drm/panel: Add Sharp LQ101R1SX01 support

This panel requires dual-channel mode. The device accepts command-mode
data on 8 lanes and will therefore need a dual-channel DSI controller.
The two interfaces that make up this device need to be instantiated in
the controllers that gang up to provide the dual-channel DSI host.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>

Documentation/devicetree/bindings/panel/sharp,lq101r1sx01.txt

+Sharp Microelectronics 10.1" WQXGA TFT LCD panel
+
+This panel requires a dual-channel DSI host to operate. It supports two modes:
+- left-right: each channel drives the left or right half of the screen
+- even-odd: each channel drives the even or odd lines of the screen
+
+Each of the DSI channels controls a separate DSI peripheral. The peripheral
+driven by the first link (DSI-LINK1), left or even, is considered the primary
+peripheral and controls the device. The 'link2' property contains a phandle
+to the peripheral driven by the second link (DSI-LINK2, right or odd).
+
+Note that in video mode the DSI-LINK1 interface always provides the left/even
+pixels and DSI-LINK2 always provides the right/odd pixels. In command mode it
+is possible to program either link to drive the left/even or right/odd pixels
+but for the sake of consistency this binding assumes that the same assignment
+is chosen as for video mode.
+
+Required properties:
+- compatible: should be "sharp,lq101r1sx01"
+- reg: DSI virtual channel of the peripheral
+
+Required properties (for DSI-LINK1 only):
+- link2: phandle to the DSI peripheral on the secondary link. Note that the
+  presence of this property marks the containing node as DSI-LINK1.
+- power-supply: phandle of the regulator that provides the supply voltage
+
+Optional properties (for DSI-LINK1 only):
+- backlight: phandle of the backlight device attached to the panel
+
+Example:
+
+	dsi@54300000 {
+		panel: panel@0 {
+			compatible = "sharp,lq101r1sx01";
+			reg = <0>;
+
+			link2 = <&secondary>;
+
+			power-supply = <...>;
+			backlight = <...>;
+		};
+	};
+
+	dsi@54400000 {
+		secondary: panel@0 {
+			compatible = "sharp,lq101r1sx01";
+			reg = <0>;
+		};
+	};

drivers/gpu/drm/panel/Kconfig

@@ -27,4 +27,17 @@ config DRM_PANEL_S6E8AA0
 	select DRM_MIPI_DSI
 	select VIDEOMODE_HELPERS
 
+config DRM_PANEL_SHARP_LQ101R1SX01
+	tristate "Sharp LQ101R1SX01 panel"
+	depends on OF
+	depends on DRM_MIPI_DSI
+	help
+	  Say Y here if you want to enable support for Sharp LQ101R1SX01
+	  TFT-LCD modules. The panel has a 2560x1600 resolution and uses
+	  24 bit RGB per pixel. It provides a dual MIPI DSI interface to
+	  the host and has a built-in LED backlight.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called panel-sharp-lq101r1sx01.
+
 endmenu

drivers/gpu/drm/panel/Makefile

 obj-$(CONFIG_DRM_PANEL_SIMPLE) += panel-simple.o
 obj-$(CONFIG_DRM_PANEL_LD9040) += panel-ld9040.o
 obj-$(CONFIG_DRM_PANEL_S6E8AA0) += panel-s6e8aa0.o
+obj-$(CONFIG_DRM_PANEL_SHARP_LQ101R1SX01) += panel-sharp-lq101r1sx01.o