Commit 1077682b authored by Linus Torvalds's avatar Linus Torvalds

Merge master.kernel.org:/home/rmk/linux-2.6-arm

parents dc9ca2af bafa49cc
......@@ -7,7 +7,8 @@
* so we have to figure out the machine for ourselves...
*
* Support for Poodle, Corgi (SL-C700), Shepherd (SL-C750)
* and Husky (SL-C760).
* Husky (SL-C760), Tosa (SL-C6000), Spitz (SL-C3000),
* Akita (SL-C1000) and Borzoi (SL-C3100).
*
*/
......@@ -23,6 +24,22 @@
__SharpSL_start:
/* Check for TC6393 - if found we have a Tosa */
ldr r7, .TOSAID
mov r1, #0x10000000 @ Base address of TC6393 chip
mov r6, #0x03
ldrh r3, [r1, #8] @ Load TC6393XB Revison: This is 0x0003
cmp r6, r3
beq .SHARPEND @ Success -> tosa
/* Check for pxa270 - if found, branch */
mrc p15, 0, r4, c0, c0 @ Get Processor ID
and r4, r4, #0xffffff00
ldr r3, .PXA270ID
cmp r4, r3
beq .PXA270
/* Check for w100 - if not found we have a Poodle */
ldr r1, .W100ADDR @ Base address of w100 chip + regs offset
mov r6, #0x31 @ Load Magic Init value
......@@ -30,7 +47,7 @@ __SharpSL_start:
mov r5, #0x3000
.W100LOOP:
subs r5, r5, #1
bne .W100LOOP
bne .W100LOOP
mov r6, #0x30 @ Load 2nd Magic Init value
str r6, [r1, #0x280] @ to SCRATCH_UMSK
......@@ -40,45 +57,52 @@ __SharpSL_start:
cmp r6, r3
bne .SHARPEND @ We have no w100 - Poodle
mrc p15, 0, r6, c0, c0 @ Get Processor ID
and r6, r6, #0xffffff00
/* Check for pxa250 - if found we have a Corgi */
ldr r7, .CORGIID
ldr r3, .PXA255ID
cmp r6, r3
cmp r4, r3
blo .SHARPEND @ We have a PXA250 - Corgi
mov r1, #0x0c000000 @ Base address of NAND chip
ldrb r3, [r1, #24] @ Load FLASHCTL
bic r3, r3, #0x11 @ SET NCE
orr r3, r3, #0x0a @ SET CLR + FLWP
strb r3, [r1, #24] @ Save to FLASHCTL
mov r2, #0x90 @ Command "readid"
strb r2, [r1, #20] @ Save to FLASHIO
bic r3, r3, #2 @ CLR CLE
orr r3, r3, #4 @ SET ALE
strb r3, [r1, #24] @ Save to FLASHCTL
mov r2, #0 @ Address 0x00
strb r2, [r1, #20] @ Save to FLASHIO
bic r3, r3, #4 @ CLR ALE
strb r3, [r1, #24] @ Save to FLASHCTL
.SHARP1:
ldrb r3, [r1, #24] @ Load FLASHCTL
tst r3, #32 @ Is chip ready?
beq .SHARP1
ldrb r2, [r1, #20] @ NAND Manufacturer ID
ldrb r3, [r1, #20] @ NAND Chip ID
/* Check for 64MiB flash - if found we have a Shepherd */
bl get_flash_ids
ldr r7, .SHEPHERDID
cmp r3, #0x76 @ 64MiB flash
beq .SHARPEND @ We have Shepherd
/* Must be a Husky */
ldr r7, .HUSKYID @ Must be Husky
b .SHARPEND
.PXA270:
/* Check for 16MiB flash - if found we have Spitz */
bl get_flash_ids
ldr r7, .SPITZID
cmp r3, #0x73 @ 16MiB flash
beq .SHARPEND @ We have Spitz
/* Check for a second SCOOP chip - if found we have Borzoi */
ldr r1, .SCOOP2ADDR
ldr r7, .BORZOIID
mov r6, #0x0140
strh r6, [r1]
ldrh r6, [r1]
cmp r6, #0x0140
beq .SHARPEND @ We have Borzoi
/* Must be Akita */
ldr r7, .AKITAID
b .SHARPEND @ We have Borzoi
.PXA255ID:
.word 0x69052d00 @ PXA255 Processor ID
.PXA270ID:
.word 0x69054100 @ PXA270 Processor ID
.W100ID:
.word 0x57411002 @ w100 Chip ID
.W100ADDR:
.word 0x08010000 @ w100 Chip ID Reg Address
.SCOOP2ADDR:
.word 0x08800040
.POODLEID:
.word MACH_TYPE_POODLE
.CORGIID:
......@@ -87,6 +111,41 @@ __SharpSL_start:
.word MACH_TYPE_SHEPHERD
.HUSKYID:
.word MACH_TYPE_HUSKY
.SHARPEND:
.TOSAID:
.word MACH_TYPE_TOSA
.SPITZID:
.word MACH_TYPE_SPITZ
.AKITAID:
.word MACH_TYPE_AKITA
.BORZOIID:
.word MACH_TYPE_BORZOI
/*
* Return: r2 - NAND Manufacturer ID
* r3 - NAND Chip ID
* Corrupts: r1
*/
get_flash_ids:
mov r1, #0x0c000000 @ Base address of NAND chip
ldrb r3, [r1, #24] @ Load FLASHCTL
bic r3, r3, #0x11 @ SET NCE
orr r3, r3, #0x0a @ SET CLR + FLWP
strb r3, [r1, #24] @ Save to FLASHCTL
mov r2, #0x90 @ Command "readid"
strb r2, [r1, #20] @ Save to FLASHIO
bic r3, r3, #2 @ CLR CLE
orr r3, r3, #4 @ SET ALE
strb r3, [r1, #24] @ Save to FLASHCTL
mov r2, #0 @ Address 0x00
strb r2, [r1, #20] @ Save to FLASHIO
bic r3, r3, #4 @ CLR ALE
strb r3, [r1, #24] @ Save to FLASHCTL
.fids1:
ldrb r3, [r1, #24] @ Load FLASHCTL
tst r3, #32 @ Is chip ready?
beq .fids1
ldrb r2, [r1, #20] @ NAND Manufacturer ID
ldrb r3, [r1, #20] @ NAND Chip ID
mov pc, lr
.SHARPEND:
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.13-rc2
# Fri Jul 8 04:49:34 2005
# Linux kernel version: 2.6.13
# Mon Sep 5 18:07:12 2005
#
CONFIG_ARM=y
CONFIG_MMU=y
......@@ -102,9 +102,11 @@ CONFIG_OMAP_MUX_WARNINGS=y
# CONFIG_OMAP_MPU_TIMER is not set
CONFIG_OMAP_32K_TIMER=y
CONFIG_OMAP_32K_TIMER_HZ=128
# CONFIG_OMAP_DM_TIMER is not set
CONFIG_OMAP_LL_DEBUG_UART1=y
# CONFIG_OMAP_LL_DEBUG_UART2 is not set
# CONFIG_OMAP_LL_DEBUG_UART3 is not set
CONFIG_OMAP_SERIAL_WAKE=y
#
# OMAP Core Type
......@@ -166,7 +168,6 @@ CONFIG_ISA_DMA_API=y
#
# Kernel Features
#
# CONFIG_SMP is not set
CONFIG_PREEMPT=y
CONFIG_NO_IDLE_HZ=y
# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
......@@ -230,91 +231,82 @@ CONFIG_PM=y
# CONFIG_APM is not set
#
# Device Drivers
#
#
# Generic Driver Options
#
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
#
# Memory Technology Devices (MTD)
# Networking
#
CONFIG_MTD=y
CONFIG_MTD_DEBUG=y
CONFIG_MTD_DEBUG_VERBOSE=3
# CONFIG_MTD_CONCAT is not set
CONFIG_MTD_PARTITIONS=y
# CONFIG_MTD_REDBOOT_PARTS is not set
CONFIG_MTD_CMDLINE_PARTS=y
# CONFIG_MTD_AFS_PARTS is not set
CONFIG_NET=y
#
# User Modules And Translation Layers
# Networking options
#
CONFIG_MTD_CHAR=y
CONFIG_MTD_BLOCK=y
# CONFIG_FTL is not set
# CONFIG_NFTL is not set
# CONFIG_INFTL is not set
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
# CONFIG_NET_KEY is not set
CONFIG_INET=y
# CONFIG_IP_MULTICAST is not set
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_FIB_HASH=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
CONFIG_IP_PNP_BOOTP=y
# CONFIG_IP_PNP_RARP is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_ARPD is not set
# CONFIG_SYN_COOKIES is not set
# CONFIG_INET_AH is not set
# CONFIG_INET_ESP is not set
# CONFIG_INET_IPCOMP is not set
# CONFIG_INET_TUNNEL is not set
CONFIG_IP_TCPDIAG=y
# CONFIG_IP_TCPDIAG_IPV6 is not set
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_BIC=y
# CONFIG_IPV6 is not set
# CONFIG_NETFILTER is not set
#
# RAM/ROM/Flash chip drivers
# SCTP Configuration (EXPERIMENTAL)
#
CONFIG_MTD_CFI=y
# CONFIG_MTD_JEDECPROBE is not set
CONFIG_MTD_GEN_PROBE=y
# CONFIG_MTD_CFI_ADV_OPTIONS is not set
CONFIG_MTD_MAP_BANK_WIDTH_1=y
CONFIG_MTD_MAP_BANK_WIDTH_2=y
CONFIG_MTD_MAP_BANK_WIDTH_4=y
# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
CONFIG_MTD_CFI_I1=y
CONFIG_MTD_CFI_I2=y
# CONFIG_MTD_CFI_I4 is not set
# CONFIG_MTD_CFI_I8 is not set
CONFIG_MTD_CFI_INTELEXT=y
# CONFIG_MTD_CFI_AMDSTD is not set
# CONFIG_MTD_CFI_STAA is not set
CONFIG_MTD_CFI_UTIL=y
# CONFIG_MTD_RAM is not set
# CONFIG_MTD_ROM is not set
# CONFIG_MTD_ABSENT is not set
# CONFIG_MTD_XIP is not set
# CONFIG_IP_SCTP is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_NET_SCHED is not set
# CONFIG_NET_CLS_ROUTE is not set
#
# Mapping drivers for chip access
# Network testing
#
# CONFIG_MTD_COMPLEX_MAPPINGS is not set
# CONFIG_MTD_PHYSMAP is not set
# CONFIG_MTD_ARM_INTEGRATOR is not set
# CONFIG_MTD_EDB7312 is not set
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
#
# Self-contained MTD device drivers
# Device Drivers
#
# CONFIG_MTD_SLRAM is not set
# CONFIG_MTD_PHRAM is not set
# CONFIG_MTD_MTDRAM is not set
# CONFIG_MTD_BLKMTD is not set
# CONFIG_MTD_BLOCK2MTD is not set
#
# Disk-On-Chip Device Drivers
# Generic Driver Options
#
# CONFIG_MTD_DOC2000 is not set
# CONFIG_MTD_DOC2001 is not set
# CONFIG_MTD_DOC2001PLUS is not set
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
# CONFIG_FW_LOADER is not set
#
# NAND Flash Device Drivers
# Memory Technology Devices (MTD)
#
# CONFIG_MTD_NAND is not set
# CONFIG_MTD is not set
#
# Parallel port support
......@@ -403,72 +395,8 @@ CONFIG_SCSI_PROC_FS=y
#
#
# Networking support
#
CONFIG_NET=y
#
# Networking options
#
CONFIG_PACKET=y
# CONFIG_PACKET_MMAP is not set
CONFIG_UNIX=y
# CONFIG_NET_KEY is not set
CONFIG_INET=y
# CONFIG_IP_MULTICAST is not set
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_FIB_HASH=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
CONFIG_IP_PNP_BOOTP=y
# CONFIG_IP_PNP_RARP is not set
# CONFIG_NET_IPIP is not set
# CONFIG_NET_IPGRE is not set
# CONFIG_ARPD is not set
# CONFIG_SYN_COOKIES is not set
# CONFIG_INET_AH is not set
# CONFIG_INET_ESP is not set
# CONFIG_INET_IPCOMP is not set
# CONFIG_INET_TUNNEL is not set
CONFIG_IP_TCPDIAG=y
# CONFIG_IP_TCPDIAG_IPV6 is not set
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_BIC=y
# CONFIG_IPV6 is not set
# CONFIG_NETFILTER is not set
#
# SCTP Configuration (EXPERIMENTAL)
# Network device support
#
# CONFIG_IP_SCTP is not set
# CONFIG_ATM is not set
# CONFIG_BRIDGE is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_DECNET is not set
# CONFIG_LLC2 is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
# CONFIG_NET_CLS_ROUTE is not set
#
# Network testing
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
# CONFIG_HAMRADIO is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
CONFIG_NETDEVICES=y
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
......@@ -518,6 +446,8 @@ CONFIG_SLIP_COMPRESSED=y
# CONFIG_SLIP_MODE_SLIP6 is not set
# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
#
# ISDN subsystem
......@@ -615,77 +545,15 @@ CONFIG_WATCHDOG_NOWAYOUT=y
#
# I2C support
#
CONFIG_I2C=y
CONFIG_I2C_CHARDEV=y
#
# I2C Algorithms
#
# CONFIG_I2C_ALGOBIT is not set
# CONFIG_I2C_ALGOPCF is not set
# CONFIG_I2C_ALGOPCA is not set
#
# I2C Hardware Bus support
#
# CONFIG_I2C_ISA is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_STUB is not set
# CONFIG_I2C_PCA_ISA is not set
# CONFIG_I2C is not set
# CONFIG_I2C_SENSOR is not set
CONFIG_ISP1301_OMAP=y
#
# Hardware Sensors Chip support
# Hardware Monitoring support
#
# CONFIG_I2C_SENSOR is not set
# CONFIG_SENSORS_ADM1021 is not set
# CONFIG_SENSORS_ADM1025 is not set
# CONFIG_SENSORS_ADM1026 is not set
# CONFIG_SENSORS_ADM1031 is not set
# CONFIG_SENSORS_ADM9240 is not set
# CONFIG_SENSORS_ASB100 is not set
# CONFIG_SENSORS_ATXP1 is not set
# CONFIG_SENSORS_DS1621 is not set
# CONFIG_SENSORS_FSCHER is not set
# CONFIG_SENSORS_FSCPOS is not set
# CONFIG_SENSORS_GL518SM is not set
# CONFIG_SENSORS_GL520SM is not set
# CONFIG_SENSORS_IT87 is not set
# CONFIG_SENSORS_LM63 is not set
# CONFIG_SENSORS_LM75 is not set
# CONFIG_SENSORS_LM77 is not set
# CONFIG_SENSORS_LM78 is not set
# CONFIG_SENSORS_LM80 is not set
# CONFIG_SENSORS_LM83 is not set
# CONFIG_SENSORS_LM85 is not set
# CONFIG_SENSORS_LM87 is not set
# CONFIG_SENSORS_LM90 is not set
# CONFIG_SENSORS_LM92 is not set
# CONFIG_SENSORS_MAX1619 is not set
# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SENSORS_SMSC47B397 is not set
# CONFIG_SENSORS_SMSC47M1 is not set
# CONFIG_SENSORS_W83781D is not set
# CONFIG_SENSORS_W83L785TS is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
#
# Other I2C Chip support
#
# CONFIG_SENSORS_DS1337 is not set
# CONFIG_SENSORS_DS1374 is not set
# CONFIG_SENSORS_EEPROM is not set
# CONFIG_SENSORS_PCF8574 is not set
# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_PCF8591 is not set
# CONFIG_SENSORS_RTC8564 is not set
CONFIG_ISP1301_OMAP=y
CONFIG_TPS65010=y
# CONFIG_SENSORS_MAX6875 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
CONFIG_HWMON=y
# CONFIG_HWMON_DEBUG_CHIP is not set
#
# Misc devices
......@@ -756,15 +624,9 @@ CONFIG_SOUND=y
# Open Sound System
#
CONFIG_SOUND_PRIME=y
# CONFIG_SOUND_BT878 is not set
# CONFIG_SOUND_FUSION is not set
# CONFIG_SOUND_CS4281 is not set
# CONFIG_SOUND_SONICVIBES is not set
# CONFIG_SOUND_TRIDENT is not set
# CONFIG_SOUND_MSNDCLAS is not set
# CONFIG_SOUND_MSNDPIN is not set
# CONFIG_SOUND_OSS is not set
# CONFIG_SOUND_TVMIXER is not set
# CONFIG_SOUND_AD1980 is not set
#
......@@ -810,6 +672,7 @@ CONFIG_EXT2_FS=y
# CONFIG_JBD is not set
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
#
# XFS support
......@@ -817,6 +680,7 @@ CONFIG_EXT2_FS=y
# CONFIG_XFS_FS is not set
# CONFIG_MINIX_FS is not set
CONFIG_ROMFS_FS=y
CONFIG_INOTIFY=y
# CONFIG_QUOTA is not set
CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
......@@ -857,15 +721,6 @@ CONFIG_RAMFS=y
# CONFIG_BEFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_EFS_FS is not set
# CONFIG_JFFS_FS is not set
CONFIG_JFFS2_FS=y
CONFIG_JFFS2_FS_DEBUG=2
# CONFIG_JFFS2_FS_NAND is not set
# CONFIG_JFFS2_FS_NOR_ECC is not set
# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
CONFIG_JFFS2_ZLIB=y
CONFIG_JFFS2_RTIME=y
# CONFIG_JFFS2_RUBIN is not set
CONFIG_CRAMFS=y
# CONFIG_VXFS_FS is not set
# CONFIG_HPFS_FS is not set
......@@ -1007,4 +862,3 @@ CONFIG_CRYPTO_DES=y
CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
......@@ -60,7 +60,7 @@ static unsigned long iop321_gettimeoffset(void)
/*
* Now convert them to usec.
*/
usec = (unsigned long)(elapsed * (tick_nsec / 1000)) / LATCH;
usec = (unsigned long)(elapsed / (CLOCK_TICK_RATE/1000000));
return usec;
}
......
......@@ -58,7 +58,7 @@ static unsigned long iop331_gettimeoffset(void)
/*
* Now convert them to usec.
*/
usec = (unsigned long)(elapsed * (tick_nsec / 1000)) / LATCH;
usec = (unsigned long)(elapsed / (CLOCK_TICK_RATE/1000000));
return usec;
}
......
......@@ -382,7 +382,7 @@ static void ixp2000_GPIO_irq_unmask(unsigned int irq)
static struct irqchip ixp2000_GPIO_irq_chip = {
.ack = ixp2000_GPIO_irq_mask_ack,
.mask = ixp2000_GPIO_irq_mask,
.unmask = ixp2000_GPIO_irq_unmask
.unmask = ixp2000_GPIO_irq_unmask,
.set_type = ixp2000_GPIO_irq_type,
};
......
......@@ -179,17 +179,17 @@ static void ixp4xx_irq_level_unmask(unsigned int irq)
}
static struct irqchip ixp4xx_irq_level_chip = {
.ack = ixp4xx_irq_mask,
.mask = ixp4xx_irq_mask,
.unmask = ixp4xx_irq_level_unmask,
.type = ixp4xx_set_irq_type
.ack = ixp4xx_irq_mask,
.mask = ixp4xx_irq_mask,
.unmask = ixp4xx_irq_level_unmask,
.set_type = ixp4xx_set_irq_type,
};
static struct irqchip ixp4xx_irq_edge_chip = {
.ack = ixp4xx_irq_ack,
.mask = ixp4xx_irq_mask,
.unmask = ixp4xx_irq_unmask,
.type = ixp4xx_set_irq_type
.ack = ixp4xx_irq_ack,
.mask = ixp4xx_irq_mask,
.unmask = ixp4xx_irq_unmask,
.set_type = ixp4xx_set_irq_type,
};
static void ixp4xx_config_irq(unsigned irq, enum ixp4xx_irq_type type)
......
......@@ -165,10 +165,10 @@ static struct omap_irq_bank omap1610_irq_banks[] = {
#endif
static struct irqchip omap_irq_chip = {
.ack = omap_mask_ack_irq,
.mask = omap_mask_irq,
.unmask = omap_unmask_irq,
.wake = omap_wake_irq,
.ack = omap_mask_ack_irq,
.mask = omap_mask_irq,
.unmask = omap_unmask_irq,
.set_wake = omap_wake_irq,
};
void __init omap_init_irq(void)
......
......@@ -2,6 +2,13 @@ if ARCH_S3C2410
menu "S3C24XX Implementations"
config MACH_ANUBIS
bool "Simtec Electronics ANUBIS"
select CPU_S3C2440
help
Say Y gere if you are using the Simtec Electronics ANUBIS
development system
config ARCH_BAST
bool "Simtec Electronics BAST (EB2410ITX)"
select CPU_S3C2410
......@@ -11,6 +18,14 @@ config ARCH_BAST
Product page: <http://www.simtec.co.uk/products/EB2410ITX/>.
config BAST_PC104_IRQ
bool "BAST PC104 IRQ support"
depends on ARCH_BAST
default y
help
Say Y here to enable the PC104 IRQ routing on the
Simtec BAST (EB2410ITX)
config ARCH_H1940
bool "IPAQ H1940"
select CPU_S3C2410
......
......@@ -26,8 +26,13 @@ obj-$(CONFIG_CPU_S3C2440) += s3c2440.o s3c2440-dsc.o
obj-$(CONFIG_CPU_S3C2440) += s3c2440-irq.o
obj-$(CONFIG_CPU_S3C2440) += s3c2440-clock.o
# bast extras
obj-$(CONFIG_BAST_PC104_IRQ) += bast-irq.o
# machine specific support
obj-$(CONFIG_MACH_ANUBIS) += mach-anubis.o
obj-$(CONFIG_ARCH_BAST) += mach-bast.o usb-simtec.o
obj-$(CONFIG_ARCH_H1940) += mach-h1940.o
obj-$(CONFIG_MACH_N30) += mach-n30.o
......
/* linux/arch/arm/mach-s3c2410/bast-irq.c
*
* Copyright (c) 2004 Simtec Electronics
* Copyright (c) 2003,2005 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
*
* http://www.simtec.co.uk/products/EB2410ITX/
......@@ -21,7 +21,8 @@
*
* Modifications:
* 08-Jan-2003 BJD Moved from central IRQ code
*/
* 21-Aug-2005 BJD Fixed missing code and compile errors
*/
#include <linux/init.h>
......@@ -30,12 +31,19 @@
#include <linux/ptrace.h>
#include <linux/sysdev.h>
#include <asm/mach-types.h>
#include <asm/hardware.h>
#include <asm/irq.h>
#include <asm/io.h>
#include <asm/mach/irq.h>
#include <asm/hardware/s3c2410/irq.h>
#include <asm/arch/regs-irq.h>
#include <asm/arch/bast-map.h>
#include <asm/arch/bast-irq.h>
#include "irq.h"
#if 0
#include <asm/debug-ll.h>
......@@ -79,15 +87,15 @@ bast_pc104_mask(unsigned int irqno)
temp = __raw_readb(BAST_VA_PC104_IRQMASK);
temp &= ~bast_pc104_irqmasks[irqno];
__raw_writeb(temp, BAST_VA_PC104_IRQMASK);
if (temp == 0)
bast_extint_mask(IRQ_ISA);
}
static void
bast_pc104_ack(unsigned int irqno)
bast_pc104_maskack(unsigned int irqno)
{
bast_extint_ack(IRQ_ISA);
struct irqdesc *desc = irq_desc + IRQ_ISA;
bast_pc104_mask(irqno);
desc->chip->ack(IRQ_ISA);
}
static void
......@@ -98,14 +106,12 @@ bast_pc104_unmask(unsigned int irqno)
temp = __raw_readb(BAST_VA_PC104_IRQMASK);
temp |= bast_pc104_irqmasks[irqno];
__raw_writeb(temp, BAST_VA_PC104_IRQMASK);
bast_extint_unmask(IRQ_ISA);
}
static struct bast_pc104_chip = {
static struct irqchip bast_pc104_chip = {
.mask = bast_pc104_mask,
.unmask = bast_pc104_unmask,
.ack = bast_pc104_ack
.ack = bast_pc104_maskack
};
static void
......@@ -119,14 +125,49 @@ bast_irq_pc104_demux(unsigned int irq,
stat = __raw_readb(BAST_VA_PC104_IRQREQ) & 0xf;
for (i = 0; i < 4 && stat != 0; i++) {
if (stat & 1) {
irqno = bast_pc104_irqs[i];
desc = irq_desc + irqno;
if (unlikely(stat == 0)) {
/* ack if we get an irq with nothing (ie, startup) */
desc = irq_desc + IRQ_ISA;
desc->chip->ack(IRQ_ISA);
} else {
/* handle the IRQ */
for (i = 0; stat != 0; i++, stat >>= 1) {
if (stat & 1) {
irqno = bast_pc104_irqs[i];
desc_handle_irq(irqno, desc, regs);
desc_handle_irq(irqno, irq_desc + irqno, regs);
}
}
}
}
stat >>= 1;
static __init int bast_irq_init(void)
{
unsigned int i;
if (machine_is_bast()) {
printk(KERN_INFO "BAST PC104 IRQ routing, (c) 2005 Simtec Electronics\n");
/* zap all the IRQs */
__raw_writeb(0x0, BAST_VA_PC104_IRQMASK);
set_irq_chained_handler(IRQ_ISA, bast_irq_pc104_demux);
/* reigster our IRQs */
for (i = 0; i < 4; i++) {
unsigned int irqno = bast_pc104_irqs[i];
set_irq_chip(irqno, &bast_pc104_chip);
set_irq_handler(irqno, do_level_IRQ);
set_irq_flags(irqno, IRQF_VALID);
}
}
return 0;
}
arch_initcall(bast_irq_init);
/* linux/arch/arm/mach-s3c2410/mach-anubis.c
*
* Copyright (c) 2003-2005 Simtec Electronics
* http://armlinux.simtec.co.uk/
* Ben Dooks <ben@simtec.co.uk>
*
*
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* Modifications:
* 02-May-2005 BJD Copied from mach-bast.c
*/
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/interrupt.h>
#include <linux/list.h>
#include <linux/timer.h>
#include <linux/init.h>
#include <linux/device.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
#include <asm/arch/anubis-map.h>
#include <asm/arch/anubis-irq.h>
#include <asm/arch/anubis-cpld.h>
#include <asm/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <asm/arch/regs-serial.h>
#include <asm/arch/regs-gpio.h>
#include <asm/arch/regs-mem.h>
#include <asm/arch/regs-lcd.h>
#include <asm/arch/nand.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/nand_ecc.h>
#include <linux/mtd/partitions.h>
#include "clock.h"
#include "devs.h"
#include "cpu.h"
#define COPYRIGHT ", (c) 2005 Simtec Electronics"
static struct map_desc anubis_iodesc[] __initdata = {
/* ISA IO areas */
{ (u32)S3C24XX_VA_ISA_BYTE, 0x0, SZ_16M, MT_DEVICE },
{ (u32)S3C24XX_VA_ISA_WORD, 0x0, SZ_16M, MT_DEVICE },
/* we could possibly compress the next set down into a set of smaller tables
* pagetables, but that would mean using an L2 section, and it still means
* we cannot actually feed the same register to an LDR due to 16K spacing
*/
/* CPLD control registers */
{ (u32)ANUBIS_VA_CTRL1, ANUBIS_PA_CTRL1, SZ_4K, MT_DEVICE },
{ (u32)ANUBIS_VA_CTRL2, ANUBIS_PA_CTRL2, SZ_4K, MT_DEVICE },
/* IDE drives */
{ (u32)ANUBIS_IDEPRI, S3C2410_CS3, SZ_1M, MT_DEVICE },
{ (u32)ANUBIS_IDEPRIAUX, S3C2410_CS3+(1<<26), SZ_1M, MT_DEVICE },
{ (u32)ANUBIS_IDESEC, S3C2410_CS4, SZ_1M, MT_DEVICE },
{ (u32)ANUBIS_IDESECAUX, S3C2410_CS4+(1<<26), SZ_1M, MT_DEVICE },
};
#define UCON S3C2410_UCON_DEFAULT | S3C2410_UCON_UCLK
#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB
#define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE
static struct s3c24xx_uart_clksrc anubis_serial_clocks[] = {
[0] = {
.name = "uclk",
.divisor = 1,
.min_baud = 0,
.max_baud = 0,
},
[1] = {
.name = "pclk",
.divisor = 1,
.min_baud = 0,
.max_baud = 0.
}
};
static struct s3c2410_uartcfg anubis_uartcfgs[] = {
[0] = {
.hwport = 0,
.flags = 0,
.ucon = UCON,
.ulcon = ULCON,
.ufcon = UFCON,
.clocks = anubis_serial_clocks,
.clocks_size = ARRAY_SIZE(anubis_serial_clocks)
},
[1] = {
.hwport = 2,
.flags = 0,
.ucon = UCON,
.ulcon = ULCON,
.ufcon = UFCON,
.clocks = anubis_serial_clocks,
.clocks_size = ARRAY_SIZE(anubis_serial_clocks)
},
};
/* NAND Flash on Anubis board */
static int external_map[] = { 2 };
static int chip0_map[] = { 0 };
static int chip1_map[] = { 1 };
struct mtd_partition anubis_default_nand_part[] = {
[0] = {
.name = "Boot Agent",
.size = SZ_16K,
.offset = 0
},
[1] = {
.name = "/boot",
.size = SZ_4M - SZ_16K,
.offset = SZ_16K,
},
[2] = {
.name = "user1",
.offset = SZ_4M,
.size = SZ_32M - SZ_4M,
},
[3] = {
.name = "user2",
.offset = SZ_32M,
.size = MTDPART_SIZ_FULL,
}
};
/* the Anubis has 3 selectable slots for nand-flash, the two
* on-board chip areas, as well as the external slot.
*
* Note, there is no current hot-plug support for the External
* socket.
*/
static struct s3c2410_nand_set anubis_nand_sets[] = {
[1] = {
.name = "External",
.nr_chips = 1,
.nr_map = external_map,
.nr_partitions = ARRAY_SIZE(anubis_default_nand_part),
.partitions = anubis_default_nand_part
},
[0] = {
.name = "chip0",
.nr_chips = 1,
.nr_map = chip0_map,
.nr_partitions = ARRAY_SIZE(anubis_default_nand_part),
.partitions = anubis_default_nand_part
},
[2] = {
.name = "chip1",
.nr_chips = 1,
.nr_map = chip1_map,
.nr_partitions = ARRAY_SIZE(anubis_default_nand_part),
.partitions = anubis_default_nand_part
},
};
static void anubis_nand_select(struct s3c2410_nand_set *set, int slot)
{
unsigned int tmp;
slot = set->nr_map[slot] & 3;
pr_debug("anubis_nand: selecting slot %d (set %p,%p)\n",
slot, set, set->nr_map);
tmp = __raw_readb(ANUBIS_VA_CTRL1);
tmp &= ~ANUBIS_CTRL1_NANDSEL;
tmp |= slot;
pr_debug("anubis_nand: ctrl1 now %02x\n", tmp);
__raw_writeb(tmp, ANUBIS_VA_CTRL1);
}
static struct s3c2410_platform_nand anubis_nand_info = {
.tacls = 25,
.twrph0 = 80,
.twrph1 = 80,
.nr_sets = ARRAY_SIZE(anubis_nand_sets),
.sets = anubis_nand_sets,
.select_chip = anubis_nand_select,
};
/* Standard Anubis devices */
static struct platform_device *anubis_devices[] __initdata = {
&s3c_device_usb,
&s3c_device_wdt,
&s3c_device_adc,
&s3c_device_i2c,
&s3c_device_rtc,
&s3c_device_nand,
};
static struct clk *anubis_clocks[] = {
&s3c24xx_dclk0,
&s3c24xx_dclk1,
&s3c24xx_clkout0,
&s3c24xx_clkout1,
&s3c24xx_uclk,
};
static struct s3c24xx_board anubis_board __initdata = {
.devices = anubis_devices,
.devices_count = ARRAY_SIZE(anubis_devices),
.clocks = anubis_clocks,
.clocks_count = ARRAY_SIZE(anubis_clocks)
};
void __init anubis_map_io(void)
{
/* initialise the clocks */
s3c24xx_dclk0.parent = NULL;
s3c24xx_dclk0.rate = 12*1000*1000;
s3c24xx_dclk1.parent = NULL;
s3c24xx_dclk1.rate = 24*1000*1000;
s3c24xx_clkout0.parent = &s3c24xx_dclk0;
s3c24xx_clkout1.parent = &s3c24xx_dclk1;
s3c24xx_uclk.parent = &s3c24xx_clkout1;
s3c_device_nand.dev.platform_data = &anubis_nand_info;
s3c24xx_init_io(anubis_iodesc, ARRAY_SIZE(anubis_iodesc));
s3c24xx_init_clocks(0);
s3c24xx_init_uarts(anubis_uartcfgs, ARRAY_SIZE(anubis_uartcfgs));
s3c24xx_set_board(&anubis_board);
/* ensure that the GPIO is setup */
s3c2410_gpio_setpin(S3C2410_GPA0, 1);
}
MACHINE_START(ANUBIS, "Simtec-Anubis")
/* Maintainer: Ben Dooks <ben@simtec.co.uk> */
.phys_ram = S3C2410_SDRAM_PA,
.phys_io = S3C2410_PA_UART,
.io_pg_offst = (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc,
.boot_params = S3C2410_SDRAM_PA + 0x100,
.map_io = anubis_map_io,
.init_irq = s3c24xx_init_irq,
.timer = &s3c24xx_timer,
MACHINE_END
......@@ -48,7 +48,7 @@ static __init int pm_simtec_init(void)
/* check which machine we are running on */
if (!machine_is_bast() && !machine_is_vr1000())
if (!machine_is_bast() && !machine_is_vr1000() && !machine_is_anubis())
return 0;
printk(KERN_INFO "Simtec Board Power Manangement" COPYRIGHT "\n");
......
......@@ -164,7 +164,7 @@ static void s3c2410_timer_setup (void)
/* configure the system for whichever machine is in use */
if (machine_is_bast() || machine_is_vr1000()) {
if (machine_is_bast() || machine_is_vr1000() || machine_is_anubis()) {
/* timer is at 12MHz, scaler is 1 */
timer_usec_ticks = timer_mask_usec_ticks(1, 12000000);
tcnt = 12000000 / HZ;
......
......@@ -91,6 +91,13 @@ config OMAP_32K_TIMER_HZ
Kernel internal timer frequency should be a divisor of 32768,
such as 64 or 128.
config OMAP_DM_TIMER
bool "Use dual-mode timer"
default n
depends on ARCH_OMAP16XX
help
Select this option if you want to use OMAP Dual-Mode timers.
choice
prompt "Low-level debug console UART"
depends on ARCH_OMAP
......@@ -107,6 +114,15 @@ config OMAP_LL_DEBUG_UART3
endchoice
config OMAP_SERIAL_WAKE
bool "Enable wake-up events for serial ports"
depends OMAP_MUX
default y
help
Select this option if you want to have your system wake up
to data on the serial RX line. This allows you to wake the
system from serial console.
endmenu
endif
......@@ -3,7 +3,7 @@
#
# Common support
obj-y := common.o dma.o clock.o mux.o gpio.o mcbsp.o usb.o
obj-y := common.o sram.o sram-fn.o clock.o dma.o mux.o gpio.o mcbsp.o usb.o
obj-m :=
obj-n :=
obj- :=
......@@ -15,3 +15,5 @@ obj-$(CONFIG_ARCH_OMAP16XX) += ocpi.o
obj-$(CONFIG_PM) += pm.o sleep.o
obj-$(CONFIG_CPU_FREQ) += cpu-omap.o
obj-$(CONFIG_OMAP_DM_TIMER) += dmtimer.o
......@@ -21,6 +21,7 @@
#include <asm/arch/usb.h>
#include "clock.h"
#include "sram.h"
static LIST_HEAD(clocks);
static DECLARE_MUTEX(clocks_sem);
......@@ -141,7 +142,7 @@ static struct clk arm_ck = {
static struct clk armper_ck = {
.name = "armper_ck",
.parent = &ck_dpll1,
.flags = CLOCK_IN_OMAP730 | CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX |
.flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX |
RATE_CKCTL,
.enable_reg = ARM_IDLECT2,
.enable_bit = EN_PERCK,
......@@ -385,7 +386,8 @@ static struct clk uart2_ck = {
.name = "uart2_ck",
/* Direct from ULPD, no parent */
.rate = 12000000,
.flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX | ENABLE_REG_32BIT,
.flags = CLOCK_IN_OMAP1510 | CLOCK_IN_OMAP16XX | ENABLE_REG_32BIT |
ALWAYS_ENABLED,
.enable_reg = MOD_CONF_CTRL_0,
.enable_bit = 30, /* Chooses between 12MHz and 48MHz */
.set_rate = &set_uart_rate,
......@@ -443,6 +445,15 @@ static struct clk usb_hhc_ck16xx = {
.enable_bit = 8 /* UHOST_EN */,
};
static struct clk usb_dc_ck = {
.name = "usb_dc_ck",
/* Direct from ULPD, no parent */
.rate = 48000000,
.flags = CLOCK_IN_OMAP16XX | RATE_FIXED,
.enable_reg = SOFT_REQ_REG,
.enable_bit = 4,
};
static struct clk mclk_1510 = {
.name = "mclk",
/* Direct from ULPD, no parent. May be enabled by ext hardware. */
......@@ -552,6 +563,7 @@ static struct clk * onchip_clks[] = {
&uart3_16xx,
&usb_clko,
&usb_hhc_ck1510, &usb_hhc_ck16xx,
&usb_dc_ck,
&mclk_1510, &mclk_16xx,
&bclk_1510, &bclk_16xx,
&mmc1_ck,
......@@ -946,14 +958,13 @@ static int select_table_rate(struct clk * clk, unsigned long rate)
if (!ptr->rate)
return -EINVAL;
if (!ptr->rate)
return -EINVAL;
/*
* In most cases we should not need to reprogram DPLL.
* Reprogramming the DPLL is tricky, it must be done from SRAM.
*/
omap_sram_reprogram_clock(ptr->dpllctl_val, ptr->ckctl_val);
if (unlikely(ck_dpll1.rate == 0)) {
omap_writew(ptr->dpllctl_val, DPLL_CTL);
ck_dpll1.rate = ptr->pll_rate;
}
omap_writew(ptr->ckctl_val, ARM_CKCTL);
ck_dpll1.rate = ptr->pll_rate;
propagate_rate(&ck_dpll1);
return 0;
}
......@@ -1224,9 +1235,11 @@ int __init clk_init(void)
#endif
/* Cache rates for clocks connected to ck_ref (not dpll1) */
propagate_rate(&ck_ref);
printk(KERN_INFO "Clocking rate (xtal/DPLL1/MPU): %ld.%01ld/%ld/%ld MHz\n",
printk(KERN_INFO "Clocking rate (xtal/DPLL1/MPU): "
"%ld.%01ld/%ld.%01ld/%ld.%01ld MHz\n",
ck_ref.rate / 1000000, (ck_ref.rate / 100000) % 10,
ck_dpll1.rate, arm_ck.rate);
ck_dpll1.rate / 1000000, (ck_dpll1.rate / 100000) % 10,
arm_ck.rate / 1000000, (arm_ck.rate / 100000) % 10);
#ifdef CONFIG_MACH_OMAP_PERSEUS2
/* Select slicer output as OMAP input clock */
......@@ -1271,7 +1284,9 @@ static int __init omap_late_clk_reset(void)
struct clk *p;
__u32 regval32;
omap_writew(0, SOFT_REQ_REG);
/* USB_REQ_EN will be disabled later if necessary (usb_dc_ck) */
regval32 = omap_readw(SOFT_REQ_REG) & (1 << 4);
omap_writew(regval32, SOFT_REQ_REG);
omap_writew(0, SOFT_REQ_REG2);
list_for_each_entry(p, &clocks, node) {
......
......@@ -26,6 +26,7 @@
#include <asm/hardware/clock.h>
#include <asm/io.h>
#include <asm/mach-types.h>
#include <asm/setup.h>
#include <asm/arch/board.h>
#include <asm/arch/mux.h>
......@@ -35,11 +36,11 @@
#define NO_LENGTH_CHECK 0xffffffff
extern int omap_bootloader_tag_len;
extern u8 omap_bootloader_tag[];
unsigned char omap_bootloader_tag[512];
int omap_bootloader_tag_len;
struct omap_board_config_kernel *omap_board_config;
int omap_board_config_size = 0;
int omap_board_config_size;
static const void *get_config(u16 tag, size_t len, int skip, size_t *len_out)
{
......
......@@ -425,7 +425,7 @@ static int dma_handle_ch(int ch)
dma_chan[ch + 6].saved_csr = csr >> 7;
csr &= 0x7f;
}
if (!csr)
if ((csr & 0x3f) == 0)
return 0;
if (unlikely(dma_chan[ch].dev_id == -1)) {
printk(KERN_WARNING "Spurious interrupt from DMA channel %d (CSR %04x)\n",
......@@ -890,11 +890,11 @@ void omap_enable_lcd_dma(void)
w |= 1 << 8;
omap_writew(w, OMAP1610_DMA_LCD_CTRL);
lcd_dma.active = 1;
w = omap_readw(OMAP1610_DMA_LCD_CCR);
w |= 1 << 7;
omap_writew(w, OMAP1610_DMA_LCD_CCR);
lcd_dma.active = 1;
}
void omap_setup_lcd_dma(void)
......@@ -965,8 +965,8 @@ void omap_clear_dma(int lch)
*/
dma_addr_t omap_get_dma_src_pos(int lch)
{
return (dma_addr_t) (OMAP_DMA_CSSA_L(lch) |
(OMAP_DMA_CSSA_U(lch) << 16));
return (dma_addr_t) (omap_readw(OMAP_DMA_CSSA_L(lch)) |
(omap_readw(OMAP_DMA_CSSA_U(lch)) << 16));
}
/*
......@@ -979,8 +979,18 @@ dma_addr_t omap_get_dma_src_pos(int lch)
*/
dma_addr_t omap_get_dma_dst_pos(int lch)
{
return (dma_addr_t) (OMAP_DMA_CDSA_L(lch) |
(OMAP_DMA_CDSA_U(lch) << 16));
return (dma_addr_t) (omap_readw(OMAP_DMA_CDSA_L(lch)) |
(omap_readw(OMAP_DMA_CDSA_U(lch)) << 16));
}
/*
* Returns current source transfer counting for the given DMA channel.
* Can be used to monitor the progress of a transfer inside a block.
* It must be called with disabled interrupts.
*/
int omap_get_dma_src_addr_counter(int lch)
{
return (dma_addr_t) omap_readw(OMAP_DMA_CSAC(lch));
}
int omap_dma_running(void)
......@@ -1076,6 +1086,7 @@ arch_initcall(omap_init_dma);
EXPORT_SYMBOL(omap_get_dma_src_pos);
EXPORT_SYMBOL(omap_get_dma_dst_pos);
EXPORT_SYMBOL(omap_get_dma_src_addr_counter);
EXPORT_SYMBOL(omap_clear_dma);
EXPORT_SYMBOL(omap_set_dma_priority);
EXPORT_SYMBOL(omap_request_dma);
......
/*
* linux/arch/arm/plat-omap/dmtimer.c
*
* OMAP Dual-Mode Timers
*
* Copyright (C) 2005 Nokia Corporation
* Author: Lauri Leukkunen <lauri.leukkunen@nokia.com>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*
* THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
* NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#include <linux/init.h>
#include <asm/arch/hardware.h>
#include <asm/arch/dmtimer.h>
#include <asm/io.h>
#include <asm/arch/irqs.h>
#include <linux/spinlock.h>
#include <linux/list.h>
#define OMAP_TIMER_COUNT 8
#define OMAP_TIMER_ID_REG 0x00
#define OMAP_TIMER_OCP_CFG_REG 0x10
#define OMAP_TIMER_SYS_STAT_REG 0x14
#define OMAP_TIMER_STAT_REG 0x18
#define OMAP_TIMER_INT_EN_REG 0x1c
#define OMAP_TIMER_WAKEUP_EN_REG 0x20
#define OMAP_TIMER_CTRL_REG 0x24
#define OMAP_TIMER_COUNTER_REG 0x28
#define OMAP_TIMER_LOAD_REG 0x2c
#define OMAP_TIMER_TRIGGER_REG 0x30
#define OMAP_TIMER_WRITE_PEND_REG 0x34
#define OMAP_TIMER_MATCH_REG 0x38
#define OMAP_TIMER_CAPTURE_REG 0x3c
#define OMAP_TIMER_IF_CTRL_REG 0x40
static struct dmtimer_info_struct {
struct list_head unused_timers;
struct list_head reserved_timers;
} dm_timer_info;
static struct omap_dm_timer dm_timers[] = {
{ .base=0xfffb1400, .irq=INT_1610_GPTIMER1 },
{ .base=0xfffb1c00, .irq=INT_1610_GPTIMER2 },
{ .base=0xfffb2400, .irq=INT_1610_GPTIMER3 },
{ .base=0xfffb2c00, .irq=INT_1610_GPTIMER4 },
{ .base=0xfffb3400, .irq=INT_1610_GPTIMER5 },
{ .base=0xfffb3c00, .irq=INT_1610_GPTIMER6 },
{ .base=0xfffb4400, .irq=INT_1610_GPTIMER7 },
{ .base=0xfffb4c00, .irq=INT_1610_GPTIMER8 },
{ .base=0x0 },
};
static spinlock_t dm_timer_lock;
inline void omap_dm_timer_write_reg(struct omap_dm_timer *timer, int reg, u32 value)
{
omap_writel(value, timer->base + reg);
while (omap_dm_timer_read_reg(timer, OMAP_TIMER_WRITE_PEND_REG))
;
}
u32 omap_dm_timer_read_reg(struct omap_dm_timer *timer, int reg)
{
return omap_readl(timer->base + reg);
}
int omap_dm_timers_active(void)
{
struct omap_dm_timer *timer;
for (timer = &dm_timers[0]; timer->base; ++timer)
if (omap_dm_timer_read_reg(timer, OMAP_TIMER_CTRL_REG) &
OMAP_TIMER_CTRL_ST)
return 1;
return 0;
}
void omap_dm_timer_set_source(struct omap_dm_timer *timer, int source)
{
int n = (timer - dm_timers) << 1;
u32 l;
l = omap_readl(MOD_CONF_CTRL_1) & ~(0x03 << n);
l |= source << n;
omap_writel(l, MOD_CONF_CTRL_1);
}
static void omap_dm_timer_reset(struct omap_dm_timer *timer)
{
/* Reset and set posted mode */
omap_dm_timer_write_reg(timer, OMAP_TIMER_IF_CTRL_REG, 0x06);
omap_dm_timer_write_reg(timer, OMAP_TIMER_OCP_CFG_REG, 0x02);
omap_dm_timer_set_source(timer, OMAP_TIMER_SRC_ARMXOR);
}
struct omap_dm_timer * omap_dm_timer_request(void)
{
struct omap_dm_timer *timer = NULL;
unsigned long flags;
spin_lock_irqsave(&dm_timer_lock, flags);
if (!list_empty(&dm_timer_info.unused_timers)) {
timer = (struct omap_dm_timer *)
dm_timer_info.unused_timers.next;
list_move_tail((struct list_head *)timer,
&dm_timer_info.reserved_timers);
}
spin_unlock_irqrestore(&dm_timer_lock, flags);
return timer;
}
void omap_dm_timer_free(struct omap_dm_timer *timer)
{
unsigned long flags;
omap_dm_timer_reset(timer);
spin_lock_irqsave(&dm_timer_lock, flags);
list_move_tail((struct list_head *)timer, &dm_timer_info.unused_timers);
spin_unlock_irqrestore(&dm_timer_lock, flags);
}
void omap_dm_timer_set_int_enable(struct omap_dm_timer *timer,
unsigned int value)
{
omap_dm_timer_write_reg(timer, OMAP_TIMER_INT_EN_REG, value);
}
unsigned int omap_dm_timer_read_status(struct omap_dm_timer *timer)
{
return omap_dm_timer_read_reg(timer, OMAP_TIMER_STAT_REG);
}
void omap_dm_timer_write_status(struct omap_dm_timer *timer, unsigned int value)
{
omap_dm_timer_write_reg(timer, OMAP_TIMER_STAT_REG, value);
}
void omap_dm_timer_enable_autoreload(struct omap_dm_timer *timer)
{
u32 l;
l = omap_dm_timer_read_reg(timer, OMAP_TIMER_CTRL_REG);
l |= OMAP_TIMER_CTRL_AR;
omap_dm_timer_write_reg(timer, OMAP_TIMER_CTRL_REG, l);
}
void omap_dm_timer_trigger(struct omap_dm_timer *timer)
{
omap_dm_timer_write_reg(timer, OMAP_TIMER_TRIGGER_REG, 1);
}
void omap_dm_timer_set_trigger(struct omap_dm_timer *timer, unsigned int value)
{
u32 l;
l = omap_dm_timer_read_reg(timer, OMAP_TIMER_CTRL_REG);
l |= value & 0x3;
omap_dm_timer_write_reg(timer, OMAP_TIMER_CTRL_REG, l);
}
void omap_dm_timer_start(struct omap_dm_timer *timer)
{
u32 l;
l = omap_dm_timer_read_reg(timer, OMAP_TIMER_CTRL_REG);
l |= OMAP_TIMER_CTRL_ST;
omap_dm_timer_write_reg(timer, OMAP_TIMER_CTRL_REG, l);
}
void omap_dm_timer_stop(struct omap_dm_timer *timer)
{
u32 l;
l = omap_dm_timer_read_reg(timer, OMAP_TIMER_CTRL_REG);
l &= ~0x1;
omap_dm_timer_write_reg(timer, OMAP_TIMER_CTRL_REG, l);
}
unsigned int omap_dm_timer_read_counter(struct omap_dm_timer *timer)
{
return omap_dm_timer_read_reg(timer, OMAP_TIMER_COUNTER_REG);
}
void omap_dm_timer_reset_counter(struct omap_dm_timer *timer)
{
omap_dm_timer_write_reg(timer, OMAP_TIMER_COUNTER_REG, 0);
}
void omap_dm_timer_set_load(struct omap_dm_timer *timer, unsigned int load)
{
omap_dm_timer_write_reg(timer, OMAP_TIMER_LOAD_REG, load);
}
void omap_dm_timer_set_match(struct omap_dm_timer *timer, unsigned int match)
{
omap_dm_timer_write_reg(timer, OMAP_TIMER_MATCH_REG, match);
}
void omap_dm_timer_enable_compare(struct omap_dm_timer *timer)
{
u32 l;
l = omap_dm_timer_read_reg(timer, OMAP_TIMER_CTRL_REG);
l |= OMAP_TIMER_CTRL_CE;
omap_dm_timer_write_reg(timer, OMAP_TIMER_CTRL_REG, l);
}
static inline void __dm_timer_init(void)
{
struct omap_dm_timer *timer;
spin_lock_init(&dm_timer_lock);
INIT_LIST_HEAD(&dm_timer_info.unused_timers);
INIT_LIST_HEAD(&dm_timer_info.reserved_timers);
timer = &dm_timers[0];
while (timer->base) {
list_add_tail((struct list_head *)timer, &dm_timer_info.unused_timers);
omap_dm_timer_reset(timer);
timer++;
}
}
static int __init omap_dm_timer_init(void)
{
if (cpu_is_omap16xx())
__dm_timer_init();
return 0;
}
arch_initcall(omap_dm_timer_init);
This diff is collapsed.
......@@ -27,6 +27,7 @@
#include <asm/arch/dma.h>
#include <asm/arch/mux.h>
#include <asm/arch/irqs.h>
#include <asm/arch/dsp_common.h>
#include <asm/arch/mcbsp.h>
#include <asm/hardware/clock.h>
......@@ -187,9 +188,6 @@ static int omap_mcbsp_check(unsigned int id)
return -1;
}
#define EN_XORPCK 1
#define DSP_RSTCT2 0xe1008014
static void omap_mcbsp_dsp_request(void)
{
if (cpu_is_omap1510() || cpu_is_omap16xx()) {
......@@ -198,6 +196,11 @@ static void omap_mcbsp_dsp_request(void)
/* enable 12MHz clock to mcbsp 1 & 3 */
clk_use(mcbsp_dspxor_ck);
/*
* DSP external peripheral reset
* FIXME: This should be moved to dsp code
*/
__raw_writew(__raw_readw(DSP_RSTCT2) | 1 | 1 << 1,
DSP_RSTCT2);
}
......
......@@ -48,6 +48,9 @@ omap_cfg_reg(const reg_cfg_t reg_cfg)
pull_orig = 0, pull = 0;
unsigned int mask, warn = 0;
if (cpu_is_omap7xx())
return 0;
if (reg_cfg > ARRAY_SIZE(reg_cfg_table)) {
printk(KERN_ERR "MUX: reg_cfg %d\n", reg_cfg);
return -EINVAL;
......
......@@ -25,6 +25,7 @@
#include <linux/config.h>
#include <linux/module.h>
#include <linux/version.h>
#include <linux/types.h>
#include <linux/errno.h>
#include <linux/kernel.h>
......
This diff is collapsed.
......@@ -66,7 +66,7 @@ ENTRY(omap1510_idle_loop_suspend)
@ get ARM_IDLECT2 into r2
ldrh r2, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
mov r5, #OMAP1510_IDLE_CLOCK_DOMAINS & 0xff
orr r5,r5, #OMAP1510_IDLE_CLOCK_DOMAINS & 0xff00
orr r5, r5, #OMAP1510_IDLE_CLOCK_DOMAINS & 0xff00
strh r5, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
@ request ARM idle
......@@ -76,7 +76,7 @@ ENTRY(omap1510_idle_loop_suspend)
strh r3, [r4, #ARM_IDLECT1_ASM_OFFSET & 0xff]
mov r5, #IDLE_WAIT_CYCLES & 0xff
orr r5, r5, #IDLE_WAIT_CYCLES & 0xff00
orr r5, r5, #IDLE_WAIT_CYCLES & 0xff00
l_1510: subs r5, r5, #1
bne l_1510
/*
......@@ -96,7 +96,7 @@ l_1510: subs r5, r5, #1
strh r2, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
strh r1, [r4, #ARM_IDLECT1_ASM_OFFSET & 0xff]
ldmfd sp!, {r0 - r12, pc} @ restore regs and return
ldmfd sp!, {r0 - r12, pc} @ restore regs and return
ENTRY(omap1510_idle_loop_suspend_sz)
.word . - omap1510_idle_loop_suspend
......@@ -115,8 +115,8 @@ ENTRY(omap1610_idle_loop_suspend)
@ turn off clock domains
@ get ARM_IDLECT2 into r2
ldrh r2, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
mov r5, #OMAP1610_IDLE_CLOCK_DOMAINS & 0xff
orr r5,r5, #OMAP1610_IDLE_CLOCK_DOMAINS & 0xff00
mov r5, #OMAP1610_IDLECT2_SLEEP_VAL & 0xff
orr r5, r5, #OMAP1610_IDLECT2_SLEEP_VAL & 0xff00
strh r5, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
@ request ARM idle
......@@ -126,7 +126,7 @@ ENTRY(omap1610_idle_loop_suspend)
strh r3, [r4, #ARM_IDLECT1_ASM_OFFSET & 0xff]
mov r5, #IDLE_WAIT_CYCLES & 0xff
orr r5, r5, #IDLE_WAIT_CYCLES & 0xff00
orr r5, r5, #IDLE_WAIT_CYCLES & 0xff00
l_1610: subs r5, r5, #1
bne l_1610
/*
......@@ -146,7 +146,7 @@ l_1610: subs r5, r5, #1
strh r2, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
strh r1, [r4, #ARM_IDLECT1_ASM_OFFSET & 0xff]
ldmfd sp!, {r0 - r12, pc} @ restore regs and return
ldmfd sp!, {r0 - r12, pc} @ restore regs and return
ENTRY(omap1610_idle_loop_suspend_sz)
.word . - omap1610_idle_loop_suspend
......@@ -208,7 +208,7 @@ ENTRY(omap1510_cpu_suspend)
@ turn off clock domains
mov r5, #OMAP1510_IDLE_CLOCK_DOMAINS & 0xff
orr r5,r5, #OMAP1510_IDLE_CLOCK_DOMAINS & 0xff00
orr r5, r5, #OMAP1510_IDLE_CLOCK_DOMAINS & 0xff00
strh r5, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
@ request ARM idle
......@@ -217,7 +217,7 @@ ENTRY(omap1510_cpu_suspend)
strh r3, [r4, #ARM_IDLECT1_ASM_OFFSET & 0xff]
mov r5, #IDLE_WAIT_CYCLES & 0xff
orr r5, r5, #IDLE_WAIT_CYCLES & 0xff00
orr r5, r5, #IDLE_WAIT_CYCLES & 0xff00
l_1510_2:
subs r5, r5, #1
bne l_1510_2
......@@ -237,7 +237,7 @@ l_1510_2:
strh r0, [r4, #ARM_IDLECT1_ASM_OFFSET & 0xff]
@ restore regs and return
ldmfd sp!, {r0 - r12, pc}
ldmfd sp!, {r0 - r12, pc}
ENTRY(omap1510_cpu_suspend_sz)
.word . - omap1510_cpu_suspend
......@@ -249,21 +249,26 @@ ENTRY(omap1610_cpu_suspend)
@ save registers on stack
stmfd sp!, {r0 - r12, lr}
@ Drain write cache
mov r4, #0
mcr p15, 0, r0, c7, c10, 4
nop
@ load base address of Traffic Controller
mov r4, #TCMIF_ASM_BASE & 0xff000000
orr r4, r4, #TCMIF_ASM_BASE & 0x00ff0000
orr r4, r4, #TCMIF_ASM_BASE & 0x0000ff00
mov r6, #TCMIF_ASM_BASE & 0xff000000
orr r6, r6, #TCMIF_ASM_BASE & 0x00ff0000
orr r6, r6, #TCMIF_ASM_BASE & 0x0000ff00
@ prepare to put SDRAM into self-refresh manually
ldr r5, [r4, #EMIFF_SDRAM_CONFIG_ASM_OFFSET & 0xff]
orr r5, r5, #SELF_REFRESH_MODE & 0xff000000
orr r5, r5, #SELF_REFRESH_MODE & 0x000000ff
str r5, [r4, #EMIFF_SDRAM_CONFIG_ASM_OFFSET & 0xff]
ldr r7, [r6, #EMIFF_SDRAM_CONFIG_ASM_OFFSET & 0xff]
orr r9, r7, #SELF_REFRESH_MODE & 0xff000000
orr r9, r9, #SELF_REFRESH_MODE & 0x000000ff
str r9, [r6, #EMIFF_SDRAM_CONFIG_ASM_OFFSET & 0xff]
@ prepare to put EMIFS to Sleep
ldr r5, [r4, #EMIFS_CONFIG_ASM_OFFSET & 0xff]
orr r5, r5, #IDLE_EMIFS_REQUEST & 0xff
str r5, [r4, #EMIFS_CONFIG_ASM_OFFSET & 0xff]
ldr r8, [r6, #EMIFS_CONFIG_ASM_OFFSET & 0xff]
orr r9, r8, #IDLE_EMIFS_REQUEST & 0xff
str r9, [r6, #EMIFS_CONFIG_ASM_OFFSET & 0xff]
@ load base address of ARM_IDLECT1 and ARM_IDLECT2
mov r4, #CLKGEN_REG_ASM_BASE & 0xff000000
......@@ -271,26 +276,22 @@ ENTRY(omap1610_cpu_suspend)
orr r4, r4, #CLKGEN_REG_ASM_BASE & 0x0000ff00
@ turn off clock domains
mov r5, #OMAP1610_IDLE_CLOCK_DOMAINS & 0xff
orr r5,r5, #OMAP1610_IDLE_CLOCK_DOMAINS & 0xff00
strh r5, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
@ work around errata of OMAP1610/5912. Enable (!) peripheral
@ clock to let the chip go into deep sleep
ldrh r5, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
orr r5,r5, #EN_PERCK_BIT & 0xff
@ do not disable PERCK (0x04)
mov r5, #OMAP1610_IDLECT2_SLEEP_VAL & 0xff
orr r5, r5, #OMAP1610_IDLECT2_SLEEP_VAL & 0xff00
strh r5, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
@ request ARM idle
mov r3, #OMAP1610_DEEP_SLEEP_REQUEST & 0xff
orr r3, r3, #OMAP1610_DEEP_SLEEP_REQUEST & 0xff00
mov r3, #OMAP1610_IDLECT1_SLEEP_VAL & 0xff
orr r3, r3, #OMAP1610_IDLECT1_SLEEP_VAL & 0xff00
strh r3, [r4, #ARM_IDLECT1_ASM_OFFSET & 0xff]
mov r5, #IDLE_WAIT_CYCLES & 0xff
orr r5, r5, #IDLE_WAIT_CYCLES & 0xff00
l_1610_2:
subs r5, r5, #1
bne l_1610_2
@ disable instruction cache
mrc p15, 0, r9, c1, c0, 0
bic r2, r9, #0x1000
mcr p15, 0, r2, c1, c0, 0
nop
/*
* Let's wait for the next wake up event to wake us up. r0 can't be
* used here because r0 holds ARM_IDLECT1
......@@ -301,13 +302,21 @@ l_1610_2:
* omap1610_cpu_suspend()'s resume point.
*
* It will just start executing here, so we'll restore stuff from the
* stack, reset the ARM_IDLECT1 and ARM_IDLECT2.
* stack.
*/
@ re-enable Icache
mcr p15, 0, r9, c1, c0, 0
@ reset the ARM_IDLECT1 and ARM_IDLECT2.
strh r1, [r4, #ARM_IDLECT2_ASM_OFFSET & 0xff]
strh r0, [r4, #ARM_IDLECT1_ASM_OFFSET & 0xff]
@ Restore EMIFF controls
str r7, [r6, #EMIFF_SDRAM_CONFIG_ASM_OFFSET & 0xff]
str r8, [r6, #EMIFS_CONFIG_ASM_OFFSET & 0xff]
@ restore regs and return
ldmfd sp!, {r0 - r12, pc}
ldmfd sp!, {r0 - r12, pc}
ENTRY(omap1610_cpu_suspend_sz)
.word . - omap1610_cpu_suspend
......
/*
* linux/arch/arm/plat-omap/sram.S
*
* Functions that need to be run in internal SRAM
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/config.h>
#include <linux/linkage.h>
#include <asm/assembler.h>
#include <asm/arch/io.h>
#include <asm/arch/hardware.h>
.text
/*
* Reprograms ULPD and CKCTL.
*/
ENTRY(sram_reprogram_clock)
stmfd sp!, {r0 - r12, lr} @ save registers on stack
mov r2, #IO_ADDRESS(DPLL_CTL) & 0xff000000
orr r2, r2, #IO_ADDRESS(DPLL_CTL) & 0x00ff0000
orr r2, r2, #IO_ADDRESS(DPLL_CTL) & 0x0000ff00
mov r3, #IO_ADDRESS(ARM_CKCTL) & 0xff000000
orr r3, r3, #IO_ADDRESS(ARM_CKCTL) & 0x00ff0000
orr r3, r3, #IO_ADDRESS(ARM_CKCTL) & 0x0000ff00
tst r0, #1 << 4 @ want lock mode?
beq newck @ nope
bic r0, r0, #1 << 4 @ else clear lock bit
strh r0, [r2] @ set dpll into bypass mode
orr r0, r0, #1 << 4 @ set lock bit again
newck:
strh r1, [r3] @ write new ckctl value
strh r0, [r2] @ write new dpll value
mov r4, #0x0700 @ let the clocks settle
orr r4, r4, #0x00ff
delay: sub r4, r4, #1
cmp r4, #0
bne delay
lock: ldrh r4, [r2], #0 @ read back dpll value
tst r0, #1 << 4 @ want lock mode?
beq out @ nope
tst r4, #1 << 0 @ dpll rate locked?
beq lock @ try again
out:
ldmfd sp!, {r0 - r12, pc} @ restore regs and return
ENTRY(sram_reprogram_clock_sz)
.word . - sram_reprogram_clock
/*
* linux/arch/arm/plat-omap/sram.c
*
* OMAP SRAM detection and management
*
* Copyright (C) 2005 Nokia Corporation
* Written by Tony Lindgren <tony@atomide.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/config.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <asm/mach/map.h>
#include <asm/io.h>
#include <asm/cacheflush.h>
#include "sram.h"
#define OMAP1_SRAM_BASE 0xd0000000
#define OMAP1_SRAM_START 0x20000000
#define SRAM_BOOTLOADER_SZ 0x80
static unsigned long omap_sram_base;
static unsigned long omap_sram_size;
static unsigned long omap_sram_ceil;
/*
* The amount of SRAM depends on the core type:
* 730 = 200K, 1510 = 512K, 5912 = 256K, 1610 = 16K, 1710 = 16K
* Note that we cannot try to test for SRAM here because writes
* to secure SRAM will hang the system. Also the SRAM is not
* yet mapped at this point.
*/
void __init omap_detect_sram(void)
{
omap_sram_base = OMAP1_SRAM_BASE;
if (cpu_is_omap730())
omap_sram_size = 0x32000;
else if (cpu_is_omap1510())
omap_sram_size = 0x80000;
else if (cpu_is_omap1610() || cpu_is_omap1621() || cpu_is_omap1710())
omap_sram_size = 0x4000;
else if (cpu_is_omap1611())
omap_sram_size = 0x3e800;
else {
printk(KERN_ERR "Could not detect SRAM size\n");
omap_sram_size = 0x4000;
}
printk(KERN_INFO "SRAM size: 0x%lx\n", omap_sram_size);
omap_sram_ceil = omap_sram_base + omap_sram_size;
}
static struct map_desc omap_sram_io_desc[] __initdata = {
{ OMAP1_SRAM_BASE, OMAP1_SRAM_START, 0, MT_DEVICE }
};
/*
* In order to use last 2kB of SRAM on 1611b, we must round the size
* up to multiple of PAGE_SIZE. We cannot use ioremap for SRAM, as
* clock init needs SRAM early.
*/
void __init omap_map_sram(void)
{
if (omap_sram_size == 0)
return;
omap_sram_io_desc[0].length = (omap_sram_size + PAGE_SIZE-1)/PAGE_SIZE;
omap_sram_io_desc[0].length *= PAGE_SIZE;
iotable_init(omap_sram_io_desc, ARRAY_SIZE(omap_sram_io_desc));
/*
* Looks like we need to preserve some bootloader code at the
* beginning of SRAM for jumping to flash for reboot to work...
*/
memset((void *)omap_sram_base + SRAM_BOOTLOADER_SZ, 0,
omap_sram_size - SRAM_BOOTLOADER_SZ);
}
static void (*_omap_sram_reprogram_clock)(u32 dpllctl, u32 ckctl) = NULL;
void omap_sram_reprogram_clock(u32 dpllctl, u32 ckctl)
{
if (_omap_sram_reprogram_clock == NULL)
panic("Cannot use SRAM");
return _omap_sram_reprogram_clock(dpllctl, ckctl);
}
void * omap_sram_push(void * start, unsigned long size)
{
if (size > (omap_sram_ceil - (omap_sram_base + SRAM_BOOTLOADER_SZ))) {
printk(KERN_ERR "Not enough space in SRAM\n");
return NULL;
}
omap_sram_ceil -= size;
omap_sram_ceil &= ~0x3;
memcpy((void *)omap_sram_ceil, start, size);
return (void *)omap_sram_ceil;
}
void __init omap_sram_init(void)
{
omap_detect_sram();
omap_map_sram();
_omap_sram_reprogram_clock = omap_sram_push(sram_reprogram_clock,
sram_reprogram_clock_sz);
}
/*
* linux/arch/arm/plat-omap/sram.h
*
* Interface for functions that need to be run in internal SRAM
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#ifndef __ARCH_ARM_OMAP_SRAM_H
#define __ARCH_ARM_OMAP_SRAM_H
extern void * omap_sram_push(void * start, unsigned long size);
extern void omap_sram_reprogram_clock(u32 dpllctl, u32 ckctl);
/* Do not use these */
extern void sram_reprogram_clock(u32 ckctl, u32 dpllctl);
extern unsigned long sram_reprogram_clock_sz;
#endif
......@@ -41,6 +41,7 @@
/* These routines should handle the standard chip-specific modes
* for usb0/1/2 ports, covering basic mux and transceiver setup.
* Call omap_usb_init() once, from INIT_MACHINE().
*
* Some board-*.c files will need to set up additional mux options,
* like for suspend handling, vbus sensing, GPIOs, and the D+ pullup.
......
......@@ -30,6 +30,9 @@
#define __ASM_ARCH_OMAP_H4_H
/* Placeholder for H4 specific defines */
/* GPMC CS1 */
#define OMAP24XX_ETHR_START 0x08000300
#define OMAP24XX_ETHR_GPIO_IRQ 92
#endif /* __ASM_ARCH_OMAP_H4_H */
......@@ -36,31 +36,6 @@
#define OMAP1510P1_EMIFS_PRI_VALUE 0x00
#define OMAP1510P1_EMIFF_PRI_VALUE 0x00
/*
* These definitions define an area of FLASH set aside
* for the use of MTD/JFFS2. This is the area of flash
* that a JFFS2 filesystem will reside which is mounted
* at boot with the "root=/dev/mtdblock/0 rw"
* command line option. The flash address used here must
* fall within the legal range defined by rrload for storing
* the filesystem component. This address will be sufficiently
* deep into the overall flash range to avoid the other
* components also stored in flash such as the bootloader,
* the bootloader params, and the kernel.
* The SW2 settings for the map below are:
* 1 off, 2 off, 3 on, 4 off.
*/
/* Intel flash_0, partitioned as expected by rrload */
#define OMAP_FLASH_0_BASE 0xD8000000
#define OMAP_FLASH_0_START 0x00000000
#define OMAP_FLASH_0_SIZE SZ_16M
/* Intel flash_1, used for cramfs or other flash file systems */
#define OMAP_FLASH_1_BASE 0xD9000000
#define OMAP_FLASH_1_START 0x01000000
#define OMAP_FLASH_1_SIZE SZ_16M
#define NR_FPGA_IRQS 24
#define NR_IRQS IH_BOARD_BASE + NR_FPGA_IRQS
......
......@@ -36,23 +36,14 @@
#define OMAP_SDRAM_DEVICE D256M_1X16_4B
#endif
/*
* These definitions define an area of FLASH set aside
* for the use of MTD/JFFS2. This is the area of flash
* that a JFFS2 filesystem will reside which is mounted
* at boot with the "root=/dev/mtdblock/0 rw"
* command line option.
*/
/* Intel flash_0, partitioned as expected by rrload */
#define OMAP_FLASH_0_BASE 0xD8000000 /* VA */
#define OMAP_FLASH_0_START 0x00000000 /* PA */
#define OMAP_FLASH_0_SIZE SZ_32M
#define MAXIRQNUM IH_BOARD_BASE
#define MAXFIQNUM MAXIRQNUM
#define MAXSWINUM MAXIRQNUM
#define NR_IRQS (MAXIRQNUM + 1)
/* Samsung NAND flash at CS2B or CS3(NAND Boot) */
#define OMAP_NAND_FLASH_START1 0x0A000000 /* CS2B */
#define OMAP_NAND_FLASH_START2 0x0C000000 /* CS3 */
#endif
......@@ -11,11 +11,6 @@
#ifndef __ASM_ARCH_VOICEBLUE_H
#define __ASM_ARCH_VOICEBLUE_H
#if (EXTERNAL_MAX_NR_PORTS < 4)
#undef EXTERNAL_MAX_NR_PORTS
#define EXTERNAL_MAX_NR_PORTS 4
#endif
extern void voiceblue_wdt_enable(void);
extern void voiceblue_wdt_disable(void);
extern void voiceblue_wdt_ping(void);
......
......@@ -30,10 +30,23 @@ struct omap_clock_config {
u8 system_clock_type;
};
struct omap_mmc_conf {
unsigned enabled:1;
/* nomux means "standard" muxing is wrong on this board, and that
* board-specific code handled it before common init logic.
*/
unsigned nomux:1;
/* switch pin can be for card detect (default) or card cover */
unsigned cover:1;
/* 4 wire signaling is optional, and is only used for SD/SDIO */
unsigned wire4:1;
s16 power_pin;
s16 switch_pin;
s16 wp_pin;
};
struct omap_mmc_config {
u8 mmc_blocks;
s16 mmc1_power_pin, mmc2_power_pin;
s16 mmc1_switch_pin, mmc2_switch_pin;
struct omap_mmc_conf mmc[2];
};
struct omap_serial_console_config {
......
......@@ -38,146 +38,179 @@ extern unsigned int system_rev;
/*
* Test if multicore OMAP support is needed
*/
#undef MULTI_OMAP
#undef MULTI_OMAP1
#undef MULTI_OMAP2
#undef OMAP_NAME
#ifdef CONFIG_ARCH_OMAP730
# ifdef OMAP_NAME
# undef MULTI_OMAP
# define MULTI_OMAP
# undef MULTI_OMAP1
# define MULTI_OMAP1
# else
# define OMAP_NAME omap730
# endif
#endif
#ifdef CONFIG_ARCH_OMAP1510
# ifdef OMAP_NAME
# undef MULTI_OMAP
# define MULTI_OMAP
# undef MULTI_OMAP1
# define MULTI_OMAP1
# else
# define OMAP_NAME omap1510
# endif
#endif
#ifdef CONFIG_ARCH_OMAP16XX
# ifdef OMAP_NAME
# undef MULTI_OMAP
# define MULTI_OMAP
# undef MULTI_OMAP1
# define MULTI_OMAP1
# else
# define OMAP_NAME omap1610
# define OMAP_NAME omap16xx
# endif
#endif
#ifdef CONFIG_ARCH_OMAP16XX
# ifdef OMAP_NAME
# undef MULTI_OMAP
# define MULTI_OMAP
#ifdef CONFIG_ARCH_OMAP24XX
# if (defined(OMAP_NAME) || defined(MULTI_OMAP1))
# error "OMAP1 and OMAP2 can't be selected at the same time"
# else
# define OMAP_NAME omap1710
# undef MULTI_OMAP2
# define OMAP_NAME omap24xx
# endif
#endif
/*
* Generate various OMAP cpu specific macros, and cpu class
* specific macros
* Macros to group OMAP into cpu classes.
* These can be used in most places.
* cpu_is_omap7xx(): True for OMAP730
* cpu_is_omap15xx(): True for OMAP1510 and OMAP5910
* cpu_is_omap16xx(): True for OMAP1610, OMAP5912 and OMAP1710
* cpu_is_omap24xx(): True for OMAP2420
*/
#define GET_OMAP_TYPE ((system_rev >> 24) & 0xff)
#define GET_OMAP_CLASS (system_rev & 0xff)
#define IS_OMAP_TYPE(type, id) \
static inline int is_omap ##type (void) \
{ \
return (GET_OMAP_TYPE == (id)) ? 1 : 0; \
}
#define IS_OMAP_CLASS(class, id) \
static inline int is_omap ##class (void) \
{ \
return (GET_OMAP_CLASS == (id)) ? 1 : 0; \
}
IS_OMAP_TYPE(730, 0x07)
IS_OMAP_TYPE(1510, 0x15)
IS_OMAP_TYPE(1610, 0x16)
IS_OMAP_TYPE(5912, 0x16)
IS_OMAP_TYPE(1710, 0x17)
IS_OMAP_TYPE(2420, 0x24)
IS_OMAP_CLASS(7xx, 0x07)
IS_OMAP_CLASS(15xx, 0x15)
IS_OMAP_CLASS(16xx, 0x16)
IS_OMAP_CLASS(24xx, 0x24)
/*
* Macros to group OMAP types into cpu classes.
* These can be used in most places.
* cpu_is_omap15xx(): True for 1510 and 5910
* cpu_is_omap16xx(): True for 1610, 5912 and 1710
*/
#if defined(MULTI_OMAP)
# define cpu_is_omap7xx() is_omap7xx()
# define cpu_is_omap15xx() is_omap15xx()
# if !(defined(CONFIG_ARCH_OMAP1510) || defined(CONFIG_ARCH_OMAP730))
# define cpu_is_omap16xx() 1
# else
#define cpu_is_omap7xx() 0
#define cpu_is_omap15xx() 0
#define cpu_is_omap16xx() 0
#define cpu_is_omap24xx() 0
#if defined(MULTI_OMAP1)
# if defined(CONFIG_ARCH_OMAP730)
# undef cpu_is_omap7xx
# define cpu_is_omap7xx() is_omap7xx()
# endif
# if defined(CONFIG_ARCH_OMAP1510)
# undef cpu_is_omap15xx
# define cpu_is_omap15xx() is_omap15xx()
# endif
# if defined(CONFIG_ARCH_OMAP16XX)
# undef cpu_is_omap16xx
# define cpu_is_omap16xx() is_omap16xx()
# endif
#else
# if defined(CONFIG_ARCH_OMAP730)
# undef cpu_is_omap7xx
# define cpu_is_omap7xx() 1
# else
# define cpu_is_omap7xx() 0
# endif
# if defined(CONFIG_ARCH_OMAP1510)
# undef cpu_is_omap15xx
# define cpu_is_omap15xx() 1
# else
# define cpu_is_omap15xx() 0
# endif
# if defined(CONFIG_ARCH_OMAP16XX)
# undef cpu_is_omap16xx
# define cpu_is_omap16xx() 1
# else
# define cpu_is_omap16xx() 0
# endif
# if defined(CONFIG_ARCH_OMAP24XX)
# undef cpu_is_omap24xx
# define cpu_is_omap24xx() 1
# endif
#endif
#if defined(MULTI_OMAP)
# define cpu_is_omap730() is_omap730()
# define cpu_is_omap1510() is_omap1510()
# define cpu_is_omap1610() is_omap1610()
# define cpu_is_omap5912() is_omap5912()
# define cpu_is_omap1710() is_omap1710()
/*
* Macros to detect individual cpu types.
* These are only rarely needed.
* cpu_is_omap730(): True for OMAP730
* cpu_is_omap1510(): True for OMAP1510
* cpu_is_omap1610(): True for OMAP1610
* cpu_is_omap1611(): True for OMAP1611
* cpu_is_omap5912(): True for OMAP5912
* cpu_is_omap1621(): True for OMAP1621
* cpu_is_omap1710(): True for OMAP1710
* cpu_is_omap2420(): True for OMAP2420
*/
#define GET_OMAP_TYPE ((system_rev >> 16) & 0xffff)
#define IS_OMAP_TYPE(type, id) \
static inline int is_omap ##type (void) \
{ \
return (GET_OMAP_TYPE == (id)) ? 1 : 0; \
}
IS_OMAP_TYPE(730, 0x0730)
IS_OMAP_TYPE(1510, 0x1510)
IS_OMAP_TYPE(1610, 0x1610)
IS_OMAP_TYPE(1611, 0x1611)
IS_OMAP_TYPE(5912, 0x1611)
IS_OMAP_TYPE(1621, 0x1621)
IS_OMAP_TYPE(1710, 0x1710)
IS_OMAP_TYPE(2420, 0x2420)
#define cpu_is_omap730() 0
#define cpu_is_omap1510() 0
#define cpu_is_omap1610() 0
#define cpu_is_omap5912() 0
#define cpu_is_omap1611() 0
#define cpu_is_omap1621() 0
#define cpu_is_omap1710() 0
#define cpu_is_omap2420() 0
#if defined(MULTI_OMAP1)
# if defined(CONFIG_ARCH_OMAP730)
# undef cpu_is_omap730
# define cpu_is_omap730() is_omap730()
# endif
# if defined(CONFIG_ARCH_OMAP1510)
# undef cpu_is_omap1510
# define cpu_is_omap1510() is_omap1510()
# endif
#else
# if defined(CONFIG_ARCH_OMAP730)
# undef cpu_is_omap730
# define cpu_is_omap730() 1
# else
# define cpu_is_omap730() 0
# endif
# if defined(CONFIG_ARCH_OMAP1510)
# undef cpu_is_omap1510
# define cpu_is_omap1510() 1
# else
# define cpu_is_omap1510() 0
# endif
# if defined(CONFIG_ARCH_OMAP16XX)
# define cpu_is_omap1610() 1
# else
# define cpu_is_omap1610() 0
# endif
# if defined(CONFIG_ARCH_OMAP16XX)
# define cpu_is_omap5912() 1
# else
# define cpu_is_omap5912() 0
# endif
# if defined(CONFIG_ARCH_OMAP16XX)
#endif
/*
* Whether we have MULTI_OMAP1 or not, we still need to distinguish
* between 1611B/5912 and 1710.
*/
#if defined(CONFIG_ARCH_OMAP16XX)
# undef cpu_is_omap1610
# undef cpu_is_omap1611
# undef cpu_is_omap5912
# undef cpu_is_omap1621
# undef cpu_is_omap1710
# define cpu_is_omap1610() is_omap1610()
# define cpu_is_omap1611() is_omap1611()
# define cpu_is_omap5912() is_omap5912()
# define cpu_is_omap1621() is_omap1621()
# define cpu_is_omap1710() is_omap1710()
# else
# define cpu_is_omap1610() 0
# define cpu_is_omap5912() 0
# define cpu_is_omap1710() 0
# endif
# if defined(CONFIG_ARCH_OMAP2420)
#endif
#if defined(CONFIG_ARCH_OMAP2420)
# undef cpu_is_omap2420
# define cpu_is_omap2420() 1
# else
# define cpu_is_omap2420() 0
# endif
#endif
#endif
......@@ -14,6 +14,7 @@
.macro addruart,rx
mrc p15, 0, \rx, c1, c0
tst \rx, #1 @ MMU enabled?
#ifdef CONFIG_ARCH_OMAP1
moveq \rx, #0xff000000 @ physical base address
movne \rx, #0xfe000000 @ virtual base
orr \rx, \rx, #0x00fb0000
......@@ -22,6 +23,18 @@
#endif
#if defined(CONFIG_OMAP_LL_DEBUG_UART2) || defined(CONFIG_OMAP_LL_DEBUG_UART3)
orr \rx, \rx, #0x00000800 @ UART 2 & 3
#endif
#elif CONFIG_ARCH_OMAP2
moveq \rx, #0x48000000 @ physical base address
movne \rx, #0xd8000000 @ virtual base
orr \rx, \rx, #0x0006a000
#ifdef CONFIG_OMAP_LL_DEBUG_UART2
add \rx, \rx, #0x00002000 @ UART 2
#endif
#ifdef CONFIG_OMAP_LL_DEBUG_UART3
add \rx, \rx, #0x00004000 @ UART 3
#endif
#endif
.endm
......
......@@ -240,6 +240,7 @@ extern void omap_dma_unlink_lch (int lch_head, int lch_queue);
extern dma_addr_t omap_get_dma_src_pos(int lch);
extern dma_addr_t omap_get_dma_dst_pos(int lch);
extern int omap_get_dma_src_addr_counter(int lch);
extern void omap_clear_dma(int lch);
extern int omap_dma_running(void);
......
/*
* linux/include/asm-arm/arm/arch-omap/dmtimer.h
*
* OMAP Dual-Mode Timers
*
* Copyright (C) 2005 Nokia Corporation
* Author: Lauri Leukkunen <lauri.leukkunen@nokia.com>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*
* THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
* NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 675 Mass Ave, Cambridge, MA 02139, USA.
*/
#ifndef __ASM_ARCH_TIMER_H
#define __ASM_ARCH_TIMER_H
#include <linux/list.h>
#define OMAP_TIMER_SRC_ARMXOR 0x00
#define OMAP_TIMER_SRC_32_KHZ 0x01
#define OMAP_TIMER_SRC_EXT_CLK 0x02
/* timer control reg bits */
#define OMAP_TIMER_CTRL_CAPTMODE (1 << 13)
#define OMAP_TIMER_CTRL_PT (1 << 12)
#define OMAP_TIMER_CTRL_TRG_OVERFLOW (0x1 << 10)
#define OMAP_TIMER_CTRL_TRG_OFANDMATCH (0x2 << 10)
#define OMAP_TIMER_CTRL_TCM_LOWTOHIGH (0x1 << 8)
#define OMAP_TIMER_CTRL_TCM_HIGHTOLOW (0x2 << 8)
#define OMAP_TIMER_CTRL_TCM_BOTHEDGES (0x3 << 8)
#define OMAP_TIMER_CTRL_SCPWM (1 << 7)
#define OMAP_TIMER_CTRL_CE (1 << 6) /* compare enable */
#define OMAP_TIMER_CTRL_PRE (1 << 5) /* prescaler enable */
#define OMAP_TIMER_CTRL_PTV_SHIFT 2 /* how much to shift the prescaler value */
#define OMAP_TIMER_CTRL_AR (1 << 1) /* auto-reload enable */
#define OMAP_TIMER_CTRL_ST (1 << 0) /* start timer */
/* timer interrupt enable bits */
#define OMAP_TIMER_INT_CAPTURE (1 << 2)
#define OMAP_TIMER_INT_OVERFLOW (1 << 1)
#define OMAP_TIMER_INT_MATCH (1 << 0)
struct omap_dm_timer {
struct list_head timer_list;
u32 base;
unsigned int irq;
};
u32 omap_dm_timer_read_reg(struct omap_dm_timer *timer, int reg);
void omap_dm_timer_write_reg(struct omap_dm_timer *timer, int reg, u32 value);
struct omap_dm_timer * omap_dm_timer_request(void);
void omap_dm_timer_free(struct omap_dm_timer *timer);
void omap_dm_timer_set_source(struct omap_dm_timer *timer, int source);
void omap_dm_timer_set_int_enable(struct omap_dm_timer *timer, unsigned int value);
void omap_dm_timer_set_trigger(struct omap_dm_timer *timer, unsigned int value);
void omap_dm_timer_enable_compare(struct omap_dm_timer *timer);
void omap_dm_timer_enable_autoreload(struct omap_dm_timer *timer);
void omap_dm_timer_trigger(struct omap_dm_timer *timer);
void omap_dm_timer_start(struct omap_dm_timer *timer);
void omap_dm_timer_stop(struct omap_dm_timer *timer);
void omap_dm_timer_set_load(struct omap_dm_timer *timer, unsigned int load);
void omap_dm_timer_set_match(struct omap_dm_timer *timer, unsigned int match);
unsigned int omap_dm_timer_read_status(struct omap_dm_timer *timer);
void omap_dm_timer_write_status(struct omap_dm_timer *timer, unsigned int value);
unsigned int omap_dm_timer_read_counter(struct omap_dm_timer *timer);
void omap_dm_timer_reset_counter(struct omap_dm_timer *timer);
int omap_dm_timers_active(void);
#endif /* __ASM_ARCH_TIMER_H */
/*
* linux/include/asm-arm/arch-omap/dsp.h
*
* Header for OMAP DSP driver
*
* Copyright (C) 2002-2005 Nokia Corporation
*
* Written by Toshihiro Kobayashi <toshihiro.kobayashi@nokia.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
* 2005/06/01: DSP Gateway version 3.3
*/
#ifndef ASM_ARCH_DSP_H
#define ASM_ARCH_DSP_H
/*
* for /dev/dspctl/ctl
*/
#define OMAP_DSP_IOCTL_RESET 1
#define OMAP_DSP_IOCTL_RUN 2
#define OMAP_DSP_IOCTL_SETRSTVECT 3
#define OMAP_DSP_IOCTL_CPU_IDLE 4
#define OMAP_DSP_IOCTL_MPUI_WORDSWAP_ON 5
#define OMAP_DSP_IOCTL_MPUI_WORDSWAP_OFF 6
#define OMAP_DSP_IOCTL_MPUI_BYTESWAP_ON 7
#define OMAP_DSP_IOCTL_MPUI_BYTESWAP_OFF 8
#define OMAP_DSP_IOCTL_GBL_IDLE 9
#define OMAP_DSP_IOCTL_DSPCFG 10
#define OMAP_DSP_IOCTL_DSPUNCFG 11
#define OMAP_DSP_IOCTL_TASKCNT 12
#define OMAP_DSP_IOCTL_POLL 13
#define OMAP_DSP_IOCTL_REGMEMR 40
#define OMAP_DSP_IOCTL_REGMEMW 41
#define OMAP_DSP_IOCTL_REGIOR 42
#define OMAP_DSP_IOCTL_REGIOW 43
#define OMAP_DSP_IOCTL_GETVAR 44
#define OMAP_DSP_IOCTL_SETVAR 45
#define OMAP_DSP_IOCTL_RUNLEVEL 50
#define OMAP_DSP_IOCTL_SUSPEND 51
#define OMAP_DSP_IOCTL_RESUME 52
#define OMAP_DSP_IOCTL_FBEN 53
#define OMAP_DSP_IOCTL_FBDIS 54
#define OMAP_DSP_IOCTL_MBSEND 99
/*
* for taskdev
* (ioctls below should be >= 0x10000)
*/
#define OMAP_DSP_TASK_IOCTL_BFLSH 0x10000
#define OMAP_DSP_TASK_IOCTL_SETBSZ 0x10001
#define OMAP_DSP_TASK_IOCTL_LOCK 0x10002
#define OMAP_DSP_TASK_IOCTL_UNLOCK 0x10003
#define OMAP_DSP_TASK_IOCTL_GETNAME 0x10004
/*
* for /dev/dspctl/mem
*/
#define OMAP_DSP_MEM_IOCTL_EXMAP 1
#define OMAP_DSP_MEM_IOCTL_EXUNMAP 2
#define OMAP_DSP_MEM_IOCTL_EXMAP_FLUSH 3
#define OMAP_DSP_MEM_IOCTL_FBEXPORT 5
#define OMAP_DSP_MEM_IOCTL_MMUITACK 7
#define OMAP_DSP_MEM_IOCTL_MMUINIT 9
#define OMAP_DSP_MEM_IOCTL_KMEM_RESERVE 11
#define OMAP_DSP_MEM_IOCTL_KMEM_RELEASE 12
struct omap_dsp_mapinfo {
unsigned long dspadr;
unsigned long size;
};
/*
* for /dev/dspctl/twch
*/
#define OMAP_DSP_TWCH_IOCTL_MKDEV 1
#define OMAP_DSP_TWCH_IOCTL_RMDEV 2
#define OMAP_DSP_TWCH_IOCTL_TADD 11
#define OMAP_DSP_TWCH_IOCTL_TDEL 12
#define OMAP_DSP_TWCH_IOCTL_TKILL 13
#define OMAP_DSP_DEVSTATE_NOTASK 0x00000001
#define OMAP_DSP_DEVSTATE_ATTACHED 0x00000002
#define OMAP_DSP_DEVSTATE_GARBAGE 0x00000004
#define OMAP_DSP_DEVSTATE_INVALID 0x00000008
#define OMAP_DSP_DEVSTATE_ADDREQ 0x00000100
#define OMAP_DSP_DEVSTATE_DELREQ 0x00000200
#define OMAP_DSP_DEVSTATE_ADDFAIL 0x00001000
#define OMAP_DSP_DEVSTATE_ADDING 0x00010000
#define OMAP_DSP_DEVSTATE_DELING 0x00020000
#define OMAP_DSP_DEVSTATE_KILLING 0x00040000
#define OMAP_DSP_DEVSTATE_STATE_MASK 0x7fffffff
#define OMAP_DSP_DEVSTATE_STALE 0x80000000
struct omap_dsp_taddinfo {
unsigned char minor;
unsigned long taskadr;
};
#define OMAP_DSP_TADD_ABORTADR 0xffffffff
/*
* error cause definition (for error detection device)
*/
#define OMAP_DSP_ERRDT_WDT 0x00000001
#define OMAP_DSP_ERRDT_MMU 0x00000002
/*
* mailbox protocol definitions
*/
struct omap_dsp_mailbox_cmd {
unsigned short cmd;
unsigned short data;
};
struct omap_dsp_reginfo {
unsigned short adr;
unsigned short val;
};
struct omap_dsp_varinfo {
unsigned char varid;
unsigned short val[0];
};
#define OMAP_DSP_MBPROT_REVISION 0x0019
#define OMAP_DSP_MBCMD_WDSND 0x10
#define OMAP_DSP_MBCMD_WDREQ 0x11
#define OMAP_DSP_MBCMD_BKSND 0x20
#define OMAP_DSP_MBCMD_BKREQ 0x21
#define OMAP_DSP_MBCMD_BKYLD 0x23
#define OMAP_DSP_MBCMD_BKSNDP 0x24
#define OMAP_DSP_MBCMD_BKREQP 0x25
#define OMAP_DSP_MBCMD_TCTL 0x30
#define OMAP_DSP_MBCMD_TCTLDATA 0x31
#define OMAP_DSP_MBCMD_POLL 0x32
#define OMAP_DSP_MBCMD_WDT 0x50 /* v3.3: obsolete */
#define OMAP_DSP_MBCMD_RUNLEVEL 0x51
#define OMAP_DSP_MBCMD_PM 0x52
#define OMAP_DSP_MBCMD_SUSPEND 0x53
#define OMAP_DSP_MBCMD_KFUNC 0x54
#define OMAP_DSP_MBCMD_TCFG 0x60
#define OMAP_DSP_MBCMD_TADD 0x62
#define OMAP_DSP_MBCMD_TDEL 0x63
#define OMAP_DSP_MBCMD_TSTOP 0x65
#define OMAP_DSP_MBCMD_DSPCFG 0x70
#define OMAP_DSP_MBCMD_REGRW 0x72
#define OMAP_DSP_MBCMD_GETVAR 0x74
#define OMAP_DSP_MBCMD_SETVAR 0x75
#define OMAP_DSP_MBCMD_ERR 0x78
#define OMAP_DSP_MBCMD_DBG 0x79
#define OMAP_DSP_MBCMD_TCTL_TINIT 0x0000
#define OMAP_DSP_MBCMD_TCTL_TEN 0x0001
#define OMAP_DSP_MBCMD_TCTL_TDIS 0x0002
#define OMAP_DSP_MBCMD_TCTL_TCLR 0x0003
#define OMAP_DSP_MBCMD_TCTL_TCLR_FORCE 0x0004
#define OMAP_DSP_MBCMD_RUNLEVEL_USER 0x01
#define OMAP_DSP_MBCMD_RUNLEVEL_SUPER 0x0e
#define OMAP_DSP_MBCMD_RUNLEVEL_RECOVERY 0x10
#define OMAP_DSP_MBCMD_PM_DISABLE 0x00
#define OMAP_DSP_MBCMD_PM_ENABLE 0x01
#define OMAP_DSP_MBCMD_KFUNC_FBCTL 0x00
#define OMAP_DSP_MBCMD_FBCTL_ENABLE 0x0002
#define OMAP_DSP_MBCMD_FBCTL_DISABLE 0x0003
#define OMAP_DSP_MBCMD_TDEL_SAFE 0x0000
#define OMAP_DSP_MBCMD_TDEL_KILL 0x0001
#define OMAP_DSP_MBCMD_DSPCFG_REQ 0x00
#define OMAP_DSP_MBCMD_DSPCFG_SYSADRH 0x28
#define OMAP_DSP_MBCMD_DSPCFG_SYSADRL 0x29
#define OMAP_DSP_MBCMD_DSPCFG_PROTREV 0x70
#define OMAP_DSP_MBCMD_DSPCFG_ABORT 0x78
#define OMAP_DSP_MBCMD_DSPCFG_LAST 0x80
#define OMAP_DSP_MBCMD_REGRW_MEMR 0x00
#define OMAP_DSP_MBCMD_REGRW_MEMW 0x01
#define OMAP_DSP_MBCMD_REGRW_IOR 0x02
#define OMAP_DSP_MBCMD_REGRW_IOW 0x03
#define OMAP_DSP_MBCMD_REGRW_DATA 0x04
#define OMAP_DSP_MBCMD_VARID_ICRMASK 0x00
#define OMAP_DSP_MBCMD_VARID_LOADINFO 0x01
#define OMAP_DSP_TTYP_ARCV 0x0001
#define OMAP_DSP_TTYP_ASND 0x0002
#define OMAP_DSP_TTYP_BKMD 0x0004
#define OMAP_DSP_TTYP_BKDM 0x0008
#define OMAP_DSP_TTYP_PVMD 0x0010
#define OMAP_DSP_TTYP_PVDM 0x0020
#define OMAP_DSP_EID_BADTID 0x10
#define OMAP_DSP_EID_BADTCN 0x11
#define OMAP_DSP_EID_BADBID 0x20
#define OMAP_DSP_EID_BADCNT 0x21
#define OMAP_DSP_EID_NOTLOCKED 0x22
#define OMAP_DSP_EID_STVBUF 0x23
#define OMAP_DSP_EID_BADADR 0x24
#define OMAP_DSP_EID_BADTCTL 0x30
#define OMAP_DSP_EID_BADPARAM 0x50
#define OMAP_DSP_EID_FATAL 0x58
#define OMAP_DSP_EID_NOMEM 0xc0
#define OMAP_DSP_EID_NORES 0xc1
#define OMAP_DSP_EID_IPBFULL 0xc2
#define OMAP_DSP_EID_WDT 0xd0
#define OMAP_DSP_EID_TASKNOTRDY 0xe0
#define OMAP_DSP_EID_TASKBSY 0xe1
#define OMAP_DSP_EID_TASKERR 0xef
#define OMAP_DSP_EID_BADCFGTYP 0xf0
#define OMAP_DSP_EID_DEBUG 0xf8
#define OMAP_DSP_EID_BADSEQ 0xfe
#define OMAP_DSP_EID_BADCMD 0xff
#define OMAP_DSP_TNM_LEN 16
#define OMAP_DSP_TID_FREE 0xff
#define OMAP_DSP_TID_ANON 0xfe
#define OMAP_DSP_BID_NULL 0xffff
#define OMAP_DSP_BID_PVT 0xfffe
#endif /* ASM_ARCH_DSP_H */
/*
* linux/include/asm-arm/arch-omap/dsp_common.h
*
* Header for OMAP DSP subsystem control
*
* Copyright (C) 2004,2005 Nokia Corporation
*
* Written by Toshihiro Kobayashi <toshihiro.kobayashi@nokia.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
* 2005/06/03: DSP Gateway version 3.3
*/
#ifndef ASM_ARCH_DSP_COMMON_H
#define ASM_ARCH_DSP_COMMON_H
void omap_dsp_pm_suspend(void);
void omap_dsp_pm_resume(void);
void omap_dsp_request_mpui(void);
void omap_dsp_release_mpui(void);
int omap_dsp_request_mem(void);
int omap_dsp_release_mem(void);
#endif /* ASM_ARCH_DSP_COMMON_H */
......@@ -8,6 +8,8 @@
* warranty of any kind, whether express or implied.
*/
#if defined(CONFIG_ARCH_OMAP1)
.macro disable_fiq
.endm
......@@ -30,3 +32,29 @@
1510:
.endm
#elif defined(CONFIG_ARCH_OMAP24XX)
#include <asm/arch/omap24xx.h>
.macro disable_fiq
.endm
.macro get_irqnr_and_base, irqnr, irqstat, base, tmp
ldr \base, =VA_IC_BASE
ldr \irqnr, [\base, #0x98] /* IRQ pending reg 1 */
cmp \irqnr, #0x0
bne 2222f
ldr \irqnr, [\base, #0xb8] /* IRQ pending reg 2 */
cmp \irqnr, #0x0
bne 2222f
ldr \irqnr, [\base, #0xd8] /* IRQ pending reg 3 */
cmp \irqnr, #0x0
2222:
ldrne \irqnr, [\base, #IRQ_SIR_IRQ]
.endm
.macro irq_prio_table
.endm
#endif
......@@ -3,7 +3,7 @@
*
* OMAP GPIO handling defines and functions
*
* Copyright (C) 2003 Nokia Corporation
* Copyright (C) 2003-2005 Nokia Corporation
*
* Written by Juha Yrjl <juha.yrjola@nokia.com>
*
......@@ -30,7 +30,23 @@
#include <asm/arch/irqs.h>
#include <asm/io.h>
#define OMAP_MPUIO_BASE 0xfffb5000
#define OMAP_MPUIO_BASE (void __iomem *)0xfffb5000
#ifdef CONFIG_ARCH_OMAP730
#define OMAP_MPUIO_INPUT_LATCH 0x00
#define OMAP_MPUIO_OUTPUT 0x02
#define OMAP_MPUIO_IO_CNTL 0x04
#define OMAP_MPUIO_KBR_LATCH 0x08
#define OMAP_MPUIO_KBC 0x0a
#define OMAP_MPUIO_GPIO_EVENT_MODE 0x0c
#define OMAP_MPUIO_GPIO_INT_EDGE 0x0e
#define OMAP_MPUIO_KBD_INT 0x10
#define OMAP_MPUIO_GPIO_INT 0x12
#define OMAP_MPUIO_KBD_MASKIT 0x14
#define OMAP_MPUIO_GPIO_MASKIT 0x16
#define OMAP_MPUIO_GPIO_DEBOUNCING 0x18
#define OMAP_MPUIO_LATCH 0x1a
#else
#define OMAP_MPUIO_INPUT_LATCH 0x00
#define OMAP_MPUIO_OUTPUT 0x04
#define OMAP_MPUIO_IO_CNTL 0x08
......@@ -44,6 +60,7 @@
#define OMAP_MPUIO_GPIO_MASKIT 0x2c
#define OMAP_MPUIO_GPIO_DEBOUNCING 0x30
#define OMAP_MPUIO_LATCH 0x34
#endif
#define OMAP_MPUIO(nr) (OMAP_MAX_GPIO_LINES + (nr))
#define OMAP_GPIO_IS_MPUIO(nr) ((nr) >= OMAP_MAX_GPIO_LINES)
......@@ -52,18 +69,11 @@
IH_MPUIO_BASE + ((nr) & 0x0f) : \
IH_GPIO_BASE + ((nr) & 0x3f))
/* For EDGECTRL */
#define OMAP_GPIO_NO_EDGE 0x00
#define OMAP_GPIO_FALLING_EDGE 0x01
#define OMAP_GPIO_RISING_EDGE 0x02
#define OMAP_GPIO_BOTH_EDGES 0x03
extern int omap_gpio_init(void); /* Call from board init only */
extern int omap_request_gpio(int gpio);
extern void omap_free_gpio(int gpio);
extern void omap_set_gpio_direction(int gpio, int is_input);
extern void omap_set_gpio_dataout(int gpio, int enable);
extern int omap_get_gpio_datain(int gpio);
extern void omap_set_gpio_edge_ctrl(int gpio, int edge);
#endif
......@@ -43,6 +43,7 @@
#include <asm/arch/cpu.h>
#endif
#include <asm/arch/io.h>
#include <asm/arch/serial.h>
/*
* ---------------------------------------------------------------------------
......@@ -89,11 +90,12 @@
/* DPLL control registers */
#define DPLL_CTL (0xfffecf00)
/* DSP clock control */
/* DSP clock control. Must use __raw_readw() and __raw_writew() with these */
#define DSP_CONFIG_REG_BASE (0xe1008000)
#define DSP_CKCTL (DSP_CONFIG_REG_BASE + 0x0)
#define DSP_IDLECT1 (DSP_CONFIG_REG_BASE + 0x4)
#define DSP_IDLECT2 (DSP_CONFIG_REG_BASE + 0x8)
#define DSP_RSTCT2 (DSP_CONFIG_REG_BASE + 0x14)
/*
* ---------------------------------------------------------------------------
......@@ -142,6 +144,13 @@
* Interrupts
* ---------------------------------------------------------------------------
*/
#ifdef CONFIG_ARCH_OMAP1
/*
* XXX: These probably want to be moved to arch/arm/mach-omap/omap1/irq.c
* or something similar.. -- PFM.
*/
#define OMAP_IH1_BASE 0xfffecb00
#define OMAP_IH2_BASE 0xfffe0000
......@@ -170,6 +179,8 @@
#define IRQ_ILR0_REG_OFFSET 0x1c
#define IRQ_GMR_REG_OFFSET 0xa0
#endif
/*
* ----------------------------------------------------------------------------
* System control registers
......@@ -258,26 +269,6 @@
#ifndef __ASSEMBLER__
/*
* ---------------------------------------------------------------------------
* Serial ports
* ---------------------------------------------------------------------------
*/
#define OMAP_UART1_BASE (unsigned char *)0xfffb0000
#define OMAP_UART2_BASE (unsigned char *)0xfffb0800
#define OMAP_UART3_BASE (unsigned char *)0xfffb9800
#define OMAP_MAX_NR_PORTS 3
#define OMAP1510_BASE_BAUD (12000000/16)
#define OMAP16XX_BASE_BAUD (48000000/16)
#define is_omap_port(p) ({int __ret = 0; \
if (p == IO_ADDRESS(OMAP_UART1_BASE) || \
p == IO_ADDRESS(OMAP_UART2_BASE) || \
p == IO_ADDRESS(OMAP_UART3_BASE)) \
__ret = 1; \
__ret; \
})
/*
* ---------------------------------------------------------------------------
* Processor specific defines
......@@ -286,6 +277,11 @@
#include "omap730.h"
#include "omap1510.h"
#ifdef CONFIG_ARCH_OMAP24XX
#include "omap24xx.h"
#endif
#include "omap16xx.h"
/*
......@@ -312,7 +308,6 @@
#ifdef CONFIG_MACH_OMAP_H4
#include "board-h4.h"
#error "Support for H4 board not yet implemented."
#endif
#ifdef CONFIG_MACH_OMAP_OSK
......
......@@ -49,16 +49,24 @@
* I/O mapping
* ----------------------------------------------------------------------------
*/
#define IO_PHYS 0xFFFB0000
#define IO_OFFSET 0x01000000 /* Virtual IO = 0xfefb0000 */
#define IO_VIRT (IO_PHYS - IO_OFFSET)
#define IO_SIZE 0x40000
#define IO_ADDRESS(x) ((x) - IO_OFFSET)
#define PCIO_BASE 0
#if defined(CONFIG_ARCH_OMAP1)
#define IO_PHYS 0xFFFB0000
#define IO_OFFSET -0x01000000 /* Virtual IO = 0xfefb0000 */
#define IO_SIZE 0x40000
#define io_p2v(x) ((x) - IO_OFFSET)
#define io_v2p(x) ((x) + IO_OFFSET)
#elif defined(CONFIG_ARCH_OMAP2)
#define IO_PHYS 0x48000000 /* L4 peripherals; other stuff has to be mapped *
* manually. */
#define IO_OFFSET 0x90000000 /* Virtual IO = 0xd8000000 */
#define IO_SIZE 0x08000000
#endif
#define IO_VIRT (IO_PHYS + IO_OFFSET)
#define IO_ADDRESS(x) ((x) + IO_OFFSET)
#define PCIO_BASE 0
#define io_p2v(x) ((x) + IO_OFFSET)
#define io_v2p(x) ((x) - IO_OFFSET)
#ifndef __ASSEMBLER__
......@@ -96,6 +104,8 @@ typedef struct { volatile u32 offset[4096]; } __regbase32;
->offset[((vaddr)&4095)>>2]
#define __REG32(paddr) __REGV32(io_p2v(paddr))
extern void omap_map_common_io(void);
#else
#define __REG8(paddr) io_p2v(paddr)
......
......@@ -135,7 +135,6 @@
/*
* OMAP-1510 specific IRQ numbers for interrupt handler 2
*/
#define INT_1510_OS_32kHz_TIMER (22 + IH2_BASE)
#define INT_1510_COM_SPI_RO (31 + IH2_BASE)
/*
......@@ -232,6 +231,11 @@
#define INT_730_DMA_CH15 (62 + IH2_BASE)
#define INT_730_NAND (63 + IH2_BASE)
#define INT_24XX_GPIO_BANK1 29
#define INT_24XX_GPIO_BANK2 30
#define INT_24XX_GPIO_BANK3 31
#define INT_24XX_GPIO_BANK4 32
/* Max. 128 level 2 IRQs (OMAP1610), 192 GPIOs (OMAP730) and
* 16 MPUIO lines */
#define OMAP_MAX_GPIO_LINES 192
......
......@@ -36,12 +36,11 @@
/*
* Physical DRAM offset.
*/
#if defined(CONFIG_ARCH_OMAP1)
#define PHYS_OFFSET (0x10000000UL)
/*
* OMAP-1510 Local Bus address offset
*/
#define OMAP1510_LB_OFFSET (0x30000000UL)
#elif defined(CONFIG_ARCH_OMAP2)
#define PHYS_OFFSET (0x80000000UL)
#endif
/*
* Conversion between SDRAM and fake PCI bus, used by USB
......@@ -64,6 +63,11 @@
*/
#ifdef CONFIG_ARCH_OMAP1510
/*
* OMAP-1510 Local Bus address offset
*/
#define OMAP1510_LB_OFFSET (0x30000000UL)
#define virt_to_lbus(x) ((x) - PAGE_OFFSET + OMAP1510_LB_OFFSET)
#define lbus_to_virt(x) ((x) - OMAP1510_LB_OFFSET + PAGE_OFFSET)
#define is_lbus_device(dev) (cpu_is_omap1510() && dev && (strncmp(dev->bus_id, "ohci", 4) == 0))
......
/*
* MTD primitives for XIP support. Architecture specific functions.
*
* Do not include this file directly. It's included from linux/mtd/xip.h
*
* Author: Vladimir Barinov <vbarinov@ru.mvista.com>
*
* (c) 2005 MontaVista Software, Inc. This file is licensed under the
* terms of the GNU General Public License version 2. This program is
* licensed "as is" without any warranty of any kind, whether express or
* implied.
*/
#ifndef __ARCH_OMAP_MTD_XIP_H__
#define __ARCH_OMAP_MTD_XIP_H__
#include <asm/hardware.h>
#define OMAP_MPU_TIMER_BASE (0xfffec500)
#define OMAP_MPU_TIMER_OFFSET 0x100
typedef struct {
u32 cntl; /* CNTL_TIMER, R/W */
u32 load_tim; /* LOAD_TIM, W */
u32 read_tim; /* READ_TIM, R */
} xip_omap_mpu_timer_regs_t;
#define xip_omap_mpu_timer_base(n) \
((volatile xip_omap_mpu_timer_regs_t*)IO_ADDRESS(OMAP_MPU_TIMER_BASE + \
(n)*OMAP_MPU_TIMER_OFFSET))
static inline unsigned long xip_omap_mpu_timer_read(int nr)
{
volatile xip_omap_mpu_timer_regs_t* timer = xip_omap_mpu_timer_base(nr);
return timer->read_tim;
}
#define xip_irqpending() \
(omap_readl(OMAP_IH1_ITR) & ~omap_readl(OMAP_IH1_MIR))
#define xip_currtime() (~xip_omap_mpu_timer_read(0))
/*
* It's permitted to do approxmation for xip_elapsed_since macro
* (see linux/mtd/xip.h)
*/
#ifdef CONFIG_MACH_OMAP_PERSEUS2
#define xip_elapsed_since(x) (signed)((~xip_omap_mpu_timer_read(0) - (x)) / 7)
#else
#define xip_elapsed_since(x) (signed)((~xip_omap_mpu_timer_read(0) - (x)) / 6)
#endif
/*
* xip_cpu_idle() is used when waiting for a delay equal or larger than
* the system timer tick period. This should put the CPU into idle mode
* to save power and to be woken up only when some interrupts are pending.
* As above, this should not rely upon standard kernel code.
*/
#define xip_cpu_idle() asm volatile ("mcr p15, 0, %0, c7, c0, 4" :: "r" (1))
#endif /* __ARCH_OMAP_MTD_XIP_H__ */
......@@ -185,6 +185,7 @@ typedef enum {
/* MPUIO */
MPUIO2,
N15_1610_MPUIO2,
MPUIO4,
MPUIO5,
T20_1610_MPUIO5,
......@@ -210,6 +211,7 @@ typedef enum {
/* Misc ballouts */
BALLOUT_V8_ARMIO3,
N20_HDQ,
/* OMAP-1610 MMC2 */
W8_1610_MMC2_DAT0,
......@@ -235,6 +237,7 @@ typedef enum {
P20_1610_GPIO4,
V9_1610_GPIO7,
W8_1610_GPIO9,
N20_1610_GPIO11,
N19_1610_GPIO13,
P10_1610_GPIO22,
V5_1610_GPIO24,
......@@ -250,7 +253,7 @@ typedef enum {
U18_1610_UWIRE_SDI,
W21_1610_UWIRE_SDO,
N14_1610_UWIRE_CS0,
P15_1610_UWIRE_CS0,
P15_1610_UWIRE_CS3,
N15_1610_UWIRE_CS1,
/* OMAP-1610 Flash */
......@@ -411,7 +414,8 @@ MUX_CFG("N21_1710_GPIO14", 6, 9, 0, 1, 1, 1, 1, 1, 1)
MUX_CFG("W15_1710_GPIO40", 9, 27, 7, 2, 5, 1, 2, 1, 1)
/* MPUIO */
MUX_CFG("MPUIO2", 7, 18, 0, 1, 1, 1, NA, 0, 1)
MUX_CFG("MPUIO2", 7, 18, 0, 1, 14, 1, NA, 0, 1)
MUX_CFG("N15_1610_MPUIO2", 7, 18, 0, 1, 14, 1, 1, 0, 1)
MUX_CFG("MPUIO4", 7, 15, 0, 1, 13, 1, NA, 0, 1)
MUX_CFG("MPUIO5", 7, 12, 0, 1, 12, 1, NA, 0, 1)
......@@ -438,6 +442,7 @@ MUX_CFG("MCBSP3_CLKX", 9, 3, 1, 1, 29, 0, NA, 0, 1)
/* Misc ballouts */
MUX_CFG("BALLOUT_V8_ARMIO3", B, 18, 0, 2, 25, 1, NA, 0, 1)
MUX_CFG("N20_HDQ", 6, 18, 1, 1, 4, 0, 1, 4, 0)
/* OMAP-1610 MMC2 */
MUX_CFG("W8_1610_MMC2_DAT0", B, 21, 6, 2, 23, 1, 2, 1, 1)
......@@ -463,6 +468,7 @@ MUX_CFG("J18_1610_ETM_D7", 5, 27, 1, 0, 19, 0, 0, 0, 1)
MUX_CFG("P20_1610_GPIO4", 6, 27, 0, 1, 7, 0, 1, 1, 1)
MUX_CFG("V9_1610_GPIO7", B, 12, 1, 2, 20, 0, 2, 1, 1)
MUX_CFG("W8_1610_GPIO9", B, 21, 0, 2, 23, 0, 2, 1, 1)
MUX_CFG("N20_1610_GPIO11", 6, 18, 0, 1, 4, 0, 1, 1, 1)
MUX_CFG("N19_1610_GPIO13", 6, 12, 0, 1, 2, 0, 1, 1, 1)
MUX_CFG("P10_1610_GPIO22", C, 0, 7, 2, 26, 0, 2, 1, 1)
MUX_CFG("V5_1610_GPIO24", B, 15, 7, 2, 21, 0, 2, 1, 1)
......
......@@ -36,10 +36,6 @@
/* Syntax: XX_BASE = Virtual base address, XX_START = Physical base address */
#define OMAP1510_SRAM_BASE 0xD0000000
#define OMAP1510_SRAM_SIZE (SZ_128K + SZ_64K)
#define OMAP1510_SRAM_START 0x20000000
#define OMAP1510_DSP_BASE 0xE0000000
#define OMAP1510_DSP_SIZE 0x28000
#define OMAP1510_DSP_START 0xE0000000
......@@ -48,14 +44,5 @@
#define OMAP1510_DSPREG_SIZE SZ_128K
#define OMAP1510_DSPREG_START 0xE1000000
/*
* ----------------------------------------------------------------------------
* Memory used by power management
* ----------------------------------------------------------------------------
*/
#define OMAP1510_SRAM_IDLE_SUSPEND (OMAP1510_SRAM_BASE + OMAP1510_SRAM_SIZE - 0x200)
#define OMAP1510_SRAM_API_SUSPEND (OMAP1510_SRAM_IDLE_SUSPEND + 0x100)
#endif /* __ASM_ARCH_OMAP1510_H */
......@@ -36,11 +36,6 @@
/* Syntax: XX_BASE = Virtual base address, XX_START = Physical base address */
#define OMAP16XX_SRAM_BASE 0xD0000000
#define OMAP1610_SRAM_SIZE (SZ_16K)
#define OMAP5912_SRAM_SIZE 0x3E800
#define OMAP16XX_SRAM_START 0x20000000
#define OMAP16XX_DSP_BASE 0xE0000000
#define OMAP16XX_DSP_SIZE 0x28000
#define OMAP16XX_DSP_START 0xE0000000
......@@ -49,17 +44,6 @@
#define OMAP16XX_DSPREG_SIZE SZ_128K
#define OMAP16XX_DSPREG_START 0xE1000000
/*
* ----------------------------------------------------------------------------
* Memory used by power management
* ----------------------------------------------------------------------------
*/
#define OMAP1610_SRAM_IDLE_SUSPEND (OMAP16XX_SRAM_BASE + OMAP1610_SRAM_SIZE - 0x200)
#define OMAP1610_SRAM_API_SUSPEND (OMAP1610_SRAM_IDLE_SUSPEND + 0x100)
#define OMAP5912_SRAM_IDLE_SUSPEND (OMAP16XX_SRAM_BASE + OMAP5912_SRAM_SIZE - 0x200)
#define OMAP5912_SRAM_API_SUSPEND (OMAP5912_SRAM_IDLE_SUSPEND + 0x100)
/*
* ---------------------------------------------------------------------------
* Interrupts
......
#ifndef __ASM_ARCH_OMAP24XX_H
#define __ASM_ARCH_OMAP24XX_H
#define OMAP24XX_L4_IO_BASE 0x48000000
/* interrupt controller */
#define OMAP24XX_IC_BASE (OMAP24XX_L4_IO_BASE + 0xfe000)
#define VA_IC_BASE IO_ADDRESS(OMAP24XX_IC_BASE)
#define OMAP24XX_IVA_INTC_BASE 0x40000000
#define IRQ_SIR_IRQ 0x0040
#endif /* __ASM_ARCH_OMAP24XX_H */
......@@ -36,10 +36,6 @@
/* Syntax: XX_BASE = Virtual base address, XX_START = Physical base address */
#define OMAP730_SRAM_BASE 0xD0000000
#define OMAP730_SRAM_SIZE (SZ_128K + SZ_64K + SZ_8K)
#define OMAP730_SRAM_START 0x20000000
#define OMAP730_DSP_BASE 0xE0000000
#define OMAP730_DSP_SIZE 0x50000
#define OMAP730_DSP_START 0xE0000000
......
......@@ -61,7 +61,10 @@
#define PER_EN 0x1
#define CPU_SUSPEND_SIZE 200
#define ULPD_LOW_POWER_EN 0x0001
#define ULPD_LOW_PWR_EN 0x0001
#define ULPD_DEEP_SLEEP_TRANSITION_EN 0x0010
#define ULPD_SETUP_ANALOG_CELL_3_VAL 0
#define ULPD_POWER_CTRL_REG_VAL 0x0219
#define DSP_IDLE_DELAY 10
#define DSP_IDLE 0x0040
......@@ -86,46 +89,35 @@
#define OMAP1510_BIG_SLEEP_REQUEST 0x0cc5
#define OMAP1510_IDLE_LOOP_REQUEST 0x0c00
#define OMAP1510_IDLE_CLOCK_DOMAINS 0x2
#define OMAP1510_ULPD_LOW_POWER_REQ 0x0001
#define OMAP1610_DEEP_SLEEP_REQUEST 0x17c7
#define OMAP1610_BIG_SLEEP_REQUEST TBD
/* Both big sleep and deep sleep use same values. Difference is in ULPD. */
#define OMAP1610_IDLECT1_SLEEP_VAL 0x13c7
#define OMAP1610_IDLECT2_SLEEP_VAL 0x09c7
#define OMAP1610_IDLECT3_VAL 0x3f
#define OMAP1610_IDLECT3_SLEEP_ORMASK 0x2c
#define OMAP1610_IDLECT3 0xfffece24
#define OMAP1610_IDLE_LOOP_REQUEST 0x0400
#define OMAP1610_IDLE_CLOCK_DOMAINS 0x09c7
#define OMAP1610_ULPD_LOW_POWER_REQ 0x3
#ifndef OMAP1510_SRAM_IDLE_SUSPEND
#define OMAP1510_SRAM_IDLE_SUSPEND 0
#endif
#ifndef OMAP1610_SRAM_IDLE_SUSPEND
#define OMAP1610_SRAM_IDLE_SUSPEND 0
#endif
#ifndef OMAP5912_SRAM_IDLE_SUSPEND
#define OMAP5912_SRAM_IDLE_SUSPEND 0
#endif
#ifndef OMAP1510_SRAM_API_SUSPEND
#define OMAP1510_SRAM_API_SUSPEND 0
#endif
#ifndef OMAP1610_SRAM_API_SUSPEND
#define OMAP1610_SRAM_API_SUSPEND 0
#endif
#ifndef OMAP5912_SRAM_API_SUSPEND
#define OMAP5912_SRAM_API_SUSPEND 0
#endif
#if !defined(CONFIG_ARCH_OMAP1510) && \
!defined(CONFIG_ARCH_OMAP16XX)
!defined(CONFIG_ARCH_OMAP16XX) && \
!defined(CONFIG_ARCH_OMAP24XX)
#error "Power management for this processor not implemented yet"
#endif
#ifndef __ASSEMBLER__
extern void omap_pm_idle(void);
extern void omap_pm_suspend(void);
extern int omap1510_cpu_suspend(unsigned short, unsigned short);
extern int omap1610_cpu_suspend(unsigned short, unsigned short);
extern int omap1510_idle_loop_suspend(void);
extern int omap1610_idle_loop_suspend(void);
extern void omap1510_cpu_suspend(unsigned short, unsigned short);
extern void omap1610_cpu_suspend(unsigned short, unsigned short);
extern void omap1510_idle_loop_suspend(void);
extern void omap1610_idle_loop_suspend(void);
#ifdef CONFIG_OMAP_SERIAL_WAKE
extern void omap_serial_wake_trigger(int enable);
#else
#define omap_serial_wake_trigger(x) {}
#endif /* CONFIG_OMAP_SERIAL_WAKE */
extern unsigned int omap1510_cpu_suspend_sz;
extern unsigned int omap1510_idle_loop_suspend_sz;
extern unsigned int omap1610_cpu_suspend_sz;
......@@ -161,6 +153,7 @@ enum arm_save_state {
ARM_SLEEP_SAVE_ARM_CKCTL,
ARM_SLEEP_SAVE_ARM_IDLECT1,
ARM_SLEEP_SAVE_ARM_IDLECT2,
ARM_SLEEP_SAVE_ARM_IDLECT3,
ARM_SLEEP_SAVE_ARM_EWUPCT,
ARM_SLEEP_SAVE_ARM_RSTCT1,
ARM_SLEEP_SAVE_ARM_RSTCT2,
......
/*
* linux/include/asm-arm/arch-omap/serial.h
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#ifndef __ASM_ARCH_SERIAL_H
#define __ASM_ARCH_SERIAL_H
#if defined(CONFIG_ARCH_OMAP1)
/* OMAP1 serial ports */
#define OMAP_UART1_BASE 0xfffb0000
#define OMAP_UART2_BASE 0xfffb0800
#define OMAP_UART3_BASE 0xfffb9800
#elif defined(CONFIG_ARCH_OMAP2)
/* OMAP2 serial ports */
#define OMAP_UART1_BASE 0x4806a000
#define OMAP_UART2_BASE 0x4806c000
#define OMAP_UART3_BASE 0x4806e000
#endif
#define OMAP_MAX_NR_PORTS 3
#define OMAP1510_BASE_BAUD (12000000/16)
#define OMAP16XX_BASE_BAUD (48000000/16)
#define is_omap_port(p) ({int __ret = 0; \
if (p == IO_ADDRESS(OMAP_UART1_BASE) || \
p == IO_ADDRESS(OMAP_UART2_BASE) || \
p == IO_ADDRESS(OMAP_UART3_BASE)) \
__ret = 1; \
__ret; \
})
#endif
......@@ -20,7 +20,7 @@
#include <linux/config.h>
#include <linux/types.h>
#include <linux/serial_reg.h>
#include <asm/arch/hardware.h>
#include <asm/arch/serial.h>
unsigned int system_rev;
......@@ -34,8 +34,9 @@ static void
putstr(const char *s)
{
volatile u8 * uart = 0;
int shift;
int shift = 2;
#ifdef CONFIG_ARCH_OMAP
#ifdef CONFIG_OMAP_LL_DEBUG_UART3
uart = (volatile u8 *)(OMAP_UART3_BASE);
#elif CONFIG_OMAP_LL_DEBUG_UART2
......@@ -44,6 +45,7 @@ putstr(const char *s)
uart = (volatile u8 *)(OMAP_UART1_BASE);
#endif
#ifdef CONFIG_ARCH_OMAP1
/* Determine which serial port to use */
do {
/* MMU is not on, so cpu_is_omapXXXX() won't work here */
......@@ -51,14 +53,14 @@ putstr(const char *s)
if (omap_id == OMAP_ID_730)
shift = 0;
else
shift = 2;
if (check_port(uart, shift))
break;
/* Silent boot if no serial ports are enabled. */
return;
} while (0);
#endif /* CONFIG_ARCH_OMAP1 */
#endif
/*
* Now, xmit each character
......
/* linux/include/asm-arm/arch-s3c2410/anubis-cpld.h
*
* (c) 2005 Simtec Electronics
* http://www.simtec.co.uk/products/
* Ben Dooks <ben@simtec.co.uk>
*
* ANUBIS - CPLD control constants
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* Changelog:
*
*/
#ifndef __ASM_ARCH_ANUBISCPLD_H
#define __ASM_ARCH_ANUBISCPLD_H
/* CTRL2 - NAND WP control, IDE Reset assert/check */
#define ANUBIS_CTRL1_NANDSEL (0x3)
#endif /* __ASM_ARCH_ANUBISCPLD_H */
/* linux/include/asm-arm/arch-s3c2410/anubis-irq.h
*
* (c) 2005 Simtec Electronics
* http://www.simtec.co.uk/products/
* Ben Dooks <ben@simtec.co.uk>
*
* ANUBIS - IRQ Number definitions
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* Changelog:
*/
#ifndef __ASM_ARCH_ANUBISIRQ_H
#define __ASM_ARCH_ANUBISIRQ_H
#define IRQ_IDE0 IRQ_EINT2
#define IRQ_IDE1 IRQ_EINT3
#define IRQ_ASIX IRQ_EINT1
#endif /* __ASM_ARCH_ANUBISIRQ_H */
/* linux/include/asm-arm/arch-s3c2410/anubis-map.h
*
* (c) 2005 Simtec Electronics
* http://www.simtec.co.uk/products/
* Ben Dooks <ben@simtec.co.uk>
*
* ANUBIS - Memory map definitions
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* Changelog:
*/
/* needs arch/map.h including with this */
#ifndef __ASM_ARCH_ANUBISMAP_H
#define __ASM_ARCH_ANUBISMAP_H
/* start peripherals off after the S3C2410 */
#define ANUBIS_IOADDR(x) (S3C2410_ADDR((x) + 0x02000000))
#define ANUBIS_PA_CPLD (S3C2410_CS1 | (1<<26))
/* we put the CPLD registers next, to get them out of the way */
#define ANUBIS_VA_CTRL1 ANUBIS_IOADDR(0x00000000) /* 0x01300000 */
#define ANUBIS_PA_CTRL1 (ANUBIS_PA_CPLD)
#define ANUBIS_VA_CTRL2 ANUBIS_IOADDR(0x00100000) /* 0x01400000 */
#define ANUBIS_PA_CTRL2 (ANUBIS_PA_CPLD)
#define ANUBIS_VA_CTRL3 ANUBIS_IOADDR(0x00200000) /* 0x01500000 */
#define ANUBIS_PA_CTRL3 (ANUBIS_PA_CPLD)
#define ANUBIS_VA_CTRL4 ANUBIS_IOADDR(0x00300000) /* 0x01600000 */
#define ANUBIS_PA_CTRL4 (ANUBIS_PA_CPLD)
#define ANUBIS_IDEPRI ANUBIS_IOADDR(0x01000000)
#define ANUBIS_IDEPRIAUX ANUBIS_IOADDR(0x01100000)
#define ANUBIS_IDESEC ANUBIS_IOADDR(0x01200000)
#define ANUBIS_IDESECAUX ANUBIS_IOADDR(0x01300000)
#endif /* __ASM_ARCH_ANUBISMAP_H */
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment