- 22 Jul, 2021 35 commits
-
-
Bhaskar Chowdhury authored
s/miror/mirror/ Link: https://lore.kernel.org/linux-media/20210324135642.30054-1-unixbhaskar@gmail.comSigned-off-by:
Bhaskar Chowdhury <unixbhaskar@gmail.com> Acked-by:
Randy Dunlap <rdunlap@infradead.org> Signed-off-by:
Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
-
Ricardo Ribalda authored
Trivial fix. Link: https://lore.kernel.org/linux-media/20210318202223.164873-2-ribalda@chromium.orgSigned-off-by:
Ricardo Ribalda <ribalda@chromium.org> Signed-off-by:
-
Philipp Zabel authored
The frame memory control register value is currently determined before userspace selects the final capture format and never corrected. Update ctx->frame_mem_ctrl in __coda_start_decoding() to fix decoding into YUV420 or YVU420 capture buffers. Reported-by:
Andrej Picej <andrej.picej@norik.com> Fixes: 497e6b85 ("media: coda: add sequence initialization work") Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
-
Tom Rix authored
cal->ctx[i] is allocated with this loop for (i = 0; i < cal->data->num_csi2_phy; ++i) { and accessed in the error handler and else where with this loop for (i = 0; i < cal->num_contexts; i++) Because the first loop contains a continue statement before cal->num_contexts is incremented, using i as the indexer will leave gaps in the cal->ctx[]. So use cal->num_contexts as the indexer. Fixes: 75e7e58b ("media: ti-vpe: cal: support 8 DMA contexts") Signed-off-by:Tom Rix <trix@redhat.com> Signed-off-by:
-
Dan Carpenter authored
There are a few bugs in this code. 1) No checks for whether dma_alloc_attrs() or __get_free_pages() failed. 2) If video_register_device() fails it doesn't clean up the dma attrs or the free pages. 3) The video_device_release() function frees "vfd" which leads to a use after free on the next line. The call to video_unregister_device() is not required so I have just removed that. Fixes: f7e7b48e ("[media] rockchip/rga: v4l2 m2m support") Reported-by:
Dongliang Mu <mudongliangabcd@gmail.com> Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Evgeny Novikov authored
stm32_cec_probe() did not unprepare clocks on error handling paths. The patch fixes that. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Evgeny Novikov <novikov@ispras.ru> Signed-off-by:
-
Pavel Skripkin authored
My local syzbot instance hit memory leak in usb_set_configuration(). The problem was in unputted usb interface. In case of errors after usb_get_intf() the reference should be putted to correclty free memory allocated for this interface. Fixes: ec16dae5 ("V4L/DVB (7019): V4L: add support for Syntek DC1125 webcams") Cc: stable@vger.kernel.org Signed-off-by:
Pavel Skripkin <paskripkin@gmail.com> Signed-off-by:
-
Hans Verkuil authored
The description of adap_enable was out-of-date. Improve it so that it corresponds to what really happens. Signed-off-by:
-
Dafna Hirschfeld authored
Initializing the dma addresses of the capture buffers can move to the 'buf_init' callback, since it is enough to do it once for each buffer and not every time it is queued. Signed-off-by:
Dafna Hirschfeld <dafna.hirschfeld@collabora.com> Signed-off-by:
-
Dafna Hirschfeld authored
The virtual address can be accessed using vb2_plane_vaddr therefore there is no need to save it in an extra field in 'rkisp1_buffer'. Remove it. Signed-off-by:
Ezequiel Garcia <ezequiel@collabora.com> Signed-off-by:
-
Dan Carpenter authored
The v4l2_subdev_alloc_state() function returns error pointers, it doesn't return NULL. Fixes: 0d346d2a ("media: v4l2-subdev: add subdev-wide state struct") Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
-
Pavel Skripkin authored
In go7007_alloc() kzalloc() is used for struct go7007 allocation. It means that there is no need in zeroing any members, because kzalloc will take care of it. Removing these reduntant initialization steps increases execution speed a lot: Before: + 86.802 us | go7007_alloc(); After: + 29.595 us | go7007_alloc(); Fixes: 866b8695 ("Staging: add the go7007 video driver") Signed-off-by:
-
Pavel Skripkin authored
In commit 13764128 ("go7007: add sanity checking for endpoints") endpoint sanity check was introduced, but if check fails it simply returns with leaked pointers. Cutted log from my local syzbot instance: BUG: memory leak unreferenced object 0xffff8880209f0000 (size 8192): comm "kworker/0:4", pid 4916, jiffies 4295263583 (age 29.310s) hex dump (first 32 bytes): 30 b0 27 22 80 88 ff ff 75 73 62 2d 64 75 6d 6d 0.'"....usb-dumm 79 5f 68 63 64 2e 33 2d 31 00 00 00 00 00 00 00 y_hcd.3-1....... backtrace: [<ffffffff860ca856>] kmalloc include/linux/slab.h:556 [inline] [<ffffffff860ca856>] kzalloc include/linux/slab.h:686 [inline] [<ffffffff860ca856>] go7007_alloc+0x46/0xb40 drivers/media/usb/go7007/go7007-driver.c:696 [<ffffffff860de74e>] go7007_usb_probe+0x13e/0x2200 drivers/media/usb/go7007/go7007-usb.c:1114 [<ffffffff854a5f74>] usb_probe_interface+0x314/0x7f0 drivers/usb/core/driver.c:396 [<ffffffff845a7151>] really_probe+0x291/0xf60 drivers/base/dd.c:576 BUG: memory leak unreferenced object 0xffff88801e2f2800 (size 512): comm "kworker/0:4", pid 4916, jiffies 4295263583 (age 29.310s) hex dump (first 32 bytes): 00 87 40 8a ff ff ff ff 00 00 00 00 00 00 00 00 ..@............. 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<ffffffff860de794>] kmalloc include/linux/slab.h:556 [inline] [<ffffffff860de794>] kzalloc include/linux/slab.h:686 [inline] [<ffffffff860de794>] go7007_usb_probe+0x184/0x2200 drivers/media/usb/go7007/go7007-usb.c:1118 [<ffffffff854a5f74>] usb_probe_interface+0x314/0x7f0 drivers/usb/core/driver.c:396 [<ffffffff845a7151>] really_probe+0x291/0xf60 drivers/base/dd.c:576 Fixes: 13764128 ("go7007: add sanity checking for endpoints") Signed-off-by:
-
Matthew Michilot authored
Captured video would be out of sync when using the adv7280 with the BT.656-4 protocol. Certain registers (0x04, 0x31, 0xE6) had to be configured properly to ensure BT.656-4 compatibility. An error in the adv7280 reference manual suggested that EAV/SAV mode was enabled by default, however upon inspecting register 0x31, it was determined to be disabled by default. [fabio: Introduce "adv,force-bt656-4" to not affect the existing users] [hverkuil: fix a small checkpatch alignment warning] Signed-off-by:
Matthew Michilot <matthew.michilot@gmail.com> Reviewed-by:
Tim Harvey <tharvey@gateworks.com> Signed-off-by:
Fabio Estevam <festevam@gmail.com> Tested-by:
-
Fabio Estevam authored
Captured NTSC video would be out of sync when using the adv7280 with the BT.656-4 protocol. Certain registers (0x04, 0x31, 0xE6) need to be configured properly to ensure BT.656-4 compatibility. Introduce the 'adv,force-bt656-4' property to allow the ADV7280 behavior to be consistent with the ADV7180, where BT.656-4 timing is used by default. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Fabio Estevam authored
Improve the probe message by printing the chip ID version. Signed-off-by:
Frieder Schrempf <frieder.schrempf@kontron.de> Signed-off-by:
-
Frieder Schrempf authored
There is a reset input that can be controlled by GPIO. Let's add it to let the driver control it if required. [hverkuil: fix a small checkpatch alignment warning] Signed-off-by:
-
Fabio Estevam authored
Introduce the 'reset-gpios' property to describe the GPIO that connects to the ADV7180 reset pin. Signed-off-by:
-
Paul Kocialkowski authored
The Rockchip PX30 SoC has a Hantro VPU that features a decoder (VDPU2) and an encoder (VEPU2). Suggested-by:
Alex Bee <knaerzche@gmail.com> Signed-off-by:
Paul Kocialkowski <paul.kocialkowski@bootlin.com> Signed-off-by:
-
Paul Kocialkowski authored
The PX30 SoC includes both the VDPU2 and VEPU2 blocks which are similar to the RK3399 (Hantro G1/H1 with shuffled registers). Signed-off-by:
-
Ezequiel Garcia authored
Given H.264 support for VDPU2 was just added, let's enable it. For now, this is only enabled on platform that don't have an RKVDEC core, such as RK3328. Signed-off-by:
-
Jonas Karlman authored
Rockchip VDPU2 core is present on RK3328, RK3326/PX30, RK3399 and others. It's similar to Hantro G1, but it's not compatible with it. Signed-off-by:
Jonas Karlman <jonas@kwiboo.se> Signed-off-by:
-
Ezequiel Garcia authored
Add a hantro_h264_get_ref_nbr() helper function to get the reference picture numbers. This will be used by the Rockchip VDPU2 H.264 driver. This idea was originally proposed by Jonas Karlman in "[RFC 09/12] media: hantro: Refactor G1 H264 code" posted a while ago. Link: https://lore.kernel.org/linux-media/HE1PR06MB401165F2BA0AD8A634FDFAF2ACBF0@HE1PR06MB4011.eurprd06.prod.outlook.com/Signed-off-by:
-
Ezequiel Garcia authored
In order to reuse these bitmaps, move this process to struct hantro_h264_dec_hw_ctx. This will be used by the Rockchip VDPU2 H.264 driver. This idea was originally proposed by Jonas Karlman in "[RFC 08/12] media: hantro: Fix H264 decoding of field encoded content" which was posted a while ago. Link: https://lore.kernel.org/linux-media/HE1PR06MB4011EA39133818A85768B91FACBF0@HE1PR06MB4011.eurprd06.prod.outlook.com/Signed-off-by:
-
Ezequiel Garcia authored
Getting the next src/dst buffer is relatively expensive so avoid doing it multiple times. Signed-off-by:
-
Ezequiel Garcia authored
The hantro_variant.init() function is there for platforms to perform hardware-specific initialization, such as clock rate bumping. Not all platforms require it, so make it optional. Signed-off-by:
-
Ezequiel Garcia authored
When the VP8 decoders can't find a reference frame, the driver falls back to the current output frame. This will probably produce some undesirable results, leading to frame corruption, but shouldn't cause noisy warnings. Signed-off-by:
Nicolas Dufresne <nicolas.dufresne@collabora.com> Tested-by:
-
Dongliang Mu authored
In dvb_usb_i2c_init, if i2c_add_adapter fails, it only prints an error message, and then continues to set DVB_USB_STATE_I2C. This affects the logic of dvb_usb_i2c_exit, which leads to that, the deletion of i2c_adap even if the i2c_add_adapter fails. Fix this by returning at the failure of i2c_add_adapter and then move dvb_usb_i2c_exit out of the error handling code of dvb_usb_i2c_init. Fixes: 13a79f14 ("media: dvb-usb: Fix memory leak at error in dvb_usb_device_init()") Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
-
Dongliang Mu authored
If vp702x_usb_in_op fails, the mac address is not initialized. And vp702x_read_mac_addr does not handle this failure, which leads to the uninit-value in dvb_usb_adapter_dvb_init. Fix this by handling the failure of vp702x_usb_in_op. Fixes: 786baecf ("[media] dvb-usb: move it to drivers/media/usb/dvb-usb") Signed-off-by:
-
Dongliang Mu authored
If dibusb_read_eeprom_byte fails, the mac address is not initialized. And nova_t_read_mac_address does not handle this failure, which leads to the uninit-value in dvb_usb_adapter_dvb_init. Fix this by handling the failure of dibusb_read_eeprom_byte. Reported-by: syzbot+e27b4fd589762b0b9329@syzkaller.appspotmail.com Fixes: 786baecf ("[media] dvb-usb: move it to drivers/media/usb/dvb-usb") Signed-off-by:
-
Sean Young authored
The s_learning_mode() function is called in response to the ioctl LIRC_SET_WIDEBAND_RECEIVER, so rename it to s_wideband_receiver(). Learning mode is when both the wideband receiver is turned on and carrier reports are enabled. Signed-off-by:
-
Sean Young authored
Any timeout larger than LIRC_VALUE_MASK cannot work for the lirc uapi. LIRC_VALUE_MASK is about 16 seconds which is more than enough. Signed-off-by:
-
Sean Young authored
When carrier reports are enabled, send them over loopback. Signed-off-by:
-
Sean Young authored
Make use of dynamic debug. Signed-off-by:
-
Sean Young authored
The LIRC_SET_TRANSMITTER_MASK ioctl should return the number of emitters if an invalid list was set. Cc: stable@vger.kernel.org Signed-off-by:
-
- 12 Jul, 2021 5 commits
-
-
Uwe Kleine-König authored
The Logilink VG0022A DVB-T2 stick has these three devices. So to enable support for this stick in the presence of MEDIA_SUBDRV_AUTOSELECT, let DVB_USB_AF9035 select the two other drivers. Signed-off-by:
Uwe Kleine-König <uwe@kleine-koenig.org> Signed-off-by:
-
Uwe Kleine-König authored
If a sub device doesn't immediately bind after it was added, emit an error indication to the kernel log to help debugging. This happens for example if the needed driver isn't available at all. Signed-off-by:
-
lijian authored
break is not useful after a goto, so delete 'break' after 'goto'. Signed-off-by:
lijian <lijian@yulong.com> Signed-off-by:
-
Christophe JAILLET authored
If an error occurs after a successful 'regulator_enable()' call, 'regulator_disable()' must be called. Fix the error handling path of the probe accordingly. Fixes: cb496cd4 ("media: cxd2880-spi: Add optional vcc regulator") Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
-
lijian authored
deleted the repeated word 'the' in the comments. Signed-off-by:
-
