Commit 11e5015a authored by Laurent Pinchart's avatar Laurent Pinchart Committed by Greg Kroah-Hartman

v4l: tvp5150: Fix comment regarding output pin muxing

commit b4b2de38 upstream.

The FID/GLCO/VLK/HVLK and INTREQ/GPCL/VBLK pins are muxed differently
depending on whether the input is an S-Video or composite signal. The
comment that explains the logic doesn't reflect the code. It appears
that the comment is incorrect, as disabling the output data bus in
composite mode makes no sense. Update the comment to match the code.

While at it define macros for the MISC_CTL register bits, the code is
too confusing with numerical values.
Signed-off-by: default avatarLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: default avatarMauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
parent d25f9bfe
......@@ -288,8 +288,12 @@ static inline void tvp5150_selmux(struct v4l2_subdev *sd)
tvp5150_write(sd, TVP5150_OP_MODE_CTL, opmode);
tvp5150_write(sd, TVP5150_VD_IN_SRC_SEL_1, input);
/* Svideo should enable YCrCb output and disable GPCL output
* For Composite and TV, it should be the reverse
/*
* Setup the FID/GLCO/VLK/HVLK and INTREQ/GPCL/VBLK output signals. For
* S-Video we output the vertical lock (VLK) signal on FID/GLCO/VLK/HVLK
* and set INTREQ/GPCL/VBLK to logic 0. For composite we output the
* field indicator (FID) signal on FID/GLCO/VLK/HVLK and set
* INTREQ/GPCL/VBLK to logic 1.
*/
val = tvp5150_read(sd, TVP5150_MISC_CTL);
if (val < 0) {
......@@ -298,9 +302,9 @@ static inline void tvp5150_selmux(struct v4l2_subdev *sd)
}
if (decoder->input == TVP5150_SVIDEO)
val = (val & ~0x40) | 0x10;
val = (val & ~TVP5150_MISC_CTL_GPCL) | TVP5150_MISC_CTL_HVLK;
else
val = (val & ~0x10) | 0x40;
val = (val & ~TVP5150_MISC_CTL_HVLK) | TVP5150_MISC_CTL_GPCL;
tvp5150_write(sd, TVP5150_MISC_CTL, val);
};
......@@ -452,7 +456,12 @@ static const struct i2c_reg_value tvp5150_init_enable[] = {
},{ /* Automatic offset and AGC enabled */
TVP5150_ANAL_CHL_CTL, 0x15
},{ /* Activate YCrCb output 0x9 or 0xd ? */
TVP5150_MISC_CTL, 0x6f
TVP5150_MISC_CTL, TVP5150_MISC_CTL_GPCL |
TVP5150_MISC_CTL_INTREQ_OE |
TVP5150_MISC_CTL_YCBCR_OE |
TVP5150_MISC_CTL_SYNC_OE |
TVP5150_MISC_CTL_VBLANK |
TVP5150_MISC_CTL_CLOCK_OE,
},{ /* Activates video std autodetection for all standards */
TVP5150_AUTOSW_MSK, 0x0
},{ /* Default format: 0x47. For 4:2:2: 0x40 */
......@@ -1047,11 +1056,12 @@ static int tvp5150_s_stream(struct v4l2_subdev *sd, int enable)
{
struct tvp5150 *decoder = to_tvp5150(sd);
/* Output format: 8-bit ITU-R BT.656 with embedded syncs */
int val = 0x09;
int val = TVP5150_MISC_CTL_YCBCR_OE | TVP5150_MISC_CTL_CLOCK_OE;
/* Output format: 8-bit 4:2:2 YUV with discrete sync */
if (decoder->mbus_type == V4L2_MBUS_PARALLEL)
val = 0x0d;
val = TVP5150_MISC_CTL_YCBCR_OE | TVP5150_MISC_CTL_SYNC_OE
| TVP5150_MISC_CTL_CLOCK_OE;
/* Initializes TVP5150 to its default values */
/* # set PCLK (27MHz) */
......
......@@ -9,6 +9,15 @@
#define TVP5150_ANAL_CHL_CTL 0x01 /* Analog channel controls */
#define TVP5150_OP_MODE_CTL 0x02 /* Operation mode controls */
#define TVP5150_MISC_CTL 0x03 /* Miscellaneous controls */
#define TVP5150_MISC_CTL_VBLK_GPCL BIT(7)
#define TVP5150_MISC_CTL_GPCL BIT(6)
#define TVP5150_MISC_CTL_INTREQ_OE BIT(5)
#define TVP5150_MISC_CTL_HVLK BIT(4)
#define TVP5150_MISC_CTL_YCBCR_OE BIT(3)
#define TVP5150_MISC_CTL_SYNC_OE BIT(2)
#define TVP5150_MISC_CTL_VBLANK BIT(1)
#define TVP5150_MISC_CTL_CLOCK_OE BIT(0)
#define TVP5150_AUTOSW_MSK 0x04 /* Autoswitch mask: TVP5150A / TVP5150AM */
/* Reserved 05h */
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment