arm64: dts: khadas-vim3: add commented support for PCIe

The VIM3 on-board  MCU can mux the PCIe/USB3.0 shared differential
lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
an USB3.0 Type A connector and a M.2 Key M slot.
The PHY driving these differential lines is shared between
the USB3.0 controller and the PCIe Controller, thus only
a single controller can use it.

The needed DT configuration when the MCU is configured to mux
the PCIe/USB3.0 differential lines to the M.2 Key M slot is
added commented and may be uncommented to disable USB3.0 from the
USB Complex and enable the PCIe controller.

The End User is not expected to uncomment the following except for
testing purposes, but instead rely on the firmware/bootloader to
update these nodes accordingly if PCIe mode is selected by the MCU.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

arch/arm64/boot/dts/amlogic/meson-g12b-a311d-khadas-vim3.dts

@@ -14,3 +14,28 @@
 / {
 	compatible = "khadas,vim3", "amlogic,a311d", "amlogic,g12b";
 };
+
+/*
+ * The VIM3 on-board  MCU can mux the PCIe/USB3.0 shared differential
+ * lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
+ * an USB3.0 Type A connector and a M.2 Key M slot.
+ * The PHY driving these differential lines is shared between
+ * the USB3.0 controller and the PCIe Controller, thus only
+ * a single controller can use it.
+ * If the MCU is configured to mux the PCIe/USB3.0 differential lines
+ * to the M.2 Key M slot, uncomment the following block to disable
+ * USB3.0 from the USB Complex and enable the PCIe controller.
+ * The End User is not expected to uncomment the following except for
+ * testing purposes, but instead rely on the firmware/bootloader to
+ * update these nodes accordingly if PCIe mode is selected by the MCU.
+ */
+/*
+&pcie {
+	status = "okay";
+};
+
+&usb {
+	phys = <&usb2_phy0>, <&usb2_phy1>;
+	phy-names = "usb2-phy0", "usb2-phy1";
+};
+ */

arch/arm64/boot/dts/amlogic/meson-g12b-s922x-khadas-vim3.dts

@@ -14,3 +14,28 @@
 / {
 	compatible = "khadas,vim3", "amlogic,s922x", "amlogic,g12b";
 };
+
+/*
+ * The VIM3 on-board  MCU can mux the PCIe/USB3.0 shared differential
+ * lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
+ * an USB3.0 Type A connector and a M.2 Key M slot.
+ * The PHY driving these differential lines is shared between
+ * the USB3.0 controller and the PCIe Controller, thus only
+ * a single controller can use it.
+ * If the MCU is configured to mux the PCIe/USB3.0 differential lines
+ * to the M.2 Key M slot, uncomment the following block to disable
+ * USB3.0 from the USB Complex and enable the PCIe controller.
+ * The End User is not expected to uncomment the following except for
+ * testing purposes, but instead rely on the firmware/bootloader to
+ * update these nodes accordingly if PCIe mode is selected by the MCU.
+ */
+/*
+&pcie {
+	status = "okay";
+};
+
+&usb {
+	phys = <&usb2_phy0>, <&usb2_phy1>;
+	phy-names = "usb2-phy0", "usb2-phy1";
+};
+ */

arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi

@@ -246,6 +246,10 @@ &ir {
 	linux,rc-map-name = "rc-khadas";
 };
 
+&pcie {
+	reset-gpios = <&gpio GPIOA_8 GPIO_ACTIVE_LOW>;
+};
+
 &pwm_ef {
         status = "okay";
         pinctrl-0 = <&pwm_e_pins>;

arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts

@@ -68,3 +68,28 @@ &pwm_AO_cd {
 	clock-names = "clkin1";
 	status = "okay";
 };
+
+/*
+ * The VIM3 on-board  MCU can mux the PCIe/USB3.0 shared differential
+ * lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
+ * an USB3.0 Type A connector and a M.2 Key M slot.
+ * The PHY driving these differential lines is shared between
+ * the USB3.0 controller and the PCIe Controller, thus only
+ * a single controller can use it.
+ * If the MCU is configured to mux the PCIe/USB3.0 differential lines
+ * to the M.2 Key M slot, uncomment the following block to disable
+ * USB3.0 from the USB Complex and enable the PCIe controller.
+ * The End User is not expected to uncomment the following except for
+ * testing purposes, but instead rely on the firmware/bootloader to
+ * update these nodes accordingly if PCIe mode is selected by the MCU.
+ */
+/*
+&pcie {
+	status = "okay";
+};
+
+&usb {
+	phys = <&usb2_phy0>, <&usb2_phy1>;
+	phy-names = "usb2-phy0", "usb2-phy1";
+};
+ */