ARM: mvebu: dts: Add dts file for DLink DNS-327L

DNS-327L is a 2-bay NAS with the following specs:
     - 512MiB RAM
     - 128MiB NAND Flash
     - 1 GbE interface (Marvell PHY)
     - 1 rear USB 3.0 port (via PCIe USB 3.0 controller)
     - 2 internal SATA ports handled by the Armada 370:
       	 uses 2 gpios for power control
     - two front 2-color leds (amber + white) for both discs,
        controlled by the SoC
     - One white LED handled by SoC (USB)
     - 3 buttons. Power handled by weltrend, USB and
       RESET (on the bottom) are wired via GPIOs
     - Unidentified i2c device at address 0x13 (via i2cdetect)
     - UART0 providing serial console
     - Weltrend MCU serving for RTC, temperature, fan control,
       and power button handling interfaced via UART1
       (Handled via userspace dns320l-daemon)
Signed-off-by: Andrew Andrianov <andrew@ncrmnt.org>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

arch/arm/boot/dts/Makefile

@@ -624,6 +624,7 @@ dtb-$(CONFIG_ARCH_ZYNQ) += \
 	zynq-zybo.dtb
 dtb-$(CONFIG_MACH_ARMADA_370) += \
 	armada-370-db.dtb \
+	armada-370-dlink-dns327l.dtb \
 	armada-370-mirabox.dtb \
 	armada-370-netgear-rn102.dtb \
 	armada-370-netgear-rn104.dtb \

