltages and monitor on-die operating conditions, such
as temperature and supply voltage levels. The AMS has two SYSMON blocks.
PL-SYSMON block is capable of monitoring off chip voltage and
temperature.

PL-SYSMON block has DRP, JTAG and I2C interface to enable monitoring
from an external master. Out of these interfaces currently only DRP is
supported. Other block PS-SYSMON is memory mapped to PS.

The AMS can use internal channels to monitor voltage and temperature as
well as one primary and up to 16 auxiliary channels for measuring
external voltages.

The voltage and temperature monitoring channels also have event capability
which allows to generate an interrupt when their value falls below or
raises above a set threshold.
Co-developed-by: Manish Narani <manish.narani@xilinx.com>
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Signed-off-by: Anand Ashok Dumbre <anand.ashok.dumbre@xilinx.com>
Link: https://lore.kernel.org/r/20211203212358.31444-4-anand.ashok.dumbre@xilinx.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This patch introduces a new helper routine - fwnode_iomap(), which
allows to map the memory mapped IO for a given device node.

This implementation does not cover the ACPI case and may be expanded
in the future. The main purpose here is to be able to develop resource
provider agnostic drivers.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Anand Ashok Dumbre <anand.ashok.dumbre@xilinx.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20211203212358.31444-2-anand.ashok.dumbre@xilinx.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This structure is only used in PM ops, so may not be used depending
on build configuration.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20211128172445.2616166-13-jic23@kernel.org

If CONFIG_PM not set then clang warns this structure is unused.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20211128172445.2616166-12-jic23@kernel.org

Not sure what the thinking was here, as lost to history, but the
variable is clearly not used so get rid of it.

Warning seen with clang W=1 tests (may be present with other compilers
and build options).
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20211128172445.2616166-11-jic23@kernel.org

Cast to a uintptr_t rather than directly to the enum.

As per the discussion in below linked media patch.

Link: https://lore.kernel.org/linux-media/CAK8P3a2ez6nEw4d+Mqa3XXAz0RFTZHunqqRj6sCt7Y_Eqqs0rw@mail.gmail.com/Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Cc: Jonathan Albrieux <jonathan.albrieux@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20211128172445.2616166-10-jic23@kernel.org

Cast to a uintptr_t rather than directly to the enum.

As per the discussion in below linked media patch.

Link: https://lore.kernel.org/linux-media/CAK8P3a2ez6nEw4d+Mqa3XXAz0RFTZHunqqRj6sCt7Y_Eqqs0rw@mail.gmail.com/Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Cc: Baptiste Mansuy <bmansuy@invensense.com>
Cc: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20211128172445.2616166-9-jic23@kernel.org

Cast to a uintptr_t rather than directly to the enum.

As per the discussion in below linked media patch.

Link: https://lore.kernel.org/linux-media/CAK8P3a2ez6nEw4d+Mqa3XXAz0RFTZHunqqRj6sCt7Y_Eqqs0rw@mail.gmail.com/Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Cc: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20211128172445.2616166-8-jic23@kernel.org

Cast to a uintptr_t rather than directly to the enum.

As per the discussion in below linked media patch.

Link: https://lore.kernel.org/linux-media/CAK8P3a2ez6nEw4d+Mqa3XXAz0RFTZHunqqRj6sCt7Y_Eqqs0rw@mail.gmail.com/Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20211128172445.2616166-7-jic23@kernel.org

Cast to a uintptr_t rather than directly to the enum.

As per the discussion in below linked media patch.

Link: https://lore.kernel.org/linux-media/CAK8P3a2ez6nEw4d+Mqa3XXAz0RFTZHunqqRj6sCt7Y_Eqqs0rw@mail.gmail.com/Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20211128172445.2616166-6-jic23@kernel.org