Commit 09f380e3 authored by Jernej Skrabec's avatar Jernej Skrabec Committed by Maxime Ripard

drm/sun4i: Don't change clock bits in DW HDMI PHY driver

DW HDMI PHY driver and PHY clock driver share same registers. Make sure
that DW HDMI PHY setup code doesn't change any clock related bits.
During initialization, set PHY PLL parent bit to 0.
Signed-off-by: default avatarJernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: default avatarMaxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-18-jernej.skrabec@siol.net
parent 09773c53
......@@ -98,7 +98,7 @@
#define SUN8I_HDMI_PHY_PLL_CFG1_LDO2_EN BIT(29)
#define SUN8I_HDMI_PHY_PLL_CFG1_LDO1_EN BIT(28)
#define SUN8I_HDMI_PHY_PLL_CFG1_HV_IS_33 BIT(27)
#define SUN8I_HDMI_PHY_PLL_CFG1_CKIN_SEL BIT(26)
#define SUN8I_HDMI_PHY_PLL_CFG1_CKIN_SEL_MSK BIT(26)
#define SUN8I_HDMI_PHY_PLL_CFG1_PLLEN BIT(25)
#define SUN8I_HDMI_PHY_PLL_CFG1_LDO_VSET(x) ((x) << 22)
#define SUN8I_HDMI_PHY_PLL_CFG1_UNKNOWN(x) ((x) << 20)
......
......@@ -183,7 +183,13 @@ static int sun8i_hdmi_phy_config_h3(struct dw_hdmi *hdmi,
regmap_update_bits(phy->regs, SUN8I_HDMI_PHY_ANA_CFG1_REG,
SUN8I_HDMI_PHY_ANA_CFG1_TXEN_MASK, 0);
regmap_write(phy->regs, SUN8I_HDMI_PHY_PLL_CFG1_REG, pll_cfg1_init);
/*
* NOTE: We have to be careful not to overwrite PHY parent
* clock selection bit and clock divider.
*/
regmap_update_bits(phy->regs, SUN8I_HDMI_PHY_PLL_CFG1_REG,
(u32)~SUN8I_HDMI_PHY_PLL_CFG1_CKIN_SEL_MSK,
pll_cfg1_init);
regmap_update_bits(phy->regs, SUN8I_HDMI_PHY_PLL_CFG2_REG,
(u32)~SUN8I_HDMI_PHY_PLL_CFG2_PREDIV_MSK,
pll_cfg2_init);
......@@ -352,6 +358,10 @@ static void sun8i_hdmi_phy_init_h3(struct sun8i_hdmi_phy *phy)
SUN8I_HDMI_PHY_ANA_CFG3_SCLEN |
SUN8I_HDMI_PHY_ANA_CFG3_SDAEN);
/* reset PHY PLL clock parent */
regmap_update_bits(phy->regs, SUN8I_HDMI_PHY_PLL_CFG1_REG,
SUN8I_HDMI_PHY_PLL_CFG1_CKIN_SEL_MSK, 0);
/* set HW control of CEC pins */
regmap_write(phy->regs, SUN8I_HDMI_PHY_CEC_REG, 0);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment