- 28 May, 2021 35 commits
-
-
Gustavo A. R. Silva authored
In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning by explicitly adding a break statement instead of letting the code fall through to the next case. Link: https://github.com/KSPP/linux/issues/115Signed-off-by:
Gustavo A. R. Silva <gustavoars@kernel.org> Acked-by:
Heiner Kallweit <hkallweit1@gmail.com> Link: https://lore.kernel.org/r/20210528202327.GA39994@embeddedorSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Vladimir Oltean authored
stmmac_mdio_register() has logic to search for PHYs on the MDIO bus and assign them IRQ lines, as well as to set priv->plat->phy_addr. If no PHY is found, the "found" variable remains set to 0 and the function errors out. After the introduction of commit f213bbe8 ("net: stmmac: Integrate it with DesignWare XPCS"), the "found" variable was immediately reused for searching for a PCS on the same MDIO bus. This can result in 2 types of potential problems (none of them seems to be seen on the only Intel system that sets has_xpcs = true, otherwise it would have been reported): 1. If a PCS is found but a PHY is not, then the code happily exits with no error. One might say "yes, but this is not possible, because of_mdiobus_register will probe a PHY for all MDIO addresses, including for the XPCS, so if an XPCS exists, then a PHY certainly exists too". Well, that is not true, see intel_mgbe_common_data(): /* Ensure mdio bus scan skips intel serdes and pcs-xpcs */ plat->mdio_bus_data->phy_mask = 1 << INTEL_MGBE_ADHOC_ADDR; plat->mdio_bus_data->phy_mask |= 1 << INTEL_MGBE_XPCS_ADDR; 2. A PHY is found but an MDIO device with the XPCS PHY ID isn't, and in that case, the error message will be "No PHY found". Confusing. Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20210527155959.3270478-1-olteanv@gmail.comSigned-off-by:
-
Krzysztof Kozlowski authored
The driver can match either via OF or ACPI ID tables. If one configuration is disabled, the table will be unused: drivers/nfc/st95hf/core.c:1059:34: warning: ‘st95hf_spi_of_match’ defined but not used [-Wunused-const-variable=] Signed-off-by:Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Link: https://lore.kernel.org/r/20210528124200.79655-12-krzysztof.kozlowski@canonical.comSigned-off-by:
-
Krzysztof Kozlowski authored
The driver can match either via OF or ACPI ID tables. If one configuration is disabled, the table will be unused: drivers/nfc/st21nfca/i2c.c:593:34: warning: ‘of_st21nfca_i2c_match’ defined but not used [-Wunused-const-variable=] Signed-off-by: -
Krzysztof Kozlowski authored
The driver can match either via OF or ACPI ID tables. If one configuration is disabled, the table will be unused: drivers/nfc/st-nci/spi.c:296:34: warning: ‘of_st_nci_spi_match’ defined but not used [-Wunused-const-variable=] Signed-off-by: -
Krzysztof Kozlowski authored
The driver can match either via OF or ACPI ID tables. If one configuration is disabled, the table will be unused: drivers/nfc/pn544/i2c.c:53:36: warning: ‘pn544_hci_i2c_acpi_match’ defined but not used [-Wunused-const-variable=] Signed-off-by: -
Krzysztof Kozlowski authored
The driver can match either via OF or I2C ID tables. If OF is disabled, the table will be unused: drivers/nfc/s3fwrn5/i2c.c:265:34: warning: ‘of_s3fwrn5_i2c_match’ defined but not used [-Wunused-const-variable=] Signed-off-by: -
Krzysztof Kozlowski authored
The driver can match either via OF or I2C ID tables. If OF is disabled, the table will be unused: drivers/nfc/pn533/i2c.c:252:34: warning: ‘of_pn533_i2c_match’ defined but not used [-Wunused-const-variable=] Signed-off-by: -
Krzysztof Kozlowski authored
The nci_ctrl_hdr.plen field us u8, so checkign if it is bigger than NCI_MAX_PAYLOAD_SIZE does not make any sense. Fix warning reported by Smatch: drivers/nfc/nfcmrvl/i2c.c:52 nfcmrvl_i2c_read() warn: impossible condition '(nci_hdr.plen > 255) => (0-255 > 255)' Signed-off-by: -
Krzysztof Kozlowski authored
The driver can match either via OF or I2C ID tables. If OF is disabled, the table will be unused: drivers/nfc/nfcmrvl/spi.c:199:34: warning: ‘of_nfcmrvl_spi_match’ defined but not used [-Wunused-const-variable=] Signed-off-by: -
Krzysztof Kozlowski authored
The driver can match only via the DT table so the table should be always used and the of_match_ptr does not have any sense (this also allows ACPI matching via PRP0001, even though it might be not relevant here). This fixes compile warning (!CONFIG_OF): drivers/nfc/pn533/i2c.c:252:34: warning: ‘of_pn533_i2c_match’ defined but not used [-Wunused-const-variable=] Signed-off-by: -
Krzysztof Kozlowski authored
The port100_in_rf_setting structure does not contain valid kerneldoc docummentation, unlike the port100_tg_rf_setting structure. Correct the kerneldoc to fix W=1 warnings: warning: This comment starts with '/**', but isn't a kernel-doc comment. Signed-off-by: -
Krzysztof Kozlowski authored
The driver can match only via the ACPI ID table so the table should be always used and the ACPI_PTR does not have any sense. This fixes fixes compile warning (!CONFIG_ACPI): drivers/nfc/fdp/i2c.c:362:36: warning: ‘fdp_nci_i2c_acpi_match’ defined but not used [-Wunused-const-variable=] Signed-off-by: -
Krzysztof Kozlowski authored
Since structure comments are not kerneldoc, remove the double ** to fix W=1 warnings: warning: This comment starts with '/**', but isn't a kernel-doc comment. Signed-off-by: -
Lorenzo Bianconi authored
Introduce k parameter in pktgen samples in order to toggle UDP tx checksum Signed-off-by:
Lorenzo Bianconi <lorenzo@kernel.org> Acked-by:
Jesper Dangaard Brouer <brouer@redhat.com> Link: https://lore.kernel.org/r/cf16417902062c6ea2fd3c79e00510e36a40c31a.1622210713.git.lorenzo@kernel.orgSigned-off-by:
-
Jakub Kicinski authored
Peng Li says: ==================== net: hdlc_fr: clean up some code style issues V1 -> V2: 1, Use appropriate commit prefix suggested by Jakub Kicinski, replace commit prefix "net: wan" by "net: hdlc_fr". ==================== Link: https://lore.kernel.org/r/1622160769-6678-1-git-send-email-huangguangbin2@huawei.comSigned-off-by:
-
Peng Li authored
This patch removes unnecessary out of memory message, to fix the following checkpatch.pl warning: "WARNING: Possible unnecessary 'out of memory' message" Signed-off-by:
Peng Li <lipeng321@huawei.com> Signed-off-by:
Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by:
-
Peng Li authored
This patch removes redundant braces {}, to fix the checkpatch.pl warning: "braces {} are not necessary for any arm of this statement" Signed-off-by: -
Peng Li authored
Braces {} should be used on all arms of this statement. Signed-off-by: -
Peng Li authored
According to the chackpatch.pl, space prohibited after that '!'. Signed-off-by:
-
Peng Li authored
Code indent should use tabs where possible. Signed-off-by:
-
Peng Li authored
Should not use assignment in if condition. Signed-off-by:
-
Peng Li authored
Add spaces required after that close brace '}'. Add spaces required before the open parenthesis '('. Add spaces required after that ','. Add spaces required around that '='. Signed-off-by: -
Peng Li authored
Fix the checkpatch error as "foo* bar" and should be "foo *bar", and "(foo*)" should be "(foo *)". Signed-off-by:
-
Peng Li authored
This patch fixes the checkpatch error about missing a blank line after declarations. Signed-off-by:
-
Peng Li authored
This patch removes some redundant blank lines. Signed-off-by:
-
Jakub Kicinski authored
Mat Martineau says: ==================== mptcp: Miscellaneous cleanup Here are some cleanup patches we've collected in the MPTCP tree. Patches 1-4 do some general tidying. Patch 5 adds an explicit check at netlink command parsing time to require a port number when the 'signal' flag is set, to catch the error earlier. Patches 6 & 7 fix up the MPTCP 'enabled' sysctl, enforcing it as a boolean value, and ensuring that the !CONFIG_SYSCTL build still works after the boolean change. ==================== Link: https://lore.kernel.org/r/20210527235430.183465-1-mathew.j.martineau@linux.intel.comSigned-off-by:
-
Matthieu Baerts authored
To avoid confusions, it seems better to parse this sysctl parameter as a boolean. We use it as a boolean, no need to parse an integer and bring confusions if we see a value different from 0 and 1, especially with this parameter name: enabled. It seems fine to do this modification because the default value is 1 (enabled). Then the only other interesting value to set is 0 (disabled). All other values would not have changed the default behaviour. Suggested-by:
Florian Westphal <fw@strlen.de> Acked-by:
Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by:
Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by:
-
Matthieu Baerts authored
Since the introduction of the sysctl support in MPTCP with commit 784325e9 ("mptcp: new sysctl to control the activation per NS"), we don't check CONFIG_SYSCTL. Until now, that was not an issue: the register and unregister functions were replaced by NO-OP one if SYSCTL was not enabled in the config. The only thing we could have avoid is not to reserve memory for the table but that's for the moment only a small table per net-ns. But the following commit is going to use SYSCTL_ZERO and SYSCTL_ONE which are not be defined if SYSCTL is not enabled in the config. This causes 'undefined reference' errors from the linker. Reported-by:
kernel test robot <lkp@intel.com> Signed-off-by:
-
Jianguo Wu authored
When add address with port, it is mean to create a listening socket, and send an ADD_ADDR to remote, so it must have flag signal set, add this check in mptcp_pm_parse_addr(). Fixes: a77e9179 ("mptcp: deal with MPTCP_PM_ADDR_ATTR_PORT in PM netlink") Acked-by:
Geliang Tang <geliangtang@gmail.com> Reviewed-by:
Jianguo Wu <wujianguo@chinatelecom.cn> Signed-off-by:
-
Jianguo Wu authored
Memory of struct pm_nl_pernet{} is allocated by kzalloc() in setup_net()->ops_init(), so it's no need to reset counters and zero bitmap in pm_nl_init_net(). Acked-by:Paolo Abeni <pabeni@redhat.com> Reviewed-by:
-
Jianguo Wu authored
For outgoing subflow join, when recv SYNACK, in subflow_finish_connect(), the mptcp_finish_join() may return false in some cases, and send a RESET to remote, and no local hmac is required. So generate subflow hmac after mptcp_finish_join(). Fixes: ec3edaa7 ("mptcp: Add handling of outgoing MP_JOIN requests") Signed-off-by:
-
Jianguo Wu authored
We have macro TOKEN_MAX_RETRIES for the number of token generate retries, so using TOKEN_MAX_RETRIES in subflow_check_req(). And rename TOKEN_MAX_RETRIES to MPTCP_TOKEN_MAX_RETRIES as it is now exposed. Fixes: 535fb815 ("mptcp: token: move retry to caller") Reviewed-by:
-
Jianguo Wu authored
After commit 2c5ebd00 ("mptcp: refactor token container"), pr_debug() is called before mptcp_crypto_key_gen_sha() in mptcp_token_new_connect(), so the output local_key, token and idsn are 0, like: MPTCP: ssk=00000000f6b3c4a2, local_key=0, token=0, idsn=0 Move pr_debug() after mptcp_crypto_key_gen_sha(). Fixes: 2c5ebd00 ("mptcp: refactor token container") Acked-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linuxJakub Kicinski authored
Saeed Mahameed says: ==================== mlx5-updates-2021-05-26 Misc update for mlx5 driver, 1) Clean up patches for lag and SF 2) Reserve bit 31 in steering register C1 for IPSec offload usage 3) Move steering tables pool logic into the steering core and increase the maximum table size to 2G entries when software steering is enabled. * tag 'mlx5-updates-2021-05-26' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux: net/mlx5: Fix lag port remapping logic net/mlx5: Use boolean arithmetic to evaluate roce_lag net/mlx5: Remove unnecessary spin lock protection net/mlx5: Cap the maximum flow group size to 16M entries net/mlx5: DR, Set max table size to 2G entries net/mlx5: Move chains ft pool to be used by all firmware steering net/mlx5: Move table size calculation to steering cmd layer net/mlx5: Add case for FS_FT_NIC_TX FT in MLX5_CAP_FLOWTABLE_TYPE net/mlx5: DR, Remove unused field of send_ring struct net/mlx5e: RX, Remove unnecessary check in RX CQE compression handling net/mlx5e: IPsec/rep_tc: Fix rep_tc_update_skb drops IPsec packet net/mlx5e: TC: Reserved bit 31 of REG_C1 for IPsec offload net/mlx5e: TC: Use bit counts for register mapping net/mlx5: CT: Avoid reusing modify header context for natted entries net/mlx5e: CT, Remove newline from ct_dbg call ==================== Link: https://lore.kernel.org/r/20210527185624.694304-1-saeed@kernel.orgSigned-off-by:
-
- 27 May, 2021 5 commits
-
-
Gustavo A. R. Silva authored
Replace union with a couple of pointers in order to fix the following out-of-bounds warning: CC [M] drivers/net/ethernet/intel/ixgbe/ixgbe_common.o drivers/net/ethernet/intel/ixgbe/ixgbe_common.c: In function ‘ixgbe_host_interface_command’: drivers/net/ethernet/intel/ixgbe/ixgbe_common.c:3729:13: warning: array subscript 1 is above array bounds of ‘u32[1]’ {aka ‘unsigned int[1]’} [-Warray-bounds] 3729 | bp->u32arr[bi] = IXGBE_READ_REG_ARRAY(hw, IXGBE_FLEX_MNG, bi); | ~~~~~~~~~~^~~~ drivers/net/ethernet/intel/ixgbe/ixgbe_common.c:3682:7: note: while referencing ‘u32arr’ 3682 | u32 u32arr[1]; | ^~~~~~ This helps with the ongoing efforts to globally enable -Warray-bounds. Link: https://github.com/KSPP/linux/issues/109Co-developed-by:Kees Cook <keescook@chromium.org> Signed-off-by:
Dave Switzer <david.switzer@intel.com> Signed-off-by:
Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20210527173424.362456-1-anthony.l.nguyen@intel.comSigned-off-by:
-
Jakub Kicinski authored
Gatis Peisenieks says: ==================== add 4 RX/TX queue support for Mikrotik 10/25G NIC More RX/TX queues on a network card help spread the CPU load among cores and achieve higher overall networking performance. This patch set adds support for 4 RX/TX queues available on Mikrotik 10/25G NIC. v4: - addressed comments from Jakub Kicinski: - split up the change in more manageable chunks - changed member order in structs for tighter packing - fixed style issues - reverted to calling napi_alloc_skb only from within poll as before v3: - fix kernel-doc complaints on comments as pointed out by David Miller v2: - rebase on net-next master as requested by David Miller ==================== Link: https://lore.kernel.org/r/20210527144423.3395719-1-gatis@mikrotik.comSigned-off-by: -
Gatis Peisenieks authored
More RX/TX queues on a network card help spread the CPU load among cores and achieve higher overall networking performance. The new Mikrotik 10/25G NIC supports 4 RX and 4 TX queues. TX queues are treated with equal priority. RX queue balancing is fixed based on L2/L3/L4 hash. This adds support for 4 RX/TX queues while maintaining backwards compatibility with older hardware. Simultaneous TX + RX performance on AMD Threadripper 3960X with Mikrotik 10/25G NIC improved from 1.6Mpps to 3.2Mpps per port. Backwards compatiblitiy was verified with AR8151 and AR8131 based NICs. Signed-off-by:
Gatis Peisenieks <gatis@mikrotik.com> Signed-off-by:
-
Gatis Peisenieks authored
Move napi and other per queue members into per rx queue struct. Allocate max rx queues that any hw supported by the driver might have. Patch that actually enables multiple rx queues will follow. Signed-off-by:
-
Gatis Peisenieks authored
To get more performance from using multiple tx queues one needs a per tx queue napi. Move tx napi from per adapter struct into per tx queue struct. Patch that actually enables multiple tx queues will follow. Signed-off-by:
-
