Merge branch 'exynos-drm-next' of...

Merge branch 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-next

Summaries:
- Add MIPI-DSI Driver, and dt bindigs
- Add S6E8AA0 MIPI-DSI based panel drivers, and dt bindings
- Add LD9040 parallel panel driver
 . this driver is placed in drivers/gpu/drm/panel, and it seems
   to be used for exynos drm as of now,
- Some fixups

Changelog v2:
- Remove super device support, and relevant dt bindings for more reviews.
- Fix module build errors you pointed out.
- Re-based it to drm-next again.

* 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
  drm/bridge: export ptn3460_init function
  drm/exynos: remove MODULE_DEVICE_TABLE definitions
  ARM: dts: exynos4412-trats2: enable exynos/fimd node
  ARM: dts: exynos4210-trats: enable exynos/fimd node
  ARM: dts: exynos4412-trats2: add panel node
  ARM: dts: exynos4210-trats: add panel node
  ARM: dts: exynos4: add MIPI DSI Master node
  drm/panel: add S6E8AA0 driver
  ARM: dts: exynos4210-universal_c210: add proper panel node
  drm/panel: add ld9040 driver
  panel/ld9040: add DT bindings
  panel/s6e8aa0: add DT bindings
  drm/exynos: add DSIM driver
  exynos/dsim: add DT bindings
  drm/exynos: disallow fbdev initialization if no device is connected
  drm/mipi_dsi: create dsi devices only for nodes with reg property
  drm/mipi_dsi: add flags to DSI messages

Documentation/devicetree/bindings/panel/samsung,ld9040.txt

+Samsung LD9040 AMOLED LCD parallel RGB panel with SPI control bus
+
+Required properties:
+  - compatible: "samsung,ld9040"
+  - reg: address of the panel on SPI bus
+  - vdd3-supply: core voltage supply
+  - vci-supply: voltage supply for analog circuits
+  - reset-gpios: a GPIO spec for the reset pin
+  - display-timings: timings for the connected panel according to [1]
+
+The panel must obey rules for SPI slave device specified in document [2].
+
+Optional properties:
+  - power-on-delay: delay after turning regulators on [ms]
+  - reset-delay: delay after reset sequence [ms]
+  - panel-width-mm: physical panel width [mm]
+  - panel-height-mm: physical panel height [mm]
+
+The device node can contain one 'port' child node with one child
+'endpoint' node, according to the bindings defined in [3]. This
+node should describe panel's video bus.
+
+[1]: Documentation/devicetree/bindings/video/display-timing.txt
+[2]: Documentation/devicetree/bindings/spi/spi-bus.txt
+[3]: Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Example:
+
+	lcd@0 {
+		compatible = "samsung,ld9040";
+		reg = <0>;
+		vdd3-supply = <&ldo7_reg>;
+		vci-supply = <&ldo17_reg>;
+		reset-gpios = <&gpy4 5 0>;
+		spi-max-frequency = <1200000>;
+		spi-cpol;
+		spi-cpha;
+		power-on-delay = <10>;
+		reset-delay = <10>;
+		panel-width-mm = <90>;
+		panel-height-mm = <154>;
+
+		display-timings {
+			timing {
+				clock-frequency = <23492370>;
+				hactive = <480>;
+				vactive = <800>;
+				hback-porch = <16>;
+				hfront-porch = <16>;
+				vback-porch = <2>;
+				vfront-porch = <28>;
+				hsync-len = <2>;
+				vsync-len = <1>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <0>;
+				pixelclk-active = <0>;
+			};
+		};
+
+		port {
+			lcd_ep: endpoint {
+				remote-endpoint = <&fimd_dpi_ep>;
+			};
+		};
+	};

Documentation/devicetree/bindings/panel/samsung,s6e8aa0.txt

+Samsung S6E8AA0 AMOLED LCD 5.3 inch panel
+
+Required properties:
+  - compatible: "samsung,s6e8aa0"
+  - reg: the virtual channel number of a DSI peripheral
+  - vdd3-supply: core voltage supply
+  - vci-supply: voltage supply for analog circuits
+  - reset-gpios: a GPIO spec for the reset pin
+  - display-timings: timings for the connected panel as described by [1]
+
+Optional properties:
+  - power-on-delay: delay after turning regulators on [ms]
+  - reset-delay: delay after reset sequence [ms]
+  - init-delay: delay after initialization sequence [ms]
+  - panel-width-mm: physical panel width [mm]
+  - panel-height-mm: physical panel height [mm]
+  - flip-horizontal: boolean to flip image horizontally
+  - flip-vertical: boolean to flip image vertically
+
+The device node can contain one 'port' child node with one child
+'endpoint' node, according to the bindings defined in [2]. This
+node should describe panel's video bus.
+
+[1]: Documentation/devicetree/bindings/video/display-timing.txt
+[2]: Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Example:
+
+	panel {
+		compatible = "samsung,s6e8aa0";
+		reg = <0>;
+		vdd3-supply = <&vcclcd_reg>;
+		vci-supply = <&vlcd_reg>;
+		reset-gpios = <&gpy4 5 0>;
+		power-on-delay= <50>;
+		reset-delay = <100>;
+		init-delay = <100>;
+		panel-width-mm = <58>;
+		panel-height-mm = <103>;
+		flip-horizontal;
+		flip-vertical;
+
+		display-timings {
+			timing0: timing-0 {
+				clock-frequency = <57153600>;
+				hactive = <720>;
+				vactive = <1280>;
+				hfront-porch = <5>;
+				hback-porch = <5>;
+				hsync-len = <5>;
+				vfront-porch = <13>;
+				vback-porch = <1>;
+				vsync-len = <2>;
+			};
+		};
+	};

Documentation/devicetree/bindings/video/exynos_dsim.txt

+Exynos MIPI DSI Master
+
+Required properties:
+  - compatible: "samsung,exynos4210-mipi-dsi"
+  - reg: physical base address and length of the registers set for the device
+  - interrupts: should contain DSI interrupt
+  - clocks: list of clock specifiers, must contain an entry for each required
+    entry in clock-names
+  - clock-names: should include "bus_clk"and "pll_clk" entries
+  - phys: list of phy specifiers, must contain an entry for each required
+    entry in phy-names
+  - phy-names: should include "dsim" entry
+  - vddcore-supply: MIPI DSIM Core voltage supply (e.g. 1.1V)
+  - vddio-supply: MIPI DSIM I/O and PLL voltage supply (e.g. 1.8V)
+  - samsung,pll-clock-frequency: specifies frequency of the "pll_clk" clock
+  - #address-cells, #size-cells: should be set respectively to <1> and <0>
+    according to DSI host bindings (see MIPI DSI bindings [1])
+
+Optional properties:
+  - samsung,power-domain: a phandle to DSIM power domain node
+
+Child nodes:
+  Should contain DSI peripheral nodes (see MIPI DSI bindings [1]).
+
+Video interfaces:
+  Device node can contain video interface port nodes according to [2].
+  The following are properties specific to those nodes:
+
+  port node:
+    - reg: (required) can be 0 for input RGB/I80 port or 1 for DSI port;
+
+  endpoint node of DSI port (reg = 1):
+    - samsung,burst-clock-frequency: specifies DSI frequency in high-speed burst
+      mode
+    - samsung,esc-clock-frequency: specifies DSI frequency in escape mode
+
+[1]: Documentation/devicetree/bindings/mipi/dsi/mipi-dsi-bus.txt
+[2]: Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Example:
+
+	dsi@11C80000 {
+		compatible = "samsung,exynos4210-mipi-dsi";
+		reg = <0x11C80000 0x10000>;
+		interrupts = <0 79 0>;
+		clocks = <&clock 286>, <&clock 143>;
+		clock-names = "bus_clk", "pll_clk";
+		phys = <&mipi_phy 1>;
+		phy-names = "dsim";
+		vddcore-supply = <&vusb_reg>;
+		vddio-supply = <&vmipi_reg>;
+		samsung,power-domain = <&pd_lcd0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		samsung,pll-clock-frequency = <24000000>;
+
+		panel@1 {
+			reg = <0>;
+			...
+			port {
+				panel_ep: endpoint {
+					remote-endpoint = <&dsi_ep>;
+				};
+			};
+		};
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@1 {
+				dsi_ep: endpoint {
+					reg = <0>;
+					samsung,burst-clock-frequency = <500000000>;
+					samsung,esc-clock-frequency = <20000000>;
+					remote-endpoint = <&panel_ep>;
+				};
+			};
+		};
+	};

arch/arm/boot/dts/exynos4.dtsi

@@ -104,6 +104,20 @@ sys_reg: syscon@10010000 {
 		reg = <0x10010000 0x400>;
 	};
 
+	dsi_0: dsi@11C80000 {
+		compatible = "samsung,exynos4210-mipi-dsi";
+		reg = <0x11C80000 0x10000>;
+		interrupts = <0 79 0>;
+		samsung,power-domain = <&pd_lcd0>;
+		phys = <&mipi_phy 1>;
+		phy-names = "dsim";
+		clocks = <&clock 286>, <&clock 143>;
+		clock-names = "bus_clk", "pll_clk";
+		status = "disabled";
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
 	camera {
 		compatible = "samsung,fimc", "simple-bus";
 		status = "disabled";

arch/arm/boot/dts/exynos4210-trats.dts

@@ -353,6 +353,67 @@ xusbxti {
 		};
 	};
 
+	dsi_0: dsi@11C80000 {
+		vddcore-supply = <&vusb_reg>;
+		vddio-supply = <&vmipi_reg>;
+		samsung,pll-clock-frequency = <24000000>;
+		status = "okay";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@1 {
+				reg = <1>;
+
+				dsi_out: endpoint {
+					remote-endpoint = <&dsi_in>;
+					samsung,burst-clock-frequency = <500000000>;
+					samsung,esc-clock-frequency = <20000000>;
+				};
+			};
+		};
+
+		panel@0 {
+			reg = <0>;
+			compatible = "samsung,s6e8aa0";
+			vdd3-supply = <&vcclcd_reg>;
+			vci-supply = <&vlcd_reg>;
+			reset-gpios = <&gpy4 5 0>;
+			power-on-delay= <50>;
+			reset-delay = <100>;
+			init-delay = <100>;
+			flip-horizontal;
+			flip-vertical;
+			panel-width-mm = <58>;
+			panel-height-mm = <103>;
+
+			display-timings {
+				timing-0 {
+					clock-frequency = <57153600>;
+					hactive = <720>;
+					vactive = <1280>;
+					hfront-porch = <5>;
+					hback-porch = <5>;
+					hsync-len = <5>;
+					vfront-porch = <13>;
+					vback-porch = <1>;
+					vsync-len = <2>;
+				};
+			};
+
+			port {
+				dsi_in: endpoint {
+					remote-endpoint = <&dsi_out>;
+				};
+			};
+		};
+	};
+
+	fimd@11c00000 {
+		status = "okay";
+	};
+
 	camera {
 		pinctrl-names = "default";
 		pinctrl-0 = <>;

arch/arm/boot/dts/exynos4210-universal_c210.dts

@@ -225,7 +225,6 @@ ldo7_reg: LDO7 {
 					regulator-name = "VLCD+VMIPI_1.8V";
 					regulator-min-microvolt = <1800000>;
 					regulator-max-microvolt = <1800000>;
-					regulator-always-on;
 				};
 
 				ldo8_reg: LDO8 {
@@ -289,7 +288,6 @@ ldo17_reg: LDO17 {
 					regulator-name = "VCC_3.0V_LCD";
 					regulator-min-microvolt = <3000000>;
 					regulator-max-microvolt = <3000000>;
-					regulator-always-on;
 				};
 
 				buck1_reg: BUCK1 {
@@ -347,27 +345,66 @@ safeout2_reg: ESAFEOUT2 {
 		};
 	};
 
+	spi-lcd {
+		compatible = "spi-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-sck = <&gpy3 1 0>;
+		gpio-mosi = <&gpy3 3 0>;
+		num-chipselects = <1>;
+		cs-gpios = <&gpy4 3 0>;
+
+		lcd@0 {
+			compatible = "samsung,ld9040";
+			reg = <0>;
+			vdd3-supply = <&ldo7_reg>;
+			vci-supply = <&ldo17_reg>;
+			reset-gpios = <&gpy4 5 0>;
+			spi-max-frequency = <1200000>;
+			spi-cpol;
+			spi-cpha;
+			power-on-delay = <10>;
+			reset-delay = <10>;
+			panel-width-mm = <90>;
+			panel-height-mm = <154>;
+			display-timings {
+				timing {
+					clock-frequency = <23492370>;
+					hactive = <480>;
+					vactive = <800>;
+					hback-porch = <16>;
+					hfront-porch = <16>;
+					vback-porch = <2>;
+					vfront-porch = <28>;
+					hsync-len = <2>;
+					vsync-len = <1>;
+					hsync-active = <0>;
+					vsync-active = <0>;
+					de-active = <0>;
+					pixelclk-active = <0>;
+				};
+			};
+			port {
+				lcd_ep: endpoint {
+					remote-endpoint = <&fimd_dpi_ep>;
+				};
+			};
+		};
+	};
+
 	fimd: fimd@11c00000 {
 		pinctrl-0 = <&lcd_clk>, <&lcd_data24>;
 		pinctrl-names = "default";
 		status = "okay";
 		samsung,invert-vden;
 		samsung,invert-vclk;
-		display-timings {
-			timing {
-				clock-frequency = <23492370>;
-				hactive = <480>;
-				vactive = <800>;
-				hback-porch = <16>;
-				hfront-porch = <16>;
-				vback-porch = <2>;
-				vfront-porch = <28>;
-				hsync-len = <2>;
-				vsync-len = <1>;
-				hsync-active = <0>;
-				vsync-active = <0>;
-				de-active = <0>;
-				pixelclk-active = <0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		port@3 {
+			reg = <3>;
+			fimd_dpi_ep: endpoint {
+				remote-endpoint = <&lcd_ep>;
 			};
 		};
 	};

arch/arm/boot/dts/exynos4412-trats2.dts

@@ -71,6 +71,15 @@ cam_io_reg: voltage-regulator-1 {
 			enable-active-high;
 		};
 
+		lcd_vdd3_reg: voltage-regulator-2 {
+			compatible = "regulator-fixed";
+			regulator-name = "LCD_VDD_2.2V";
+			regulator-min-microvolt = <2200000>;
+			regulator-max-microvolt = <2200000>;
+			gpio = <&gpc0 1 0>;
+			enable-active-high;
+		};
+
 		/* More to come */
 	};
 
@@ -511,6 +520,67 @@ controller-data {
 		};
 	};
 
+	dsi_0: dsi@11C80000 {
+		vddcore-supply = <&ldo8_reg>;
+		vddio-supply = <&ldo10_reg>;
+		samsung,pll-clock-frequency = <24000000>;
+		status = "okay";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@1 {
+				reg = <1>;
+
+				dsi_out: endpoint {
+					remote-endpoint = <&dsi_in>;
+					samsung,burst-clock-frequency = <500000000>;
+					samsung,esc-clock-frequency = <20000000>;
+				};
+			};
+		};
+
+		panel@0 {
+			compatible = "samsung,s6e8aa0";
+			reg = <0>;
+			vdd3-supply = <&lcd_vdd3_reg>;
+			vci-supply = <&ldo25_reg>;
+			reset-gpios = <&gpy4 5 0>;
+			power-on-delay= <50>;
+			reset-delay = <100>;
+			init-delay = <100>;
+			flip-horizontal;
+			flip-vertical;
+			panel-width-mm = <58>;
+			panel-height-mm = <103>;
+
+			display-timings {
+				timing-0 {
+					clock-frequency = <0>;
+					hactive = <720>;
+					vactive = <1280>;
+					hfront-porch = <5>;
+					hback-porch = <5>;
+					hsync-len = <5>;
+					vfront-porch = <13>;
+					vback-porch = <1>;
+					vsync-len = <2>;
+				};
+			};
+
+			port {
+				dsi_in: endpoint {
+					remote-endpoint = <&dsi_out>;
+				};
+			};
+		};
+	};
+
+	fimd@11c00000 {
+		status = "okay";
+	};
+
 	camera {
 		pinctrl-0 = <&cam_port_b_clk_active>;
 		pinctrl-names = "default";

drivers/gpu/drm/bridge/ptn3460.c

@@ -347,3 +347,4 @@ int ptn3460_init(struct drm_device *dev, struct drm_encoder *encoder,
 		gpio_free(ptn_bridge->gpio_rst_n);
 	return ret;
 }
+EXPORT_SYMBOL(ptn3460_init);

drivers/gpu/drm/drm_mipi_dsi.c

@@ -142,8 +142,12 @@ int mipi_dsi_host_register(struct mipi_dsi_host *host)
 {
 	struct device_node *node;
 
-	for_each_available_child_of_node(host->dev->of_node, node)
+	for_each_available_child_of_node(host->dev->of_node, node) {
+		/* skip nodes without reg property */
+		if (!of_find_property(node, "reg", NULL))
+			continue;
 		of_mipi_dsi_device_add(host, node);
+	}
 
 	return 0;
 }

drivers/gpu/drm/exynos/Kconfig

@@ -39,6 +39,15 @@ config DRM_EXYNOS_DPI
 	help
 	  This enables support for Exynos parallel output.
 
+config DRM_EXYNOS_DSI
+	bool "EXYNOS DRM MIPI-DSI driver support"
+	depends on DRM_EXYNOS
+	select DRM_MIPI_DSI
+	select DRM_PANEL
+	default n
+	help
+	  This enables support for Exynos MIPI-DSI device.
+
 config DRM_EXYNOS_DP
 	bool "EXYNOS DRM DP driver support"
 	depends on DRM_EXYNOS && ARCH_EXYNOS

drivers/gpu/drm/exynos/Makefile

@@ -12,6 +12,7 @@ exynosdrm-$(CONFIG_DRM_EXYNOS_IOMMU) += exynos_drm_iommu.o
 exynosdrm-$(CONFIG_DRM_EXYNOS_DMABUF) += exynos_drm_dmabuf.o
 exynosdrm-$(CONFIG_DRM_EXYNOS_FIMD)	+= exynos_drm_fimd.o
 exynosdrm-$(CONFIG_DRM_EXYNOS_DPI)	+= exynos_drm_dpi.o
+exynosdrm-$(CONFIG_DRM_EXYNOS_DSI)	+= exynos_drm_dsi.o
 exynosdrm-$(CONFIG_DRM_EXYNOS_DP)	+= exynos_dp_core.o exynos_dp_reg.o
 exynosdrm-$(CONFIG_DRM_EXYNOS_HDMI)	+= exynos_hdmi.o exynos_mixer.o
 exynosdrm-$(CONFIG_DRM_EXYNOS_VIDI)	+= exynos_drm_vidi.o

drivers/gpu/drm/exynos/exynos_dp_core.c

@@ -1339,7 +1339,6 @@ static const struct of_device_id exynos_dp_match[] = {
 	{ .compatible = "samsung,exynos5-dp" },
 	{},
 };
-MODULE_DEVICE_TABLE(of, exynos_dp_match);
 
 struct platform_driver dp_driver = {
 	.probe		= exynos_dp_probe,

drivers/gpu/drm/exynos/exynos_drm_drv.c

@@ -450,6 +450,12 @@ static int __init exynos_drm_init(void)
 		goto out_dp;
 #endif
 
+#ifdef CONFIG_DRM_EXYNOS_DSI
+	ret = platform_driver_register(&dsi_driver);
+	if (ret < 0)
+		goto out_dsi;
+#endif
+
 #ifdef CONFIG_DRM_EXYNOS_FIMD
 	ret = platform_driver_register(&fimd_driver);
 	if (ret < 0)
@@ -566,6 +572,11 @@ static int __init exynos_drm_init(void)
 out_fimd:
 #endif
 
+#ifdef CONFIG_DRM_EXYNOS_DSI
+	platform_driver_unregister(&dsi_driver);
+out_dsi:
+#endif
+
 #ifdef CONFIG_DRM_EXYNOS_DP
 	platform_driver_unregister(&dp_driver);
 out_dp:
@@ -613,6 +624,10 @@ static void __exit exynos_drm_exit(void)
 	platform_driver_unregister(&fimd_driver);
 #endif
 
+#ifdef CONFIG_DRM_EXYNOS_DSI
+	platform_driver_unregister(&dsi_driver);
+#endif
+
 #ifdef CONFIG_DRM_EXYNOS_DP
 	platform_driver_unregister(&dp_driver);
 #endif

drivers/gpu/drm/exynos/exynos_drm_drv.h

@@ -370,6 +370,7 @@ static inline int exynos_dpi_remove(struct device *dev) { return 0; }
 #endif
 
 extern struct platform_driver dp_driver;
+extern struct platform_driver dsi_driver;
 extern struct platform_driver fimd_driver;
 extern struct platform_driver hdmi_driver;
 extern struct platform_driver mixer_driver;

drivers/gpu/drm/exynos/exynos_drm_fbdev.c

@@ -237,6 +237,24 @@ static struct drm_fb_helper_funcs exynos_drm_fb_helper_funcs = {
 	.fb_probe =	exynos_drm_fbdev_create,
 };
 
+bool exynos_drm_fbdev_is_anything_connected(struct drm_device *dev)
+{
+	struct drm_connector *connector;
+	bool ret = false;
+
+	mutex_lock(&dev->mode_config.mutex);
+	list_for_each_entry(connector, &dev->mode_config.connector_list, head) {
+		if (connector->status != connector_status_connected)
+			continue;
+
+		ret = true;
+		break;
+	}
+	mutex_unlock(&dev->mode_config.mutex);
+
+	return ret;
+}
+
 int exynos_drm_fbdev_init(struct drm_device *dev)
 {
 	struct exynos_drm_fbdev *fbdev;
@@ -248,6 +266,9 @@ int exynos_drm_fbdev_init(struct drm_device *dev)
 	if (!dev->mode_config.num_crtc || !dev->mode_config.num_connector)
 		return 0;
 
+	if (!exynos_drm_fbdev_is_anything_connected(dev))
+		return 0;
+
 	fbdev = kzalloc(sizeof(*fbdev), GFP_KERNEL);
 	if (!fbdev)
 		return -ENOMEM;

drivers/gpu/drm/panel/Kconfig

@@ -16,4 +16,18 @@ config DRM_PANEL_SIMPLE
 	  that it can be automatically turned off when the panel goes into a
 	  low power state.
 
+config DRM_PANEL_LD9040
+	tristate "LD9040 RGB/SPI panel"
+	depends on DRM && DRM_PANEL
+	depends on OF
+	select SPI
+	select VIDEOMODE_HELPERS
+
+config DRM_PANEL_S6E8AA0
+	tristate "S6E8AA0 DSI video mode panel"
+	depends on DRM && DRM_PANEL
+	depends on OF
+	select DRM_MIPI_DSI
+	select VIDEOMODE_HELPERS
+
 endmenu

drivers/gpu/drm/panel/Makefile

 obj-$(CONFIG_DRM_PANEL_SIMPLE) += panel-simple.o
+obj-$(CONFIG_DRM_PANEL_LD9040) += panel-ld9040.o
+obj-$(CONFIG_DRM_PANEL_S6E8AA0) += panel-s6e8aa0.o

include/drm/drm_mipi_dsi.h

@@ -17,6 +17,11 @@
 struct mipi_dsi_host;
 struct mipi_dsi_device;
 
+/* request ACK from peripheral */
+#define MIPI_DSI_MSG_REQ_ACK	BIT(0)
+/* use Low Power Mode to transmit message */
+#define MIPI_DSI_MSG_USE_LPM	BIT(1)
+
 /**
  * struct mipi_dsi_msg - read/write DSI buffer
  * @channel: virtual channel id
@@ -29,6 +34,7 @@ struct mipi_dsi_device;
 struct mipi_dsi_msg {
 	u8 channel;
 	u8 type;
+	u16 flags;
 
 	size_t tx_len;
 	const void *tx_buf;