Merge branch 'ixp4-cleanup' into devel

arch/arm/mach-ixp4xx/common.c

@@ -81,6 +81,44 @@ void __init ixp4xx_map_io(void)
   	iotable_init(ixp4xx_io_desc, ARRAY_SIZE(ixp4xx_io_desc));
 }
 
+/*
+ * GPIO-functions
+ */
+/*
+ * The following converted to the real HW bits the gpio_line_config
+ */
+/* GPIO pin types */
+#define IXP4XX_GPIO_OUT 		0x1
+#define IXP4XX_GPIO_IN  		0x2
+
+/* GPIO signal types */
+#define IXP4XX_GPIO_LOW			0
+#define IXP4XX_GPIO_HIGH		1
+
+/* GPIO Clocks */
+#define IXP4XX_GPIO_CLK_0		14
+#define IXP4XX_GPIO_CLK_1		15
+
+static void gpio_line_config(u8 line, u32 direction)
+{
+	if (direction == IXP4XX_GPIO_IN)
+		*IXP4XX_GPIO_GPOER |= (1 << line);
+	else
+		*IXP4XX_GPIO_GPOER &= ~(1 << line);
+}
+
+static void gpio_line_get(u8 line, int *value)
+{
+	*value = (*IXP4XX_GPIO_GPINR >> line) & 0x1;
+}
+
+static void gpio_line_set(u8 line, int value)
+{
+	if (value == IXP4XX_GPIO_HIGH)
+	    *IXP4XX_GPIO_GPOUTR |= (1 << line);
+	else if (value == IXP4XX_GPIO_LOW)
+	    *IXP4XX_GPIO_GPOUTR &= ~(1 << line);
+}
 
 /*************************************************************************
  * IXP4xx chipset IRQ handling
@@ -117,17 +155,6 @@ static int ixp4xx_gpio_to_irq(struct gpio_chip *chip, unsigned gpio)
 	return -EINVAL;
 }
 
-int irq_to_gpio(unsigned int irq)
-{
-	int gpio = (irq < 32) ? irq2gpio[irq] : -EINVAL;
-
-	if (gpio == -1)
-		return -EINVAL;
-
-	return gpio;
-}
-EXPORT_SYMBOL(irq_to_gpio);
-
 static int ixp4xx_set_irq_type(struct irq_data *d, unsigned int type)
 {
 	int line = irq2gpio[d->irq];

arch/arm/mach-ixp4xx/dsmg600-setup.c

@@ -26,6 +26,7 @@
 #include <linux/reboot.h>
 #include <linux/i2c.h>
 #include <linux/i2c-gpio.h>
+#include <linux/gpio.h>
 
 #include <mach/hardware.h>
 
@@ -161,11 +162,8 @@ static struct platform_device *dsmg600_devices[] __initdata = {
 
 static void dsmg600_power_off(void)
 {
-	/* enable the pwr cntl gpio */
-	gpio_line_config(DSMG600_PO_GPIO, IXP4XX_GPIO_OUT);
-
-	/* poweroff */
-	gpio_line_set(DSMG600_PO_GPIO, IXP4XX_GPIO_HIGH);
+	/* enable the pwr cntl and drive it high */
+	gpio_direction_output(DSMG600_PO_GPIO, 1);
 }
 
 /* This is used to make sure the power-button pusher is serious.  The button
@@ -202,7 +200,7 @@ static void dsmg600_power_handler(unsigned long data)
 			ctrl_alt_del();
 
 			/* Change the state of the power LED to "blink" */
-			gpio_line_set(DSMG600_LED_PWR_GPIO, IXP4XX_GPIO_LOW);
+			gpio_set_value(DSMG600_LED_PWR_GPIO, 0);
 		} else {
 			power_button_countdown = PBUTTON_HOLDDOWN_COUNT;
 		}
@@ -228,6 +226,40 @@ static void __init dsmg600_timer_init(void)
     ixp4xx_timer_init();
 }
 
+static int __init dsmg600_gpio_init(void)
+{
+	if (!machine_is_dsmg600())
+		return 0;
+
+	gpio_request(DSMG600_RB_GPIO, "reset button");
+	if (request_irq(gpio_to_irq(DSMG600_RB_GPIO), &dsmg600_reset_handler,
+		IRQF_DISABLED | IRQF_TRIGGER_LOW,
+		"DSM-G600 reset button", NULL) < 0) {
+
+		printk(KERN_DEBUG "Reset Button IRQ %d not available\n",
+			gpio_to_irq(DSMG600_RB_GPIO));
+	}
+
+	/*
+	 * The power button on the D-Link DSM-G600 is on GPIO 15, but
+	 * it cannot handle interrupts on that GPIO line.  So we'll
+	 * have to poll it with a kernel timer.
+	 */
+
+	/* Make sure that the power button GPIO is set up as an input */
+	gpio_request(DSMG600_PB_GPIO, "power button");
+	gpio_direction_input(DSMG600_PB_GPIO);
+	/* Request poweroff GPIO line */
+	gpio_request(DSMG600_PO_GPIO, "power off button");
+
+	/* Set the initial value for the power button IRQ handler */
+	power_button_countdown = PBUTTON_HOLDDOWN_COUNT;
+
+	mod_timer(&dsmg600_power_timer, jiffies + msecs_to_jiffies(500));
+	return 0;
+}
+device_initcall(dsmg600_gpio_init);
+
 static void __init dsmg600_init(void)
 {
 	ixp4xx_sys_init();
@@ -251,27 +283,6 @@ static void __init dsmg600_init(void)
 	platform_add_devices(dsmg600_devices, ARRAY_SIZE(dsmg600_devices));
 
 	pm_power_off = dsmg600_power_off;
-
-	if (request_irq(gpio_to_irq(DSMG600_RB_GPIO), &dsmg600_reset_handler,
-		IRQF_DISABLED | IRQF_TRIGGER_LOW,
-		"DSM-G600 reset button", NULL) < 0) {
-
-		printk(KERN_DEBUG "Reset Button IRQ %d not available\n",
-			gpio_to_irq(DSMG600_RB_GPIO));
-	}
-
-	/* The power button on the D-Link DSM-G600 is on GPIO 15, but
-	 * it cannot handle interrupts on that GPIO line.  So we'll
-	 * have to poll it with a kernel timer.
-	 */
-
-	/* Make sure that the power button GPIO is set up as an input */
-	gpio_line_config(DSMG600_PB_GPIO, IXP4XX_GPIO_IN);
-
-	/* Set the initial value for the power button IRQ handler */
-	power_button_countdown = PBUTTON_HOLDDOWN_COUNT;
-
-	mod_timer(&dsmg600_power_timer, jiffies + msecs_to_jiffies(500));
 }
 
 MACHINE_START(DSMG600, "D-Link DSM-G600 RevA")

arch/arm/mach-ixp4xx/include/mach/platform.h

@@ -131,44 +131,5 @@ struct pci_sys_data;
 extern int ixp4xx_setup(int nr, struct pci_sys_data *sys);
 extern struct pci_ops ixp4xx_ops;
 
-/*
- * GPIO-functions
- */
-/*
- * The following converted to the real HW bits the gpio_line_config
- */
-/* GPIO pin types */
-#define IXP4XX_GPIO_OUT 		0x1
-#define IXP4XX_GPIO_IN  		0x2
-
-/* GPIO signal types */
-#define IXP4XX_GPIO_LOW			0
-#define IXP4XX_GPIO_HIGH		1
-
-/* GPIO Clocks */
-#define IXP4XX_GPIO_CLK_0		14
-#define IXP4XX_GPIO_CLK_1		15
-
-static inline void gpio_line_config(u8 line, u32 direction)
-{
-	if (direction == IXP4XX_GPIO_IN)
-		*IXP4XX_GPIO_GPOER |= (1 << line);
-	else
-		*IXP4XX_GPIO_GPOER &= ~(1 << line);
-}
-
-static inline void gpio_line_get(u8 line, int *value)
-{
-	*value = (*IXP4XX_GPIO_GPINR >> line) & 0x1;
-}
-
-static inline void gpio_line_set(u8 line, int value)
-{
-	if (value == IXP4XX_GPIO_HIGH)
-	    *IXP4XX_GPIO_GPOUTR |= (1 << line);
-	else if (value == IXP4XX_GPIO_LOW)
-	    *IXP4XX_GPIO_GPOUTR &= ~(1 << line);
-}
-
 #endif // __ASSEMBLY__
 

arch/arm/mach-ixp4xx/ixdp425-setup.c

@@ -20,6 +20,7 @@
 #include <linux/mtd/nand.h>
 #include <linux/mtd/partitions.h>
 #include <linux/delay.h>
+#include <linux/gpio.h>
 #include <asm/types.h>
 #include <asm/setup.h>
 #include <asm/memory.h>
@@ -80,10 +81,10 @@ ixdp425_flash_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl)
 
 	if (ctrl & NAND_CTRL_CHANGE) {
 		if (ctrl & NAND_NCE) {
-			gpio_line_set(IXDP425_NAND_NCE_PIN, IXP4XX_GPIO_LOW);
+			gpio_set_value(IXDP425_NAND_NCE_PIN, 0);
 			udelay(5);
 		} else
-			gpio_line_set(IXDP425_NAND_NCE_PIN, IXP4XX_GPIO_HIGH);
+			gpio_set_value(IXDP425_NAND_NCE_PIN, 1);
 
 		offset = (ctrl & NAND_CLE) ? IXDP425_NAND_CMD_BYTE : 0;
 		offset |= (ctrl & NAND_ALE) ? IXDP425_NAND_ADDR_BYTE : 0;
@@ -227,7 +228,8 @@ static void __init ixdp425_init(void)
 	ixdp425_flash_nand_resource.start = IXP4XX_EXP_BUS_BASE(3),
 	ixdp425_flash_nand_resource.end   = IXP4XX_EXP_BUS_BASE(3) + 0x10 - 1;
 
-	gpio_line_config(IXDP425_NAND_NCE_PIN, IXP4XX_GPIO_OUT);
+	gpio_request(IXDP425_NAND_NCE_PIN, "NAND NCE pin");
+	gpio_direction_output(IXDP425_NAND_NCE_PIN, 0);
 
 	/* Configure expansion bus for NAND Flash */
 	*IXP4XX_EXP_CS3 = IXP4XX_EXP_BUS_CS_EN |

arch/arm/mach-ixp4xx/nas100d-setup.c

@@ -184,11 +184,8 @@ static void nas100d_power_off(void)
 {
 	/* This causes the box to drop the power and go dead. */
 
-	/* enable the pwr cntl gpio */
-	gpio_line_config(NAS100D_PO_GPIO, IXP4XX_GPIO_OUT);
-
-	/* do the deed */
-	gpio_line_set(NAS100D_PO_GPIO, IXP4XX_GPIO_HIGH);
+	/* enable the pwr cntl gpio and assert power off */
+	gpio_direction_output(NAS100D_PO_GPIO, 1);
 }
 
 /* This is used to make sure the power-button pusher is serious.  The button
@@ -225,7 +222,7 @@ static void nas100d_power_handler(unsigned long data)
 			ctrl_alt_del();
 
 			/* Change the state of the power LED to "blink" */
-			gpio_line_set(NAS100D_LED_PWR_GPIO, IXP4XX_GPIO_LOW);
+			gpio_set_value(NAS100D_LED_PWR_GPIO, 0);
 		} else {
 			power_button_countdown = PBUTTON_HOLDDOWN_COUNT;
 		}
@@ -242,6 +239,33 @@ static irqreturn_t nas100d_reset_handler(int irq, void *dev_id)
 	return IRQ_HANDLED;
 }
 
+static int __init nas100d_gpio_init(void)
+{
+	if (!machine_is_nas100d())
+		return 0;
+
+	/*
+	 * The power button on the Iomega NAS100d is on GPIO 14, but
+	 * it cannot handle interrupts on that GPIO line.  So we'll
+	 * have to poll it with a kernel timer.
+	 */
+
+	/* Request the power off GPIO */
+	gpio_request(NAS100D_PO_GPIO, "power off");
+
+	/* Make sure that the power button GPIO is set up as an input */
+	gpio_request(NAS100D_PB_GPIO, "power button");
+	gpio_direction_input(NAS100D_PB_GPIO);
+
+	/* Set the initial value for the power button IRQ handler */
+	power_button_countdown = PBUTTON_HOLDDOWN_COUNT;
+
+	mod_timer(&nas100d_power_timer, jiffies + msecs_to_jiffies(500));
+
+	return 0;
+}
+device_initcall(nas100d_gpio_init);
+
 static void __init nas100d_init(void)
 {
 	uint8_t __iomem *f;
@@ -278,19 +302,6 @@ static void __init nas100d_init(void)
 			gpio_to_irq(NAS100D_RB_GPIO));
 	}
 
-	/* The power button on the Iomega NAS100d is on GPIO 14, but
-	 * it cannot handle interrupts on that GPIO line.  So we'll
-	 * have to poll it with a kernel timer.
-	 */
-
-	/* Make sure that the power button GPIO is set up as an input */
-	gpio_line_config(NAS100D_PB_GPIO, IXP4XX_GPIO_IN);
-
-	/* Set the initial value for the power button IRQ handler */
-	power_button_countdown = PBUTTON_HOLDDOWN_COUNT;
-
-	mod_timer(&nas100d_power_timer, jiffies + msecs_to_jiffies(500));
-
 	/*
 	 * Map in a portion of the flash and read the MAC address.
 	 * Since it is stored in BE in the flash itself, we need to

arch/arm/mach-ixp4xx/nslu2-setup.c

@@ -197,11 +197,8 @@ static void nslu2_power_off(void)
 {
 	/* This causes the box to drop the power and go dead. */
 
-	/* enable the pwr cntl gpio */
-	gpio_line_config(NSLU2_PO_GPIO, IXP4XX_GPIO_OUT);
-
-	/* do the deed */
-	gpio_line_set(NSLU2_PO_GPIO, IXP4XX_GPIO_HIGH);
+	/* enable the pwr cntl gpio and assert power off */
+	gpio_direction_output(NSLU2_PO_GPIO, 1);
 }
 
 static irqreturn_t nslu2_power_handler(int irq, void *dev_id)
@@ -223,6 +220,16 @@ static irqreturn_t nslu2_reset_handler(int irq, void *dev_id)
 	return IRQ_HANDLED;
 }
 
+static int __init nslu2_gpio_init(void)
+{
+	if (!machine_is_nslu2())
+		return 0;
+
+	/* Request the power off GPIO */
+	return gpio_request(NSLU2_PO_GPIO, "power off");
+}
+device_initcall(nslu2_gpio_init);
+
 static void __init nslu2_timer_init(void)
 {
     /* The xtal on this machine is non-standard. */

drivers/input/misc/ixp4xx-beeper.c

@@ -20,6 +20,7 @@
 #include <linux/delay.h>
 #include <linux/platform_device.h>
 #include <linux/interrupt.h>
+#include <linux/gpio.h>
 #include <mach/hardware.h>
 
 MODULE_AUTHOR("Alessandro Zummo <a.zummo@towertech.it>");
@@ -35,15 +36,12 @@ static void ixp4xx_spkr_control(unsigned int pin, unsigned int count)
 
 	spin_lock_irqsave(&beep_lock, flags);
 
-	 if (count) {
-		gpio_line_config(pin, IXP4XX_GPIO_OUT);
-		gpio_line_set(pin, IXP4XX_GPIO_LOW);
-
+	if (count) {
+		gpio_direction_output(pin, 0);
 		*IXP4XX_OSRT2 = (count & ~IXP4XX_OST_RELOAD_MASK) | IXP4XX_OST_ENABLE;
 	} else {
-		gpio_line_config(pin, IXP4XX_GPIO_IN);
-		gpio_line_set(pin, IXP4XX_GPIO_HIGH);
-
+		gpio_direction_output(pin, 1);
+		gpio_direction_input(pin);
 		*IXP4XX_OSRT2 = 0;
 	}
 
@@ -78,11 +76,13 @@ static int ixp4xx_spkr_event(struct input_dev *dev, unsigned int type, unsigned
 
 static irqreturn_t ixp4xx_spkr_interrupt(int irq, void *dev_id)
 {
+	unsigned int pin = (unsigned int) dev_id;
+
 	/* clear interrupt */
 	*IXP4XX_OSST = IXP4XX_OSST_TIMER_2_PEND;
 
 	/* flip the beeper output */
-	*IXP4XX_GPIO_GPOUTR ^= (1 << (unsigned int) dev_id);
+	gpio_set_value(pin, !gpio_get_value(pin));
 
 	return IRQ_HANDLED;
 }
@@ -110,11 +110,15 @@ static int ixp4xx_spkr_probe(struct platform_device *dev)
 	input_dev->sndbit[0] = BIT_MASK(SND_BELL) | BIT_MASK(SND_TONE);
 	input_dev->event = ixp4xx_spkr_event;
 
+	err = gpio_request(dev->id, "ixp4-beeper");
+	if (err)
+		goto err_free_device;
+
 	err = request_irq(IRQ_IXP4XX_TIMER2, &ixp4xx_spkr_interrupt,
 			  IRQF_NO_SUSPEND, "ixp4xx-beeper",
 			  (void *) dev->id);
 	if (err)
-		goto err_free_device;
+		goto err_free_gpio;
 
 	err = input_register_device(input_dev);
 	if (err)
@@ -126,6 +130,8 @@ static int ixp4xx_spkr_probe(struct platform_device *dev)
 
  err_free_irq:
 	free_irq(IRQ_IXP4XX_TIMER2, (void *)dev->id);
+ err_free_gpio:
+	gpio_free(dev->id);
  err_free_device:
 	input_free_device(input_dev);
 
@@ -144,6 +150,7 @@ static int ixp4xx_spkr_remove(struct platform_device *dev)
 	ixp4xx_spkr_control(pin, 0);
 
 	free_irq(IRQ_IXP4XX_TIMER2, (void *)dev->id);
+	gpio_free(dev->id);
 
 	return 0;
 }

drivers/ptp/ptp_ixp46x.c

@@ -259,8 +259,15 @@ static struct ixp_clock ixp_clock;
 static int setup_interrupt(int gpio)
 {
 	int irq;
+	int err;
 
-	gpio_line_config(gpio, IXP4XX_GPIO_IN);
+	err = gpio_request(gpio, "ixp4-ptp");
+	if (err)
+		return err;
+
+	err = gpio_direction_input(gpio);
+	if (err)
+		return err;
 
 	irq = gpio_to_irq(gpio);
 

drivers/staging/media/lirc/lirc_serial.c

@@ -67,7 +67,7 @@
 #include <linux/delay.h>
 #include <linux/poll.h>
 #include <linux/platform_device.h>
-
+#include <linux/gpio.h>
 #include <linux/io.h>
 #include <linux/irq.h>
 #include <linux/fcntl.h>
@@ -321,7 +321,7 @@ static void on(void)
 	 * status LED and ground
 	 */
 	if (type == LIRC_NSLU2) {
-		gpio_line_set(NSLU2_LED_GRN, IXP4XX_GPIO_LOW);
+		gpio_set_value(NSLU2_LED_GRN, 0);
 		return;
 	}
 #endif
@@ -335,7 +335,7 @@ static void off(void)
 {
 #ifdef CONFIG_LIRC_SERIAL_NSLU2
 	if (type == LIRC_NSLU2) {
-		gpio_line_set(NSLU2_LED_GRN, IXP4XX_GPIO_HIGH);
+		gpio_set_value(NSLU2_LED_GRN, 1);
 		return;
 	}
 #endif
@@ -839,6 +839,16 @@ static int lirc_serial_probe(struct platform_device *dev)
 {
 	int i, nlow, nhigh, result;
 
+#ifdef CONFIG_LIRC_SERIAL_NSLU2
+	/* This GPIO is used for a LED on the NSLU2 */
+	result = devm_gpio_request(dev, NSLU2_LED_GRN, "lirc-serial");
+	if (result)
+		return result;
+	result = gpio_direction_output(NSLU2_LED_GRN, 0);
+	if (result)
+		return result;
+#endif
+
 	result = request_irq(irq, irq_handler,
 			     (share_irq ? IRQF_SHARED : 0),
 			     LIRC_DRIVER_NAME, (void *)&hardware);