Commit 1ead6581 authored by Linus Torvalds's avatar Linus Torvalds

Merge branch 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull timer changes from Thomas Gleixner:
 "This assorted collection provides:

   - A new timer based timer broadcast feature for systems which do not
     provide a global accessible timer device.  That allows those
     systems to put CPUs into deep idle states where the per cpu timer
     device stops.

   - A few NOHZ_FULL related improvements to the timer wheel

   - The usual updates to timer devices found in ARM SoCs

   - Small improvements and updates all over the place"

* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (44 commits)
  tick: Remove code duplication in tick_handle_periodic()
  tick: Fix spelling mistake in tick_handle_periodic()
  x86: hpet: Use proper destructor for delayed work
  workqueue: Provide destroy_delayed_work_on_stack()
  clocksource: CMT, MTU2, TMU and STI should depend on GENERIC_CLOCKEVENTS
  timer: Remove code redundancy while calling get_nohz_timer_target()
  hrtimer: Rearrange comments in the order struct members are declared
  timer: Use variable head instead of &work_list in __run_timers()
  clocksource: exynos_mct: silence a static checker warning
  arm: zynq: Add support for cpufreq
  arm: zynq: Don't use arm_global_timer with cpufreq
  clocksource/cadence_ttc: Overhaul clocksource frequency adjustment
  clocksource/cadence_ttc: Call clockevents_update_freq() with IRQs enabled
  clocksource: Add Kconfig entries for CMT, MTU2, TMU and STI
  sh: Remove Kconfig entries for TMU, CMT and MTU2
  ARM: shmobile: Remove CMT, TMU and STI Kconfig entries
  clocksource: armada-370-xp: Use atomic access for shared registers
  clocksource: orion: Use atomic access for shared registers
  clocksource: timer-keystone: Delete unnecessary variable
  clocksource: timer-keystone: introduce clocksource driver for Keystone
  ...
parents b6d739e9 b97f0291
......@@ -2,7 +2,7 @@ Allwinner A1X SoCs Timer Controller
Required properties:
- compatible : should be "allwinner,sun4i-timer"
- compatible : should be "allwinner,sun4i-a10-timer"
- reg : Specifies base physical address and size of the registers.
- interrupts : The interrupt of the first timer
- clocks: phandle to the source clock (usually a 24 MHz fixed clock)
......@@ -10,7 +10,7 @@ Required properties:
Example:
timer {
compatible = "allwinner,sun4i-timer";
compatible = "allwinner,sun4i-a10-timer";
reg = <0x01c20c00 0x400>;
interrupts = <22>;
clocks = <&osc>;
......
* Device tree bindings for Texas instruments Keystone timer
This document provides bindings for the 64-bit timer in the KeyStone
architecture devices. The timer can be configured as a general-purpose 64-bit
timer, dual general-purpose 32-bit timers. When configured as dual 32-bit
timers, each half can operate in conjunction (chain mode) or independently
(unchained mode) of each other.
It is global timer is a free running up-counter and can generate interrupt
when the counter reaches preset counter values.
Documentation:
http://www.ti.com/lit/ug/sprugv5a/sprugv5a.pdf
Required properties:
- compatible : should be "ti,keystone-timer".
- reg : specifies base physical address and count of the registers.
- interrupts : interrupt generated by the timer.
- clocks : the clock feeding the timer clock.
Example:
timer@22f0000 {
compatible = "ti,keystone-timer";
reg = <0x022f0000 0x80>;
interrupts = <GIC_SPI 110 IRQ_TYPE_EDGE_RISING>;
clocks = <&clktimer15>;
};
......@@ -1320,6 +1320,7 @@ M: Linus Walleij <linus.walleij@linaro.org>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
S: Supported
F: arch/arm/mach-u300/
F: drivers/clocksource/timer-u300.c
F: drivers/i2c/busses/i2c-stu300.c
F: drivers/rtc/rtc-coh901331.c
F: drivers/watchdog/coh901327_wdt.c
......
......@@ -403,7 +403,7 @@ emac_pins_a: emac0@0 {
};
timer@01c20c00 {
compatible = "allwinner,sun4i-timer";
compatible = "allwinner,sun4i-a10-timer";
reg = <0x01c20c00 0x90>;
interrupts = <22>;
clocks = <&osc24M>;
......
......@@ -366,7 +366,7 @@ i2c2_pins_a: i2c2@0 {
};
timer@01c20c00 {
compatible = "allwinner,sun4i-timer";
compatible = "allwinner,sun4i-a10-timer";
reg = <0x01c20c00 0x90>;
interrupts = <22>;
clocks = <&osc24M>;
......
......@@ -329,7 +329,7 @@ i2c2_pins_a: i2c2@0 {
};
timer@01c20c00 {
compatible = "allwinner,sun4i-timer";
compatible = "allwinner,sun4i-a10-timer";
reg = <0x01c20c00 0x90>;
interrupts = <22>;
clocks = <&osc24M>;
......
......@@ -231,7 +231,7 @@ apb2_rst: reset@01c202d8 {
};
timer@01c20c00 {
compatible = "allwinner,sun4i-timer";
compatible = "allwinner,sun4i-a10-timer";
reg = <0x01c20c00 0xa0>;
interrupts = <0 18 4>,
<0 19 4>,
......
......@@ -435,7 +435,7 @@ clk_out_b_pins_a: clk_out_b@0 {
};
timer@01c20c00 {
compatible = "allwinner,sun4i-timer";
compatible = "allwinner,sun4i-a10-timer";
reg = <0x01c20c00 0x90>;
interrupts = <0 22 4>,
<0 23 4>,
......
......@@ -24,6 +24,12 @@ cpu@0 {
device_type = "cpu";
reg = <0>;
clocks = <&clkc 3>;
operating-points = <
/* kHz uV */
666667 1000000
333334 1000000
222223 1000000
>;
};
cpu@1 {
......
......@@ -24,17 +24,21 @@ comment "Renesas ARM SoCs System Type"
config ARCH_EMEV2
bool "Emma Mobile EV2"
select SYS_SUPPORTS_EM_STI
config ARCH_R7S72100
bool "RZ/A1H (R7S72100)"
select SYS_SUPPORTS_SH_MTU2
config ARCH_R8A7790
bool "R-Car H2 (R8A77900)"
select RENESAS_IRQC
select SYS_SUPPORTS_SH_CMT
config ARCH_R8A7791
bool "R-Car M2 (R8A77910)"
select RENESAS_IRQC
select SYS_SUPPORTS_SH_CMT
comment "Renesas ARM SoCs Board Type"
......@@ -68,6 +72,8 @@ config ARCH_SH7372
select ARM_CPU_SUSPEND if PM || CPU_IDLE
select CPU_V7
select SH_CLK_CPG
select SYS_SUPPORTS_SH_CMT
select SYS_SUPPORTS_SH_TMU
config ARCH_SH73A0
bool "SH-Mobile AG5 (R8A73A00)"
......@@ -77,6 +83,8 @@ config ARCH_SH73A0
select I2C
select SH_CLK_CPG
select RENESAS_INTC_IRQPIN
select SYS_SUPPORTS_SH_CMT
select SYS_SUPPORTS_SH_TMU
config ARCH_R8A73A4
bool "R-Mobile APE6 (R8A73A40)"
......@@ -87,6 +95,8 @@ config ARCH_R8A73A4
select RENESAS_IRQC
select ARCH_HAS_CPUFREQ
select ARCH_HAS_OPP
select SYS_SUPPORTS_SH_CMT
select SYS_SUPPORTS_SH_TMU
config ARCH_R8A7740
bool "R-Mobile A1 (R8A77400)"
......@@ -95,6 +105,8 @@ config ARCH_R8A7740
select CPU_V7
select SH_CLK_CPG
select RENESAS_INTC_IRQPIN
select SYS_SUPPORTS_SH_CMT
select SYS_SUPPORTS_SH_TMU
config ARCH_R8A7778
bool "R-Car M1A (R8A77781)"
......@@ -104,6 +116,7 @@ config ARCH_R8A7778
select ARM_GIC
select USB_ARCH_HAS_EHCI
select USB_ARCH_HAS_OHCI
select SYS_SUPPORTS_SH_TMU
config ARCH_R8A7779
bool "R-Car H1 (R8A77790)"
......@@ -114,6 +127,7 @@ config ARCH_R8A7779
select USB_ARCH_HAS_EHCI
select USB_ARCH_HAS_OHCI
select RENESAS_INTC_IRQPIN
select SYS_SUPPORTS_SH_TMU
config ARCH_R8A7790
bool "R-Car H2 (R8A77900)"
......@@ -123,6 +137,7 @@ config ARCH_R8A7790
select MIGHT_HAVE_PCI
select SH_CLK_CPG
select RENESAS_IRQC
select SYS_SUPPORTS_SH_CMT
config ARCH_R8A7791
bool "R-Car M2 (R8A77910)"
......@@ -132,6 +147,7 @@ config ARCH_R8A7791
select MIGHT_HAVE_PCI
select SH_CLK_CPG
select RENESAS_IRQC
select SYS_SUPPORTS_SH_CMT
config ARCH_EMEV2
bool "Emma Mobile EV2"
......@@ -141,6 +157,7 @@ config ARCH_EMEV2
select MIGHT_HAVE_PCI
select USE_OF
select AUTO_ZRELADDR
select SYS_SUPPORTS_EM_STI
config ARCH_R7S72100
bool "RZ/A1H (R7S72100)"
......@@ -148,6 +165,7 @@ config ARCH_R7S72100
select ARM_GIC
select CPU_V7
select SH_CLK_CPG
select SYS_SUPPORTS_SH_MTU2
comment "Renesas ARM SoCs Board Type"
......@@ -321,24 +339,6 @@ config SHMOBILE_TIMER_HZ
want to select a HZ value such as 128 that can evenly divide RCLK.
A HZ value that does not divide evenly may cause timer drift.
config SH_TIMER_CMT
bool "CMT timer driver"
default y
help
This enables build of the CMT timer driver.
config SH_TIMER_TMU
bool "TMU timer driver"
default y
help
This enables build of the TMU timer driver.
config EM_TIMER_STI
bool "STI timer driver"
default y
help
This enables build of the STI timer driver.
endmenu
endif
......@@ -2,7 +2,7 @@
# Makefile for the linux kernel, U300 machine.
#
obj-y := core.o timer.o
obj-y := core.o
obj-m :=
obj-n :=
obj- :=
......
......@@ -2,6 +2,8 @@ config ARCH_ZYNQ
bool "Xilinx Zynq ARM Cortex A9 Platform" if ARCH_MULTI_V7
select ARM_AMBA
select ARM_GIC
select ARCH_HAS_CPUFREQ
select ARCH_HAS_OPP
select COMMON_CLK
select CPU_V7
select GENERIC_CLOCKEVENTS
......@@ -13,6 +15,6 @@ config ARCH_ZYNQ
select HAVE_SMP
select SPARSE_IRQ
select CADENCE_TTC_TIMER
select ARM_GLOBAL_TIMER
select ARM_GLOBAL_TIMER if !CPU_FREQ
help
Support for Xilinx Zynq ARM Cortex A9 Platform
......@@ -64,6 +64,8 @@ static struct platform_device zynq_cpuidle_device = {
*/
static void __init zynq_init_machine(void)
{
struct platform_device_info devinfo = { .name = "cpufreq-cpu0", };
/*
* 64KB way size, 8-way associativity, parity disabled
*/
......@@ -72,6 +74,7 @@ static void __init zynq_init_machine(void)
of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
platform_device_register(&zynq_cpuidle_device);
platform_device_register_full(&devinfo);
}
static void __init zynq_timer_init(void)
......
......@@ -123,15 +123,6 @@ config SYS_SUPPORTS_NUMA
config SYS_SUPPORTS_PCI
bool
config SYS_SUPPORTS_CMT
bool
config SYS_SUPPORTS_MTU2
bool
config SYS_SUPPORTS_TMU
bool
config STACKTRACE_SUPPORT
def_bool y
......@@ -191,14 +182,14 @@ config CPU_SH3
bool
select CPU_HAS_INTEVT
select CPU_HAS_SR_RB
select SYS_SUPPORTS_TMU
select SYS_SUPPORTS_SH_TMU
config CPU_SH4
bool
select CPU_HAS_INTEVT
select CPU_HAS_SR_RB
select CPU_HAS_FPU if !CPU_SH4AL_DSP
select SYS_SUPPORTS_TMU
select SYS_SUPPORTS_SH_TMU
select SYS_SUPPORTS_HUGETLBFS if MMU
config CPU_SH4A
......@@ -213,7 +204,7 @@ config CPU_SH4AL_DSP
config CPU_SH5
bool
select CPU_HAS_FPU
select SYS_SUPPORTS_TMU
select SYS_SUPPORTS_SH_TMU
select SYS_SUPPORTS_HUGETLBFS if MMU
config CPU_SHX2
......@@ -250,7 +241,7 @@ choice
config CPU_SUBTYPE_SH7619
bool "Support SH7619 processor"
select CPU_SH2
select SYS_SUPPORTS_CMT
select SYS_SUPPORTS_SH_CMT
# SH-2A Processor Support
......@@ -258,50 +249,50 @@ config CPU_SUBTYPE_SH7201
bool "Support SH7201 processor"
select CPU_SH2A
select CPU_HAS_FPU
select SYS_SUPPORTS_MTU2
select SYS_SUPPORTS_SH_MTU2
config CPU_SUBTYPE_SH7203
bool "Support SH7203 processor"
select CPU_SH2A
select CPU_HAS_FPU
select SYS_SUPPORTS_CMT
select SYS_SUPPORTS_MTU2
select SYS_SUPPORTS_SH_CMT
select SYS_SUPPORTS_SH_MTU2
select ARCH_WANT_OPTIONAL_GPIOLIB
select PINCTRL
config CPU_SUBTYPE_SH7206
bool "Support SH7206 processor"
select CPU_SH2A
select SYS_SUPPORTS_CMT
select SYS_SUPPORTS_MTU2
select SYS_SUPPORTS_SH_CMT
select SYS_SUPPORTS_SH_MTU2
config CPU_SUBTYPE_SH7263
bool "Support SH7263 processor"
select CPU_SH2A
select CPU_HAS_FPU
select SYS_SUPPORTS_CMT
select SYS_SUPPORTS_MTU2
select SYS_SUPPORTS_SH_CMT
select SYS_SUPPORTS_SH_MTU2
config CPU_SUBTYPE_SH7264
bool "Support SH7264 processor"
select CPU_SH2A
select CPU_HAS_FPU
select SYS_SUPPORTS_CMT
select SYS_SUPPORTS_MTU2
select SYS_SUPPORTS_SH_CMT
select SYS_SUPPORTS_SH_MTU2
select PINCTRL
config CPU_SUBTYPE_SH7269
bool "Support SH7269 processor"
select CPU_SH2A
select CPU_HAS_FPU
select SYS_SUPPORTS_CMT
select SYS_SUPPORTS_MTU2
select SYS_SUPPORTS_SH_CMT
select SYS_SUPPORTS_SH_MTU2
select PINCTRL
config CPU_SUBTYPE_MXG
bool "Support MX-G processor"
select CPU_SH2A
select SYS_SUPPORTS_MTU2
select SYS_SUPPORTS_SH_MTU2
help
Select MX-G if running on an R8A03022BG part.
......@@ -354,7 +345,7 @@ config CPU_SUBTYPE_SH7720
bool "Support SH7720 processor"
select CPU_SH3
select CPU_HAS_DSP
select SYS_SUPPORTS_CMT
select SYS_SUPPORTS_SH_CMT
select ARCH_WANT_OPTIONAL_GPIOLIB
select USB_ARCH_HAS_OHCI
select USB_OHCI_SH if USB_OHCI_HCD
......@@ -366,7 +357,7 @@ config CPU_SUBTYPE_SH7721
bool "Support SH7721 processor"
select CPU_SH3
select CPU_HAS_DSP
select SYS_SUPPORTS_CMT
select SYS_SUPPORTS_SH_CMT
select USB_ARCH_HAS_OHCI
select USB_OHCI_SH if USB_OHCI_HCD
help
......@@ -422,7 +413,7 @@ config CPU_SUBTYPE_SH7723
select CPU_SHX2
select ARCH_SHMOBILE
select ARCH_SPARSEMEM_ENABLE
select SYS_SUPPORTS_CMT
select SYS_SUPPORTS_SH_CMT
select ARCH_WANT_OPTIONAL_GPIOLIB
select PINCTRL
help
......@@ -434,7 +425,7 @@ config CPU_SUBTYPE_SH7724
select CPU_SHX2
select ARCH_SHMOBILE
select ARCH_SPARSEMEM_ENABLE
select SYS_SUPPORTS_CMT
select SYS_SUPPORTS_SH_CMT
select ARCH_WANT_OPTIONAL_GPIOLIB
select PINCTRL
help
......@@ -514,7 +505,7 @@ config CPU_SUBTYPE_SH7343
bool "Support SH7343 processor"
select CPU_SH4AL_DSP
select ARCH_SHMOBILE
select SYS_SUPPORTS_CMT
select SYS_SUPPORTS_SH_CMT
config CPU_SUBTYPE_SH7722
bool "Support SH7722 processor"
......@@ -523,7 +514,7 @@ config CPU_SUBTYPE_SH7722
select ARCH_SHMOBILE
select ARCH_SPARSEMEM_ENABLE
select SYS_SUPPORTS_NUMA
select SYS_SUPPORTS_CMT
select SYS_SUPPORTS_SH_CMT
select ARCH_WANT_OPTIONAL_GPIOLIB
select PINCTRL
......@@ -534,7 +525,7 @@ config CPU_SUBTYPE_SH7366
select ARCH_SHMOBILE
select ARCH_SPARSEMEM_ENABLE
select SYS_SUPPORTS_NUMA
select SYS_SUPPORTS_CMT
select SYS_SUPPORTS_SH_CMT
endchoice
......@@ -567,27 +558,6 @@ source "arch/sh/boards/Kconfig"
menu "Timer and clock configuration"
config SH_TIMER_TMU
bool "TMU timer driver"
depends on SYS_SUPPORTS_TMU
default y
help
This enables the build of the TMU timer driver.
config SH_TIMER_CMT
bool "CMT timer driver"
depends on SYS_SUPPORTS_CMT
default y
help
This enables build of the CMT timer driver.
config SH_TIMER_MTU2
bool "MTU2 timer driver"
depends on SYS_SUPPORTS_MTU2
default y
help
This enables build of the MTU2 timer driver.
config SH_PCLK_FREQ
int "Peripheral clock frequency (in Hz)"
depends on SH_CLK_CPG_LEGACY
......
......@@ -699,7 +699,7 @@ static int hpet_cpuhp_notify(struct notifier_block *n,
/* FIXME: add schedule_work_on() */
schedule_delayed_work_on(cpu, &work.work, 0);
wait_for_completion(&work.complete);
destroy_timer_on_stack(&work.work.timer);
destroy_delayed_work_on_stack(&work.work);
break;
case CPU_DEAD:
if (hdev) {
......
......@@ -140,3 +140,51 @@ config VF_PIT_TIMER
bool
help
Support for Period Interrupt Timer on Freescale Vybrid Family SoCs.
config SYS_SUPPORTS_SH_CMT
bool
config SYS_SUPPORTS_SH_MTU2
bool
config SYS_SUPPORTS_SH_TMU
bool
config SYS_SUPPORTS_EM_STI
bool
config SH_TIMER_CMT
bool "Renesas CMT timer driver" if COMPILE_TEST
depends on GENERIC_CLOCKEVENTS
default SYS_SUPPORTS_SH_CMT
help
This enables build of a clocksource and clockevent driver for
the Compare Match Timer (CMT) hardware available in 16/32/48-bit
variants on a wide range of Mobile and Automotive SoCs from Renesas.
config SH_TIMER_MTU2
bool "Renesas MTU2 timer driver" if COMPILE_TEST
depends on GENERIC_CLOCKEVENTS
default SYS_SUPPORTS_SH_MTU2
help
This enables build of a clockevent driver for the Multi-Function
Timer Pulse Unit 2 (TMU2) hardware available on SoCs from Renesas.
This hardware comes with 16 bit-timer registers.
config SH_TIMER_TMU
bool "Renesas TMU timer driver" if COMPILE_TEST
depends on GENERIC_CLOCKEVENTS
default SYS_SUPPORTS_SH_TMU
help
This enables build of a clocksource and clockevent driver for
the 32-bit Timer Unit (TMU) hardware available on a wide range
SoCs from Renesas.
config EM_TIMER_STI
bool "Renesas STI timer driver" if COMPILE_TEST
depends on GENERIC_CLOCKEVENTS
default SYS_SUPPORTS_EM_STI
help
This enables build of a clocksource and clockevent driver for
the 48-bit System Timer (STI) hardware available on a SoCs
such as EMEV2 from former NEC Electronics.
......@@ -21,6 +21,7 @@ obj-$(CONFIG_ARCH_MARCO) += timer-marco.o
obj-$(CONFIG_ARCH_MOXART) += moxart_timer.o
obj-$(CONFIG_ARCH_MXS) += mxs_timer.o
obj-$(CONFIG_ARCH_PRIMA2) += timer-prima2.o
obj-$(CONFIG_ARCH_U300) += timer-u300.o
obj-$(CONFIG_SUN4I_TIMER) += sun4i_timer.o
obj-$(CONFIG_SUN5I_HSTIMER) += timer-sun5i.o
obj-$(CONFIG_ARCH_TEGRA) += tegra20_timer.o
......@@ -37,3 +38,4 @@ obj-$(CONFIG_ARM_ARCH_TIMER) += arm_arch_timer.o
obj-$(CONFIG_ARM_GLOBAL_TIMER) += arm_global_timer.o
obj-$(CONFIG_CLKSRC_METAG_GENERIC) += metag_generic.o
obj-$(CONFIG_ARCH_HAS_TICK_BROADCAST) += dummy_timer.o
obj-$(CONFIG_ARCH_KEYSTONE) += timer-keystone.o
......@@ -277,6 +277,7 @@ static void __arch_timer_setup(unsigned type,
clk->set_next_event = arch_timer_set_next_event_phys;
}
} else {
clk->features |= CLOCK_EVT_FEAT_DYNIRQ;
clk->name = "arch_mem_timer";
clk->rating = 400;
clk->cpumask = cpu_all_mask;
......
