Commit 132aa220 authored by Tomas Henzl's avatar Tomas Henzl Committed by Christoph Hellwig

hpsa: refine the pci enable/disable handling

When a second(kdump) kernel starts and the hard reset method is used
the driver calls pci_disable_device without previously enabling it,
so the kernel shows a warning -
[   16.876248] WARNING: at drivers/pci/pci.c:1431 pci_disable_device+0x84/0x90()
[   16.882686] Device hpsa
disabling already-disabled device
...
This patch fixes it, in addition to this I tried to balance also some other pairs
of enable/disable device in the driver.
Unfortunately I wasn't able to verify the functionality for the case of a sw reset,
because of a lack of proper hw.
Signed-off-by: default avatarTomas Henzl <thenzl@redhat.com>
Reviewed-by: default avatarStephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: default avatarChristoph Hellwig <hch@lst.de>
parent 9e032845
......@@ -5971,10 +5971,6 @@ static int hpsa_kdump_hard_reset_controller(struct pci_dev *pdev)
/* Save the PCI command register */
pci_read_config_word(pdev, 4, &command_register);
/* Turn the board off. This is so that later pci_restore_state()
* won't turn the board on before the rest of config space is ready.
*/
pci_disable_device(pdev);
pci_save_state(pdev);
/* find the first memory BAR, so we can find the cfg table */
......@@ -6022,11 +6018,6 @@ static int hpsa_kdump_hard_reset_controller(struct pci_dev *pdev)
goto unmap_cfgtable;
pci_restore_state(pdev);
rc = pci_enable_device(pdev);
if (rc) {
dev_warn(&pdev->dev, "failed to enable device.\n");
goto unmap_cfgtable;
}
pci_write_config_word(pdev, 4, command_register);
/* Some devices (notably the HP Smart Array 5i Controller)
......@@ -6537,6 +6528,23 @@ static int hpsa_init_reset_devices(struct pci_dev *pdev)
if (!reset_devices)
return 0;
/* kdump kernel is loading, we don't know in which state is
* the pci interface. The dev->enable_cnt is equal zero
* so we call enable+disable, wait a while and switch it on.
*/
rc = pci_enable_device(pdev);
if (rc) {
dev_warn(&pdev->dev, "Failed to enable PCI device\n");
return -ENODEV;
}
pci_disable_device(pdev);
msleep(260); /* a randomly chosen number */
rc = pci_enable_device(pdev);
if (rc) {
dev_warn(&pdev->dev, "failed to enable device.\n");
return -ENODEV;
}
/* Reset the controller with a PCI power-cycle or via doorbell */
rc = hpsa_kdump_hard_reset_controller(pdev);
......@@ -6545,10 +6553,11 @@ static int hpsa_init_reset_devices(struct pci_dev *pdev)
* "performant mode". Or, it might be 640x, which can't reset
* due to concerns about shared bbwc between 6402/6404 pair.
*/
if (rc == -ENOTSUPP)
return rc; /* just try to do the kdump anyhow. */
if (rc)
return -ENODEV;
if (rc) {
if (rc != -ENOTSUPP) /* just try to do the kdump anyhow. */
rc = -ENODEV;
goto out_disable;
}
/* Now try to get the controller to respond to a no-op */
dev_warn(&pdev->dev, "Waiting for controller to respond to no-op\n");
......@@ -6559,7 +6568,11 @@ static int hpsa_init_reset_devices(struct pci_dev *pdev)
dev_warn(&pdev->dev, "no-op failed%s\n",
(i < 11 ? "; re-trying" : ""));
}
return 0;
out_disable:
pci_disable_device(pdev);
return rc;
}
static int hpsa_allocate_cmd_pool(struct ctlr_info *h)
......@@ -6739,6 +6752,7 @@ static void hpsa_undo_allocations_after_kdump_soft_reset(struct ctlr_info *h)
iounmap(h->transtable);
if (h->cfgtable)
iounmap(h->cfgtable);
pci_disable_device(h->pdev);
pci_release_regions(h->pdev);
kfree(h);
}
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment