-
Tom Zanussi authored
Original changelog from Steve Rostedt (except last sentence which explains the problem, and the Fixes: tag): I performed a three way histogram with the following commands: echo 'irq_lat u64 lat pid_t pid' > synthetic_events echo 'wake_lat u64 lat u64 irqlat pid_t pid' >> synthetic_events echo 'hist:keys=common_pid:irqts=common_timestamp.usecs if function == 0xffffffff81200580' > events/timer/hrtimer_start/trigger echo 'hist:keys=common_pid:lat=common_timestamp.usecs-$irqts:onmatch(timer.hrtimer_start).irq_lat($lat,pid) if common_flags & 1' > events/sched/sched_waking/trigger echo 'hist:keys=pid:wakets=common_timestamp.usecs,irqlat=lat' > events/synthetic/irq_lat/trigger echo 'hist:keys=next_pid:lat=common_timestamp.usecs-$wakets,irqlat=$irqlat:onmatch(synthetic.irq_lat).wake_lat($lat,$irqlat,next_pid)' > events/sched/sched_switch/trigger echo 1 > events/synthetic/wake_lat/enable Basically I wanted to see: hrtimer_start (calling function tick_sched_timer) Note: # grep tick_sched_timer /proc/kallsyms ffffffff81200580 t tick_sched_timer And save the time of that, and then record sched_waking if it is called in interrupt context and with the same pid as the hrtimer_start, it will record the latency between that and the waking event. I then look at when the task that is woken is scheduled in, and record the latency between the wakeup and the task running. At the end, the wake_lat synthetic event will show the wakeup to scheduled latency, as well as the irq latency in from hritmer_start to the wakeup. The problem is that I found this: <idle>-0 [007] d... 190.485261: wake_lat: lat=27 irqlat=190485230 pid=698 <idle>-0 [005] d... 190.485283: wake_lat: lat=40 irqlat=190485239 pid=10 <idle>-0 [002] d... 190.488327: wake_lat: lat=56 irqlat=190488266 pid=335 <idle>-0 [005] d... 190.489330: wake_lat: lat=64 irqlat=190489262 pid=10 <idle>-0 [003] d... 190.490312: wake_lat: lat=43 irqlat=190490265 pid=77 <idle>-0 [005] d... 190.493322: wake_lat: lat=54 irqlat=190493262 pid=10 <idle>-0 [005] d... 190.497305: wake_lat: lat=35 irqlat=190497267 pid=10 <idle>-0 [005] d... 190.501319: wake_lat: lat=50 irqlat=190501264 pid=10 The irqlat seemed quite large! Investigating this further, if I had enabled the irq_lat synthetic event, I noticed this: <idle>-0 [002] d.s. 249.429308: irq_lat: lat=164968 pid=335 <idle>-0 [002] d... 249.429369: wake_lat: lat=55 irqlat=249429308 pid=335 Notice that the timestamp of the irq_lat "249.429308" is awfully similar to the reported irqlat variable. In fact, all instances were like this. It appeared that: irqlat=$irqlat Wasn't assigning the old $irqlat to the new irqlat variable, but instead was assigning the $irqts to it. The issue is that assigning the old $irqlat to the new irqlat variable creates a variable reference alias, but the alias creation code forgets to make sure the alias uses the same var_ref_idx to access the reference. Link: http://lkml.kernel.org/r/1567375321.5282.12.camel@kernel.org Cc: Linux Trace Devel <linux-trace-devel@vger.kernel.org> Cc: linux-rt-users <linux-rt-users@vger.kernel.org> Cc: stable@vger.kernel.org Fixes: 7e8b88a3 ("tracing: Add hist trigger support for variable reference aliases") Reported-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by:
Tom Zanussi <zanussi@kernel.org> Signed-off-by:
Steven Rostedt (VMware) <rostedt@goodmis.org>
17f8607a