Skip to content

L
linux
Commit 1a66b851 authored by Arnd Bergmann's avatar Arnd Bergmann
Browse files
Options

Merge tag 'sunxi-dt-for-4.9-3' of... 

Merge tag 'sunxi-dt-for-4.9-3' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/late

Pull "Allwinner DT changes for 4.9, late edition" from Maxime Ripard:

Here is a bunch of late changes for the 4.9 merge window, mostly:
  - Added a bunch of touchscreens nodes to tablets
  - Added support for the AXP806 PMIC found in the A80 boards
  - Enabled a few pinmux options for the H3

* tag 'sunxi-dt-for-4.9-3' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
  ARM: dts: sun8i: Add accelerometer to polaroid-mid2407pxe03
  ARM: dts: sun8i: enable UART1 for iNet D978 Rev2 board
  ARM: dts: sun8i: add pinmux for UART1 at PG
  dts: sun8i-h3: add I2C0-2 peripherals to H3 SOC
  dts: sun8i-h3: add pinmux definitions for I2C0-2
  dts: sun8i-h3: associate exposed UARTs on Orange Pi Boards
  dts: sun8i-h3: split off RTS/CTS for UART1 in seperate pinmux
  dts: sun8i-h3: add pinmux definitions for UART2-3
  ARM: dts: sun9i: a80-optimus: Disable EHCI1
  ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and regulators
  ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators
  ARM: dts: sun9i: cubieboard4: Declare AXP809 SW regulator as unused
  ARM: dts: sun9i: a80-optimus: Declare AXP809 SW regulator as unused
  ARM: dts: sun8i: Add touchscreen node for sun8i-a33-ga10h
  ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2809pxe04
  ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2407pxe03
  ARM: dts: sun8i: Add touchscreen node for sun8i-a23-inet86dz
  ARM: dts: sun8i: Add touchscreen node for sun8i-a23-gt90h
parents c3a66272 90cb4b8c
Hide whitespace changes
Inline Side-by-side
Showing with 468 additions and 5 deletions
arch/arm/boot/dts/sun8i-a23-a33.dtsi
View file @ 1a66b851
......@@ -279,6 +279,16 @@ uart0_pins_a: uart0@0 {
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
uart1_pins_a: uart1@0 {
allwinner,pins = "PG6", "PG7";
allwinner,function = "uart1";
};
uart1_pins_cts_rts_a: uart1-cts-rts@0 {
allwinner,pins = "PG8", "PG9";
allwinner,function = "uart1";
};
mmc0_pins_a: mmc0@0 {
allwinner,pins = "PF0", "PF1", "PF2",
"PF3", "PF4", "PF5";
......
arch/arm/boot/dts/sun8i-a23-gt90h-v4.dts
View file @ 1a66b851
......@@ -53,6 +53,15 @@ &ehci0 {
status = "okay";
};
&touchscreen {
reg = <0x40>;
compatible = "silead,gsl3675";
firmware-name = "gsl3675-gt90h.fw";
touchscreen-size-x = <1792>;
touchscreen-size-y = <1024>;
status = "okay";
};
&lradc {
button@600 {
label = "Back";
......
arch/arm/boot/dts/sun8i-a23-inet86dz.dts
View file @ 1a66b851
......@@ -53,6 +53,15 @@ &ehci0 {
status = "okay";
};
&touchscreen {
reg = <0x40>;
compatible = "silead,gsl1680";
firmware-name = "gsl1680-inet86dz.fw";
touchscreen-size-x = <960>;
touchscreen-size-y = <640>;
status = "okay";
};
&usbphy {
usb1_vbus-supply = <&reg_dldo1>;
};
arch/arm/boot/dts/sun8i-a23-polaroid-mid2407pxe03.dts
View file @ 1a66b851
......@@ -62,6 +62,13 @@ wifi_pwrseq: wifi_pwrseq {
};
};
&i2c1 {
mma7660: accelerometer@4c {
reg = <0x4c>;
compatible = "fsl,mma7660";
};
};
&mmc1 {
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins_a>;
......@@ -90,3 +97,22 @@ wifi_pwrseq_pin_mid2407: wifi_pwrseq_pin@0 {
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
};
&reg_ldo_io1 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-touchscreen";
status = "okay";
};
&touchscreen {
reg = <0x40>;
compatible = "silead,gsl1680";
firmware-name = "gsl1680-polaroid-mid2407pxe03.fw";
touchscreen-size-x = <960>;
touchscreen-size-y = <640>;
touchscreen-inverted-x;
touchscreen-inverted-y;
vddio-supply = <&reg_ldo_io1>;
status = "okay";
};
arch/arm/boot/dts/sun8i-a23-polaroid-mid2809pxe04.dts
View file @ 1a66b851
......@@ -90,3 +90,12 @@ wifi_pwrseq_pin_mid2809: wifi_pwrseq_pin@0 {
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
};
&touchscreen {
reg = <0x40>;
compatible = "silead,gsl3670";
firmware-name = "gsl3670-polaroid-mid2809pxe04.fw";
touchscreen-size-x = <1660>;
touchscreen-size-y = <890>;
status = "okay";
};
arch/arm/boot/dts/sun8i-a33-ga10h-v1.1.dts
View file @ 1a66b851
......@@ -58,6 +58,16 @@ &ehci0 {
status = "okay";
};
&touchscreen {
reg = <0x40>;
compatible = "silead,gsl3675";
firmware-name = "gsl3675-ga10h.fw";
touchscreen-size-x = <1630>;
touchscreen-size-y = <990>;
touchscreen-inverted-y;
status = "okay";
};
&lradc {
button@600 {
label = "Back";
......
arch/arm/boot/dts/sun8i-a33-inet-d978-rev2.dts
View file @ 1a66b851
......@@ -49,6 +49,15 @@ / {
model = "INet-D978 Rev 02";
compatible = "primux,inet-d978-rev2", "allwinner,sun8i-a33";
aliases {
serial0 = &uart1;
};
chosen {
/* Delete debug UART as serial0 is the UART for bluetooth */
/delete-property/stdout-path;
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
......@@ -86,3 +95,14 @@ led_pin_d978: led_pin_d978@0 {
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
};
&r_uart {
status = "disabled";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_pins_a>,
<&uart1_pins_cts_rts_a>;
status = "okay";
};
arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts
View file @ 1a66b851
......@@ -185,7 +185,7 @@ &uart0 {
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_pins_a>;
pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
status = "okay";
};
......
arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
View file @ 1a66b851
......@@ -186,6 +186,24 @@ &uart0 {
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_pins>;
status = "disabled";
};
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&uart2_pins>;
status = "disabled";
};
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&uart3_pins>;
status = "disabled";
};
&usb1_vbus_pin_a {
allwinner,pins = "PG13";
};
......
arch/arm/boot/dts/sun8i-h3-orangepi-one.dts
View file @ 1a66b851
......@@ -139,6 +139,24 @@ &uart0 {
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_pins>;
status = "disabled";
};
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&uart2_pins>;
status = "disabled";
};
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&uart3_pins>;
status = "disabled";
};
&usbphy {
/* USB VBUS is always on */
status = "okay";
......
arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts
View file @ 1a66b851
......@@ -161,6 +161,24 @@ &uart0 {
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_pins>;
status = "disabled";
};
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&uart2_pins>;
status = "disabled";
};
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&uart3_pins>;
status = "disabled";
};
&usbphy {
/* USB VBUS is always on */
status = "okay";
......
arch/arm/boot/dts/sun8i-h3.dtsi
View file @ 1a66b851
......@@ -327,6 +327,27 @@ pio: pinctrl@01c20800 {
interrupt-controller;
#interrupt-cells = <3>;
i2c0_pins: i2c0 {
allwinner,pins = "PA11", "PA12";
allwinner,function = "i2c0";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
i2c1_pins: i2c1 {
allwinner,pins = "PA18", "PA19";
allwinner,function = "i2c1";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
i2c2_pins: i2c2 {
allwinner,pins = "PE12", "PE13";
allwinner,function = "i2c2";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
mmc0_pins_a: mmc0@0 {
allwinner,pins = "PF0", "PF1", "PF2", "PF3",
"PF4", "PF5";
......@@ -367,12 +388,33 @@ uart0_pins_a: uart0@0 {
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
uart1_pins_a: uart1@0 {
allwinner,pins = "PG6", "PG7", "PG8", "PG9";
uart1_pins: uart1 {
allwinner,pins = "PG6", "PG7";
allwinner,function = "uart1";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
uart1_rts_cts_pins: uart1_rts_cts {
allwinner,pins = "PG8", "PG9";
allwinner,function = "uart1";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
uart2_pins: uart2 {
allwinner,pins = "PA0", "PA1";
allwinner,function = "uart2";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
uart3_pins: uart3 {
allwinner,pins = "PG13", "PG14";
allwinner,function = "uart3";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
};
timer@01c20c00 {
......@@ -449,6 +491,45 @@ uart3: serial@01c28c00 {
status = "disabled";
};
i2c0: i2c@01c2ac00 {
compatible = "allwinner,sun6i-a31-i2c";
reg = <0x01c2ac00 0x400>;
interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_I2C0>;
resets = <&ccu RST_BUS_I2C0>;
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
i2c1: i2c@01c2b000 {
compatible = "allwinner,sun6i-a31-i2c";
reg = <0x01c2b000 0x400>;
interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_I2C1>;
resets = <&ccu RST_BUS_I2C1>;
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
i2c2: i2c@01c2b400 {
compatible = "allwinner,sun6i-a31-i2c";
reg = <0x01c2b000 0x400>;
interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_I2C2>;
resets = <&ccu RST_BUS_I2C2>;
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
gic: interrupt-controller@01c81000 {
compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
reg = <0x01c81000 0x1000>,
......
arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
View file @ 1a66b851
......@@ -253,6 +253,122 @@ reg_ldo_io1: ldo_io1 {
reg_rtc_ldo: rtc_ldo {
regulator-name = "vcc-rtc-vdd1v8-io";
};
sw {
/* unused */
};
};
};
axp806: pmic@745 {
compatible = "x-powers,axp806";
reg = <0x745>;
interrupt-parent = <&nmi_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
interrupt-controller;
#interrupt-cells = <1>;
bldoin-supply = <&reg_dcdce>;
regulators {
reg_s_aldo1: aldo1 {
regulator-always-on;
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-name = "avcc";
};
aldo2 {
/*
* unused, but use a different name to
* avoid name clash with axp809's aldo's
*/
regulator-name = "s_aldo2";
};
aldo3 {
/*
* unused, but use a different name to
* avoid name clash with axp809's aldo's
*/
regulator-name = "s_aldo3";
};
reg_bldo1: bldo1 {
regulator-always-on;
regulator-min-microvolt = <1700000>;
regulator-max-microvolt = <1900000>;
regulator-name = "vcc18-efuse-adc-display-csi";
};
reg_bldo2: bldo2 {
regulator-always-on;
regulator-min-microvolt = <1700000>;
regulator-max-microvolt = <1900000>;
regulator-name =
"vdd18-drampll-vcc18-pll-cpvdd";
};
bldo3 {
/* unused */
};
reg_bldo4: bldo4 {
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1300000>;
regulator-name = "vcc12-hsic";
};
reg_cldo1: cldo1 {
/*
* This was 3V in the original design, but
* 3.3V is the recommended supply voltage
* for the Ethernet PHY.
*/
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-gmac-phy";
};
reg_cldo2: cldo2 {
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
regulator-name = "afvcc-cam";
};
reg_cldo3: cldo3 {
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-name = "vcc-io-wifi-codec-io2";
};
reg_dcdca: dcdca {
regulator-always-on;
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <1100000>;
regulator-name = "vdd-cpub";
};
reg_dcdcd: dcdcd {
regulator-always-on;
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <1100000>;
regulator-name = "vdd-vpu";
};
reg_dcdce: dcdce {
regulator-always-on;
regulator-min-microvolt = <2100000>;
regulator-max-microvolt = <2100000>;
regulator-name = "vcc-bldo-codec-ldoin";
};
sw {
/*
* unused, but use a different name to
* avoid name clash with axp809's sw
*/
regulator-name = "s_sw";
};
};
};
......
arch/arm/boot/dts/sun9i-a80-optimus.dts
View file @ 1a66b851
......@@ -112,7 +112,8 @@ &ehci0 {
};
&ehci1 {
status = "okay";
/* Enable if HSIC peripheral is connected */
status = "disabled";
};
&ehci2 {
......@@ -325,6 +326,122 @@ reg_ldo_io1: ldo_io1 {
reg_rtc_ldo: rtc_ldo {
regulator-name = "vcc-rtc-vdd1v8-io";
};
sw {
/* unused */
};
};
};
axp806: pmic@745 {
compatible = "x-powers,axp806";
reg = <0x745>;
interrupt-parent = <&nmi_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
interrupt-controller;
#interrupt-cells = <1>;
bldoin-supply = <&reg_dcdce>;
regulators {
reg_s_aldo1: aldo1 {
regulator-always-on;
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-name = "avcc";
};
aldo2 {
/*
* unused, but use a different name to
* avoid name clash with axp809's aldo's
*/
regulator-name = "s_aldo2";
};
aldo3 {
/*
* unused, but use a different name to
* avoid name clash with axp809's aldo's
*/
regulator-name = "s_aldo3";
};
reg_bldo1: bldo1 {
regulator-always-on;
regulator-min-microvolt = <1700000>;
regulator-max-microvolt = <1900000>;
regulator-name = "vcc18-efuse-adc-display-csi";
};
reg_bldo2: bldo2 {
regulator-always-on;
regulator-min-microvolt = <1700000>;
regulator-max-microvolt = <1900000>;
regulator-name =
"vdd18-drampll-vcc18-pll-cpvdd";
};
bldo3 {
/* unused */
};
reg_bldo4: bldo4 {
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1300000>;
regulator-name = "vcc12-hsic";
};
reg_cldo1: cldo1 {
/*
* This was 3V in the original design, but
* 3.3V is the recommended supply voltage
* for the Ethernet PHY.
*/
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-gmac-phy";
};
reg_cldo2: cldo2 {
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
regulator-name = "afvcc-cam";
};
reg_cldo3: cldo3 {
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-name = "vcc-io-wifi-codec-io2";
};
reg_dcdca: dcdca {
regulator-always-on;
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <1100000>;
regulator-name = "vdd-cpub";
};
reg_dcdcd: dcdcd {
regulator-always-on;
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <1100000>;
regulator-name = "vdd-vpu";
};
reg_dcdce: dcdce {
regulator-always-on;
regulator-min-microvolt = <2100000>;
regulator-max-microvolt = <2100000>;
regulator-name = "vcc-bldo-codec-ldoin";
};
sw {
/*
* unused, but use a different name to
* avoid name clash with axp809's sw
*/
regulator-name = "s_sw";
};
};
};
......@@ -367,7 +484,9 @@ &usbphy1 {
};
&usbphy2 {
status = "okay";
phy-supply = <&reg_bldo4>;
/* Enable if HSIC peripheral is connected */
status = "disabled";
};
&usbphy3 {
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7