- 27 Apr, 2017 35 commits
-
-
Boris Brezillon authored
These new helpers + macro definitions are meant to replace the old ones which are unpractical to use. Note that the macros and function prefixes have been intentionally changed to ATMEL_[H]SMC_XX and atmel_[h]smc_ to reflect the fact that this IP is also embedded in avr32 SoCs (and not only in at91 ones). Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Belen Sarabia authored
devm_ioremap_resource does checks on the resource. No need to duplicate this in the driver. Signed-off-by: Belén Sarabia <belensarabia@gmail.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Keerthy authored
POWERHOLD signal has higher priority over the DEV_ON bit. So power off will not happen if the POWERHOLD is held high. Hence reset the MUX to GPIO_7 mode to release the POWERHOLD and the DEV_ON bit to take effect to power off the PMIC. PMIC Power off happens in dire situations like thermal shutdown so irrespective of the POWERHOLD setting go ahead and turn off the powerhold. Currently poweroff is broken on boards that have powerhold enabled. This fixes poweroff on those boards. Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Julia Cartwright authored
The tc6393xb mfd driver currently implements an irq_chip for handling interrupts; due to how irq_chip handling is done, it's necessary for the irq_chip methods to be invoked from hardirq context, even on a a real-time kernel. Because the spinlock_t type becomes a "sleeping" spinlock w/ RT kernels, it is not suitable to be used with irq_chips. A quick audit of the operations under the lock reveal that they do only minimal, bounded work, and are therefore safe to do under a raw spinlock. Signed-off-by: Julia Cartwright <julia@ni.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Julia Cartwright authored
The t7l66xb mfd driver currently implements an irq_chip for handling interrupts; due to how irq_chip handling is done, it's necessary for the irq_chip methods to be invoked from hardirq context, even on a a real-time kernel. Because the spinlock_t type becomes a "sleeping" spinlock w/ RT kernels, it is not suitable to be used with irq_chips. A quick audit of the operations under the lock reveal that they do only minimal, bounded work, and are therefore safe to do under a raw spinlock. Signed-off-by: Julia Cartwright <julia@ni.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Julia Cartwright authored
The asic3 mfd driver currently implements an irq_chip for handling interrupts; due to how irq_chip handling is done, it's necessary for the irq_chip methods to be invoked from hardirq context, even on a a real-time kernel. Because the spinlock_t type becomes a "sleeping" spinlock w/ RT kernels, it is not suitable to be used with irq_chips. A quick audit of the operations under the lock reveal that they do only minimal, bounded work, and are therefore safe to do under a raw spinlock. Signed-off-by: Julia Cartwright <julia@ni.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Andy Shevchenko authored
For better understanding of relationship between headers and modules rename: intel_bxtwc.h -> intel_soc_pmic_bxtwc.h While here, remove file name from the file itself. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Andy Shevchenko authored
There is no need to include intel_soc_pmic.h into header which doesn't require it. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Charles Keepax authored
Currently, we specify the timeout in terms of the number of polls but it is more clear from a user of the functions perspective to specify the timeout directly in milliseconds, as such update the function to these new semantics. Additionally, arizona_poll_reg essentially hard-codes regmap_read_poll_timeout, update the implementation to use regmap_read_poll_timeout. We still keep arizona_poll_reg around as regmap_read_poll_timeout is a macro so rather than expand this for each caller keep it wrapped in arizona_poll_reg. Whilst we are doing this make the timeouts a little more generous as the previous system had a bit more slack as it was done as a delay per iteration of the loop whereas regmap_read_poll_timeout compares ktime's. Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Charles Keepax authored
Register addresses are normally displayed in hex throughout the Arizona driver. Update the arizona_poll_reg function to follow this convention. Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Charles Keepax authored
arizona_poll_reg already returns ETIMEDOUT if we don't see the expected register changes before the time out, so remove pointless local setting of ETIMEDOUT. Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Joe Perches authored
To enable eventual removal of pr_warning This makes pr_warn use consistent for drivers/mfd Prior to this patch, there were 4 uses of pr_warning and 9 uses of pr_warn in drivers/mfd Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Sean Wang authored
Align the placement as which the mfd_cell of LED is defined as the other members done on the structure. Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Sean Wang authored
This patch adds description for LED as the sub-module on MT6397/MT6323 multifunction device. Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Quentin Schulz authored
The CHRG_CTRL1 and CHRG_CTRL2 registers are made for controlling different battery charging settings such as the constant current charge value. The AXP22X also have a third register CHRG_CTRL3 which has settings for battery charging too. This adds the CHRG_CTRL1, CHRG_CTRL2 and CHRG_CTRL3 registers to the list of writeable registers for AXP20X and AXP22X PMICs. Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Quentin Schulz authored
The X-Powers AXP20X and AXP22X PMICs expose the status of AC power supply. This adds the AC power supply driver to the MFD cells of the AXP22X PMICs. Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-By: Sebastian Reichel <sre@kernel.org> Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Quentin Schulz authored
This adds the AXP20X/AXP22x ADCs driver to the mfd cells of the AXP209, AXP221 and AXP223 MFD. Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Quentin Schulz authored
The registers 0x56 and 0x57 of AXP22X PMIC store the value of the internal temperature of the PMIC. This patch modifies the name of these registers from AXP22X_PMIC_ADC_H/L to AXP22X_PMIC_TEMP_H/L so their purpose is clearer. Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com> Acked-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Andrew F. Davis authored
The SPI interface is mostly a copy/paste from the I2C interface with some minor renaming for consistency. "Client" is an I2C specific term that was left in the SPI remove path, rename this here. Signed-off-by: Andrew F. Davis <afd@ti.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Thor Thayer authored
This patch adds documentation for the Altera A10-SR Reset Controller DT bindings. Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Thor Thayer authored
Add Peripheral PHY Reset Controller to the Arria10 Development Kit System Resource Chip's MFD. Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Andy Shevchenko authored
After commit 028af594 ("mfd: intel-lpss: Pass SDA hold time to I2C host controller driver") the driver still has a non-used variable. Remove it here. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Doug Anderson authored
This is a sucky change to bump up the time we'll wait for the EC. Why is it sucky? If 200ms for a transfer is a common thing it will have a massively bad impact on keyboard responsiveness. It still seems like a good idea to do this, though, because we have a gas gauge that claims that in an extreme case it could stretch the i2c clock for 144ms. It's not a common case so it shouldn't affect responsiveness, but it can happen. It's much better to have a single slow keyboard response than to start returning errors when we don't have to. In newer EC designs we should probably implement a virtual battery to respond to the kernel to insulate the kernel from these types of issues. Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Milo Kim authored
TI LMU (Lighting Management Unit) driver supports lighting devices below. LM3532, LM3631, LM3632, LM3633, LM3695 and LM3697. LMU devices have common features. - I2C interface for accessing device registers - Hardware enable pin control - Backlight brightness control - Notifier for hardware fault monitoring - Regulators for LCD display bias It contains fault monitor, backlight, LED and regulator driver. LMU fault monitor ----------------- LM3633 and LM3697 provide hardware monitoring feature. It enables open or short circuit detection. After monitoring is done, each device should be re-initialized. Notifier is used for this case. Separate patch for 'ti-lmu-fault-monitor' will be sent later. Backlight --------- It's handled by TI LMU backlight consolidated driver and chip dependent data. Separate patchset will be sent later. LED indicator ------------- LM3633 has 6 indicator LEDs. Programmable dimming pattern is also supported. Separate patch for 'leds-lm3633' will be sent later. Regulator --------- LM3631 has 5 regulators for the display bias. LM3632 supports 3 regulators. One consolidated driver enables it. The lm363x regulator driver is already upstreamed. Signed-off-by: Milo Kim <milo.kim@ti.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Milo Kim authored
This patch describes overall binding for TI LMU MFD devices. Signed-off-by: Milo Kim <milo.kim@ti.com> Acked-by: Rob Herring <robh+dt@kernel.org> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Rask Ingemann Lambertsen authored
commit b101829a029a ("mfd: axp20x: Fix AXP806 access errors on cold boot") was intended to fix the case where a board uses an AXP806 in slave mode, but the boot loader leaves it in master mode for lack of AXP806 support. But now the driver breaks on boards where the PMIC is operating in master mode. This patch lets the driver use the new device tree property "xpowers,master-mode" to set the correct operating mode for the board. Fixes: 8824ee85 ("mfd: axp20x: Add support for AXP806 PMIC") Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Rask Ingemann Lambertsen authored
commit b101829a029a ("mfd: axp20x: Fix AXP806 access errors on cold boot") was intended to fix the case where a board uses an AXP806 in slave mode, but the boot loader leaves it in master mode for lack of AXP806 support. But now the driver breaks on boards where the PMIC is operating in master mode. To let the device tree describe which mode of operation is needed, this patch introduces a new property "xpowers,master-mode". Fixes: 204ae296 ("mfd: axp20x: Add bindings for AXP806 PMIC") Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk> Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Andy Shevchenko authored
Since commit 845c8770 ("i2c / ACPI: Assign IRQ for devices that have GpioInt automatically") I2C core assigns interrupt line to I2C slave devices with regarding to GpioInt() resources. There is no need to repeat this in the driver. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Fabrice Gasnier authored
STM32 timers register bank size is 0x400. Fix regmap max_register. Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Borislav Petkov authored
It is a debugging statement so make it be issued only then. No functionality change. Signed-off-by: Borislav Petkov <bp@suse.de> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Adam Ford authored
At least two different omap3630/3730 boards booting from MMC1 fail to reboot if the "ti,twl4030-power-idle-osc-off" or "ti,twl4030-power-idle" compatible flags are set. This patch will keep the vmmc1 powered up during reboot allowing the bootloader to load. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Fabrice Gasnier authored
Add missing of_platform_depopulate() upon driver removal. Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Priyalee Kushwaha authored
This patches adds the first minimal support to the upstream Linux tree. Signed-off-by: Priyalee Kushwaha <priyalee.kushwaha@intel.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Archana Patni authored
This patch installs an ACPI GPE handler for LID0 ACPI device to indicate ACPI core that this GPE should stay enabled for lid to work in suspend to idle path. Signed-off-by: Archana Patni <archana.patni@intel.com> Signed-off-by: Thierry Escande <thierry.escande@collabora.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Lee Jones authored
Merge branches 'ib-mfd-gpio-4.12', 'ib-mfd-iio-input-4.12', 'ib-mfd-input-4.12', 'ib-mfd-leds-4.12', 'ib-mfd-phy-4.12' and 'ib-mfd-pinctrl-samsung-4.12' into ibs-for-mfd-merged
-
- 11 Apr, 2017 2 commits
-
-
Sebastian Reichel authored
Motorola CPCAP is a PMIC found in multiple smartphones. This driver adds support for the power/on button and has been tested in Droid 4. Acked-by: Rob Herring <robh@kernel.org> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Sebastian Reichel authored
CPCAP can sense if IRQ is currently set or not. This functionality is required for a few subdevices, such as the power button and usb phy modules. Signed-off-by: Sebastian Reichel <sre@kernel.org> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
- 28 Mar, 2017 1 commit
-
-
Sebastian Reichel authored
This fixes compilation for files, that try to include the cpcap header in alphabetically sorted #include lists. Acked-by: Pavel Machek <pavel@ucw.cz> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
- 23 Mar, 2017 2 commits
-
-
Marek Szyprowski authored
This patch adds support for retention control for Exynos5433 SoCs. Three groups of pins has been defined for retention control: common shared group for ALIVE, CPIF, eSE, FINGER, IMEM, NFC, PERIC, TOUCH pin banks and separate control for FSYS and AUD pin banks, for which PMU retention registers match whole banks. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
-
Marek Szyprowski authored
When pin controller device is a part of power domain, there is no guarantee that the power domain was not turned off and then on during boot process before probing of the pin control driver. If it happened, then pin control driver should ensure that pad retention is turned off during its probe call. Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
-