arm64: dts: meson: add libretech aml-s805x-ac board

Add Libretech aml-s805x-ac board (aka 'La Frite') support
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

arch/arm64/boot/dts/amlogic/Makefile

@@ -11,6 +11,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-vega-s95-meta.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-vega-s95-telos.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-wetek-hub.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-wetek-play2.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805x-libretech-ac.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-hwacom-amazetv.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-khadas-vim.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-libretech-cc.dtb

arch/arm64/boot/dts/amlogic/meson-gxl-s805x-libretech-ac.dts

+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2018 BayLibre, SAS.
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ * Author: Jerome Brunet <jbrunet@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+
+#include "meson-gxl-s905x.dtsi"
+
+/ {
+	compatible = "libretech,aml-s805x-ac", "amlogic,s805x",
+		     "amlogic,meson-gxl";
+	model = "Libre Computer Board AML-S805X-AC";
+
+	aliases {
+		serial0 = &uart_AO;
+		ethernet0 = &ethmac;
+		spi0 = &spifc;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	cvbs-connector {
+		/*
+		 * The pads are present but no connector is soldered on
+		 * 2J2, so keep this off by default.
+		 */
+		status = "disabled";
+		compatible = "composite-video-connector";
+
+		port {
+			cvbs_connector_in: endpoint {
+				remote-endpoint = <&cvbs_vdac_out>;
+			};
+		};
+	};
+
+	dc_5v: regulator-dc_5v {
+		compatible = "regulator-fixed";
+		regulator-name = "DC_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_tx_tmds_out>;
+			};
+		};
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x20000000>;
+	};
+
+	vcck: regulator-vcck {
+		compatible = "regulator-fixed";
+		regulator-name = "VCCK";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&dc_5v>;
+
+		/*
+		 * This is controlled by GPIOAO_9 we reserve this but
+		 * claiming it as done below reset the board anyway
+		 * Need to investigate this
+		 *
+		 * gpio = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>;
+		 * enable-active-high;
+		 */
+		regulator-always-on;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&dc_5v>;
+		regulator-always-on;
+	};
+
+	vddio_boot: regulator-vddio_boot {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_BOOT";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_3v3>;
+		regulator-always-on;
+	};
+};
+
+&cec_AO {
+	status = "okay";
+	pinctrl-0 = <&ao_cec_pins>;
+	pinctrl-names = "default";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&cvbs_vdac_port {
+	cvbs_vdac_out: endpoint {
+		remote-endpoint = <&cvbs_connector_in>;
+	};
+};
+
+&ethmac {
+	status = "okay";
+};
+
+&internal_phy {
+	pinctrl-0 = <&eth_link_led_pins>, <&eth_act_led_pins>;
+	pinctrl-names = "default";
+};
+
+&ir {
+	status = "okay";
+	pinctrl-0 = <&remote_input_ao_pins>;
+	pinctrl-names = "default";
+};
+
+&hdmi_tx {
+	status = "okay";
+	pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
+	pinctrl-names = "default";
+};
+
+&hdmi_tx_tmds_port {
+	hdmi_tx_tmds_out: endpoint {
+		remote-endpoint = <&hdmi_connector_in>;
+	};
+};
+
+&gpio_ao {
+	gpio-line-names = "UART TX",
+			  "UART RX",
+			  "7J1 Header Pin31",
+			  "", "", "", "",
+			  "IR In",
+			  "HDMI CEC",
+			  "5V VCCK Regulator",
+			  /* GPIO_TEST_N */
+			  "";
+};
+
+&gpio {
+	gpio-line-names = /* Bank GPIOZ */
+			  "", "", "", "", "", "", "",
+			  "", "", "", "", "", "", "",
+			  "Eth Link LED", "Eth Activity LED",
+			  /* Bank GPIOH */
+			  "HDMI HPD", "HDMI SDA", "HDMI SCL",
+			  "", "7J1 Header Pin13",
+			  "7J1 Header Pin15",
+			  "7J1 Header Pin7",
+			  "7J1 Header Pin12",
+			  "7J1 Header Pin16",
+			  "7J1 Header Pin18",
+			  /* Bank BOOT */
+			  "eMMC D0", "eMMC D1", "eMMC D2", "eMMC D3",
+			  "eMMC D4", "eMMC D5", "eMMC D6", "eMMC D7",
+			  "eMMC Clk", "eMMC Reset", "eMMC CMD",
+			  "SPI NOR MOSI", "SPI NOR MISO", "SPI NOR Clk",
+			  "", "SPI NOR Chip Select",
+			  /* Bank CARD */
+			  "", "", "", "", "", "", "",
+			  /* Bank GPIODV */
+			  "", "", "", "", "", "", "", "", "", "", "", "",
+			  "", "", "", "", "", "", "", "", "", "", "", "",
+			  "7J1 Header Pin27", "7J1 Header Pin28", "",
+			  "7J1 Header Pin29",
+			  "VCCK Regulator", "VDDEE Regulator",
+			  /* Bank GPIOX */
+			  "7J1 Header Pin22", "7J1 Header Pin26",
+			  "7J1 Header Pin36", "7J1 Header Pin38",
+			  "7J1 Header Pin40", "7J1 Header Pin37",
+			  "7J1 Header Pin33", "7J1 Header Pin35",
+			  "7J1 Header Pin19", "7J1 Header Pin21",
+			  "7J1 Header Pin24", "7J1 Header Pin23",
+			  "7J1 Header Pin8", "7J1 Header Pin10",
+			  "", "", "7J1 Header Pin32", "", "",
+			  /* Bank GPIOCLK */
+			  "", "";
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vddio_boot>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	max-frequency = <200000000>;
+	disable-wp;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+&spifc {
+	status = "okay";
+	pinctrl-0 = <&nor_pins>;
+	pinctrl-names = "default";
+
+	w25q32: spi-flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <3000000>;
+	};
+};
+
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&usb0 {
+	status = "okay";
+};