There are four work (mbx_service_task, service_task,
rst_service_task and keep_alive_task)in the hclgevf module,
mbx_service_task is for handling mailbox issue, service_task is
for periodic management issue and rst_service_task is for reset
related issue, keep_alive_task is used to keepalive between PF
and VF, which can be done in a single work.

This patch removes the mbx_service_task, rst_service_task and
keep_alive_task, and moves the related handling to the
service_task work in order to remove concurrency between the four
work and to improve efficiency.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are three work (mbx_service_task, service_task,
rst_service_task) in the HNS3 driver, mbx_service_task is for
handling mailbox work, service_task is for periodic management
issue and rst_service_task is for reset related issue, which can
be handled in a single work.

This patch removes the mbx_service_task and rst_service_task
work, and moves the related handling to the service_task work
in order to remove concurrency between the three work and to
improve efficiency.

BTW, since stats_timer in struct hclge_hw_stats is not needed
anymore, so removes the definition of struct hclge_hw_stats,
and moves mac_stats into struct hclge_dev.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, a timer is defined to schedule hclgevf_service per
second. To simplify the code, this patch uses the delayed work
instead of timer to schedule hclgevf_serive.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The sparse commit 6002ded74587 ("add a flag to warn on casts to/from
bitwise pointers") introduced a check for non-direct casts from/to
restricted datatypes (when -Wbitwise-pointer is enabled).

This triggered a warning in the 64 bit optimized ipv6_addr_is_*() functions
because sparse doesn't know that the buffer already points to some data in
the correct bitwise integer format. But these were correct and can
therefore be marked with __force to signalize sparse an intended cast to a
specific bitwise type.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The sparse commit 6002ded74587 ("add a flag to warn on casts to/from
bitwise pointers") introduced a check for non-direct casts from/to
restricted datatypes (when -Wbitwise-pointer is enabled).

This triggered a warning in ipv6_get_dsfield() because sparse doesn't know
that the buffer already points to some data in the correct bitwise integer
format. This was already fixed in ipv6_change_dsfield() by the __force
attribute and can be fixed here the same way.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some users complained about problems with r8169 and it turned out that
the generic PHY driver was used instead instead of the dedicated one.
In all cases reason was that r8169.ko was in initramfs, but realtek.ko
not. Manually adding realtek.ko to initramfs fixed the issues.
Root cause seems to be that tools like dracut and genkernel don't
consider softdeps. Add a check for loaded Realtek PHY driver module
and provide the user with a hint if it's not loaded.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yangbo Lu says:

====================
dpaa2-ptp: support external trigger event

This patch-set is to add external trigger event support for
dpaa2-ptp driver since MC firmware has supported external
trigger interrupt with a new v2 dprtc_set_irq_mask() API.
And extts_clean_up() function in ptp_qoriq driver needs to be
exported with minor fixes for dpaa2-ptp reusing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to add external trigger event support
for dpaa2-ptp driver with v2 dprtc_set_irq_mask() API.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Export extts_clean_up() function so that dpaa2-ptp
driver is able to reuse it.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For PTP timer supporting external trigger timestamp FIFO,
there is a valid bit in TMR_STAT register indicating the
timestamp is available. For PTP timer without FIFO, there
is not TMR_STAT register.
This patch is to check the valid bit for the FIFO before
reading timestamp, and to avoid operating TMR_STAT register
for PTP timer without the FIFO.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

At present, if the last frag of paged data in a skb has < PAGE_SIZE
data, we compute the recv_skip_hint as being equal to the size of that
frag and the entire next skb.

Instead, just return the runt frag size as the hint.

recv_skip_hint is used by the application to skip over
bytes that can not be mmaped, so returning a too big
chunk is pessimistic and forces more bytes to be copied.
Signed-off-by: Arjun Roy <arjunroy@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

Save a line of code by making use of ATOMIC_INIT() for lgr_cnt.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

of_phy_attach() hides the return value of phy_attach_direct(), forcing
us to return a "generic" ENODEV error code that is indistinguishable
from the lack-of-phy-property case.

Switch to using of_phy_find_device() to find the PHY device, and then
propagating any phy_attach_direct() error back to the caller.

Link: https://lore.kernel.org/lkml/20191210113829.GT25745@shell.armlinux.org.ukSigned-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

This adds rx_bpdu, tx_bpdu, rx_tcn, tx_tcn, transition_blk,
transition_fwd xstats counters to the bridge ports copied over via
netlink, providing useful information for STP.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

The SO_TXTIME test depends on accurate timers. In some virtualized
environments the test has been reported to be flaky. This is easily
reproduced by disabling kvm acceleration in Qemu.

Allow greater variance in a run and retry to further reduce flakiness.

Observed errors are one of two kinds: either the packet arrives too
early or late at recv(), or it was dropped in the qdisc itself and the
recv() call times out.

In the latter case, the qdisc queues a notification to the error
queue of the send socket. Also explicitly report this cause.

Link: https://lore.kernel.org/netdev/CA+FuTSdYOnJCsGuj43xwV1jxvYsaoa_LzHQF9qMyhrkLrivxKw@mail.gmail.comReported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

Fixes coccicheck warning:

drivers/net/phy/dp83869.c:337:2-3: Unneeded semicolon
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

The bond slave actor/partner operating state is exported as
bitfield to userspace, which lacks a way to interpret it, e.g.,
iproute2 only prints the state as a number:

ad_actor_oper_port_state 15

For userspace to interpret the bitfield, the bitfield definitions
should be part of the uapi. The bitfield itself is defined in the
802.3ad standard.

This commit moves the 802.3ad bitfield definitions to uapi.

Related iproute2 patches, soon to be posted upstream, use the new uapi
headers to pretty-print bond slave state, e.g., with ip -d link show

ad_actor_oper_port_state_str <active,short_timeout,aggregating,in_sync>
Signed-off-by: Andy Roulin <aroulin@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

This reverts commit 78beef62 ("nfp: abm: fix memory leak in
nfp_abm_u32_knode_replace").

The quoted commit does not fix anything and resulted in a bogus
CVE-2019-19076.

If match is NULL then it is known there is no matching entry in
list, hence, calling nfp_abm_u32_knode_delete() is pointless.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>

Michael S. Tsirkin says:

====================
netdev: ndo_tx_timeout cleanup

Yet another forward declaration I missed. Hopfully the last one ...

A bunch of drivers want to know which tx queue triggered a timeout,
and virtio wants to do the same.
We actually have the info to hand, let's just pass it on to drivers.
Note: tested with an experimental virtio patch by Julio.
That patch itself isn't ready yet though, so not included.
Other drivers compiled only.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This allows incrementing the correct timeout statistic without any mess.
Down the road, devices can learn to reset just the specific queue.

The patch was generated with the following script:

use strict;
use warnings;

our $^I = '.bak';

my @work = (
["arch/m68k/emu/nfeth.c", "nfeth_tx_timeout"],
["arch/um/drivers/net_kern.c", "uml_net_tx_timeout"],
["arch/um/drivers/vector_kern.c", "vector_net_tx_timeout"],
["arch/xtensa/platforms/iss/network.c", "iss_net_tx_timeout"],
["drivers/char/pcmcia/synclink_cs.c", "hdlcdev_tx_timeout"],
["drivers/infiniband/ulp/ipoib/ipoib_main.c", "ipoib_timeout"],
["drivers/infiniband/ulp/ipoib/ipoib_main.c", "ipoib_timeout"],
["drivers/message/fusion/mptlan.c", "mpt_lan_tx_timeout"],
["drivers/misc/sgi-xp/xpnet.c", "xpnet_dev_tx_timeout"],
["drivers/net/appletalk/cops.c", "cops_timeout"],
["drivers/net/arcnet/arcdevice.h", "arcnet_timeout"],
["drivers/net/arcnet/arcnet.c", "arcnet_timeout"],
["drivers/net/arcnet/com20020.c", "arcnet_timeout"],
["drivers/net/ethernet/3com/3c509.c", "el3_tx_timeout"],
["drivers/net/ethernet/3com/3c515.c", "corkscrew_timeout"],
["drivers/net/ethernet/3com/3c574_cs.c", "el3_tx_timeout"],
["drivers/net/ethernet/3com/3c589_cs.c", "el3_tx_timeout"],
["drivers/net/ethernet/3com/3c59x.c", "vortex_tx_timeout"],
["drivers/net/ethernet/3com/3c59x.c", "vortex_tx_timeout"],
["drivers/net/ethernet/3com/typhoon.c", "typhoon_tx_timeout"],
["drivers/net/ethernet/8390/8390.h", "ei_tx_timeout"],
["drivers/net/ethernet/8390/8390.h", "eip_tx_timeout"],
["drivers/net/ethernet/8390/8390.c", "ei_tx_timeout"],
["drivers/net/ethernet/8390/8390p.c", "eip_tx_timeout"],
["drivers/net/ethernet/8390/ax88796.c", "ax_ei_tx_timeout"],
["drivers/net/ethernet/8390/axnet_cs.c", "axnet_tx_timeout"],
["drivers/net/ethernet/8390/etherh.c", "__ei_tx_timeout"],
["drivers/net/ethernet/8390/hydra.c", "__ei_tx_timeout"],
["drivers/net/ethernet/8390/mac8390.c", "__ei_tx_timeout"],
["drivers/net/ethernet/8390/mcf8390.c", "__ei_tx_timeout"],
["drivers/net/ethernet/8390/lib8390.c", "__ei_tx_timeout"],
["drivers/net/ethernet/8390/ne2k-pci.c", "ei_tx_timeout"],
["drivers/net/ethernet/8390/pcnet_cs.c", "ei_tx_timeout"],
["drivers/net/ethernet/8390/smc-ultra.c", "ei_tx_timeout"],
["drivers/net/ethernet/8390/wd.c", "ei_tx_timeout"],
["drivers/net/ethernet/8390/zorro8390.c", "__ei_tx_timeout"],
["drivers/net/ethernet/adaptec/starfire.c", "tx_timeout"],
["drivers/net/ethernet/agere/et131x.c", "et131x_tx_timeout"],
["drivers/net/ethernet/allwinner/sun4i-emac.c", "emac_timeout"],
["drivers/net/ethernet/alteon/acenic.c", "ace_watchdog"],
["drivers/net/ethernet/amazon/ena/ena_netdev.c", "ena_tx_timeout"],
["drivers/net/ethernet/amd/7990.h", "lance_tx_timeout"],
["drivers/net/ethernet/amd/7990.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/a2065.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/am79c961a.c", "am79c961_timeout"],
["drivers/net/ethernet/amd/amd8111e.c", "amd8111e_tx_timeout"],
["drivers/net/ethernet/amd/ariadne.c", "ariadne_tx_timeout"],
["drivers/net/ethernet/amd/atarilance.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/au1000_eth.c", "au1000_tx_timeout"],
["drivers/net/ethernet/amd/declance.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/lance.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/mvme147.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/ni65.c", "ni65_timeout"],
["drivers/net/ethernet/amd/nmclan_cs.c", "mace_tx_timeout"],
["drivers/net/ethernet/amd/pcnet32.c", "pcnet32_tx_timeout"],
["drivers/net/ethernet/amd/sunlance.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/xgbe/xgbe-drv.c", "xgbe_tx_timeout"],
["drivers/net/ethernet/apm/xgene-v2/main.c", "xge_timeout"],
["drivers/net/ethernet/apm/xgene/xgene_enet_main.c", "xgene_enet_timeout"],
["drivers/net/ethernet/apple/macmace.c", "mace_tx_timeout"],
["drivers/net/ethernet/atheros/ag71xx.c", "ag71xx_tx_timeout"],
["drivers/net/ethernet/atheros/alx/main.c", "alx_tx_timeout"],
["drivers/net/ethernet/atheros/atl1c/atl1c_main.c", "atl1c_tx_timeout"],
["drivers/net/ethernet/atheros/atl1e/atl1e_main.c", "atl1e_tx_timeout"],
["drivers/net/ethernet/atheros/atlx/atl.c", "atlx_tx_timeout"],
["drivers/net/ethernet/atheros/atlx/atl1.c", "atlx_tx_timeout"],
["drivers/net/ethernet/atheros/atlx/atl2.c", "atl2_tx_timeout"],
["drivers/net/ethernet/broadcom/b44.c", "b44_tx_timeout"],
["drivers/net/ethernet/broadcom/bcmsysport.c", "bcm_sysport_tx_timeout"],
["drivers/net/ethernet/broadcom/bnx2.c", "bnx2_tx_timeout"],
["drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h", "bnx2x_tx_timeout"],
["drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c", "bnx2x_tx_timeout"],
["drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c", "bnx2x_tx_timeout"],
["drivers/net/ethernet/broadcom/bnxt/bnxt.c", "bnxt_tx_timeout"],
["drivers/net/ethernet/broadcom/genet/bcmgenet.c", "bcmgenet_timeout"],
["drivers/net/ethernet/broadcom/sb1250-mac.c", "sbmac_tx_timeout"],
["drivers/net/ethernet/broadcom/tg3.c", "tg3_tx_timeout"],
["drivers/net/ethernet/calxeda/xgmac.c", "xgmac_tx_timeout"],
["drivers/net/ethernet/cavium/liquidio/lio_main.c", "liquidio_tx_timeout"],
["drivers/net/ethernet/cavium/liquidio/lio_vf_main.c", "liquidio_tx_timeout"],
["drivers/net/ethernet/cavium/liquidio/lio_vf_rep.c", "lio_vf_rep_tx_timeout"],
["drivers/net/ethernet/cavium/thunder/nicvf_main.c", "nicvf_tx_timeout"],
["drivers/net/ethernet/cirrus/cs89x0.c", "net_timeout"],
["drivers/net/ethernet/cisco/enic/enic_main.c", "enic_tx_timeout"],
["drivers/net/ethernet/cisco/enic/enic_main.c", "enic_tx_timeout"],
["drivers/net/ethernet/cortina/gemini.c", "gmac_tx_timeout"],
["drivers/net/ethernet/davicom/dm9000.c", "dm9000_timeout"],
["drivers/net/ethernet/dec/tulip/de2104x.c", "de_tx_timeout"],
["drivers/net/ethernet/dec/tulip/tulip_core.c", "tulip_tx_timeout"],
["drivers/net/ethernet/dec/tulip/winbond-840.c", "tx_timeout"],
["drivers/net/ethernet/dlink/dl2k.c", "rio_tx_timeout"],
["drivers/net/ethernet/dlink/sundance.c", "tx_timeout"],
["drivers/net/ethernet/emulex/benet/be_main.c", "be_tx_timeout"],
["drivers/net/ethernet/ethoc.c", "ethoc_tx_timeout"],
["drivers/net/ethernet/faraday/ftgmac100.c", "ftgmac100_tx_timeout"],
["drivers/net/ethernet/fealnx.c", "fealnx_tx_timeout"],
["drivers/net/ethernet/freescale/dpaa/dpaa_eth.c", "dpaa_tx_timeout"],
["drivers/net/ethernet/freescale/fec_main.c", "fec_timeout"],
["drivers/net/ethernet/freescale/fec_mpc52xx.c", "mpc52xx_fec_tx_timeout"],
["drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c", "fs_timeout"],
["drivers/net/ethernet/freescale/gianfar.c", "gfar_timeout"],
["drivers/net/ethernet/freescale/ucc_geth.c", "ucc_geth_timeout"],
["drivers/net/ethernet/fujitsu/fmvj18x_cs.c", "fjn_tx_timeout"],
["drivers/net/ethernet/google/gve/gve_main.c", "gve_tx_timeout"],
["drivers/net/ethernet/hisilicon/hip04_eth.c", "hip04_timeout"],
["drivers/net/ethernet/hisilicon/hix5hd2_gmac.c", "hix5hd2_net_timeout"],
["drivers/net/ethernet/hisilicon/hns/hns_enet.c", "hns_nic_net_timeout"],
["drivers/net/ethernet/hisilicon/hns3/hns3_enet.c", "hns3_nic_net_timeout"],
["drivers/net/ethernet/huawei/hinic/hinic_main.c", "hinic_tx_timeout"],
["drivers/net/ethernet/i825xx/82596.c", "i596_tx_timeout"],
["drivers/net/ethernet/i825xx/ether1.c", "ether1_timeout"],
["drivers/net/ethernet/i825xx/lib82596.c", "i596_tx_timeout"],
["drivers/net/ethernet/i825xx/sun3_82586.c", "sun3_82586_timeout"],
["drivers/net/ethernet/ibm/ehea/ehea_main.c", "ehea_tx_watchdog"],
["drivers/net/ethernet/ibm/emac/core.c", "emac_tx_timeout"],
["drivers/net/ethernet/ibm/emac/core.c", "emac_tx_timeout"],
["drivers/net/ethernet/ibm/ibmvnic.c", "ibmvnic_tx_timeout"],
["drivers/net/ethernet/intel/e100.c", "e100_tx_timeout"],
["drivers/net/ethernet/intel/e1000/e1000_main.c", "e1000_tx_timeout"],
["drivers/net/ethernet/intel/e1000e/netdev.c", "e1000_tx_timeout"],
["drivers/net/ethernet/intel/fm10k/fm10k_netdev.c", "fm10k_tx_timeout"],
["drivers/net/ethernet/intel/i40e/i40e_main.c", "i40e_tx_timeout"],
["drivers/net/ethernet/intel/iavf/iavf_main.c", "iavf_tx_timeout"],
["drivers/net/ethernet/intel/ice/ice_main.c", "ice_tx_timeout"],
["drivers/net/ethernet/intel/ice/ice_main.c", "ice_tx_timeout"],
["drivers/net/ethernet/intel/igb/igb_main.c", "igb_tx_timeout"],
["drivers/net/ethernet/intel/igbvf/netdev.c", "igbvf_tx_timeout"],
["drivers/net/ethernet/intel/ixgb/ixgb_main.c", "ixgb_tx_timeout"],
["drivers/net/ethernet/intel/ixgbe/ixgbe_debugfs.c", "adapter->netdev->netdev_ops->ndo_tx_timeout(adapter->netdev);"],
["drivers/net/ethernet/intel/ixgbe/ixgbe_main.c", "ixgbe_tx_timeout"],
["drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c", "ixgbevf_tx_timeout"],
["drivers/net/ethernet/jme.c", "jme_tx_timeout"],
["drivers/net/ethernet/korina.c", "korina_tx_timeout"],
["drivers/net/ethernet/lantiq_etop.c", "ltq_etop_tx_timeout"],
["drivers/net/ethernet/marvell/mv643xx_eth.c", "mv643xx_eth_tx_timeout"],
["drivers/net/ethernet/marvell/pxa168_eth.c", "pxa168_eth_tx_timeout"],
["drivers/net/ethernet/marvell/skge.c", "skge_tx_timeout"],
["drivers/net/ethernet/marvell/sky2.c", "sky2_tx_timeout"],
["drivers/net/ethernet/marvell/sky2.c", "sky2_tx_timeout"],
["drivers/net/ethernet/mediatek/mtk_eth_soc.c", "mtk_tx_timeout"],
["drivers/net/ethernet/mellanox/mlx4/en_netdev.c", "mlx4_en_tx_timeout"],
["drivers/net/ethernet/mellanox/mlx4/en_netdev.c", "mlx4_en_tx_timeout"],
["drivers/net/ethernet/mellanox/mlx5/core/en_main.c", "mlx5e_tx_timeout"],
["drivers/net/ethernet/micrel/ks8842.c", "ks8842_tx_timeout"],
["drivers/net/ethernet/micrel/ksz884x.c", "netdev_tx_timeout"],
["drivers/net/ethernet/microchip/enc28j60.c", "enc28j60_tx_timeout"],
["drivers/net/ethernet/microchip/encx24j600.c", "encx24j600_tx_timeout"],
["drivers/net/ethernet/natsemi/sonic.h", "sonic_tx_timeout"],
["drivers/net/ethernet/natsemi/sonic.c", "sonic_tx_timeout"],
["drivers/net/ethernet/natsemi/jazzsonic.c", "sonic_tx_timeout"],
["drivers/net/ethernet/natsemi/macsonic.c", "sonic_tx_timeout"],
["drivers/net/ethernet/natsemi/natsemi.c", "ns_tx_timeout"],
["drivers/net/ethernet/natsemi/ns83820.c", "ns83820_tx_timeout"],
["drivers/net/ethernet/natsemi/xtsonic.c", "sonic_tx_timeout"],
["drivers/net/ethernet/neterion/s2io.h", "s2io_tx_watchdog"],
["drivers/net/ethernet/neterion/s2io.c", "s2io_tx_watchdog"],
["drivers/net/ethernet/neterion/vxge/vxge-main.c", "vxge_tx_watchdog"],
["drivers/net/ethernet/netronome/nfp/nfp_net_common.c", "nfp_net_tx_timeout"],
["drivers/net/ethernet/nvidia/forcedeth.c", "nv_tx_timeout"],
["drivers/net/ethernet/nvidia/forcedeth.c", "nv_tx_timeout"],
["drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c", "pch_gbe_tx_timeout"],
["drivers/net/ethernet/packetengines/hamachi.c", "hamachi_tx_timeout"],
["drivers/net/ethernet/packetengines/yellowfin.c", "yellowfin_tx_timeout"],
["drivers/net/ethernet/pensando/ionic/ionic_lif.c", "ionic_tx_timeout"],
["drivers/net/ethernet/qlogic/netxen/netxen_nic_main.c", "netxen_tx_timeout"],
["drivers/net/ethernet/qlogic/qla3xxx.c", "ql3xxx_tx_timeout"],
["drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c", "qlcnic_tx_timeout"],
["drivers/net/ethernet/qualcomm/emac/emac.c", "emac_tx_timeout"],
["drivers/net/ethernet/qualcomm/qca_spi.c", "qcaspi_netdev_tx_timeout"],
["drivers/net/ethernet/qualcomm/qca_uart.c", "qcauart_netdev_tx_timeout"],
["drivers/net/ethernet/rdc/r6040.c", "r6040_tx_timeout"],
["drivers/net/ethernet/realtek/8139cp.c", "cp_tx_timeout"],
["drivers/net/ethernet/realtek/8139too.c", "rtl8139_tx_timeout"],
["drivers/net/ethernet/realtek/atp.c", "tx_timeout"],
["drivers/net/ethernet/realtek/r8169_main.c", "rtl8169_tx_timeout"],
["drivers/net/ethernet/renesas/ravb_main.c", "ravb_tx_timeout"],
["drivers/net/ethernet/renesas/sh_eth.c", "sh_eth_tx_timeout"],
["drivers/net/ethernet/renesas/sh_eth.c", "sh_eth_tx_timeout"],
["drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c", "sxgbe_tx_timeout"],
["drivers/net/ethernet/seeq/ether3.c", "ether3_timeout"],
["drivers/net/ethernet/seeq/sgiseeq.c", "timeout"],
["drivers/net/ethernet/sfc/efx.c", "efx_watchdog"],
["drivers/net/ethernet/sfc/falcon/efx.c", "ef4_watchdog"],
["drivers/net/ethernet/sgi/ioc3-eth.c", "ioc3_timeout"],
["drivers/net/ethernet/sgi/meth.c", "meth_tx_timeout"],
["drivers/net/ethernet/silan/sc92031.c", "sc92031_tx_timeout"],
["drivers/net/ethernet/sis/sis190.c", "sis190_tx_timeout"],
["drivers/net/ethernet/sis/sis900.c", "sis900_tx_timeout"],
["drivers/net/ethernet/smsc/epic100.c", "epic_tx_timeout"],
["drivers/net/ethernet/smsc/smc911x.c", "smc911x_timeout"],
["drivers/net/ethernet/smsc/smc9194.c", "smc_timeout"],
["drivers/net/ethernet/smsc/smc91c92_cs.c", "smc_tx_timeout"],
["drivers/net/ethernet/smsc/smc91x.c", "smc_timeout"],
["drivers/net/ethernet/stmicro/stmmac/stmmac_main.c", "stmmac_tx_timeout"],
["drivers/net/ethernet/sun/cassini.c", "cas_tx_timeout"],
["drivers/net/ethernet/sun/ldmvsw.c", "sunvnet_tx_timeout_common"],
["drivers/net/ethernet/sun/niu.c", "niu_tx_timeout"],
["drivers/net/ethernet/sun/sunbmac.c", "bigmac_tx_timeout"],
["drivers/net/ethernet/sun/sungem.c", "gem_tx_timeout"],
["drivers/net/ethernet/sun/sunhme.c", "happy_meal_tx_timeout"],
["drivers/net/ethernet/sun/sunqe.c", "qe_tx_timeout"],
["drivers/net/ethernet/sun/sunvnet.c", "sunvnet_tx_timeout_common"],
["drivers/net/ethernet/sun/sunvnet_common.c", "sunvnet_tx_timeout_common"],
["drivers/net/ethernet/sun/sunvnet_common.h", "sunvnet_tx_timeout_common"],
["drivers/net/ethernet/synopsys/dwc-xlgmac-net.c", "xlgmac_tx_timeout"],
["drivers/net/ethernet/ti/cpmac.c", "cpmac_tx_timeout"],
["drivers/net/ethernet/ti/cpsw.c", "cpsw_ndo_tx_timeout"],
["drivers/net/ethernet/ti/cpsw_priv.c", "cpsw_ndo_tx_timeout"],
["drivers/net/ethernet/ti/cpsw_priv.h", "cpsw_ndo_tx_timeout"],
["drivers/net/ethernet/ti/davinci_emac.c", "emac_dev_tx_timeout"],
["drivers/net/ethernet/ti/netcp_core.c", "netcp_ndo_tx_timeout"],
["drivers/net/ethernet/ti/tlan.c", "tlan_tx_timeout"],
["drivers/net/ethernet/toshiba/ps3_gelic_net.h", "gelic_net_tx_timeout"],
["drivers/net/ethernet/toshiba/ps3_gelic_net.c", "gelic_net_tx_timeout"],
["drivers/net/ethernet/toshiba/ps3_gelic_wireless.c", "gelic_net_tx_timeout"],
["drivers/net/ethernet/toshiba/spider_net.c", "spider_net_tx_timeout"],
["drivers/net/ethernet/toshiba/tc35815.c", "tc35815_tx_timeout"],
["drivers/net/ethernet/via/via-rhine.c", "rhine_tx_timeout"],
["drivers/net/ethernet/wiznet/w5100.c", "w5100_tx_timeout"],
["drivers/net/ethernet/wiznet/w5300.c", "w5300_tx_timeout"],
["drivers/net/ethernet/xilinx/xilinx_emaclite.c", "xemaclite_tx_timeout"],
["drivers/net/ethernet/xircom/xirc2ps_cs.c", "xirc_tx_timeout"],
["drivers/net/fjes/fjes_main.c", "fjes_tx_retry"],
["drivers/net/slip/slip.c", "sl_tx_timeout"],
["include/linux/usb/usbnet.h", "usbnet_tx_timeout"],
["drivers/net/usb/aqc111.c", "usbnet_tx_timeout"],
["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"],
["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"],
["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"],
["drivers/net/usb/ax88172a.c", "usbnet_tx_timeout"],
["drivers/net/usb/ax88179_178a.c", "usbnet_tx_timeout"],
["drivers/net/usb/catc.c", "catc_tx_timeout"],
["drivers/net/usb/cdc_mbim.c", "usbnet_tx_timeout"],
["drivers/net/usb/cdc_ncm.c", "usbnet_tx_timeout"],
["drivers/net/usb/dm9601.c", "usbnet_tx_timeout"],
["drivers/net/usb/hso.c", "hso_net_tx_timeout"],
["drivers/net/usb/int51x1.c", "usbnet_tx_timeout"],
["drivers/net/usb/ipheth.c", "ipheth_tx_timeout"],
["drivers/net/usb/kaweth.c", "kaweth_tx_timeout"],
["drivers/net/usb/lan78xx.c", "lan78xx_tx_timeout"],
["drivers/net/usb/mcs7830.c", "usbnet_tx_timeout"],
["drivers/net/usb/pegasus.c", "pegasus_tx_timeout"],
["drivers/net/usb/qmi_wwan.c", "usbnet_tx_timeout"],
["drivers/net/usb/r8152.c", "rtl8152_tx_timeout"],
["drivers/net/usb/rndis_host.c", "usbnet_tx_timeout"],
["drivers/net/usb/rtl8150.c", "rtl8150_tx_timeout"],
["drivers/net/usb/sierra_net.c", "usbnet_tx_timeout"],
["drivers/net/usb/smsc75xx.c", "usbnet_tx_timeout"],
["drivers/net/usb/smsc95xx.c", "usbnet_tx_timeout"],
["drivers/net/usb/sr9700.c", "usbnet_tx_timeout"],
["drivers/net/usb/sr9800.c", "usbnet_tx_timeout"],
["drivers/net/usb/usbnet.c", "usbnet_tx_timeout"],
["drivers/net/vmxnet3/vmxnet3_drv.c", "vmxnet3_tx_timeout"],
["drivers/net/wan/cosa.c", "cosa_net_timeout"],
["drivers/net/wan/farsync.c", "fst_tx_timeout"],
["drivers/net/wan/fsl_ucc_hdlc.c", "uhdlc_tx_timeout"],
["drivers/net/wan/lmc/lmc_main.c", "lmc_driver_timeout"],
["drivers/net/wan/x25_asy.c", "x25_asy_timeout"],
["drivers/net/wimax/i2400m/netdev.c", "i2400m_tx_timeout"],
["drivers/net/wireless/intel/ipw2x00/ipw2100.c", "ipw2100_tx_timeout"],
["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"],
["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"],
["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"],
["drivers/net/wireless/intersil/orinoco/main.c", "orinoco_tx_timeout"],
["drivers/net/wireless/intersil/orinoco/orinoco_usb.c", "orinoco_tx_timeout"],
["drivers/net/wireless/intersil/orinoco/orinoco.h", "orinoco_tx_timeout"],
["drivers/net/wireless/intersil/prism54/islpci_dev.c", "islpci_eth_tx_timeout"],
["drivers/net/wireless/intersil/prism54/islpci_eth.c", "islpci_eth_tx_timeout"],
["drivers/net/wireless/intersil/prism54/islpci_eth.h", "islpci_eth_tx_timeout"],
["drivers/net/wireless/marvell/mwifiex/main.c", "mwifiex_tx_timeout"],
["drivers/net/wireless/quantenna/qtnfmac/core.c", "qtnf_netdev_tx_timeout"],
["drivers/net/wireless/quantenna/qtnfmac/core.h", "qtnf_netdev_tx_timeout"],
["drivers/net/wireless/rndis_wlan.c", "usbnet_tx_timeout"],
["drivers/net/wireless/wl3501_cs.c", "wl3501_tx_timeout"],
["drivers/net/wireless/zydas/zd1201.c", "zd1201_tx_timeout"],
["drivers/s390/net/qeth_core.h", "qeth_tx_timeout"],
["drivers/s390/net/qeth_core_main.c", "qeth_tx_timeout"],
["drivers/s390/net/qeth_l2_main.c", "qeth_tx_timeout"],
["drivers/s390/net/qeth_l2_main.c", "qeth_tx_timeout"],
["drivers/s390/net/qeth_l3_main.c", "qeth_tx_timeout"],
["drivers/s390/net/qeth_l3_main.c", "qeth_tx_timeout"],
["drivers/staging/ks7010/ks_wlan_net.c", "ks_wlan_tx_timeout"],
["drivers/staging/qlge/qlge_main.c", "qlge_tx_timeout"],
["drivers/staging/rtl8192e/rtl8192e/rtl_core.c", "_rtl92e_tx_timeout"],
["drivers/staging/rtl8192u/r8192U_core.c", "tx_timeout"],
["drivers/staging/unisys/visornic/visornic_main.c", "visornic_xmit_timeout"],
["drivers/staging/wlan-ng/p80211netdev.c", "p80211knetdev_tx_timeout"],
["drivers/tty/n_gsm.c", "gsm_mux_net_tx_timeout"],
["drivers/tty/synclink.c", "hdlcdev_tx_timeout"],
["drivers/tty/synclink_gt.c", "hdlcdev_tx_timeout"],
["drivers/tty/synclinkmp.c", "hdlcdev_tx_timeout"],
["net/atm/lec.c", "lec_tx_timeout"],
["net/bluetooth/bnep/netdev.c", "bnep_net_timeout"]
);

for my $p (@work) {
	my @pair = @$p;
	my $file = $pair[0];
	my $func = $pair[1];
	print STDERR $file , ": ", $func,"\n";
	our @ARGV = ($file);
	while (<ARGV>) {
		if (m/($func\s*\(struct\s+net_device\s+\*[A-Za-z_]?[A-Za-z-0-9_]*)(\))/) {
			print STDERR "found $1+$2 in $file\n";
		}
		if (s/($func\s*\(struct\s+net_device\s+\*[A-Za-z_]?[A-Za-z-0-9_]*)(\))/$1, unsigned int txqueue$2/) {
			print STDERR "$func found in $file\n";
		}
		print;
	}
}

where the list of files and functions is simply from:

git grep ndo_tx_timeout, with manual addition of headers
in the rare cases where the function is from a header,
then manually changing the few places which actually
call ndo_tx_timeout.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Reviewed-by: Martin Habets <mhabets@solarflare.com>

changes from v9:
	fixup a forward declaration
changes from v9:
	more leftovers from v3 change
changes from v8:
        fix up a missing direct call to timeout
        rebased on net-next
changes from v7:
	fixup leftovers from v3 change
changes from v6:
	fix typo in rtl driver
changes from v5:
	add missing files (allow any net device argument name)
changes from v4:
	add a missing driver header
changes from v3:
        change queue # to unsigned
Changes from v2:
        added headers
Changes from v1:
        Fix errors found by kbuild:
        generalize the pattern a bit, to pick up
        a couple of instances missed by the previous
        version.
Signed-off-by: David S. Miller <davem@davemloft.net>

Sameeh Jubran says:

====================
Introduce XDP to ena

This patchset includes 3 patches:
* XDP_DROP implementation
* XDP_TX implementation
* A fix for an issue which might occur due to the XDP_TX patch. I see fit
  to place it as a standalone patch for clarity.

Difference from v2:
* Fixed the usage of rx headroom (XDP_PACKET_HEADROOM)
* Aligned the page_offset of the packet when passing it to the stack
* Switched to using xdp_frame in xdp xmit queue
* Dropped the print for unsupported commands
* Cosmetic changes

Difference from RFC v1 (XDP_DROP patch):
* Initialized xdp.rxq pointer
* Updated max_mtu on attachment of xdp and removed the check from
  ena_change_mtu()
* Moved the xdp execution from ena_rx_skb() to ena_clean_rx_irq()
* Moved xdp buff (struct xdp_buff) from rx_ring to the local stack
* Started using netlink's extack mechanism to deliver error messages to
  the user
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The first_interrupt field is accessed in ena_intr_msix_io() upon
receiving an interrupt.The rx_ring and tx_ring fields of napi can
be NULL when receiving interrupt for xdp queues. This patch fixes
the issue by moving the field to the ena_napi struct.
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit implements the XDP_TX action in the ena driver. We allocate
separate tx queues for the XDP_TX. We currently allow xdp only when
there is enough queues to allocate for xdp.
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This commit implements the basic functionality of drop/pass logic in the
ena driver.
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michal Kubecek says:

====================
ethtool netlink interface, preliminary part

As Jakub Kicinski suggested in ethtool netlink v7 discussion, this
submission consists only of preliminary patches which raised no objections;
first four patches already have Acked-by or Reviewed-by.

- patch 1 exposes permanent hardware address (as shown by "ethtool -P")
  via rtnetlink
- patch 2 is renames existing netlink helper to a better name
- patch 3 and 4 reorganize existing ethtool code (no functional change)
- patch 5 makes the table of link mode names available as an ethtool string
  set (will be needed for the netlink interface)

Once we get these out of the way, v8 of the first part of the ethtool
netlink interface will follow.

Changes from v2 to v3: fix SPDX licence identifiers (patch 3 and 5).