arch/arm/boot/dts/armada-370-dlink-dns327l.dts

+/*
+ * Device Tree file for D-Link DNS-327L
+ *
+ * Copyright (C) 2015, Andrew Andrianov <andrew@ncrmnt.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/* Remaining unsolved:
+ * There's still some unknown device on i2c address 0x13
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "armada-370.dtsi"
+
+/ {
+	model = "D-Link DNS-327L";
+	compatible = "dlink,dns327l",
+		"marvell,armada370",
+		"marvell,armada-370-xp";
+
+	chosen {
+		stdout-path = &uart0;
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>; /* 512 MiB */
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xd0000000 0x100000
+			MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000>;
+
+		pcie-controller {
+			status = "okay";
+
+			pcie@1,0 {
+				/* Port 0, Lane 0 */
+				status = "okay";
+			};
+
+			pcie@2,0 {
+				/* Port 1, Lane 0 */
+				status = "okay";
+			};
+		};
+
+		internal-regs {
+			sata@a0000 {
+				nr-ports = <2>;
+				status = "okay";
+			};
+
+			usb@50000 {
+				status = "okay";
+			};
+
+			nand@d0000 {
+				status = "okay";
+				num-cs = <1>;
+				marvell,nand-keep-config;
+				marvell,nand-enable-arbiter;
+				nand-on-flash-bbt;
+				nand-ecc-strength = <4>;
+				nand-ecc-step-size = <512>;
+
+				partition@0 {
+					label = "u-boot";
+					/* 1.0 MiB */
+					reg = <0x0000000 0x100000>;
+					read-only;
+				};
+
+				partition@100000 {
+					label = "u-boot-env";
+					/* 128 KiB */
+					reg = <0x100000 0x20000>;
+					read-only;
+				};
+
+				partition@120000 {
+					label = "uImage";
+					/* 7 MiB */
+					reg = <0x120000 0x700000>;
+				};
+
+				partition@820000 {
+					label = "ubifs";
+					/* ~ 84 MiB */
+					reg = <0x820000 0x54e0000>;
+				};
+
+				/* Hardcoded into stock bootloader */
+				partition@5d00000 {
+					label = "failsafe-uImage";
+					/* 5 MiB */
+					reg = <0x5d00000 0x500000>;
+				};
+
+				partition@6200000 {
+					label = "failsafe-fs";
+					/* 29 MiB */
+					reg = <0x6200000 0x1d00000>;
+				};
+
+				partition@7f00000 {
+					label = "bbt";
+					/* 1 MiB for BBT */
+					reg = <0x7f00000 0x100000>;
+				};
+			};
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <
+			&backup_button_pin
+			&power_button_pin
+			&reset_button_pin>;
+		pinctrl-names = "default";
+
+		power-button {
+			label = "Power Button";
+			linux,code = <KEY_POWER>;
+			gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+		};
+
+		backup-button {
+			label = "Backup Button";
+			linux,code = <KEY_COPY>;
+			gpios = <&gpio1 31 GPIO_ACTIVE_LOW>;
+		};
+
+		reset-button {
+			label = "Reset Button";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <
+			&sata_l_amber_pin
+			&sata_r_amber_pin
+			&backup_led_pin
+			/* Ensure these are managed by hardware */
+			&sata_l_white_pin
+			&sata_r_white_pin>;
+
+		pinctrl-names = "default";
+
+		sata-r-amber-pin {
+			label = "dns327l:amber:sata-r";
+			gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+		};
+
+		sata-l-amber-pin {
+			label = "dns327l:amber:sata-l";
+			gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+		};
+
+		backup-led-pin {
+			label = "dns327l:white:usb";
+			gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		usb_power: regulator@1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			pinctrl-0 = <&xhci_pwr_pin>;
+			pinctrl-names = "default";
+			regulator-name = "USB3.0 Port Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			regulator-boot-on;
+			regulator-always-on;
+			gpio = <&gpio0 13 GPIO_ACTIVE_HIGH>;
+		};
+
+		sata_r_power: regulator@2 {
+			compatible = "regulator-fixed";
+			reg = <2>;
+			pinctrl-0 = <&sata_r_pwr_pin>;
+			pinctrl-names = "default";
+			regulator-name = "SATA-R Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			startup-delay-us = <2000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
+		};
+
+		sata_l_power: regulator@3 {
+			compatible = "regulator-fixed";
+			reg = <3>;
+			pinctrl-0 = <&sata_l_pwr_pin>;
+			pinctrl-names = "default";
+			regulator-name = "SATA-L Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			startup-delay-us = <4000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio1 24 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&pinctrl {
+	sata_l_white_pin: sata-l-white-pin {
+		marvell,pins = "mpp57";
+		marvell,function = "sata0";
+	};
+
+	sata_r_white_pin: sata-r-white-pin {
+		marvell,pins = "mpp55";
+		marvell,function = "sata1";
+	};
+
+	sata_r_amber_pin: sata-r-amber-pin {
+		marvell,pins = "mpp52";
+		marvell,function = "gpio";
+	};
+
+	sata_l_amber_pin: sata-l-amber-pin {
+		marvell,pins = "mpp53";
+		marvell,function = "gpio";
+	};
+
+	backup_led_pin: backup-led-pin {
+		marvell,pins = "mpp61";
+		marvell,function = "gpo";
+	};
+
+	xhci_pwr_pin: xhci-pwr-pin {
+		marvell,pins = "mpp13";
+		marvell,function = "gpio";
+	};
+
+	sata_r_pwr_pin: sata-r-pwr-pin {
+		marvell,pins = "mpp54";
+		marvell,function = "gpio";
+	};
+
+	sata_l_pwr_pin: sata-l-pwr-pin {
+		marvell,pins = "mpp56";
+		marvell,function = "gpio";
+	};
+
+	uart1_pins: uart1-pins {
+		marvell,pins = "mpp60", "mpp61";
+		marvell,function = "uart1";
+	};
+
+	power_button_pin: power-button-pin {
+		marvell,pins = "mpp65";
+		marvell,function = "gpio";
+	};
+
+	backup_button_pin: backup-button-pin {
+		marvell,pins = "mpp63";
+		marvell,function = "gpio";
+	};
+
+	reset_button_pin: reset-button-pin {
+		marvell,pins = "mpp64";
+		marvell,function = "gpio";
+	};
+};
+
+/* Serial console */
+&uart0 {
+	status = "okay";
+};
+
+/* Connected to Weltrend MCU */
+&uart1 {
+	pinctrl-0 = <&uart1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&mdio {
+	phy0: ethernet-phy@0 { /* Marvell 88E1318 */
+		reg = <0>;
+		marvell,reg-init = <0x0 0x16 0x0 0x0002>,
+				<0x0 0x19 0x0 0x0077>,
+				<0x0 0x18 0x0 0x5747>;
+	};
+};
+
+&eth1 {
+	phy = <&phy0>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+};
+
+&i2c0 {
+	compatible = "marvell,mv64xxx-i2c";
+	clock-frequency = <100000>;
+	status = "okay";
+};