Commit 1ddfe82d authored by Florian Fainelli's avatar Florian Fainelli Committed by Ralf Baechle

[MIPS] RB532: Do not define registers that are already defined

Use the register definitions of the MPMC controller from
mach-rc32434/rb.h instead of redefining them.
Signed-off-by: default avatarFlorian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: default avatarRalf Baechle <ralf@linux-mips.org>
parent a571444a
...@@ -49,8 +49,6 @@ ...@@ -49,8 +49,6 @@
#define GPIO_ALE (1 << 0x0a) #define GPIO_ALE (1 << 0x0a)
#define GPIO_CLE (1 << 0x0b) #define GPIO_CLE (1 << 0x0b)
extern char *board_type;
static struct resource korina_dev0_res[] = { static struct resource korina_dev0_res[] = {
{ {
.name = "korina_regs", .name = "korina_regs",
...@@ -265,14 +263,6 @@ static void __init parse_mac_addr(char *macstr) ...@@ -265,14 +263,6 @@ static void __init parse_mac_addr(char *macstr)
} }
/* DEVICE CONTROLLER 1 */
#define CFG_DC_DEV1 ((void *)0xb8010010)
#define CFG_DC_DEV2 ((void *)0xb8010020)
#define CFG_DC_DEVBASE 0x0
#define CFG_DC_DEVMASK 0x4
#define CFG_DC_DEVC 0x8
#define CFG_DC_DEVTC 0xC
/* NAND definitions */ /* NAND definitions */
#define NAND_CHIP_DELAY 25 #define NAND_CHIP_DELAY 25
...@@ -301,16 +291,16 @@ static void __init rb532_nand_setup(void) ...@@ -301,16 +291,16 @@ static void __init rb532_nand_setup(void)
static int __init plat_setup_devices(void) static int __init plat_setup_devices(void)
{ {
/* Look for the CF card reader */ /* Look for the CF card reader */
if (!readl(CFG_DC_DEV1 + CFG_DC_DEVMASK)) if (!readl(IDT434_REG_BASE + DEV1MASK))
rb532_devs[1] = NULL; rb532_devs[1] = NULL;
else { else {
cf_slot0_res[0].start = cf_slot0_res[0].start =
readl(CFG_DC_DEV1 + CFG_DC_DEVBASE); readl(IDT434_REG_BASE + DEV1BASE);
cf_slot0_res[0].end = cf_slot0_res[0].start + 0x1000; cf_slot0_res[0].end = cf_slot0_res[0].start + 0x1000;
} }
/* Read the NAND resources from the device controller */ /* Read the NAND resources from the device controller */
nand_slot0_res[0].start = readl(CFG_DC_DEV2 + CFG_DC_DEVBASE); nand_slot0_res[0].start = readl(IDT434_REG_BASE + DEV2BASE);
nand_slot0_res[0].end = nand_slot0_res[0].start + 0x1000; nand_slot0_res[0].end = nand_slot0_res[0].start + 0x1000;
/* Initialise the NAND device */ /* Initialise the NAND device */
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment