ARM: dts: add Armadeus Systems OPOS6UL and OPOS6ULDEV support

OPOS6UL is an i.MX6UL based SoM.
OPOS6ULDev is a carrier board for the OPOS6UL SoM.

For more details see:
http://www.opossom.com/english/products-processor_boards-opos6ul.html
http://www.opossom.com/english/products-development_boards-opos6ul_dev.htmlSigned-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>

arch/arm/boot/dts/Makefile

@@ -440,6 +440,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
 	imx6ul-geam-kit.dtb \
 	imx6ul-isiot.dtb \
 	imx6ul-liteboard.dtb \
+	imx6ul-opos6uldev.dtb \
 	imx6ul-pico-hobbit.dtb \
 	imx6ul-tx6ul-0010.dtb \
 	imx6ul-tx6ul-0011.dtb \

arch/arm/boot/dts/imx6ul-opos6ul.dtsi

+/*
+ * Copyright 2017 Armadeus Systems <support@armadeus.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of
+ *     the License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ *     You should have received a copy of the GNU General Public
+ *     License along with this file; if not, write to the Free
+ *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ *     MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "imx6ul.dtsi"
+
+/ {
+	memory {
+		reg = <0x80000000 0>; /* will be filled by U-Boot */
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	usdhc3_pwrseq: usdhc3-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio2 9 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>;
+	phy-mode = "rmii";
+	phy-reset-duration = <1>;
+	phy-reset-gpios = <&gpio4 2 GPIO_ACTIVE_LOW>;
+	phy-handle = <&ethphy1>;
+	phy-supply = <&reg_3v3>;
+	status = "okay";
+
+	mdio: mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy1: ethernet-phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+			interrupt-parent = <&gpio4>;
+			interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
+			status = "okay";
+		};
+	};
+};
+
+/* Bluetooth */
+&uart8 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart8>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+/* eMMC */
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	bus-width = <8>;
+	no-1-8-v;
+	non-removable;
+	status = "okay";
+};
+
+/* WiFi */
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	bus-width = <4>;
+	no-1-8-v;
+	non-removable;
+	mmc-pwrseq = <&usdhc3_pwrseq>;
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	brcmf: bcrmf@1 {
+		compatible = "brcm,bcm4329-fmac";
+		reg = <1>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-names = "host-wake";
+	};
+};
+
+&iomuxc {
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO06__ENET1_MDIO	0x1b0b0
+			MX6UL_PAD_GPIO1_IO07__ENET1_MDC		0x1b0b0
+			MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER	0x130b0
+			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN	0x130b0
+			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01	0x130b0
+			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00	0x130b0
+			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00	0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01	0x1b0b0
+			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN	0x1b0b0
+			/* INT# */
+			MX6UL_PAD_NAND_DQS__GPIO4_IO16		0x1b0b0
+			/* RST# */
+			MX6UL_PAD_NAND_DATA00__GPIO4_IO02	0x130b0
+			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1	0x4001b031
+		>;
+	};
+
+	pinctrl_uart8: uart8grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_TX_EN__UART8_DCE_RX	0x1b0b0
+			MX6UL_PAD_ENET2_TX_DATA1__UART8_DCE_TX	0x1b0b0
+			MX6UL_PAD_ENET2_RX_ER__UART8_DCE_RTS	0x1b0b0
+			MX6UL_PAD_ENET2_TX_CLK__UART8_DCE_CTS	0x1b0b0
+			/* BT_REG_ON */
+			MX6UL_PAD_ENET2_RX_EN__GPIO2_IO10	0x130b0
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x17059
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x10059
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x17059
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x17059
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x17059
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x17059
+			MX6UL_PAD_NAND_READY_B__USDHC1_DATA4	0x17059
+			MX6UL_PAD_NAND_CE0_B__USDHC1_DATA5	0x17059
+			MX6UL_PAD_NAND_CE1_B__USDHC1_DATA6	0x17059
+			MX6UL_PAD_NAND_CLE__USDHC1_DATA7	0x17059
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA18__USDHC2_CMD	0x1b0b0
+			MX6UL_PAD_LCD_DATA19__USDHC2_CLK	0x100b0
+			MX6UL_PAD_LCD_DATA20__USDHC2_DATA0	0x1b0b0
+			MX6UL_PAD_LCD_DATA21__USDHC2_DATA1	0x1b0b0
+			MX6UL_PAD_LCD_DATA22__USDHC2_DATA2	0x1b0b0
+			MX6UL_PAD_LCD_DATA23__USDHC2_DATA3	0x1b0b0
+			/* WL_REG_ON */
+			MX6UL_PAD_ENET2_RX_DATA1__GPIO2_IO09	0x130b0
+			/* WL_IRQ */
+			MX6UL_PAD_ENET2_RX_DATA0__GPIO2_IO08	0x1b0b0
+		>;
+	};
+};