- 12 Mar, 2018 7 commits
-
-
Stephane Grosjean authored
When an interface starts, the echo_skb array is empty and the network queue should be started only. This patch replaces useless code and locks when the internal RX_BARRIER message is received from the IP core, telling the driver that tx may start. Signed-off-by:
Stephane Grosjean <s.grosjean@peak-system.com> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de>
-
Stephane Grosjean authored
This patch makes atomic the handling of the linux-can echo_skb array and the network tx queue. This prevents from the "BUG! echo_skb is occupied!" message to be printed by the linux-can core, in SMP environments. Reported-by:
Diana Burgess <diana@peloton-tech.com> Signed-off-by:
-
Marek Vasut authored
The new version of the IFI CANFD core has significantly less complex error state indication logic. In particular, the warning/error state bits are no longer all over the place, but are all present in the STATUS register. Moreover, there is a new IRQ register bit indicating transition between error states (active/warning/passive/busoff). This patch makes use of this bit to weed out the obscure selective INTERRUPT register clearing, which was used to carry over the error state indication into the poll function. While at it, this patch fixes the handling of the ACTIVE state, since the hardware provides indication of the core being in ACTIVE state and that in turn fixes the state transition indication toward userspace. Finally, register reads in the poll function are moved to the matching subfunctions since those are also no longer needed in the poll function. Signed-off-by:
Marek Vasut <marex@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Markus Marb <markus@marb.org> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by:
-
Marek Vasut authored
Older versions of the core are not compatible with the driver due to various intrusive fixes of the core. Read out the VER register, check the core revision bitfield and verify if the core in use is new enough (rev 2.1 or newer) to work correctly with this driver. Signed-off-by:
-
Wolfram Sang authored
Due to a typo, the mask was destroyed by a comparison instead of a bit shift. Reported-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by:
-
zhangliping authored
Max delat_t should be the full_bucket/rate instead of the full_bucket. Also report EINVAL if the rate is zero. Fixes: 96fbc13d ("openvswitch: Add meter infrastructure") Cc: Andy Zhou <azhou@ovn.org> Signed-off-by:
zhangliping <zhangliping02@baidu.com> Acked-by:
Pravin B Shelar <pshelar@ovn.org> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Shannon Nelson authored
Adding a macvlan device on top of a lowerdev that supports the xfrm offloads fails with a new regression: # ip link add link ens1f0 mv0 type macvlan RTNETLINK answers: Operation not permitted Tracing down the failure shows that the macvlan device inherits the NETIF_F_HW_ESP and NETIF_F_HW_ESP_TX_CSUM feature flags from the lowerdev, but with no dev->xfrmdev_ops API filled in, it doesn't actually support xfrm. When the request is made to add the new macvlan device, the XFRM listener for NETDEV_REGISTER calls xfrm_api_check() which fails the new registration because dev->xfrmdev_ops is NULL. The macvlan creation succeeds when we filter out the ESP feature flags in macvlan_fix_features(), so let's filter them out like we're already filtering out ~NETIF_F_NETNS_LOCAL. When XFRM support is added in the future, we can add the flags into MACVLAN_FEATURES. This same problem could crop up in the future with any other new feature flags, so let's filter out any flags that aren't defined as supported in macvlan. Fixes: d77e38e6 ("xfrm: Add an IPsec hardware offloading API") Reported-by:
Alexey Kodanev <alexey.kodanev@oracle.com> Signed-off-by:
Shannon Nelson <shannon.nelson@oracle.com> Signed-off-by:
-
- 09 Mar, 2018 15 commits
-
-
David S. Miller authored
William Tu says: ==================== a couple of erspan fixes The series fixes a couple of erspan issues. The first patch adds the erspan v2 proto type to the ip6 tunnel lookup. The second patch improves the error handling when users screws the version number in metadata. The final patch makes sure the skb has enough headroom for pushing erspan header when xmit. ==================== Signed-off-by: -
William Tu authored
The patch adds skb_cow_header() to ensure enough headroom at ip6erspan_tunnel_xmit before pushing the erspan header to the skb. Signed-off-by:
William Tu <u9012063@gmail.com> Signed-off-by:
-
William Tu authored
When users fill in incorrect erspan version number through the struct erspan_metadata uapi, current code skips pushing the erspan header but continue pushing the gre header, which is incorrect. The patch fixes it by returning error. Signed-off-by:
-
William Tu authored
The patch adds the erspan v2 proto in ip6gre_tunnel_lookup so the erspan v2 tunnel can be found correctly. Signed-off-by:
-
David S. Miller authored
Ido Schimmel says: ==================== mlxsw: ACL and mirroring fixes The first patch fixes offload of rules using the 'pass' action. Instead of continuing to evaluate lower priority rules, the binding is terminated and the packet proceeds to the bridge and router blocks on ingress, or goes out of the port on egress. Second patch prevents the user from mirroring more than once from a given {Port, Direction} as this is not supported by the device. ==================== Signed-off-by: -
Petr Machata authored
The Spectrum ASIC doesn't support mirroring more than once from a single binding point (which is a port-direction pair). Therefore detect that a second binding of a given binding point is attempted. To that end, extend struct mlxsw_sp_span_inspected_port to track whether a given binding point is bound or not. Extend mlxsw_sp_span_entry_port_find() to look for ports based on the full unique key: port number, direction, and boundness. Besides fixing the overt bug where configured mirrors are not offloaded, this also fixes a more subtle bug: mlxsw_sp_span_inspected_port_del() just defers to mlxsw_sp_span_entry_bound_port_find(), and that used to find the first port with the right number (disregarding the type). Thus by adding and removing egress and ingress mirrors in the right order, one could trick the system into believing it has no egress mirrors when in fact it did have some. That then caused that mlxsw_sp_span_port_mtu_update() didn't update mirroring buffer when MTU was changed. Fixes: 763b4b70 ("mlxsw: spectrum: Add support in matchall mirror TC offloading") Signed-off-by:
Petr Machata <petrm@mellanox.com> Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
-
Jiri Pirko authored
For ok GACT action, TERMINATE binding_cmd should be used in action set passed down to HW. Fixes: b2925957 ("mlxsw: spectrum_flower: Offload "ok" termination action") Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Reported-by:
Alexander Petrovskiy <alexpe@mellanox.com> Signed-off-by:
-
David S. Miller authored
Jason Wang says: ==================== Several fixes for vhost_net ptr_ring usage This small series try to fix several bugs of ptr_ring usage in vhost_net. Please review. ==================== Signed-off-by: -
Jason Wang authored
After commit fc72d1d5 ("tuntap: XDP transmission"), we can actually queueing XDP pointers in the pointer ring, so we should examine the pointer type before freeing the pointer. Fixes: fc72d1d5 ("tuntap: XDP transmission") Reported-by:
Michael S. Tsirkin <mst@redhat.com> Acked-by:
Jason Wang <jasowang@redhat.com> Signed-off-by:
-
Jason Wang authored
We get pointer ring from the exported sock, this means we should keep rx_ring and vq->private synced during both vq stop and backend set, otherwise we may see stale rx_ring. Fixes: c67df11f ("vhost_net: try batch dequing from skb array") Signed-off-by:
-
Alexander Potapenko authored
KMSAN reported a use of uninit memory in vhost_net_buf_unproduce() while trying to access n->vqs[VHOST_NET_VQ_TX].rx_ring: ================================================================== BUG: KMSAN: use of uninitialized memory in vhost_net_buf_unproduce+0x7bb/0x9a0 drivers/vho et.c:170 CPU: 0 PID: 3021 Comm: syz-fuzzer Not tainted 4.16.0-rc4+ #3853 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014 Call Trace: __dump_stack lib/dump_stack.c:17 [inline] dump_stack+0x185/0x1d0 lib/dump_stack.c:53 kmsan_report+0x142/0x1f0 mm/kmsan/kmsan.c:1093 __msan_warning_32+0x6c/0xb0 mm/kmsan/kmsan_instr.c:676 vhost_net_buf_unproduce+0x7bb/0x9a0 drivers/vhost/net.c:170 vhost_net_stop_vq drivers/vhost/net.c:974 [inline] vhost_net_stop+0x146/0x380 drivers/vhost/net.c:982 vhost_net_release+0xb1/0x4f0 drivers/vhost/net.c:1015 __fput+0x49f/0xa00 fs/file_table.c:209 ____fput+0x37/0x40 fs/file_table.c:243 task_work_run+0x243/0x2c0 kernel/task_work.c:113 tracehook_notify_resume include/linux/tracehook.h:191 [inline] exit_to_usermode_loop arch/x86/entry/common.c:166 [inline] prepare_exit_to_usermode+0x349/0x3b0 arch/x86/entry/common.c:196 syscall_return_slowpath+0xf3/0x6d0 arch/x86/entry/common.c:265 do_syscall_64+0x34d/0x450 arch/x86/entry/common.c:292 ... origin: kmsan_save_stack_with_flags mm/kmsan/kmsan.c:303 [inline] kmsan_internal_poison_shadow+0xb8/0x1b0 mm/kmsan/kmsan.c:213 kmsan_kmalloc_large+0x6f/0xd0 mm/kmsan/kmsan.c:392 kmalloc_large_node_hook mm/slub.c:1366 [inline] kmalloc_large_node mm/slub.c:3808 [inline] __kmalloc_node+0x100e/0x1290 mm/slub.c:3818 kmalloc_node include/linux/slab.h:554 [inline] kvmalloc_node+0x1a5/0x2e0 mm/util.c:419 kvmalloc include/linux/mm.h:541 [inline] vhost_net_open+0x64/0x5f0 drivers/vhost/net.c:921 misc_open+0x7b5/0x8b0 drivers/char/misc.c:154 chrdev_open+0xc28/0xd90 fs/char_dev.c:417 do_dentry_open+0xccb/0x1430 fs/open.c:752 vfs_open+0x272/0x2e0 fs/open.c:866 do_last fs/namei.c:3378 [inline] path_openat+0x49ad/0x6580 fs/namei.c:3519 do_filp_open+0x267/0x640 fs/namei.c:3553 do_sys_open+0x6ad/0x9c0 fs/open.c:1059 SYSC_openat+0xc7/0xe0 fs/open.c:1086 SyS_openat+0x63/0x90 fs/open.c:1080 do_syscall_64+0x2f1/0x450 arch/x86/entry/common.c:287 ================================================================== Fixes: c67df11f ("vhost_net: try batch dequing from skb array") Signed-off-by:
Alexander Potapenko <glider@google.com> Signed-off-by:
-
Kunihiko Hayashi authored
This enables AVE_GI_RXDROP interrupt factor. This factor indicates depletion of Rx descriptors and the handler counts the number of dropped packets. Signed-off-by:
Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Signed-off-by:
-
Daniel Axtens authored
As well as the basic conversion, I noticed that a lot of the SCTP code checks gso_type without first checking skb_is_gso() so I have added that where appropriate. Also, document the helper. Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by:
Daniel Axtens <dja@axtens.net> Signed-off-by:
-
Eric Dumazet authored
A tun device type can trivially be set to arbitrary value using TUNSETLINK ioctl(). Therefore, lowpan_device_event() must really check that ieee802154_ptr is not NULL. Fixes: 2c88b528 ("ieee802154: 6lowpan: remove check on null") Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Alexander Aring <alex.aring@gmail.com> Cc: Stefan Schmidt <stefan@osg.samsung.com> Reported-by:
syzbot <syzkaller@googlegroups.com> Acked-by:
Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by:
-
Lorenzo Bianconi authored
Fix the following slab-out-of-bounds kasan report in ndisc_fill_redirect_hdr_option when the incoming ipv6 packet is not linear and the accessed data are not in the linear data region of orig_skb. [ 1503.122508] ================================================================== [ 1503.122832] BUG: KASAN: slab-out-of-bounds in ndisc_send_redirect+0x94e/0x990 [ 1503.123036] Read of size 1184 at addr ffff8800298ab6b0 by task netperf/1932 [ 1503.123220] CPU: 0 PID: 1932 Comm: netperf Not tainted 4.16.0-rc2+ #124 [ 1503.123347] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.10.2-2.fc27 04/01/2014 [ 1503.123527] Call Trace: [ 1503.123579] <IRQ> [ 1503.123638] print_address_description+0x6e/0x280 [ 1503.123849] kasan_report+0x233/0x350 [ 1503.123946] memcpy+0x1f/0x50 [ 1503.124037] ndisc_send_redirect+0x94e/0x990 [ 1503.125150] ip6_forward+0x1242/0x13b0 [...] [ 1503.153890] Allocated by task 1932: [ 1503.153982] kasan_kmalloc+0x9f/0xd0 [ 1503.154074] __kmalloc_track_caller+0xb5/0x160 [ 1503.154198] __kmalloc_reserve.isra.41+0x24/0x70 [ 1503.154324] __alloc_skb+0x130/0x3e0 [ 1503.154415] sctp_packet_transmit+0x21a/0x1810 [ 1503.154533] sctp_outq_flush+0xc14/0x1db0 [ 1503.154624] sctp_do_sm+0x34e/0x2740 [ 1503.154715] sctp_primitive_SEND+0x57/0x70 [ 1503.154807] sctp_sendmsg+0xaa6/0x1b10 [ 1503.154897] sock_sendmsg+0x68/0x80 [ 1503.154987] ___sys_sendmsg+0x431/0x4b0 [ 1503.155078] __sys_sendmsg+0xa4/0x130 [ 1503.155168] do_syscall_64+0x171/0x3f0 [ 1503.155259] entry_SYSCALL_64_after_hwframe+0x42/0xb7 [ 1503.155436] Freed by task 1932: [ 1503.155527] __kasan_slab_free+0x134/0x180 [ 1503.155618] kfree+0xbc/0x180 [ 1503.155709] skb_release_data+0x27f/0x2c0 [ 1503.155800] consume_skb+0x94/0xe0 [ 1503.155889] sctp_chunk_put+0x1aa/0x1f0 [ 1503.155979] sctp_inq_pop+0x2f8/0x6e0 [ 1503.156070] sctp_assoc_bh_rcv+0x6a/0x230 [ 1503.156164] sctp_inq_push+0x117/0x150 [ 1503.156255] sctp_backlog_rcv+0xdf/0x4a0 [ 1503.156346] __release_sock+0x142/0x250 [ 1503.156436] release_sock+0x80/0x180 [ 1503.156526] sctp_sendmsg+0xbb0/0x1b10 [ 1503.156617] sock_sendmsg+0x68/0x80 [ 1503.156708] ___sys_sendmsg+0x431/0x4b0 [ 1503.156799] __sys_sendmsg+0xa4/0x130 [ 1503.156889] do_syscall_64+0x171/0x3f0 [ 1503.156980] entry_SYSCALL_64_after_hwframe+0x42/0xb7 [ 1503.157158] The buggy address belongs to the object at ffff8800298ab600 which belongs to the cache kmalloc-1024 of size 1024 [ 1503.157444] The buggy address is located 176 bytes inside of 1024-byte region [ffff8800298ab600, ffff8800298aba00) [ 1503.157702] The buggy address belongs to the page: [ 1503.157820] page:ffffea0000a62a00 count:1 mapcount:0 mapping:0000000000000000 index:0x0 compound_mapcount: 0 [ 1503.158053] flags: 0x4000000000008100(slab|head) [ 1503.158171] raw: 4000000000008100 0000000000000000 0000000000000000 00000001800e000e [ 1503.158350] raw: dead000000000100 dead000000000200 ffff880036002600 0000000000000000 [ 1503.158523] page dumped because: kasan: bad access detected [ 1503.158698] Memory state around the buggy address: [ 1503.158816] ffff8800298ab900: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 1503.158988] ffff8800298ab980: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 1503.159165] >ffff8800298aba00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [ 1503.159338] ^ [ 1503.159436] ffff8800298aba80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 1503.159610] ffff8800298abb00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 1503.159785] ================================================================== [ 1503.159964] Disabling lock debugging due to kernel taint The test scenario to trigger the issue consists of 4 devices: - H0: data sender, connected to LAN0 - H1: data receiver, connected to LAN1 - GW0 and GW1: routers between LAN0 and LAN1. Both of them have an ethernet connection on LAN0 and LAN1 On H{0,1} set GW0 as default gateway while on GW0 set GW1 as next hop for data from LAN0 to LAN1. Moreover create an ip6ip6 tunnel between H0 and H1 and send 3 concurrent data streams (TCP/UDP/SCTP) from H0 to H1 through ip6ip6 tunnel (send buffer size is set to 16K). While data streams are active flush the route cache on HA multiple times. I have not been able to identify a given commit that introduced the issue since, using the reproducer described above, the kasan report has been triggered from 4.14 and I have not gone back further. Reported-by:Jianlin Shi <jishi@redhat.com> Reviewed-by:
Stefano Brivio <sbrivio@redhat.com> Reviewed-by:
Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by:
-
- 08 Mar, 2018 9 commits
-
-
David S. Miller authored
Stephen Hemminger says: ==================== hv_netvsc: fix multicast flags and sync This set of patches deals with the handling of multicast flags and addresses in transparent VF mode. The recent set of patches (in linux-net) had a couple of bugs. ==================== Signed-off-by: -
Stephen Hemminger authored
The dev_uc/mc_sync calls need to have the device address list locked. This was spotted by running with lockdep enabled. Fixes: bee9d41b ("hv_netvsc: propagate rx filters to VF") Signed-off-by:
Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by:
-
Stephen Hemminger authored
The rx_mode operation handler is different than other callbacks in that is not always called with rtnl held. Therefore use RCU to ensure that references are valid. Fixes: bee9d41b ("hv_netvsc: propagate rx filters to VF") Signed-off-by:
-
Stephen Hemminger authored
The netvsc driver can get repeated calls to netvsc_rx_mode during network setup; each of these calls ends up scheduling the lower layers to update tha packet filter. This update requires an request/response to the host. So avoid doing this if we already know that the correct packet filter value is set. Signed-off-by:
-
Stephen Hemminger authored
The recent change to not always enable all multicast and broadcast was broken; meant to set filter, not change flags. Fixes: 009f766c ("hv_netvsc: filter multicast/broadcast") Signed-off-by:
-
David S. Miller authored
Merge tag 'wireless-drivers-for-davem-2018-03-08' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers Kalle Valo: ==================== wireless-drivers fixes for 4.16 Quote a few fixes as I have not been able to send a pull request earlier. Most of the fixes for iwlwifi but also few others, nothing really standing out though. iwlwifi * fix a bogus warning when freeing a TFD * fix severe throughput problem with 9000 series * fix for a bug that caused queue hangs in certain situations * fix for an issue with IBSS * fix an issue with rate-scaling in AP-mode * fix Channel Switch Announcement (CSA) issues with count 0 and 1 * some firmware debugging fixes * remov a wrong error message when removing keys * fix a firmware sysassert most usually triggered in IBSS * a couple of fixes on multicast queues * a fix with CCMP 256 rtlwifi * fix loss of signal for rtl8723be brcmfmac * add possibility to obtain firmware error * fix P2P_DEVICE ethernet address generation ==================== Signed-off-by:
-
Daniel Axtens authored
Pretty minor: just SKB_GSO_TCP -> SKB_GSO_TCPV4 and SKB_GSO_TCP6 -> SKB_GSO_TCPV6. Signed-off-by: -
Arkadi Sharshevsky authored
The __send_and_alloc_skb() receives a skb ptr as a parameter but in case it fails the skb is not valid: - Send failed and released the skb internally. - Allocation failed. The current code tries to release the skb in case of failure which causes redundant freeing. Fixes: 9b00cf2d ("team: implement multipart netlink messages for options transfers") Signed-off-by:
Arkadi Sharshevsky <arkadis@mellanox.com> Acked-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpfDavid S. Miller authored
Daniel Borkmann says: ==================== pull-request: bpf 2018-03-08 The following pull-request contains BPF updates for your *net* tree. The main changes are: 1) Fix various BPF helpers which adjust the skb and its GSO information with regards to SCTP GSO. The latter is a special case where gso_size is of value GSO_BY_FRAGS, so mangling that will end up corrupting the skb, thus bail out when seeing SCTP GSO packets, from Daniel(s). 2) Fix a compilation error in bpftool where BPF_FS_MAGIC is not defined due to too old kernel headers in the system, from Jiri. 3) Increase the number of x64 JIT passes in order to allow larger images to converge instead of punting them to interpreter or having them rejected when the interpreter is not built into the kernel, from Daniel. ==================== Signed-off-by:
-
- 07 Mar, 2018 9 commits
-
-
Daniel Borkmann authored
In Cilium some of the main programs we run today are hitting 9 passes on x64's JIT compiler, and we've had cases already where we surpassed the limit where the JIT then punts the program to the interpreter instead, leading to insertion failures due to CONFIG_BPF_JIT_ALWAYS_ON or insertion failures due to the prog array owner being JITed but the program to insert not (both must have the same JITed/non-JITed property). One concrete case the program image shrunk from 12,767 bytes down to 10,288 bytes where the image converged after 16 steps. I've measured that this took 340us in the JIT until it converges on my i7-6600U. Thus, increase the original limit we had from day one where the JIT covered cBPF only back then before we run into the case (as similar with the complexity limit) where we trip over this and hit program rejections. Also add a cond_resched() into the compilation loop, the JIT process runs without any locks and may sleep anyway. Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Acked-by:
Alexei Starovoitov <ast@kernel.org> Reviewed-by:
-
Ganesh Goudar authored
Do not set 'needs_free_netdev' as we do call free_netdev for mgmt net devices, doing both hits BUG_ON. Signed-off-by:
Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by:
-
Ganesh Goudar authored
instantiation of VF's on different adapters fails, copy adapter index and chip type to PF0-3 adapter instances to fix the issue. Signed-off-by:
-
Paul Moore authored
Starting with v4.16-rc1 we've been seeing a higher than usual number of requests for the kernel to load networking modules, even on events which shouldn't trigger a module load (e.g. ioctl(TCGETS)). Stephen Smalley suggested the problem may lie in commit 44c02a2c ("dev_ioctl(): move copyin/copyout to callers") which moves changes the network dev_ioctl() function to always call dev_load(), regardless of the requested ioctl. This patch moves the dev_load() calls back into the individual ioctls while preserving the rest of the original patch. Reported-by:
Dominick Grift <dac.override@gmail.com> Suggested-by:
Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by:
Paul Moore <paul@paul-moore.com> Signed-off-by:
-
Soheil Hassas Yeganeh authored
When the connection is aborted, there is no point in keeping the packets on the write queue until the connection is closed. Similar to a27fd7a8 ('tcp: purge write queue upon RST'), this is essential for a correct MSG_ZEROCOPY implementation, because userspace cannot call close(fd) before receiving zerocopy signals even when the connection is aborted. Fixes: f214f915 ("tcp: enable MSG_ZEROCOPY") Signed-off-by:
Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by:
Neal Cardwell <ncardwell@google.com> Reviewed-by:
Yuchung Cheng <ycheng@google.com> Signed-off-by:
-
Alexey Kodanev authored
dccp_disconnect() sets 'dp->dccps_hc_tx_ccid' tx handler to NULL, therefore if DCCP socket is disconnected and dccp_sendmsg() is called after it, it will cause a NULL pointer dereference in dccp_write_xmit(). This crash and the reproducer was reported by syzbot. Looks like it is reproduced if commit 69c64866 ("dccp: CVE-2017-8824: use-after-free in DCCP code") is applied. Reported-by: syzbot+f99ab3887ab65d70f816@syzkaller.appspotmail.com Signed-off-by:
-
Eric Dumazet authored
syzkaller found an issue caused by lack of sufficient checks in l2tp_tunnel_create() RAW sockets can not be considered as UDP ones for instance. In another patch, we shall replace all pr_err() by less intrusive pr_debug() so that syzkaller can find other bugs faster. Acked-by:
Guillaume Nault <g.nault@alphalink.fr> Acked-by:
James Chapman <jchapman@katalix.com> ================================================================== BUG: KASAN: slab-out-of-bounds in setup_udp_tunnel_sock+0x3ee/0x5f0 net/ipv4/udp_tunnel.c:69 dst_release: dst:00000000d53d0d0f refcnt:-1 Write of size 1 at addr ffff8801d013b798 by task syz-executor3/6242 CPU: 1 PID: 6242 Comm: syz-executor3 Not tainted 4.16.0-rc2+ #253 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:17 [inline] dump_stack+0x194/0x24d lib/dump_stack.c:53 print_address_description+0x73/0x250 mm/kasan/report.c:256 kasan_report_error mm/kasan/report.c:354 [inline] kasan_report+0x23b/0x360 mm/kasan/report.c:412 __asan_report_store1_noabort+0x17/0x20 mm/kasan/report.c:435 setup_udp_tunnel_sock+0x3ee/0x5f0 net/ipv4/udp_tunnel.c:69 l2tp_tunnel_create+0x1354/0x17f0 net/l2tp/l2tp_core.c:1596 pppol2tp_connect+0x14b1/0x1dd0 net/l2tp/l2tp_ppp.c:707 SYSC_connect+0x213/0x4a0 net/socket.c:1640 SyS_connect+0x24/0x30 net/socket.c:1621 do_syscall_64+0x280/0x940 arch/x86/entry/common.c:287 entry_SYSCALL_64_after_hwframe+0x42/0xb7 Fixes: fd558d18 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts") Signed-off-by:
-
Kirill Tkhai authored
inet_evict_bucket() iterates global list, and several tasks may call it in parallel. All of them hash the same fq->list_evictor to different lists, which leads to list corruption. This patch makes fq be hashed to expired list only if this has not been made yet by another task. Since inet_frag_alloc() allocates fq using kmem_cache_zalloc(), we may rely on list_evictor is initially unhashed. The problem seems to exist before async pernet_operations, as there was possible to have exit method to be executed in parallel with inet_frags::frags_work, so I add two Fixes tags. This also may go to stable. Fixes: d1fe1944 "inet: frag: don't re-use chainlist for evictor" Fixes: f84c6821 "net: Convert pernet_subsys, registered from inet_init()" Signed-off-by:
Kirill Tkhai <ktkhai@virtuozzo.com> Signed-off-by:
-
Jeremy Linton authored
The smsc911x driver will crash if it is rmmod'ed while the netdev is up like: Call trace: phy_detach+0x94/0x150 phy_disconnect+0x40/0x50 smsc911x_stop+0x104/0x128 [smsc911x] __dev_close_many+0xb4/0x138 dev_close_many+0xbc/0x190 rollback_registered_many+0x140/0x460 rollback_registered+0x68/0xb0 unregister_netdevice_queue+0x100/0x118 unregister_netdev+0x28/0x38 smsc911x_drv_remove+0x58/0x130 [smsc911x] platform_drv_remove+0x30/0x50 device_release_driver_internal+0x15c/0x1f8 driver_detach+0x54/0x98 bus_remove_driver+0x64/0xe8 driver_unregister+0x34/0x60 platform_driver_unregister+0x20/0x30 smsc911x_cleanup_module+0x14/0xbca8 [smsc911x] SyS_delete_module+0x1e8/0x238 __sys_trace_return+0x0/0x4 This is caused by the mdiobus being unregistered/free'd and the code in phy_detach() attempting to manipulate mdio related structures from unregister_netdev() calling close() To fix this, we delay the mdiobus teardown until after the netdev is deregistered. Reported-by:
Matt Sealey <matt.sealey@arm.com> Signed-off-by:
Jeremy Linton <jeremy.linton@arm.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
