Commit 1e724845 authored by David Brownell's avatar David Brownell Committed by Greg Kroah-Hartman

[PATCH] remove duplication from Documentation/power/devices.txt

Remove a chunk of duplicated documentation text.
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@suse.de>
parent 4039483f
...@@ -118,96 +118,6 @@ will fail. ...@@ -118,96 +118,6 @@ will fail.
There is currently no way to know what states a device or driver There is currently no way to know what states a device or driver
supports a priori. This will change in the future. supports a priori. This will change in the future.
pm_message_t meaning
pm_message_t has two fields. event ("major"), and flags. If driver
does not know event code, it aborts the request, returning error. Some
drivers may need to deal with special cases based on the actual type
of suspend operation being done at the system level. This is why
there are flags.
Event codes are:
ON -- no need to do anything except special cases like broken
HW.
# NOTIFICATION -- pretty much same as ON?
FREEZE -- stop DMA and interrupts, and be prepared to reinit HW from
scratch. That probably means stop accepting upstream requests, the
actual policy of what to do with them beeing specific to a given
driver. It's acceptable for a network driver to just drop packets
while a block driver is expected to block the queue so no request is
lost. (Use IDE as an example on how to do that). FREEZE requires no
power state change, and it's expected for drivers to be able to
quickly transition back to operating state.
SUSPEND -- like FREEZE, but also put hardware into low-power state. If
there's need to distinguish several levels of sleep, additional flag
is probably best way to do that.
Transitions are only from a resumed state to a suspended state, never
between 2 suspended states. (ON -> FREEZE or ON -> SUSPEND can happen,
FREEZE -> SUSPEND or SUSPEND -> FREEZE can not).
All events are:
[NOTE NOTE NOTE: If you are driver author, you should not care; you
should only look at event, and ignore flags.]
#Prepare for suspend -- userland is still running but we are going to
#enter suspend state. This gives drivers chance to load firmware from
#disk and store it in memory, or do other activities taht require
#operating userland, ability to kmalloc GFP_KERNEL, etc... All of these
#are forbiden once the suspend dance is started.. event = ON, flags =
#PREPARE_TO_SUSPEND
Apm standby -- prepare for APM event. Quiesce devices to make life
easier for APM BIOS. event = FREEZE, flags = APM_STANDBY
Apm suspend -- same as APM_STANDBY, but it we should probably avoid
spinning down disks. event = FREEZE, flags = APM_SUSPEND
System halt, reboot -- quiesce devices to make life easier for BIOS. event
= FREEZE, flags = SYSTEM_HALT or SYSTEM_REBOOT
System shutdown -- at least disks need to be spun down, or data may be
lost. Quiesce devices, just to make life easier for BIOS. event =
FREEZE, flags = SYSTEM_SHUTDOWN
Kexec -- turn off DMAs and put hardware into some state where new
kernel can take over. event = FREEZE, flags = KEXEC
Powerdown at end of swsusp -- very similar to SYSTEM_SHUTDOWN, except wake
may need to be enabled on some devices. This actually has at least 3
subtypes, system can reboot, enter S4 and enter S5 at the end of
swsusp. event = FREEZE, flags = SWSUSP and one of SYSTEM_REBOOT,
SYSTEM_SHUTDOWN, SYSTEM_S4
Suspend to ram -- put devices into low power state. event = SUSPEND,
flags = SUSPEND_TO_RAM
Freeze for swsusp snapshot -- stop DMA and interrupts. No need to put
devices into low power mode, but you must be able to reinitialize
device from scratch in resume method. This has two flavors, its done
once on suspending kernel, once on resuming kernel. event = FREEZE,
flags = DURING_SUSPEND or DURING_RESUME
Device detach requested from /sys -- deinitialize device; proably same as
SYSTEM_SHUTDOWN, I do not understand this one too much. probably event
= FREEZE, flags = DEV_DETACH.
#These are not really events sent:
#
#System fully on -- device is working normally; this is probably never
#passed to suspend() method... event = ON, flags = 0
#
#Ready after resume -- userland is now running, again. Time to free any
#memory you ate during prepare to suspend... event = ON, flags =
#READY_AFTER_RESUME
#
pm_message_t meaning pm_message_t meaning
pm_message_t has two fields. event ("major"), and flags. If driver pm_message_t has two fields. event ("major"), and flags. If driver
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment