Routing L3 multicast needs source-based routing.

With this built-in the following interface is created automatically:

    2: sit0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN mode DEFAULT group default qlen 1000
        link/sit 0.0.0.0 brd 0.0.0.0

remove it.

To be able to test multicast routing internals.

So that veth links outgoing from two different namespaces could be
connected together.

Needed to organize links in network namespaces.

This is the default NIC emulated by QEMU.

I don't use.

We have EXT4 which can work with both ext2 and ext3. Besides that I
don't use any ext filesystems currently as root under QEMU is mounted
over 9P.

There is no leds to control from under QEMU.

There is no backlight to control under QEMU.

We have VIRTIO_GPU to be used under QEMU.

QEMU does not support joysticks and I do not need it at all.

Under QEMU we have network support via VIRTIO_NET.

There is no need to load firmware under qemu.

No need to load CPU microcode under QEMU.

We are running "QEMU Virtual CPU", not Intel.

There is no possibility a virtual CPU could get overheaten on something
similar.

+ enable CUSE (this is needed to test OSSPD).

CONFIG_KASAN_STACK=1 is selected automatically on GCC:

	git.kernel.org/linus/6baec880d7

Debian's cpuburn was removed from the distribution.

  qemu_debug += BPF
  qemu_debug: `make oldconfig` on 5.0.0-rc6 + fuse+next (v5.0-rc6-25-gfabf7e0262d0)
  qemu_debug += FUSE
  qemu_debug: `make oldconfig` on 5.0.0-rc1 + fuse-next (fuse-fixes-5.0-rc6-25-ge057f7fc89c2)
  qemu_debug: `make oldconfig` on 4.19.0-rc5
  mini64(3.16): tun: m->y; sit=y->m; increase log buffer size
  mini64(3.16): sky2: m -> y
  mini64(3.16): Align more networking options with lab.nexedi.com backend
  mini64(3.16): Try to align IPv6 options with lab.nexedi.com backend
  mini64: Start 3.16.7-ckt20 config
  mini64: CONFIG_IPV6_SUBTREES=y  (to run re6st)
  mini64: CFG80211_WEXT=y
  mini64: Try to enable BRCMSMAC
  mini64: +ext4 +ipv6 +namespaces (and in particular +userns)
  mini64: Make oldconfig for v3.17.1
  mini64: CONFIG_FHANDLE=y
  qemu_debug: Turn on all virtio
  qemu_debug: Kernel runs under qemu and logs to serial console
  qemu_debug: Start from mini64.conf and oldconfig it for v3.17-rc1-22-g480cadc
  mini64: make oldconfig for ~ 3.16.0-rc7
  ...

To be able to use e.g. bpftrace.

To debug fuse itself.

Inspired by gendiff from RPM. Defaults to .nxd0 suffix but suffix can be
set explicitly. See details in script header how to use & make local
changes so gendiff-nxd0 works.

Иначе без модулей не работает сеть.

То, что было =m, не включал (и проверил 95%) что модули не загружены.
То, что было =y - включил.

The same one as using on lab.nexedi.com backend.

Currently only oldconfig-extracted from latest mini64.conf.
Will adjust in following commits.