Commit 10c1d542 authored by Tim Harvey's avatar Tim Harvey Committed by Mauro Carvalho Chehab

media: dt-bindings: Add bindings for TDA1997X

Define the device tree bindings for the TDA1997X.
Acked-by: default avatarRob Herring <robh@kernel.org>
Acked-by: default avatarSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: default avatarTim Harvey <tharvey@gateworks.com>
Signed-off-by: default avatarHans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: make a proper commit message]
Signed-off-by: default avatarMauro Carvalho Chehab <mchehab@s-opensource.com>
parent 4cd9659e
Device-Tree bindings for the NXP TDA1997x HDMI receiver
The TDA19971/73 are HDMI video receivers.
The TDA19971 Video port output pins can be used as follows:
- RGB 8bit per color (24 bits total): R[11:4] B[11:4] G[11:4]
- YUV444 8bit per color (24 bits total): Y[11:4] Cr[11:4] Cb[11:4]
- YUV422 semi-planar 8bit per component (16 bits total): Y[11:4] CbCr[11:4]
- YUV422 semi-planar 10bit per component (20 bits total): Y[11:2] CbCr[11:2]
- YUV422 semi-planar 12bit per component (24 bits total): - Y[11:0] CbCr[11:0]
- YUV422 BT656 8bit per component (8 bits total): YCbCr[11:4] (2-cycles)
- YUV422 BT656 10bit per component (10 bits total): YCbCr[11:2] (2-cycles)
- YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles)
The TDA19973 Video port output pins can be used as follows:
- RGB 12bit per color (36 bits total): R[11:0] B[11:0] G[11:0]
- YUV444 12bit per color (36 bits total): Y[11:0] Cb[11:0] Cr[11:0]
- YUV422 semi-planar 12bit per component (24 bits total): Y[11:0] CbCr[11:0]
- YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles)
The Video port output pins are mapped via 4-bit 'pin groups' allowing
for a variety of connection possibilities including swapping pin order within
pin groups. The video_portcfg device-tree property consists of register mapping
pairs which map a chip-specific VP output register to a 4-bit pin group. If
the pin group needs to be bit-swapped you can use the *_S pin-group defines.
Required Properties:
- compatible :
- "nxp,tda19971" for the TDA19971
- "nxp,tda19973" for the TDA19973
- reg : I2C slave address
- interrupts : The interrupt number
- DOVDD-supply : Digital I/O supply
- DVDD-supply : Digital Core supply
- AVDD-supply : Analog supply
- nxp,vidout-portcfg : array of pairs mapping VP output pins to pin groups.
Optional Properties:
- nxp,audout-format : DAI bus format: "i2s" or "spdif".
- nxp,audout-width : width of audio output data bus (1-4).
- nxp,audout-layout : data layout (0=AP0 used, 1=AP0/AP1/AP2/AP3 used).
- nxp,audout-mclk-fs : Multiplication factor between stream rate and codec
mclk.
The port node shall contain one endpoint child node for its digital
output video port, in accordance with the video interface bindings defined in
Documentation/devicetree/bindings/media/video-interfaces.txt.
Optional Endpoint Properties:
The following three properties are defined in video-interfaces.txt and
are valid for the output parallel bus endpoint:
- hsync-active: Horizontal synchronization polarity. Defaults to active high.
- vsync-active: Vertical synchronization polarity. Defaults to active high.
- data-active: Data polarity. Defaults to active high.
Examples:
- VP[15:0] connected to IMX6 CSI_DATA[19:4] for 16bit YUV422
16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins)
hdmi-receiver@48 {
compatible = "nxp,tda19971";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_tda1997x>;
reg = <0x48>;
interrupt-parent = <&gpio1>;
interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
DOVDD-supply = <&reg_3p3v>;
AVDD-supply = <&reg_1p8v>;
DVDD-supply = <&reg_1p8v>;
/* audio */
#sound-dai-cells = <0>;
nxp,audout-format = "i2s";
nxp,audout-layout = <0>;
nxp,audout-width = <16>;
nxp,audout-mclk-fs = <128>;
/*
* The 8bpp YUV422 semi-planar mode outputs CbCr[11:4]
* and Y[11:4] across 16bits in the same pixclk cycle.
*/
nxp,vidout-portcfg =
/* Y[11:8]<->VP[15:12]<->CSI_DATA[19:16] */
< TDA1997X_VP24_V15_12 TDA1997X_G_Y_11_8 >,
/* Y[7:4]<->VP[11:08]<->CSI_DATA[15:12] */
< TDA1997X_VP24_V11_08 TDA1997X_G_Y_7_4 >,
/* CbCc[11:8]<->VP[07:04]<->CSI_DATA[11:8] */
< TDA1997X_VP24_V07_04 TDA1997X_R_CR_CBCR_11_8 >,
/* CbCr[7:4]<->VP[03:00]<->CSI_DATA[7:4] */
< TDA1997X_VP24_V03_00 TDA1997X_R_CR_CBCR_7_4 >;
port {
tda1997x_to_ipu1_csi0_mux: endpoint {
remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
bus-width = <16>;
hsync-active = <1>;
vsync-active = <1>;
data-active = <1>;
};
};
};
- VP[15:8] connected to IMX6 CSI_DATA[19:12] for 8bit BT656
16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins)
hdmi-receiver@48 {
compatible = "nxp,tda19971";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_tda1997x>;
reg = <0x48>;
interrupt-parent = <&gpio1>;
interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
DOVDD-supply = <&reg_3p3v>;
AVDD-supply = <&reg_1p8v>;
DVDD-supply = <&reg_1p8v>;
/* audio */
#sound-dai-cells = <0>;
nxp,audout-format = "i2s";
nxp,audout-layout = <0>;
nxp,audout-width = <16>;
nxp,audout-mclk-fs = <128>;
/*
* The 8bpp YUV422 semi-planar mode outputs CbCr[11:4]
* and Y[11:4] across 16bits in the same pixclk cycle.
*/
nxp,vidout-portcfg =
/* Y[11:8]<->VP[15:12]<->CSI_DATA[19:16] */
< TDA1997X_VP24_V15_12 TDA1997X_G_Y_11_8 >,
/* Y[7:4]<->VP[11:08]<->CSI_DATA[15:12] */
< TDA1997X_VP24_V11_08 TDA1997X_G_Y_7_4 >,
/* CbCc[11:8]<->VP[07:04]<->CSI_DATA[11:8] */
< TDA1997X_VP24_V07_04 TDA1997X_R_CR_CBCR_11_8 >,
/* CbCr[7:4]<->VP[03:00]<->CSI_DATA[7:4] */
< TDA1997X_VP24_V03_00 TDA1997X_R_CR_CBCR_7_4 >;
port {
tda1997x_to_ipu1_csi0_mux: endpoint {
remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
bus-width = <16>;
hsync-active = <1>;
vsync-active = <1>;
data-active = <1>;
};
};
};
- VP[15:8] connected to IMX6 CSI_DATA[19:12] for 8bit BT656
16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins)
hdmi-receiver@48 {
compatible = "nxp,tda19971";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_tda1997x>;
reg = <0x48>;
interrupt-parent = <&gpio1>;
interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
DOVDD-supply = <&reg_3p3v>;
AVDD-supply = <&reg_1p8v>;
DVDD-supply = <&reg_1p8v>;
/* audio */
#sound-dai-cells = <0>;
nxp,audout-format = "i2s";
nxp,audout-layout = <0>;
nxp,audout-width = <16>;
nxp,audout-mclk-fs = <128>;
/*
* The 8bpp BT656 mode outputs YCbCr[11:4] across 8bits over
* 2 pixclk cycles.
*/
nxp,vidout-portcfg =
/* YCbCr[11:8]<->VP[15:12]<->CSI_DATA[19:16] */
< TDA1997X_VP24_V15_12 TDA1997X_R_CR_CBCR_11_8 >,
/* YCbCr[7:4]<->VP[11:08]<->CSI_DATA[15:12] */
< TDA1997X_VP24_V11_08 TDA1997X_R_CR_CBCR_7_4 >,
port {
tda1997x_to_ipu1_csi0_mux: endpoint {
remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
bus-width = <16>;
hsync-active = <1>;
vsync-active = <1>;
data-active = <1>;
};
};
};
/* SPDX-License-Identifier: GPL-2.0 */
/*
* Copyright (C) 2017 Gateworks Corporation
*/
#ifndef _DT_BINDINGS_MEDIA_TDA1997X_H
#define _DT_BINDINGS_MEDIA_TDA1997X_H
/* TDA19973 36bit Video Port control registers */
#define TDA1997X_VP36_35_32 0
#define TDA1997X_VP36_31_28 1
#define TDA1997X_VP36_27_24 2
#define TDA1997X_VP36_23_20 3
#define TDA1997X_VP36_19_16 4
#define TDA1997X_VP36_15_12 5
#define TDA1997X_VP36_11_08 6
#define TDA1997X_VP36_07_04 7
#define TDA1997X_VP36_03_00 8
/* TDA19971 24bit Video Port control registers */
#define TDA1997X_VP24_V23_20 0
#define TDA1997X_VP24_V19_16 1
#define TDA1997X_VP24_V15_12 3
#define TDA1997X_VP24_V11_08 4
#define TDA1997X_VP24_V07_04 6
#define TDA1997X_VP24_V03_00 7
/* Pin groups */
#define TDA1997X_VP_OUT_EN 0x80 /* enable output group */
#define TDA1997X_VP_HIZ 0x40 /* hi-Z output group when not used */
#define TDA1997X_VP_SWP 0x10 /* pin-swap output group */
#define TDA1997X_R_CR_CBCR_3_0 (0 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ)
#define TDA1997X_R_CR_CBCR_7_4 (1 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ)
#define TDA1997X_R_CR_CBCR_11_8 (2 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ)
#define TDA1997X_B_CB_3_0 (3 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ)
#define TDA1997X_B_CB_7_4 (4 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ)
#define TDA1997X_B_CB_11_8 (5 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ)
#define TDA1997X_G_Y_3_0 (6 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ)
#define TDA1997X_G_Y_7_4 (7 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ)
#define TDA1997X_G_Y_11_8 (8 | TDA1997X_VP_OUT_EN | TDA1997X_VP_HIZ)
/* pinswapped groups */
#define TDA1997X_R_CR_CBCR_3_0_S (TDA1997X_R_CR_CBCR_3_0 | TDA1997X_VP_SWAP)
#define TDA1997X_R_CR_CBCR_7_4_S (TDA1997X_R_CR_CBCR_7_4 | TDA1997X_VP_SWAP)
#define TDA1997X_R_CR_CBCR_11_8_S (TDA1997X_R_CR_CBCR_11_8 | TDA1997X_VP_SWAP)
#define TDA1997X_B_CB_3_0_S (TDA1997X_B_CB_3_0 | TDA1997X_VP_SWAP)
#define TDA1997X_B_CB_7_4_S (TDA1997X_B_CB_7_4 | TDA1997X_VP_SWAP)
#define TDA1997X_B_CB_11_8_S (TDA1997X_B_CB_11_8 | TDA1997X_VP_SWAP)
#define TDA1997X_G_Y_3_0_S (TDA1997X_G_Y_3_0 | TDA1997X_VP_SWAP)
#define TDA1997X_G_Y_7_4_S (TDA1997X_G_Y_7_4 | TDA1997X_VP_SWAP)
#define TDA1997X_G_Y_11_8_S (TDA1997X_G_Y_11_8 | TDA1997X_VP_SWAP)
/* Audio bus DAI format */
#define TDA1997X_I2S16 1 /* I2S 16bit */
#define TDA1997X_I2S32 2 /* I2S 32bit */
#define TDA1997X_SPDIF 3 /* SPDIF */
#define TDA1997X_OBA 4 /* One Bit Audio */
#define TDA1997X_DST 5 /* Direct Stream Transfer */
#define TDA1997X_I2S16_HBR 6 /* HBR straight in I2S 16bit mode */
#define TDA1997X_I2S16_HBR_DEMUX 7 /* HBR demux in I2S 16bit mode */
#define TDA1997X_I2S32_HBR_DEMUX 8 /* HBR demux in I2S 32bit mode */
#define TDA1997X_SPDIF_HBR_DEMUX 9 /* HBR demux in SPDIF mode */
/* Audio bus channel layout */
#define TDA1997X_LAYOUT0 0 /* 2-channel */
#define TDA1997X_LAYOUT1 1 /* 8-channel */
/* Audio bus clock */
#define TDA1997X_ACLK_16FS 0
#define TDA1997X_ACLK_32FS 1
#define TDA1997X_ACLK_64FS 2
#define TDA1997X_ACLK_128FS 3
#define TDA1997X_ACLK_256FS 4
#define TDA1997X_ACLK_512FS 5
#endif /* _DT_BINDINGS_MEDIA_TDA1997X_H */
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment