Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon updates from Guenter Roeck:
 "New driver for INA219 and INA226, added support for IT8782F and
  IT8783E/F to it87 driver, plus cleanups in a couple of drivers."

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (it87) Make temp3 attribute conditional for IT8782F
  hwmon: (it87) Convert to use devm_kzalloc and devm_request_region
  hwmon: INA219 and INA226 support
  hwmon: (it87) Create voltage attributes only if voltage is enabled
  hwmon: (ntc_thermistor) Fix checkpatch warning
  hwmon: (ntc_thermistor) Optimize and fix build warning
  hwmon: (ntc_thermistor) Return error code from hwmon_device_register
  hwmon: (ntc_thermistor) Convert to devm_kzalloc
  hwmon: (ad7314) Remove unused defines, and rename OFFSET to SHIFT
  acpi_power_meter: clean up code around setup_attrs
  acpi_power_meter: drop meter_rw_attrs, use common meter_attrs
  acpi_power_meter: remove duplicate code between register_{ro,rw}_attrs
  acpi_power_meter: use a {RW,RO}_SENSOR_TEMPLATE macro to clean things up
  acpi_power_meter: use the same struct {rw,ro}_sensor_template for both
  hwmon: use module_pci_driver
  hwmon: (it87) Add support for IT8782F and IT8783E/F

Documentation/hwmon/ina2xx

+Kernel driver ina2xx
+====================
+
+Supported chips:
+  * Texas Instruments INA219
+    Prefix: 'ina219'
+    Addresses: I2C 0x40 - 0x4f
+    Datasheet: Publicly available at the Texas Instruments website
+               http://www.ti.com/
+
+  * Texas Instruments INA226
+    Prefix: 'ina226'
+    Addresses: I2C 0x40 - 0x4f
+    Datasheet: Publicly available at the Texas Instruments website
+               http://www.ti.com/
+
+Author: Lothar Felten <l-felten@ti.com>
+
+Description
+-----------
+
+The INA219 is a high-side current shunt and power monitor with an I2C
+interface. The INA219 monitors both shunt drop and supply voltage, with
+programmable conversion times and filtering.
+
+The INA226 is a current shunt and power monitor with an I2C interface.
+The INA226 monitors both a shunt voltage drop and bus supply voltage.
+
+The shunt value in micro-ohms can be set via platform data.

Documentation/hwmon/it87

@@ -30,6 +30,14 @@ Supported chips:
     Prefix: 'it8728'
     Addresses scanned: from Super I/O config space (8 I/O ports)
     Datasheet: Not publicly available
+  * IT8782F
+    Prefix: 'it8782'
+    Addresses scanned: from Super I/O config space (8 I/O ports)
+    Datasheet: Not publicly available
+  * IT8783E/F
+    Prefix: 'it8783'
+    Addresses scanned: from Super I/O config space (8 I/O ports)
+    Datasheet: Not publicly available
   * SiS950   [clone of IT8705F]
     Prefix: 'it87'
     Addresses scanned: from Super I/O config space (8 I/O ports)
@@ -75,7 +83,8 @@ Description
 -----------
 
 This driver implements support for the IT8705F, IT8712F, IT8716F,
-IT8718F, IT8720F, IT8721F, IT8726F, IT8728F, IT8758E and SiS950 chips.
+IT8718F, IT8720F, IT8721F, IT8726F, IT8728F, IT8758E, IT8781F, IT8782F,
+IT8783E/F, and SiS950 chips.
 
 These chips are 'Super I/O chips', supporting floppy disks, infrared ports,
 joysticks and other miscellaneous stuff. For hardware monitoring, they
@@ -99,11 +108,11 @@ The IT8716F, IT8718F, IT8720F, IT8721F/IT8758E and later IT8712F revisions
 have support for 2 additional fans. The additional fans are supported by the
 driver.
 
-The IT8716F, IT8718F, IT8720F and IT8721F/IT8758E, and late IT8712F and
-IT8705F also have optional 16-bit tachometer counters for fans 1 to 3. This
-is better (no more fan clock divider mess) but not compatible with the older
-chips and revisions. The 16-bit tachometer mode is enabled by the driver when
-one of the above chips is detected.
+The IT8716F, IT8718F, IT8720F, IT8721F/IT8758E, IT8782F, IT8783E/F, and late
+IT8712F and IT8705F also have optional 16-bit tachometer counters for fans 1 to
+3. This is better (no more fan clock divider mess) but not compatible with the
+older chips and revisions. The 16-bit tachometer mode is enabled by the driver
+when one of the above chips is detected.
 
 The IT8726F is just bit enhanced IT8716F with additional hardware
 for AMD power sequencing. Therefore the chip will appear as IT8716F
@@ -131,9 +140,10 @@ inputs can measure voltages between 0 and 4.08 volts, with a resolution of
 0.016 volt (except IT8721F/IT8758E and IT8728F: 0.012 volt.) The battery
 voltage in8 does not have limit registers.
 
-On the IT8721F/IT8758E, some voltage inputs are internal and scaled inside
-the chip (in7, in8 and optionally in3). The driver handles this transparently
-so user-space doesn't have to care.
+On the IT8721F/IT8758E, IT8782F, and IT8783E/F, some voltage inputs are
+internal and scaled inside the chip (in7 (optional for IT8782F and IT8783E/F),
+in8 and optionally in3). The driver handles this transparently so user-space
+doesn't have to care.
 
 The VID lines (IT8712F/IT8716F/IT8718F/IT8720F) encode the core voltage value:
 the voltage level your processor should work with. This is hardcoded by

drivers/hwmon/Kconfig

@@ -1102,6 +1102,19 @@ config SENSORS_AMC6821
 	  This driver can also be build as a module.  If so, the module
 	  will be called amc6821.
 
+config SENSORS_INA2XX
+	tristate "Texas Instruments INA219, INA226"
+	depends on I2C && EXPERIMENTAL
+	help
+	  If you say yes here you get support for INA219 and INA226 power
+	  monitor chips.
+
+	  The INA2xx driver is configured for the default configuration of
+	  the part as described in the datasheet.
+	  Default value for Rshunt is 10 mOhms.
+	  This driver can also be built as a module.  If so, the module
+	  will be called ina2xx.
+
 config SENSORS_THMC50
 	tristate "Texas Instruments THMC50 / Analog Devices ADM1022"
 	depends on I2C

drivers/hwmon/Makefile

@@ -62,6 +62,7 @@ obj-$(CONFIG_SENSORS_ULTRA45)	+= ultra45_env.o
 obj-$(CONFIG_SENSORS_I5K_AMB)	+= i5k_amb.o
 obj-$(CONFIG_SENSORS_IBMAEM)	+= ibmaem.o
 obj-$(CONFIG_SENSORS_IBMPEX)	+= ibmpex.o
+obj-$(CONFIG_SENSORS_INA2XX)	+= ina2xx.o
 obj-$(CONFIG_SENSORS_IT87)	+= it87.o
 obj-$(CONFIG_SENSORS_JC42)	+= jc42.o
 obj-$(CONFIG_SENSORS_JZ4740)	+= jz4740-hwmon.o

drivers/hwmon/acpi_power_meter.c

@@ -107,15 +107,7 @@ struct acpi_power_meter_resource {
 	struct kobject		*holders_dir;
 };
 
-struct ro_sensor_template {
-	char *label;
-	ssize_t (*show)(struct device *dev,
-			struct device_attribute *devattr,
-			char *buf);
-	int index;
-};
-
-struct rw_sensor_template {
+struct sensor_template {
 	char *label;
 	ssize_t (*show)(struct device *dev,
 			struct device_attribute *devattr,
@@ -469,52 +461,67 @@ static ssize_t show_name(struct device *dev,
 	return sprintf(buf, "%s\n", ACPI_POWER_METER_NAME);
 }
 
+#define RO_SENSOR_TEMPLATE(_label, _show, _index)	\
+	{						\
+		.label = _label,			\
+		.show  = _show,				\
+		.index = _index,			\
+	}
+
+#define RW_SENSOR_TEMPLATE(_label, _show, _set, _index)	\
+	{						\
+		.label = _label,			\
+		.show  = _show,				\
+		.set   = _set,				\
+		.index = _index,			\
+	}
+
 /* Sensor descriptions.  If you add a sensor, update NUM_SENSORS above! */
-static struct ro_sensor_template meter_ro_attrs[] = {
-{POWER_AVERAGE_NAME, show_power, 0},
-{"power1_accuracy", show_accuracy, 0},
-{"power1_average_interval_min", show_val, 0},
-{"power1_average_interval_max", show_val, 1},
-{"power1_is_battery", show_val, 5},
-{NULL, NULL, 0},
+static struct sensor_template meter_attrs[] = {
+	RO_SENSOR_TEMPLATE(POWER_AVERAGE_NAME, show_power, 0),
+	RO_SENSOR_TEMPLATE("power1_accuracy", show_accuracy, 0),
+	RO_SENSOR_TEMPLATE("power1_average_interval_min", show_val, 0),
+	RO_SENSOR_TEMPLATE("power1_average_interval_max", show_val, 1),
+	RO_SENSOR_TEMPLATE("power1_is_battery", show_val, 5),
+	RW_SENSOR_TEMPLATE(POWER_AVG_INTERVAL_NAME, show_avg_interval,
+		set_avg_interval, 0),
+	{},
 };
 
-static struct rw_sensor_template meter_rw_attrs[] = {
-{POWER_AVG_INTERVAL_NAME, show_avg_interval, set_avg_interval, 0},
-{NULL, NULL, NULL, 0},
+static struct sensor_template misc_cap_attrs[] = {
+	RO_SENSOR_TEMPLATE("power1_cap_min", show_val, 2),
+	RO_SENSOR_TEMPLATE("power1_cap_max", show_val, 3),
+	RO_SENSOR_TEMPLATE("power1_cap_hyst", show_val, 4),
+	RO_SENSOR_TEMPLATE(POWER_ALARM_NAME, show_val, 6),
+	{},
 };
 
-static struct ro_sensor_template misc_cap_attrs[] = {
-{"power1_cap_min", show_val, 2},
-{"power1_cap_max", show_val, 3},
-{"power1_cap_hyst", show_val, 4},
-{POWER_ALARM_NAME, show_val, 6},
-{NULL, NULL, 0},
+static struct sensor_template ro_cap_attrs[] = {
+	RO_SENSOR_TEMPLATE(POWER_CAP_NAME, show_cap, 0),
+	{},
 };
 
-static struct ro_sensor_template ro_cap_attrs[] = {
-{POWER_CAP_NAME, show_cap, 0},
-{NULL, NULL, 0},
+static struct sensor_template rw_cap_attrs[] = {
+	RW_SENSOR_TEMPLATE(POWER_CAP_NAME, show_cap, set_cap, 0),
+	{},
 };
 
-static struct rw_sensor_template rw_cap_attrs[] = {
-{POWER_CAP_NAME, show_cap, set_cap, 0},
-{NULL, NULL, NULL, 0},
+static struct sensor_template trip_attrs[] = {
+	RW_SENSOR_TEMPLATE("power1_average_min", show_val, set_trip, 7),
+	RW_SENSOR_TEMPLATE("power1_average_max", show_val, set_trip, 8),
+	{},
 };
 
-static struct rw_sensor_template trip_attrs[] = {
-{"power1_average_min", show_val, set_trip, 7},
-{"power1_average_max", show_val, set_trip, 8},
-{NULL, NULL, NULL, 0},
+static struct sensor_template misc_attrs[] = {
+	RO_SENSOR_TEMPLATE("name", show_name, 0),
+	RO_SENSOR_TEMPLATE("power1_model_number", show_str, 0),
+	RO_SENSOR_TEMPLATE("power1_oem_info", show_str, 2),
+	RO_SENSOR_TEMPLATE("power1_serial_number", show_str, 1),
+	{},
 };
 
-static struct ro_sensor_template misc_attrs[] = {
-{"name", show_name, 0},
-{"power1_model_number", show_str, 0},
-{"power1_oem_info", show_str, 2},
-{"power1_serial_number", show_str, 1},
-{NULL, NULL, 0},
-};
+#undef RO_SENSOR_TEMPLATE
+#undef RW_SENSOR_TEMPLATE
 
 /* Read power domain data */
 static void remove_domain_devices(struct acpi_power_meter_resource *resource)
@@ -619,49 +626,24 @@ static int read_domain_devices(struct acpi_power_meter_resource *resource)
 }
 
 /* Registration and deregistration */
-static int register_ro_attrs(struct acpi_power_meter_resource *resource,
-			     struct ro_sensor_template *ro)
+static int register_attrs(struct acpi_power_meter_resource *resource,
+			  struct sensor_template *attrs)
 {
 	struct device *dev = &resource->acpi_dev->dev;
 	struct sensor_device_attribute *sensors =
 		&resource->sensors[resource->num_sensors];
 	int res = 0;
 
-	while (ro->label) {
-		sensors->dev_attr.attr.name = ro->label;
+	while (attrs->label) {
+		sensors->dev_attr.attr.name = attrs->label;
 		sensors->dev_attr.attr.mode = S_IRUGO;
-		sensors->dev_attr.show = ro->show;
-		sensors->index = ro->index;
+		sensors->dev_attr.show = attrs->show;
+		sensors->index = attrs->index;
 
-		sysfs_attr_init(&sensors->dev_attr.attr);
-		res = device_create_file(dev, &sensors->dev_attr);
-		if (res) {
-			sensors->dev_attr.attr.name = NULL;
-			goto error;
+		if (attrs->set) {
+			sensors->dev_attr.attr.mode |= S_IWUSR;
+			sensors->dev_attr.store = attrs->set;
 		}
-		sensors++;
-		resource->num_sensors++;
-		ro++;
-	}
-
-error:
-	return res;
-}
-
-static int register_rw_attrs(struct acpi_power_meter_resource *resource,
-			     struct rw_sensor_template *rw)
-{
-	struct device *dev = &resource->acpi_dev->dev;
-	struct sensor_device_attribute *sensors =
-		&resource->sensors[resource->num_sensors];
-	int res = 0;
-
-	while (rw->label) {
-		sensors->dev_attr.attr.name = rw->label;
-		sensors->dev_attr.attr.mode = S_IRUGO | S_IWUSR;
-		sensors->dev_attr.show = rw->show;
-		sensors->dev_attr.store = rw->set;
-		sensors->index = rw->index;
 
 		sysfs_attr_init(&sensors->dev_attr.attr);
 		res = device_create_file(dev, &sensors->dev_attr);
@@ -671,7 +653,7 @@ static int register_rw_attrs(struct acpi_power_meter_resource *resource,
 		}
 		sensors++;
 		resource->num_sensors++;
-		rw++;
+		attrs++;
 	}
 
 error:
@@ -703,10 +685,7 @@ static int setup_attrs(struct acpi_power_meter_resource *resource)
 		return res;
 
 	if (resource->caps.flags & POWER_METER_CAN_MEASURE) {
-		res = register_ro_attrs(resource, meter_ro_attrs);
-		if (res)
-			goto error;
-		res = register_rw_attrs(resource, meter_rw_attrs);
+		res = register_attrs(resource, meter_attrs);
 		if (res)
 			goto error;
 	}
@@ -718,28 +697,27 @@ static int setup_attrs(struct acpi_power_meter_resource *resource)
 			goto skip_unsafe_cap;
 		}
 
-		if (resource->caps.configurable_cap) {
-			res = register_rw_attrs(resource, rw_cap_attrs);
-			if (res)
-				goto error;
-		} else {
-			res = register_ro_attrs(resource, ro_cap_attrs);
-			if (res)
-				goto error;
-		}
-		res = register_ro_attrs(resource, misc_cap_attrs);
+		if (resource->caps.configurable_cap)
+			res = register_attrs(resource, rw_cap_attrs);
+		else
+			res = register_attrs(resource, ro_cap_attrs);
+
+		if (res)
+			goto error;
+
+		res = register_attrs(resource, misc_cap_attrs);
 		if (res)
 			goto error;
 	}
-skip_unsafe_cap:
 
+skip_unsafe_cap:
 	if (resource->caps.flags & POWER_METER_CAN_TRIP) {
-		res = register_rw_attrs(resource, trip_attrs);
+		res = register_attrs(resource, trip_attrs);
 		if (res)
 			goto error;
 	}
 
-	res = register_ro_attrs(resource, misc_attrs);
+	res = register_attrs(resource, misc_attrs);
 	if (res)
 		goto error;
 

drivers/hwmon/ad7314.c

@@ -17,22 +17,15 @@
 #include <linux/hwmon.h>
 #include <linux/hwmon-sysfs.h>
 
-/*
- * AD7314 power mode
- */
-#define AD7314_PD		0x2000
-
 /*
  * AD7314 temperature masks
  */
-#define AD7314_TEMP_SIGN		0x200
 #define AD7314_TEMP_MASK		0x7FE0
-#define AD7314_TEMP_OFFSET		5
+#define AD7314_TEMP_SHIFT		5
 
 /*
  * ADT7301 and ADT7302 temperature masks
  */
-#define ADT7301_TEMP_SIGN		0x2000
 #define ADT7301_TEMP_MASK		0x3FFF
 
 enum ad7314_variant {
@@ -73,7 +66,7 @@ static ssize_t ad7314_show_temperature(struct device *dev,
 		return ret;
 	switch (spi_get_device_id(chip->spi_dev)->driver_data) {
 	case ad7314:
-		data = (ret & AD7314_TEMP_MASK) >> AD7314_TEMP_OFFSET;
+		data = (ret & AD7314_TEMP_MASK) >> AD7314_TEMP_SHIFT;
 		data = (data << 6) >> 6;
 
 		return sprintf(buf, "%d\n", 250 * data);

drivers/hwmon/fam15h_power.c

@@ -257,15 +257,4 @@ static struct pci_driver fam15h_power_driver = {
 	.remove = __devexit_p(fam15h_power_remove),
 };
 
-static int __init fam15h_power_init(void)
-{
-	return pci_register_driver(&fam15h_power_driver);
-}
-
-static void __exit fam15h_power_exit(void)
-{
-	pci_unregister_driver(&fam15h_power_driver);
-}
-
-module_init(fam15h_power_init)
-module_exit(fam15h_power_exit)
+module_pci_driver(fam15h_power_driver);

drivers/hwmon/ina2xx.c

+/*
+ * Driver for Texas Instruments INA219, INA226 power monitor chips
+ *
+ * INA219:
+ * Zero Drift Bi-Directional Current/Power Monitor with I2C Interface
+ * Datasheet: http://www.ti.com/product/ina219
+ *
+ * INA226:
+ * Bi-Directional Current/Power Monitor with I2C Interface
+ * Datasheet: http://www.ti.com/product/ina226
+ *
+ * Copyright (C) 2012 Lothar Felten <l-felten@ti.com>
+ * Thanks to Jan Volkering
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/err.h>
+#include <linux/slab.h>
+#include <linux/i2c.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+
+#include <linux/platform_data/ina2xx.h>
+
+/* common register definitions */
+#define INA2XX_CONFIG			0x00
+#define INA2XX_SHUNT_VOLTAGE		0x01 /* readonly */
+#define INA2XX_BUS_VOLTAGE		0x02 /* readonly */
+#define INA2XX_POWER			0x03 /* readonly */
+#define INA2XX_CURRENT			0x04 /* readonly */
+#define INA2XX_CALIBRATION		0x05
+
+/* INA226 register definitions */
+#define INA226_MASK_ENABLE		0x06
+#define INA226_ALERT_LIMIT		0x07
+#define INA226_DIE_ID			0xFF
+
+
+/* register count */
+#define INA219_REGISTERS		6
+#define INA226_REGISTERS		8
+
+#define INA2XX_MAX_REGISTERS		8
+
+/* settings - depend on use case */
+#define INA219_CONFIG_DEFAULT		0x399F	/* PGA=8 */
+#define INA226_CONFIG_DEFAULT		0x4527	/* averages=16 */
+
+/* worst case is 68.10 ms (~14.6Hz, ina219) */
+#define INA2XX_CONVERSION_RATE		15
+
+enum ina2xx_ids { ina219, ina226 };
+
+struct ina2xx_data {
+	struct device *hwmon_dev;
+
+	struct mutex update_lock;
+	bool valid;
+	unsigned long last_updated;
+
+	int kind;
+	int registers;
+	u16 regs[INA2XX_MAX_REGISTERS];
+};
+
+int ina2xx_read_word(struct i2c_client *client, int reg)
+{
+	int val = i2c_smbus_read_word_data(client, reg);
+	if (unlikely(val < 0)) {
+		dev_dbg(&client->dev,
+			"Failed to read register: %d\n", reg);
+		return val;
+	}
+	return be16_to_cpu(val);
+}
+
+void ina2xx_write_word(struct i2c_client *client, int reg, int data)
+{
+	i2c_smbus_write_word_data(client, reg, cpu_to_be16(data));
+}
+
+static struct ina2xx_data *ina2xx_update_device(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct ina2xx_data *data = i2c_get_clientdata(client);
+	struct ina2xx_data *ret = data;
+
+	mutex_lock(&data->update_lock);
+
+	if (time_after(jiffies, data->last_updated +
+		       HZ / INA2XX_CONVERSION_RATE) || !data->valid) {
+
+		int i;
+
+		dev_dbg(&client->dev, "Starting ina2xx update\n");
+
+		/* Read all registers */
+		for (i = 0; i < data->registers; i++) {
+			int rv = ina2xx_read_word(client, i);
+			if (rv < 0) {
+				ret = ERR_PTR(rv);
+				goto abort;
+			}
+			data->regs[i] = rv;
+		}
+		data->last_updated = jiffies;
+		data->valid = 1;
+	}
+abort:
+	mutex_unlock(&data->update_lock);
+	return ret;
+}
+
+static int ina219_get_value(struct ina2xx_data *data, u8 reg)
+{
+	/*
+	 * calculate exact value for the given register
+	 * we assume default power-on reset settings:
+	 * bus voltage range 32V
+	 * gain = /8
+	 * adc 1 & 2 -> conversion time 532uS
+	 * mode is continuous shunt and bus
+	 * calibration value is INA219_CALIBRATION_VALUE
+	 */
+	int val = data->regs[reg];
+
+	switch (reg) {
+	case INA2XX_SHUNT_VOLTAGE:
+		/* LSB=10uV. Convert to mV. */
+		val = DIV_ROUND_CLOSEST(val, 100);
+		break;
+	case INA2XX_BUS_VOLTAGE:
+		/* LSB=4mV. Register is not right aligned, convert to mV. */
+		val = (val >> 3) * 4;
+		break;
+	case INA2XX_POWER:
+		/* LSB=20mW. Convert to uW */
+		val = val * 20 * 1000;
+		break;
+	case INA2XX_CURRENT:
+		/* LSB=1mA (selected). Is in mA */
+		break;
+	default:
+		/* programmer goofed */
+		WARN_ON_ONCE(1);
+		val = 0;
+		break;
+	}
+
+	return val;
+}
+
+static int ina226_get_value(struct ina2xx_data *data, u8 reg)
+{
+	/*
+	 * calculate exact value for the given register
+	 * we assume default power-on reset settings:
+	 * bus voltage range 32V
+	 * gain = /8
+	 * adc 1 & 2 -> conversion time 532uS
+	 * mode is continuous shunt and bus
+	 * calibration value is INA226_CALIBRATION_VALUE
+	 */
+	int val = data->regs[reg];
+
+	switch (reg) {
+	case INA2XX_SHUNT_VOLTAGE:
+		/* LSB=2.5uV. Convert to mV. */
+		val = DIV_ROUND_CLOSEST(val, 400);
+		break;
+	case INA2XX_BUS_VOLTAGE:
+		/* LSB=1.25mV. Convert to mV. */
+		val = val + DIV_ROUND_CLOSEST(val, 4);
+		break;
+	case INA2XX_POWER:
+		/* LSB=25mW. Convert to uW */
+		val = val * 25 * 1000;
+		break;
+	case INA2XX_CURRENT:
+		/* LSB=1mA (selected). Is in mA */
+		break;
+	default:
+		/* programmer goofed */
+		WARN_ON_ONCE(1);
+		val = 0;
+		break;
+	}
+
+	return val;
+}
+
+static ssize_t ina2xx_show_value(struct device *dev,
+				 struct device_attribute *da, char *buf)
+{
+	struct sensor_device_attribute *attr = to_sensor_dev_attr(da);
+	struct ina2xx_data *data = ina2xx_update_device(dev);
+	int value = 0;
+
+	if (IS_ERR(data))
+		return PTR_ERR(data);
+
+	switch (data->kind) {
+	case ina219:
+		value = ina219_get_value(data, attr->index);
+		break;
+	case ina226:
+		value = ina226_get_value(data, attr->index);
+		break;
+	default:
+		WARN_ON_ONCE(1);
+		break;
+	}
+	return snprintf(buf, PAGE_SIZE, "%d\n", value);
+}
+
+/* shunt voltage */
+static SENSOR_DEVICE_ATTR(in0_input, S_IRUGO, \
+	ina2xx_show_value, NULL, INA2XX_SHUNT_VOLTAGE);
+
+/* bus voltage */
+static SENSOR_DEVICE_ATTR(in1_input, S_IRUGO, \
+	ina2xx_show_value, NULL, INA2XX_BUS_VOLTAGE);
+
+/* calculated current */
+static SENSOR_DEVICE_ATTR(curr1_input, S_IRUGO, \
+	ina2xx_show_value, NULL, INA2XX_CURRENT);
+
+/* calculated power */
+static SENSOR_DEVICE_ATTR(power1_input, S_IRUGO, \
+	ina2xx_show_value, NULL, INA2XX_POWER);
+
+/* pointers to created device attributes */
+static struct attribute *ina2xx_attributes[] = {
+	&sensor_dev_attr_in0_input.dev_attr.attr,
+	&sensor_dev_attr_in1_input.dev_attr.attr,
+	&sensor_dev_attr_curr1_input.dev_attr.attr,
+	&sensor_dev_attr_power1_input.dev_attr.attr,
+	NULL,
+};
+
+static const struct attribute_group ina2xx_group = {
+	.attrs = ina2xx_attributes,
+};
+
+static int ina2xx_probe(struct i2c_client *client,
+			const struct i2c_device_id *id)
+{
+	struct i2c_adapter *adapter = client->adapter;
+	struct ina2xx_data *data;
+	struct ina2xx_platform_data *pdata;
+	int ret = 0;
+	long shunt = 10000; /* default shunt value 10mOhms */
+
+	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_WORD_DATA))
+		return -ENODEV;
+
+	data = devm_kzalloc(&client->dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	if (client->dev.platform_data) {
+		pdata =
+		  (struct ina2xx_platform_data *)client->dev.platform_data;
+		shunt = pdata->shunt_uohms;
+	}
+
+	if (shunt <= 0)
+		return -ENODEV;
+
+	/* set the device type */
+	data->kind = id->driver_data;
+
+	switch (data->kind) {
+	case ina219:
+		/* device configuration */
+		ina2xx_write_word(client, INA2XX_CONFIG, INA219_CONFIG_DEFAULT);
+
+		/* set current LSB to 1mA, shunt is in uOhms */
+		/* (equation 13 in datasheet) */
+		ina2xx_write_word(client, INA2XX_CALIBRATION, 40960000 / shunt);
+		dev_info(&client->dev,
+			 "power monitor INA219 (Rshunt = %li uOhm)\n", shunt);
+		data->registers = INA219_REGISTERS;
+		break;
+	case ina226:
+		/* device configuration */
+		ina2xx_write_word(client, INA2XX_CONFIG, INA226_CONFIG_DEFAULT);
+
+		/* set current LSB to 1mA, shunt is in uOhms */
+		/* (equation 1 in datasheet)*/
+		ina2xx_write_word(client, INA2XX_CALIBRATION, 5120000 / shunt);
+		dev_info(&client->dev,
+			 "power monitor INA226 (Rshunt = %li uOhm)\n", shunt);
+		data->registers = INA226_REGISTERS;
+		break;
+	default:
+		/* unknown device id */
+		return -ENODEV;
+	}
+
+	i2c_set_clientdata(client, data);
+	mutex_init(&data->update_lock);
+
+	ret = sysfs_create_group(&client->dev.kobj, &ina2xx_group);
+	if (ret)
+		return ret;
+
+	data->hwmon_dev = hwmon_device_register(&client->dev);
+	if (IS_ERR(data->hwmon_dev)) {
+		ret = PTR_ERR(data->hwmon_dev);
+		goto out_err_hwmon;
+	}
+
+	return 0;
+
+out_err_hwmon:
+	sysfs_remove_group(&client->dev.kobj, &ina2xx_group);
+	return ret;
+}
+
+static int ina2xx_remove(struct i2c_client *client)
+{
+	struct ina2xx_data *data = i2c_get_clientdata(client);
+
+	hwmon_device_unregister(data->hwmon_dev);
+	sysfs_remove_group(&client->dev.kobj, &ina2xx_group);
+
+	return 0;
+}
+
+static const struct i2c_device_id ina2xx_id[] = {
+	{ "ina219", ina219 },
+	{ "ina226", ina226 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, ina2xx_id);
+
+static struct i2c_driver ina2xx_driver = {
+	.driver = {
+		.name	= "ina2xx",
+	},
+	.probe		= ina2xx_probe,
+	.remove		= ina2xx_remove,
+	.id_table	= ina2xx_id,
+};
+
+static int __init ina2xx_init(void)
+{
+	return i2c_add_driver(&ina2xx_driver);
+}
+
+static void __exit ina2xx_exit(void)
+{
+	i2c_del_driver(&ina2xx_driver);
+}
+
+MODULE_AUTHOR("Lothar Felten <l-felten@ti.com>");
+MODULE_DESCRIPTION("ina2xx driver");
+MODULE_LICENSE("GPL");
+
+module_init(ina2xx_init);
+module_exit(ina2xx_exit);

drivers/hwmon/k10temp.c

@@ -225,15 +225,4 @@ static struct pci_driver k10temp_driver = {
 	.remove = __devexit_p(k10temp_remove),
 };
 
-static int __init k10temp_init(void)
-{
-	return pci_register_driver(&k10temp_driver);
-}
-
-static void __exit k10temp_exit(void)
-{
-	pci_unregister_driver(&k10temp_driver);
-}
-
-module_init(k10temp_init)
-module_exit(k10temp_exit)
+module_pci_driver(k10temp_driver);

drivers/hwmon/k8temp.c

@@ -339,19 +339,8 @@ static struct pci_driver k8temp_driver = {
 	.remove = __devexit_p(k8temp_remove),
 };
 
-static int __init k8temp_init(void)
-{
-	return pci_register_driver(&k8temp_driver);
-}
-
-static void __exit k8temp_exit(void)
-{
-	pci_unregister_driver(&k8temp_driver);
-}
+module_pci_driver(k8temp_driver);
 
 MODULE_AUTHOR("Rudolf Marek <r.marek@assembler.cz>");
 MODULE_DESCRIPTION("AMD K8 core temperature monitor");
 MODULE_LICENSE("GPL");
-
-module_init(k8temp_init)
-module_exit(k8temp_exit)

drivers/hwmon/ntc_thermistor.c

@@ -134,8 +134,7 @@ static inline u64 div64_u64_safe(u64 dividend, u64 divisor)
 	return div64_u64(dividend, divisor);
 }
 
-static unsigned int get_ohm_of_thermistor(struct ntc_data *data,
-		unsigned int uV)
+static int get_ohm_of_thermistor(struct ntc_data *data, unsigned int uV)
 {
 	struct ntc_thermistor_platform_data *pdata = data->pdata;
 	u64 mV = uV / 1000;
@@ -146,12 +145,12 @@ static unsigned int get_ohm_of_thermistor(struct ntc_data *data,
 
 	if (mV == 0) {
 		if (pdata->connect == NTC_CONNECTED_POSITIVE)
-			return UINT_MAX;
+			return INT_MAX;
 		return 0;
 	}
 	if (mV >= pmV)
 		return (pdata->connect == NTC_CONNECTED_POSITIVE) ?
-			0 : UINT_MAX;
+			0 : INT_MAX;
 
 	if (pdata->connect == NTC_CONNECTED_POSITIVE && puO == 0)
 		N = div64_u64_safe(pdO * (pmV - mV), mV);
@@ -163,113 +162,109 @@ static unsigned int get_ohm_of_thermistor(struct ntc_data *data,
 	else
 		N = div64_u64_safe(pdO * puO * mV, pdO * (pmV - mV) - puO * mV);
 
-	return (unsigned int) N;
+	if (N > INT_MAX)
+		N = INT_MAX;
+	return N;
 }
 
-static int lookup_comp(struct ntc_data *data,
-		unsigned int ohm, int *i_low, int *i_high)
+static void lookup_comp(struct ntc_data *data, unsigned int ohm,
+			int *i_low, int *i_high)
 {
-	int start, end, mid = -1;
+	int start, end, mid;
+
+	/*
+	 * Handle special cases: Resistance is higher than or equal to
+	 * resistance in first table entry, or resistance is lower or equal
+	 * to resistance in last table entry.
+	 * In these cases, return i_low == i_high, either pointing to the
+	 * beginning or to the end of the table depending on the condition.
+	 */
+	if (ohm >= data->comp[0].ohm) {
+		*i_low = 0;
+		*i_high = 0;
+		return;
+	}
+	if (ohm <= data->comp[data->n_comp - 1].ohm) {
+		*i_low = data->n_comp - 1;
+		*i_high = data->n_comp - 1;
+		return;
+	}
 
 	/* Do a binary search on compensation table */
 	start = 0;
 	end = data->n_comp;
-
-	while (end > start) {
+	while (start < end) {
 		mid = start + (end - start) / 2;
-		if (data->comp[mid].ohm < ohm)
+		/*
+		 * start <= mid < end
+		 * data->comp[start].ohm > ohm >= data->comp[end].ohm
+		 *
+		 * We could check for "ohm == data->comp[mid].ohm" here, but
+		 * that is a quite unlikely condition, and we would have to
+		 * check again after updating start. Check it at the end instead
+		 * for simplicity.
+		 */
+		if (ohm >= data->comp[mid].ohm) {
 			end = mid;
-		else if (data->comp[mid].ohm > ohm)
-			start = mid + 1;
-		else
-			break;
-	}
-
-	if (mid == 0) {
-		if (data->comp[mid].ohm > ohm) {
-			*i_high = mid;
-			*i_low = mid + 1;
-			return 0;
-		} else {
-			*i_low = mid;
-			*i_high = -1;
-			return -EINVAL;
-		}
-	}
-	if (mid == (data->n_comp - 1)) {
-		if (data->comp[mid].ohm <= ohm) {
-			*i_low = mid;
-			*i_high = mid - 1;
-			return 0;
 		} else {
-			*i_low = -1;
-			*i_high = mid;
-			return -EINVAL;
+			start = mid + 1;
+			/*
+			 * ohm >= data->comp[start].ohm might be true here,
+			 * since we set start to mid + 1. In that case, we are
+			 * done. We could keep going, but the condition is quite
+			 * likely to occur, so it is worth checking for it.
+			 */
+			if (ohm >= data->comp[start].ohm)
+				end = start;
 		}
+		/*
+		 * start <= end
+		 * data->comp[start].ohm >= ohm >= data->comp[end].ohm
+		 */
 	}
-
-	if (data->comp[mid].ohm <= ohm) {
-		*i_low = mid;
-		*i_high = mid - 1;
-	} else {
-		*i_low = mid + 1;
-		*i_high = mid;
-	}
-
-	return 0;
+	/*
+	 * start == end
+	 * ohm >= data->comp[end].ohm
+	 */
+	*i_low = end;
+	if (ohm == data->comp[end].ohm)
+		*i_high = end;
+	else
+		*i_high = end - 1;
 }
 
-static int get_temp_mC(struct ntc_data *data, unsigned int ohm, int *temp)
+static int get_temp_mC(struct ntc_data *data, unsigned int ohm)
 {
 	int low, high;
-	int ret;
+	int temp;
 
-	ret = lookup_comp(data, ohm, &low, &high);
-	if (ret) {
+	lookup_comp(data, ohm, &low, &high);
+	if (low == high) {
 		/* Unable to use linear approximation */
-		if (low != -1)
-			*temp = data->comp[low].temp_C * 1000;
-		else if (high != -1)
-			*temp = data->comp[high].temp_C * 1000;
-		else
-			return ret;
+		temp = data->comp[low].temp_C * 1000;
 	} else {
-		*temp = data->comp[low].temp_C * 1000 +
+		temp = data->comp[low].temp_C * 1000 +
 			((data->comp[high].temp_C - data->comp[low].temp_C) *
 			 1000 * ((int)ohm - (int)data->comp[low].ohm)) /
 			((int)data->comp[high].ohm - (int)data->comp[low].ohm);
 	}
-
-	return 0;
+	return temp;
 }
 
-static int ntc_thermistor_read(struct ntc_data *data, int *temp)
+static int ntc_thermistor_get_ohm(struct ntc_data *data)
 {
-	int ret;
-	int read_ohm, read_uV;
-	unsigned int ohm = 0;
-
-	if (data->pdata->read_ohm) {
-		read_ohm = data->pdata->read_ohm();
-		if (read_ohm < 0)
-			return read_ohm;
-		ohm = (unsigned int)read_ohm;
-	}
+	int read_uV;
+
+	if (data->pdata->read_ohm)
+		return data->pdata->read_ohm();
 
 	if (data->pdata->read_uV) {
 		read_uV = data->pdata->read_uV();
 		if (read_uV < 0)
 			return read_uV;
-		ohm = get_ohm_of_thermistor(data, (unsigned int)read_uV);
-	}
-
-	ret = get_temp_mC(data, ohm, temp);
-	if (ret) {
-		dev_dbg(data->dev, "Sensor reading function not available.\n");
-		return ret;
+		return get_ohm_of_thermistor(data, read_uV);
 	}
-
-	return 0;
+	return -EINVAL;
 }
 
 static ssize_t ntc_show_name(struct device *dev,
@@ -290,12 +285,13 @@ static ssize_t ntc_show_temp(struct device *dev,
 		struct device_attribute *attr, char *buf)
 {
 	struct ntc_data *data = dev_get_drvdata(dev);
-	int temp, ret;
+	int ohm;
 
-	ret = ntc_thermistor_read(data, &temp);
-	if (ret)
-		return ret;
-	return sprintf(buf, "%d\n", temp);
+	ohm = ntc_thermistor_get_ohm(data);
+	if (ohm < 0)
+		return ohm;
+
+	return sprintf(buf, "%d\n", get_temp_mC(data, ohm));
 }
 
 static SENSOR_DEVICE_ATTR(temp1_type, S_IRUGO, ntc_show_type, NULL, 0);
@@ -326,14 +322,14 @@ static int __devinit ntc_thermistor_probe(struct platform_device *pdev)
 
 	/* Either one of the two is required. */
 	if (!pdata->read_uV && !pdata->read_ohm) {
-		dev_err(&pdev->dev, "Both read_uV and read_ohm missing."
-				"Need either one of the two.\n");
+		dev_err(&pdev->dev,
+			"Both read_uV and read_ohm missing. Need either one of the two.\n");
 		return -EINVAL;
 	}
 
 	if (pdata->read_uV && pdata->read_ohm) {
-		dev_warn(&pdev->dev, "Only one of read_uV and read_ohm "
-				"is needed; ignoring read_uV.\n");
+		dev_warn(&pdev->dev,
+			 "Only one of read_uV and read_ohm is needed; ignoring read_uV.\n");
 		pdata->read_uV = NULL;
 	}
 
@@ -344,12 +340,12 @@ static int __devinit ntc_thermistor_probe(struct platform_device *pdev)
 				 NTC_CONNECTED_POSITIVE) ||
 				(pdata->connect != NTC_CONNECTED_POSITIVE &&
 				 pdata->connect != NTC_CONNECTED_GROUND))) {
-		dev_err(&pdev->dev, "Required data to use read_uV not "
-				"supplied.\n");
+		dev_err(&pdev->dev,
+			"Required data to use read_uV not supplied.\n");
 		return -EINVAL;
 	}
 
-	data = kzalloc(sizeof(struct ntc_data), GFP_KERNEL);
+	data = devm_kzalloc(&pdev->dev, sizeof(struct ntc_data), GFP_KERNEL);
 	if (!data)
 		return -ENOMEM;
 
@@ -370,8 +366,7 @@ static int __devinit ntc_thermistor_probe(struct platform_device *pdev)
 		dev_err(&pdev->dev, "Unknown device type: %lu(%s)\n",
 				pdev->id_entry->driver_data,
 				pdev->id_entry->name);
-		ret = -EINVAL;
-		goto err;
+		return -EINVAL;
 	}
 
 	platform_set_drvdata(pdev, data);
@@ -379,13 +374,13 @@ static int __devinit ntc_thermistor_probe(struct platform_device *pdev)
 	ret = sysfs_create_group(&data->dev->kobj, &ntc_attr_group);
 	if (ret) {
 		dev_err(data->dev, "unable to create sysfs files\n");
-		goto err;
+		return ret;
 	}
 
 	data->hwmon_dev = hwmon_device_register(data->dev);
-	if (IS_ERR_OR_NULL(data->hwmon_dev)) {
+	if (IS_ERR(data->hwmon_dev)) {
 		dev_err(data->dev, "unable to register as hwmon device.\n");
-		ret = -EINVAL;
+		ret = PTR_ERR(data->hwmon_dev);
 		goto err_after_sysfs;
 	}
 
@@ -395,8 +390,6 @@ static int __devinit ntc_thermistor_probe(struct platform_device *pdev)
 	return 0;
 err_after_sysfs:
 	sysfs_remove_group(&data->dev->kobj, &ntc_attr_group);
-err:
-	kfree(data);
 	return ret;
 }
 
@@ -408,8 +401,6 @@ static int __devexit ntc_thermistor_remove(struct platform_device *pdev)
 	sysfs_remove_group(&data->dev->kobj, &ntc_attr_group);
 	platform_set_drvdata(pdev, NULL);
 
-	kfree(data);
-
 	return 0;
 }
 

include/linux/platform_data/ina2xx.h

+/*
+ * Driver for Texas Instruments INA219, INA226 power monitor chips
+ *
+ * Copyright (C) 2012 Lothar Felten <l-felten@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * For further information, see the Documentation/hwmon/ina2xx file.
+ */
+
+/**
+ * struct ina2xx_platform_data - ina2xx info
+ * @shunt_uohms		shunt resistance in microohms
+ */
+struct ina2xx_platform_data {
+	long shunt_uohms;
+};