Don't allow everybody to write to mb0_id file.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The fdb_create() puts a new fdb into hash with only addr set. This is
not good, since there are callers, that search the hash w/o the lock
and access all the other its fields.

Applies to current netdev tree.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

While the RxFIFO interruption is masked for most 8168, nothing prevents
it to appear in the irq status word. This is no excuse to crash.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Ivan Vecera <ivecera@redhat.com>
Cc: Hayes <hayeswang@realtek.com>

Some experiment-based action to prevent my 8168 chipsets locking-up hard
in the irq handler under load (pktgen ~1Mpps). Apparently a reset is not
always mandatory (is it at all ?).

- RTL_GIGA_MAC_VER_12
- RTL_GIGA_MAC_VER_25
  Missed ~55% packets. Note:
  - this is an old SiS 965L motherboard
  - the 8168 chipset emits (lots of) control frames towards the sender

- RTL_GIGA_MAC_VER_26
  The chipset does not go into a frenzy of mac control pause when it
  crashes yet but it can still be crashed. It needs more work.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Ivan Vecera <ivecera@redhat.com>
Cc: Hayes <hayeswang@realtek.com>

I found that one of the 8168c chipsets (concretely XID 1c4000c0) starts
generating RxFIFO overflow errors. The result is an infinite loop in
interrupt handler as the RxFIFOOver is handled only for ...MAC_VER_11.
With the workaround everything goes fine.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes <hayeswang@realtek.com>

nlmsg_cancel can accept NULL as its second argument, so for similarity,
this patch extends genlmsg_cancel to be able to accept a NULL second
argument as well.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 709b46e8 ("net: Add compat
ioctl support for the ipv4 multicast ioctl SIOCGETSGCNT") added the
correct plumbing to handle SIOCGETSGCNT properly.

However, whilst definiting a proper "struct compat_sioc_sg_req" it
isn't actually used in ipmr_compat_ioctl().

Correct this oversight.
Signed-off-by: David S. Miller <davem@davemloft.net>

As reported by Flavio Leitner, there is no synchronization to protect
NIU's get_stats method from seeing a NULL pointer in either
np->rx_rings or np->tx_rings.  In fact, as far as ->ndo_get_stats
is concerned, these values are set completely asynchronously.

Flavio attempted to fix this using a RW semaphore, which in fact
works most of the time.  However, dev_get_stats() can be invoked
from non-sleepable contexts in some cases, so this fix doesn't
work in all cases.

So instead, control the visibility of the np->{rx,tx}_ring pointers
when the device is being brough up, and use properties of the device
down sequence to our advantage.

In niu_get_stats(), return immediately if netif_running() is false.
The device shutdown sequence first marks the device as not running (by
clearing the __LINK_STATE_START bit), then it performans a
synchronize_rcu() (in dev_deactive_many()), and then finally it
invokes the driver ->ndo_stop() method.

This guarentees that all invocations of niu_get_stats() either see
netif_running() as false, or they see the channel pointers before
->ndo_stop() clears them out.

If netif_running() is true, protect against startup races by loading
the np->{rx,tx}_rings pointer into a local variable, and punting if
it is NULL.  Use ACCESS_ONCE to prevent the compiler from reloading
the pointer on us.

Also, during open, control the order in which the pointers and the
ring counts become visible globally using SMP write memory barriers.
We make sure the np->num_{rx,tx}_rings value is stable and visible
before np->{rx,tx}_rings is.

Such visibility control is not necessary on the niu_free_channels()
side because of the RCU sequencing that happens during device down as
described above.  We are always guarenteed that all niu_get_stats
calls are finished, or will see netif_running() false, by the time
->ndo_stop is invoked.
Reported-by: Flavio Leitner <fleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There was some confusion at LCA as to why the sysctl tcp_ecn took one
of three values when it was documented as a Boolean.  This patch fixes
the documentation.
Signed-off-by: Peter Chubb <peter.chubb@nicta.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 8f574b35 ("atl1c: Add AR8151 v2
support and change L0s/L1 routine") added support for a new adapter
but failed to add it to the PCI device table.
Signed-Off-By: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This error was reported by cppcheck:
drivers/s390/net/smsgiucv.c:63: error: Using sizeof for array given as
function argument returns the size of pointer.

Although there is no runtime problem as long as sizeof(u8 *) == 8,
this misleading code should get fixed.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This error was reported by cppcheck:
drivers/s390/net/netiucv.c:568: error: Using sizeof for array given
as function argument returns the size of pointer.

sizeof(ipuser) did not result in 16 (as many programmers would have
expected) but sizeof(u8 *), so it is 4 or 8, too small here.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For OSA the CHPARM-definition determines the number of available
outbound queues.
A CHPARM-change may occur while a Linux system with probed
OSA device is in suspend state. This patch enables proper
resuming of an OSA device in this case.
Signed-off-by: Ursula braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For HiperSockets the framesize-definition determines the selected
mtu-size and the size of the allocated qdio buffers.
A framesize-change may occur while a Linux system with probed
HiperSockets device is in suspend state. This patch enables proper
resuming of a HiperSockets device in this case.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

HiperSockets and OSA hardware report a maximum MTU size. Add checking
to reject larger MTUs than allowed by hardware.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Setting of a MAC-address may fail because an already used MAC-address
is to bet set or because of authorization problems. In those cases
qeth issues a message, but the mentioned MAC-address is not the
new MAC-address to be set, but the actual MAC-address. This patch
chooses now the new MAC-address to be set for the error messages.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Like Herbert's change from a few days ago:

66c46d74 gro: Reset dev pointer on reuse

this may not be necessary at this point, but we should still clean up
the skb->skb_iif.  If not we may end up with an invalid valid for
skb->skb_iif when the skb is reused and the check is done in
__netif_receive_skb.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is illegal to call netif_stop_queue before register_netdev.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While running insmod/rmood in a loop, an unnecessary netif_stop_queue
causes the system to crash. Remove the netif_stop_queue call
and netif_start_queue in the link status update path.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This warning was reported by cppcheck:
drivers/isdn/icn/icn.c:1641: error: Dangerous usage of 'rev' (strncpy doesn't always 0-terminate it)

If strncpy copied 20 bytes, the destination string rev was not terminated.
The patch adds one more byte to rev and makes sure that this byte is
always 0.

Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Tejun Heo <tj@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The chip was erroneously configured to accept all multicast frames
in a normal (none-promisc) rx mode both on the RSS and on the FCoE L2 rings
when in an NPAR mode. This caused packet duplication for every received multicast
frame in this mode.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace the rather weird use of ++ with + 1 as the value is being assigned
Signed-off-by: Alan Cox <alan@linux.intel.com>

This error is reported by cppcheck:
drivers/net/vxge/vxge-config.c:3693: warning: Mutual exclusion over || always evaluates to true. Did you intend to use && instead?

It looks like cppcheck is correct, so fix this. No test was run.

Cc: Ramkrishna Vepa <ramkrishna.vepa@exar.com>
Cc: Sivakumar Subramani <sivakumar.subramani@exar.com>
Cc: Sreenivasa Honnur <sreenivasa.honnur@exar.com>
Cc: Jon Mason <jon.mason@exar.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Acked-by: Ram Vepa <ram.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

free the skb's when the Tx of PAPRD frames fails and also add a debug
message indicating that.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For the following rule:

iptables -I PREROUTING -t raw -j CT --ctevents assured

The event delivered looks like the following:

 [UPDATE] tcp      6 src=192.168.0.2 dst=192.168.1.2 sport=37041 dport=80 src=192.168.1.2 dst=192.168.1.100 sport=80 dport=37041 [ASSURED]

Note that the TCP protocol state is not included. For that reason
the CT event filtering is not very useful for conntrackd.

To resolve this issue, instead of conditionally setting the CT events
bits based on the ctmask, we always set them and perform the filtering
in the late stage, just before the delivery.

Thus, the event delivered looks like the following:

 [UPDATE] tcp      6 432000 ESTABLISHED src=192.168.0.2 dst=192.168.1.2 sport=37041 dport=80 src=192.168.1.2 dst=192.168.1.100 sport=80 dport=37041 [ASSURED]
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>

In 135367b8 "netfilter: xtables: change xt_target.checkentry return type",
the type returned by checkentry was changed from boolean to int, but the
return values where not adjusted.

arptables: Input/output error

This broke arptables with the mangle target since it returns true
under success, which is interpreted by xtables as >0, thus
returning EIO.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>

When built with rcu checks enabled, vhost triggers
bogus warnings as vhost features are read without
dev->mutex sometimes, and private pointer is read
with our kind of rcu where work serves as a
read side critical section.

Fixing it properly is not trivial.
Disable the warnings by stubbing out the checks for now.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

This error was reported by cppcheck:
drivers/net/enc28j60.c:815: error: Using sizeof for array given as function argument returns the size of pointer.

The original code reads 4 or 8 bytes instead of TSV_SIZE (= 100) bytes.
I just fixed the code, but did not run any tests.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

In my testing of 2.6.37 I was occassionally getting a warning about
sysctl table entries being unregistered in the wrong order.  Digging
in it turns out this dates back to the last great sysctl reorg done
where Al Viro introduced the requirement that sysctl directories
needed to be created before and destroyed after the files in them.

It turns out that in that great reorg /proc/sys/net/ipv6/neigh was
overlooked.  So this patch fixes that oversight and makes an annoying
warning message go away.

>------------[ cut here ]------------
>WARNING: at kernel/sysctl.c:1992 unregister_sysctl_table+0x134/0x164()
>Pid: 23951, comm: kworker/u:3 Not tainted 2.6.37-350888.2010AroraKernelBeta.fc14.x86_64 #1
>Call Trace:
> [<ffffffff8103e034>] warn_slowpath_common+0x80/0x98
> [<ffffffff8103e061>] warn_slowpath_null+0x15/0x17
> [<ffffffff810452f8>] unregister_sysctl_table+0x134/0x164
> [<ffffffff810e7834>] ? kfree+0xc4/0xd1
> [<ffffffff813439b2>] neigh_sysctl_unregister+0x22/0x3a
> [<ffffffffa02cd14e>] addrconf_ifdown+0x33f/0x37b [ipv6]
> [<ffffffff81331ec2>] ? skb_dequeue+0x5f/0x6b
> [<ffffffffa02ce4a5>] addrconf_notify+0x69b/0x75c [ipv6]
> [<ffffffffa02eb953>] ? ip6mr_device_event+0x98/0xa9 [ipv6]
> [<ffffffff813d2413>] notifier_call_chain+0x32/0x5e
> [<ffffffff8105bdea>] raw_notifier_call_chain+0xf/0x11
> [<ffffffff8133cdac>] call_netdevice_notifiers+0x45/0x4a
> [<ffffffff8133d2b0>] rollback_registered_many+0x118/0x201
> [<ffffffff8133d3af>] unregister_netdevice_many+0x16/0x6d
> [<ffffffff8133d571>] default_device_exit_batch+0xa4/0xb8
> [<ffffffff81337c42>] ? cleanup_net+0x0/0x194
> [<ffffffff81337a2a>] ops_exit_list+0x4e/0x56
> [<ffffffff81337d36>] cleanup_net+0xf4/0x194
> [<ffffffff81053318>] process_one_work+0x187/0x280
> [<ffffffff8105441b>] worker_thread+0xff/0x19f
> [<ffffffff8105431c>] ? worker_thread+0x0/0x19f
> [<ffffffff8105776d>] kthread+0x7d/0x85
> [<ffffffff81003824>] kernel_thread_helper+0x4/0x10
> [<ffffffff810576f0>] ? kthread+0x0/0x85
> [<ffffffff81003820>] ? kernel_thread_helper+0x0/0x10
>---[ end trace 8a7e9310b35e9486 ]---
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

axnet_cs:
    mdelay of 10ms is too long at ei_rx_overrun.
    It should be reduced to 2ms.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

In get_rps_cpu, add check that the rps_flow_table for the device is
NULL when trying to take fast path when RPS map length is one.
Without this, RFS is effectively disabled if map length is one which
is not correct.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Without this dependency the softing driver will be buildable on s390,
where it fails.
Signed-Off-By: Chuck Ebbert <cebbert@redhat.com>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

When an IPSEC SA is still being set up, __xfrm_lookup() will return
-EREMOTE and so ip_route_output_flow() will return a blackhole route.
This can happen in a sndmsg call, and after d33e4553 ("net: Abstract
default MTU metric calculation behind an accessor.") this leads to a
crash in ip_append_data() because the blackhole dst_ops have no
default_mtu() method and so dst_mtu() calls a NULL pointer.

Fix this by adding default_mtu() methods (that simply return 0, matching
the old behavior) to the blackhole dst_ops.

The IPv4 part of this patch fixes a crash that I saw when using an IPSEC
VPN; the IPv6 part is untested because I don't have an IPv6 VPN, but it
looks to be needed as well.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When DEBUG_SPI is included in the debug log level wl1271_spi_reset()
will dump the already freed memory instead of the SPI buffer.

This bug was spotted by the semantic patch tool coccinelle using the
script found at scripts/coccinelle/free/kfree.cocci.

More information about semantic patching is available at
http://coccinelle.lip6.fr/Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>