Convert the Altera Triple Speed Ethernet Controller to phylink.
This controller supports MII, GMII and RGMII with its MAC, and
SGMII + 1000BaseX through a small embedded PCS.

The PCS itself has a register set very similar to what is found in a
typical 802.3 ethernet PHY, but this register set memory-mapped instead
of lying on an mdio bus.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Altera Triple Speed Ethernet has a SGMII/1000BaseC PCS that can be
integrated in several ways. It can either be part of the TSE MAC's
address space, accessed through 32 bits accesses on the mapped mdio
device 0, or through a dedicated 16 bits register set.

This driver allows using the TSE PCS outside of altera TSE's driver,
since it can be used standalone by other MACs.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make the driver code cleaner through a strictly cosmetic change, using
he reverse xmas tree variable declaration ordering.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert the bindings for the Altera Triple-Speed Ethernet to yaml.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-next-2022-09-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next

Johannes Berg says:

====================
drivers
 - rtw89: large update across the map, e.g. coex, pci(e), etc.
 - ath9k: uninit memory read fix
 - ath10k: small peer map fix and a WCN3990 device fix
 - wfx: underflow

stack
 - the "change MAC address while IFF_UP" change from James
   we discussed
 - more MLO work, including a set of fixes for the previous
   code, now that we have more code we can exercise it more
 - prevent some features with MLO that aren't ready yet
   (AP_VLAN and 4-address connections)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In netlink RX, now that we can actually have multiple
channel contexts for MLO, things don't work well as we
only keep a single pointer, and then on link switching
we might NULL it, and hit the return if the channel is
NULL.

However, we already use mac80211_hwsim_tx_iter() which
deals with all this, so remove the test and adjust the
remaining code a bit.

This then means we no longer use the chanctx pointer,
so remove it as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Currently, other paths calling drv_sta_state() hold the mutex
and therefore drivers can assume that, and look at links with
that protection. Fix that for the reconfig path as well; to
do it more easily use ieee80211_reconfig_stations() for the
AP/AP_VLAN station reconfig as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add an MLD address attribute to BSS entries that the interface
is currently associated with to help userspace figure out what's
going on.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Refactor the code to apply QoS settings to the driver so
we can call it on link switch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Catch the bugs fixed in mac80211 by the previous commits
and warn if an invalid address is added (or removed).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When we stop a not-yet-started scan, we erroneously call
into the driver, causing a sequence of sw_scan_start()
followed by sw_scan_complete() twice. This will cause a
warning in hwsim with next in line commit that validates
the address passed to wmediumd/virtio. Fix this by doing
the calls only if we were actually scanning.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Right now, we assign the link address only after we add
the link to the driver, which is quite obviously wrong.
It happens to work in many cases because it gets updated
immediately, and then link_conf updates may update it,
but it's clearly not really right.

Set the link address during ieee80211_mgd_setup_link()
so it's set before telling the driver about the link.

Fixes: 81151ce4 ("wifi: mac80211: support MLO authentication/association with one link")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

We probably should've done that originally, we already have
about 300 lines of code there, and will add more. Move all
the link code we wrote to a new file.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Refactor some common RX functionality between the netlink
and non-netlink paths, adding the special hwsim TLV (if
compiled) also in the netlink path.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Just as an additional check that mac80211 isn't doing
anything strange, add a check of the STA magic (which
gets assigned when the station is added, and cleared
when the station is removed).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

We don't need the sdata argument, and it doesn't make any
sense for a direct conversion from one value to another,
so just remove the argument
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Now that we have proper multicast TX in mac80211, there's
no longer a need to fake something here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Return value from rdev_set_mcast_rate() directly instead of
taking this in another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Jinpeng Cui <cui.jinpeng2@zte.com.cn>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Adds support in mac80211 for NL80211_EXT_FEATURE_POWERED_ADDR_CHANGE.
The motivation behind this functionality is to fix limitations of
address randomization on frequencies which are disallowed in world
roaming.

The way things work now, if a client wants to randomize their address
per-connection it must power down the device, change the MAC, and
power back up. Here lies a problem since powering down the device
may result in frequencies being disabled (until the regdom is set).
If the desired BSS is on one such frequency the client is unable to
connect once the phy is powered again.

For mac80211 based devices changing the MAC while powered is possible
but currently disallowed (-EBUSY). This patch adds some logic to
allow a MAC change while powered by removing the interface, changing
the MAC, and adding it again. mac80211 will advertise support for
this feature so userspace can determine the best course of action e.g.
disallow address randomization on certain frequencies if not
supported.

There are certain limitations put on this which simplify the logic:
 - No active connection
 - No offchannel work, including scanning.
Signed-off-by: James Prestwood <prestwoj@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add a new extended feature bit signifying that the wireless hardware
supports changing the MAC address while the underlying net_device is
powered. Note that this has a different meaning from
IFF_LIVE_ADDR_CHANGE as additional restrictions might be imposed by
the hardware, such as:

 - No connection is active on this interface, carrier is off
 - No scan is in progress
 - No offchannel operations are in progress
Signed-off-by: James Prestwood <prestwoj@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

We haven't tried this yet, and it's not very likely to
work well right now, so for now disable 4-addr use on
interfaces that are MLDs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20220902161143.f2e4cc2efaa1.I5924e8fb44a2d098b676f5711b36bbc1b1bd68e2@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>

Do not allow VLANs to be added to AP interfaces that are
MLDs, this isn't going to work because the link structs
aren't propagated to the VLAN interfaces yet.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20220902161144.8c88531146e9.If2ef9a3b138d4f16ed2fda91c852da156bdf5e4d@changeidSigned-off-by: Johannes Berg <johannes.berg@intel.com>

Zhengchao Shao says:

====================
net: sched: remove redundant resource cleanup when init() fails

qdisc_create() calls .init() to initialize qdisc. If the initialization
fails, qdisc_create() will call .destroy() to release resources.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If htb_init() fails, qdisc_create() invokes htb_destroy() to clear
resources. Therefore, remove redundant resource cleanup in htb_init().
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If fq_codel_init() fails, qdisc_create() invokes fq_codel_destroy() to
clear resources. Therefore, remove redundant resource cleanup in
fq_codel_init().
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current driver support stop mode by calling machine api.
The patch add dts support to set GPR register for stop request.

imx8mq enter stop/exit stop mode by setting GPR bit, which can
be accessed by A core.
imx8qm enter stop/exit stop mode by calling IMX_SC ipc APIs that
communicate with M core ipc service, and the M core set the related
GPR bit at last.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Lenovo USB-C Travel Hub supports MAC passthrough.
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>

We now have a cleaner way to keep compatibility with user-space
(a.k.a. not breaking it) when we need to keep in place a one-element
array (for its use in user-space) together with a flexible-array
member (for its use in kernel-space) without making it hard to read
at the source level. This is through the use of the new
__DECLARE_FLEX_ARRAY() helper macro.

The size and memory layout of the structure is preserved after the
changes. See below.

Before changes:

$ pahole -C ip_msfilter net/ipv4/igmp.o
struct ip_msfilter {
	union {
		struct {
			__be32     imsf_multiaddr_aux;   /*     0     4 */
			__be32     imsf_interface_aux;   /*     4     4 */
			__u32      imsf_fmode_aux;       /*     8     4 */
			__u32      imsf_numsrc_aux;      /*    12     4 */
			__be32     imsf_slist[1];        /*    16     4 */
		};                                       /*     0    20 */
		struct {
			__be32     imsf_multiaddr;       /*     0     4 */
			__be32     imsf_interface;       /*     4     4 */
			__u32      imsf_fmode;           /*     8     4 */
			__u32      imsf_numsrc;          /*    12     4 */
			__be32     imsf_slist_flex[0];   /*    16     0 */
		};                                       /*     0    16 */
	};                                               /*     0    20 */

	/* size: 20, cachelines: 1, members: 1 */
	/* last cacheline: 20 bytes */
};

After changes:

$ pahole -C ip_msfilter net/ipv4/igmp.o
struct ip_msfilter {
	__be32                     imsf_multiaddr;       /*     0     4 */
	__be32                     imsf_interface;       /*     4     4 */
	__u32                      imsf_fmode;           /*     8     4 */
	__u32                      imsf_numsrc;          /*    12     4 */
	union {
		__be32             imsf_slist[1];        /*    16     4 */
		struct {
			struct {
			} __empty_imsf_slist_flex;       /*    16     0 */
			__be32     imsf_slist_flex[0];   /*    16     0 */
		};                                       /*    16     0 */
	};                                               /*    16     4 */

	/* size: 20, cachelines: 1, members: 5 */
	/* last cacheline: 20 bytes */
};

In the past, we had to duplicate the whole original structure within
a union, and update the names of all the members. Now, we just need to
declare the flexible-array member to be used in kernel-space through
the __DECLARE_FLEX_ARRAY() helper together with the one-element array,
within a union. This makes the source code more clean and easier to read.

Link: https://github.com/KSPP/linux/issues/193Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcf_qevent_parse_block_index() never returns a zero block_index.
Therefore, it is unnecessary to check the value of block_index in
tcf_qevent_init().
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Link: https://lore.kernel.org/r/20220901011617.14105-1-shaozhengchao@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Since Linux now supports CFI, it will be a good idea to fix mismatched
return type for implementation of hooks. Otherwise this might get
cought out by CFI and cause a panic.

ltq_etop_tx() would return either NETDEV_TX_BUSY or NETDEV_TX_OK, so
change the return type to netdev_tx_t directly.
Signed-off-by: GUO Zihua <guozihua@huawei.com>
Link: https://lore.kernel.org/r/20220902081521.59867-1-guozihua@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Since Linux now supports CFI, it will be a good idea to fix mismatched
return type for implementation of hooks. Otherwise this might get
cought out by CFI and cause a panic.

spl2sw_ethernet_start_xmit() would return either NETDEV_TX_BUSY or
NETDEV_TX_OK, so change the return type to netdev_tx_t directly.
Signed-off-by: GUO Zihua <guozihua@huawei.com>
Link: https://lore.kernel.org/r/20220902081550.60095-1-guozihua@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Since Linux now supports CFI, it will be a good idea to fix mismatched
return type for implementation of hooks. Otherwise this might get
cought out by CFI and cause a panic.

eth_xmit() would return either NETDEV_TX_BUSY or NETDEV_TX_OK, so
change the return type to netdev_tx_t directly.
Signed-off-by: GUO Zihua <guozihua@huawei.com>
Link: https://lore.kernel.org/r/20220902081612.60405-1-guozihua@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Since Linux now supports CFI, it will be a good idea to fix mismatched
return type for implementation of hooks. Otherwise this might get
cought out by CFI and cause a panic.

bcm4908_enet_start_xmit() would return either NETDEV_TX_BUSY or
NETDEV_TX_OK, so change the return type to netdev_tx_t directly.
Signed-off-by: GUO Zihua <guozihua@huawei.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220902075407.52358-1-guozihua@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When CONFIG_IEEE802154_NL802154_EXPERIMENTAL is disabled,
NL802154_CMD_DEL_SEC_LEVEL is undefined and results in a compilation
error:
net/ieee802154/nl802154.c:2503:19: error: 'NL802154_CMD_DEL_SEC_LEVEL' undeclared here (not in a function); did you mean 'NL802154_CMD_SET_CCA_ED_LEVEL'?
 2503 |  .resv_start_op = NL802154_CMD_DEL_SEC_LEVEL + 1,
      |                   ^~~~~~~~~~~~~~~~~~~~~~~~~~
      |                   NL802154_CMD_SET_CCA_ED_LEVEL

Unhide the experimental commands, having them defined in an enum
makes no difference.

Fixes: 9c5d03d3 ("genetlink: start to validate reserved header bytes")
Signed-off-by: Gal Pressman <gal@nvidia.com>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Tested-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Link: https://lore.kernel.org/r/20220902030620.2737091-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

All callers are now gone.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add some documentation for netdev_tx_sent_queue() and
netdev_tx_completed_queue()

Stating that netdev_tx_completed_queue() must be called once
per TX completion round is apparently not obvious for everybody.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alex Elder says:

====================
net: ipa: use IDs to track transaction state

This series is the first of three groups of changes that simplify
the way the IPA driver tracks the state of its transactions.

Each GSI channel has a fixed number of transactions allocated at
initialization time.  The number allocated matches the number of
TREs in the transfer ring associated with the channel.  This is
because the transfer ring limits the number of transfers that can
ever be underway, and in the worst case, each transaction represents
a single TRE.

Transactions go through various states during their lifetime.
Currently a set of lists keeps track of which transactions are in
each state.  Initially, all transactions are free.  An allocated
transaction is placed on the allocated list.  Once an allocated
transaction is committed, it is moved from the allocated to the
committed list.  When a committed transaction is sent to hardware
(via a doorbell) it is moved to the pending list.  When hardware
signals that some work has completed, transactions are moved to the
completed list.  Finally, when a completed transaction is polled
it's moved to the polled list before being removed when it becomes
free.

Changing a transaction's state thus normally involves manipulating
two lists, and to prevent corruption a spinlock is held while the
lists are updated.

Transactions move through their states in a well-defined sequence
though, and they do so strictly in order.  So transaction 0 is
always allocated before transaction 1; transaction 0 is always
committed before transaction 1; and so on, through completion,
polling, and becoming free.  Because of this, it's sufficient to
just keep track of which transaction is the first in each state.
The rest of the transactions in a given state can be derived from
the first transaction in an "adjacent" state.  As a result, we can
track the state of all transactions with a set of indexes, and can
update these without the need for a spinlock.

This first group of patches just defines the set of indexes that
will be used for this new way of tracking transaction state.  Two
more groups of patches will follow.  I've broken the 17 patches into
these three groups to facilitate review.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a transaction ID to track the first element in the transaction
array that has been polled.  Advance the ID when we are releasing a
transaction.

Temporarily add warnings that verify that the first polled
transaction tracked by the ID matches the first element on the
polled list, both when polling and freeing.

Remove the temporary warnings added by the previous commit.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a transaction ID field to track the first element in the
transaction array that has completed but has not yet been polled.

Advance the ID when we are processing a transaction in the NAPI
polling loop (where completed transactions become polled).

Temporarily add warnings that verify that the first completed
transaction tracked by the ID matches the first element on the
completed list, both when pending and completing.

Remove the temporary warnings added by the previous commit.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a transaction ID field to track the first element in the
transaction array that is pending (sent to hardware) but not yet
complete.  Advance the ID when a completion event for a channel
indicates that transactions have completed.

Temporarily add warnings that verify that the first pending
transaction tracked by the ID matches the first element on the
pending list, both when pending and completing, as well as when
resetting the channel.

Remove the temporary warnings added by the previous commit.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>