Changes from v1 to v2: restore build time check that all link modes have
assigned a name (patch 5).
====================
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Unlike e.g. netdev features, the ethtool ioctl interface requires link mode
table to be in sync between kernel and userspace for userspace to be able
to display and set all link modes supported by kernel. The way arbitrary
length bitsets are implemented in netlink interface, this will be no longer
needed.

To allow userspace to access all link modes running kernel supports, add
table of ethernet link mode names and make it available as a string set to
userspace GET_STRSET requests. Add build time check to make sure names
are defined for all modes declared in enum ethtool_link_mode_bit_indices.

Once the string set is available, make it also accessible via ioctl.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce file net/ethtool/common.c for code shared by ioctl and netlink
ethtool interface. Move name tables of features, RSS hash functions,
tunables and PHY tunables into this file.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ethtool netlink interface is going to be split into multiple files so
that it will be more convenient to put all of them in a separate directory
net/ethtool. Start by moving current ethtool.c with ioctl interface into
this directory and renaming it to ioctl.c.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Function nl80211_validate_nested() is not specific to nl80211, it's
a counterpart to nla_validate_nested_deprecated() with strict validation.
For consistency with other validation and parse functions, rename it to
nla_validate_nested().
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Permanent hardware address of a network device was traditionally provided
via ethtool ioctl interface but as Jiri Pirko pointed out in a review of
ethtool netlink interface, rtnetlink is much more suitable for it so let's
add it to the RTM_NEWLINK message.

Add IFLA_PERM_ADDRESS attribute to RTM_NEWLINK messages unless the
permanent address is all zeros (i.e. device driver did not fill it). As
permanent address is not modifiable, reject userspace requests containing
IFLA_PERM_ADDRESS attribute.

Note: we already provide permanent hardware address for bond slaves;
unfortunately we cannot drop that attribute for backward compatibility
reasons.

v5 -> v6: only add the attribute if permanent address is not zero
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kirill Tkhai says:

====================
unix: Show number of scm files in fdinfo

v2: Pass correct argument to locked in patch [2/2].

Unix sockets like a block box. You never know what is pending there:
there may be a file descriptor holding a mount or a block device,
or there may be whole universes with namespaces, sockets with receive
queues full of sockets etc.

The patchset makes number of pending scm files be visible in fdinfo.
This may be useful to determine, that socket should be investigated
or which task should be killed to put a reference counter on a resourse.

$cat /proc/[pid]/fdinfo/[unix_sk_fd] | grep scm_fds
scm_fds: 1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Unix sockets like a block box. You never know what is stored there:
there may be a file descriptor holding a mount or a block device,
or there may be whole universes with namespaces, sockets with receive
queues full of sockets etc.

The patch adds a little debug and accounts number of files (not recursive),
which is in receive queue of a unix socket. Sometimes this is useful
to determine, that socket should be investigated or which task should
be killed to put reference counter on a resourse.

v2: Pass correct argument to lockdep
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds .show_fdinfo to socket_file_ops, so protocols will be able
to print their specific data in fdinfo.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Stefano Garzarella says:

====================
vsock: add local transport support

v2:
 - style fixes [Dave]
 - removed RCU sync and changed 'the_vsock_loopback' in a global
   static variable [Stefan]
 - use G2H transport when local transport is not loaded and remote cid
   is VMADDR_CID_LOCAL [Stefan]
 - rebased on net-next

v1: https://patchwork.kernel.org/cover/11251735/

This series introduces a new transport (vsock_loopback) to handle
local communication.
This could be useful to test vsock core itself and to allow developers
to test their applications without launching a VM.

Before this series, vmci and virtio transports allowed this behavior,
but only in the guest.
We are moving the loopback handling in a new transport, because it
might be useful to provide this feature also in the host or when
no H2G/G2H transports (hyperv, virtio, vmci) are loaded.

The user can use the loopback with the new VMADDR_CID_LOCAL (that
replaces VMADDR_CID_RESERVED) in any condition.
Otherwise, if the G2H transport is loaded, it can also use the guest
local CID as previously supported by vmci and virtio transports.
If G2H transport is not loaded, the user can also use VMADDR_CID_HOST
for local communication.

Patch 1 is a cleanup to build virtio_transport_common without virtio
Patch 2 adds the new VMADDR_CID_LOCAL, replacing VMADDR_CID_RESERVED
Patch 3 adds a new feature flag to register a loopback transport
Patch 4 adds the new vsock_loopback transport based on the loopback
        implementation of virtio_transport
Patch 5 implements the logic to use the local transport for loopback
        communication
Patch 6 removes the loopback from virtio_transport
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We can remove the loopback handling from virtio_transport,
because now the vsock core is able to handle local communication
using the new vsock_loopback device.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that we have a transport that can handle the local communication,
we can use it when it is loaded.

A socket will use the local transport (loopback) when the remote
CID is:
- equal to VMADDR_CID_LOCAL
- or equal to transport_g2h->get_local_cid(), if transport_g2h
  is loaded (this allows us to keep the same behavior implemented
  by virtio and vmci transports)
- or equal to VMADDR_CID_HOST, if transport_g2h is not loaded
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a new vsock_loopback transport to handle local
communication.
This transport is based on the loopback implementation of
virtio_transport, so it uses the virtio_transport_common APIs
to interface with the vsock core.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch allows to register a transport able to handle
local communication (loopback).
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>