......@@ -16,6 +16,7 @@
*/
#include <linux/clk.h>
#include <linux/clk-provider.h>
#include <linux/interrupt.h>
#include <linux/clockchips.h>
#include <linux/of_address.h>
......@@ -52,6 +53,8 @@
#define TTC_CNT_CNTRL_DISABLE_MASK 0x1
#define TTC_CLK_CNTRL_CSRC_MASK (1 << 5) /* clock source */
#define TTC_CLK_CNTRL_PSV_MASK 0x1e
#define TTC_CLK_CNTRL_PSV_SHIFT 1
/*
* Setup the timers to use pre-scaling, using a fixed value for now that will
......@@ -63,6 +66,8 @@
#define CLK_CNTRL_PRESCALE_EN 1
#define CNT_CNTRL_RESET (1 << 4)
#define MAX_F_ERR 50
/**
* struct ttc_timer - This definition defines local timer structure
*
......@@ -82,6 +87,8 @@ struct ttc_timer {
container_of(x, struct ttc_timer, clk_rate_change_nb)
struct ttc_timer_clocksource {
u32 scale_clk_ctrl_reg_old;
u32 scale_clk_ctrl_reg_new;
struct ttc_timer ttc;
struct clocksource cs;
};
......@@ -229,32 +236,89 @@ static int ttc_rate_change_clocksource_cb(struct notifier_block *nb,
struct ttc_timer_clocksource, ttc);
switch (event) {
case POST_RATE_CHANGE:
case PRE_RATE_CHANGE:
{
u32 psv;
unsigned long factor, rate_low, rate_high;
if (ndata->new_rate > ndata->old_rate) {
factor = DIV_ROUND_CLOSEST(ndata->new_rate,
ndata->old_rate);
rate_low = ndata->old_rate;
rate_high = ndata->new_rate;
} else {
factor = DIV_ROUND_CLOSEST(ndata->old_rate,
ndata->new_rate);
rate_low = ndata->new_rate;
rate_high = ndata->old_rate;
}
if (!is_power_of_2(factor))
return NOTIFY_BAD;
if (abs(rate_high - (factor * rate_low)) > MAX_F_ERR)
return NOTIFY_BAD;
factor = __ilog2_u32(factor);
/*
* Do whatever is necessary to maintain a proper time base
*
* I cannot find a way to adjust the currently used clocksource
* to the new frequency. __clocksource_updatefreq_hz() sounds
* good, but does not work. Not sure what's that missing.
*
* This approach works, but triggers two clocksource switches.
* The first after unregister to clocksource jiffies. And
* another one after the register to the newly registered timer.
*
* Alternatively we could 'waste' another HW timer to ping pong
* between clock sources. That would also use one register and
* one unregister call, but only trigger one clocksource switch
* for the cost of another HW timer used by the OS.
* store timer clock ctrl register so we can restore it in case
* of an abort.
*/
clocksource_unregister(&ttccs->cs);
clocksource_register_hz(&ttccs->cs,
ndata->new_rate / PRESCALE);
/* fall through */
case PRE_RATE_CHANGE:
ttccs->scale_clk_ctrl_reg_old =
__raw_readl(ttccs->ttc.base_addr +
TTC_CLK_CNTRL_OFFSET);
psv = (ttccs->scale_clk_ctrl_reg_old &
TTC_CLK_CNTRL_PSV_MASK) >>
TTC_CLK_CNTRL_PSV_SHIFT;
if (ndata->new_rate < ndata->old_rate)
psv -= factor;
else
psv += factor;
/* prescaler within legal range? */
if (psv & ~(TTC_CLK_CNTRL_PSV_MASK >> TTC_CLK_CNTRL_PSV_SHIFT))
return NOTIFY_BAD;
ttccs->scale_clk_ctrl_reg_new = ttccs->scale_clk_ctrl_reg_old &
~TTC_CLK_CNTRL_PSV_MASK;
ttccs->scale_clk_ctrl_reg_new |= psv << TTC_CLK_CNTRL_PSV_SHIFT;
/* scale down: adjust divider in post-change notification */
if (ndata->new_rate < ndata->old_rate)
return NOTIFY_DONE;
/* scale up: adjust divider now - before frequency change */
__raw_writel(ttccs->scale_clk_ctrl_reg_new,
ttccs->ttc.base_addr + TTC_CLK_CNTRL_OFFSET);
break;
}
case POST_RATE_CHANGE:
/* scale up: pre-change notification did the adjustment */
if (ndata->new_rate > ndata->old_rate)
return NOTIFY_OK;
/* scale down: adjust divider now - after frequency change */
__raw_writel(ttccs->scale_clk_ctrl_reg_new,
ttccs->ttc.base_addr + TTC_CLK_CNTRL_OFFSET);
break;
case ABORT_RATE_CHANGE:
/* we have to undo the adjustment in case we scale up */
if (ndata->new_rate < ndata->old_rate)
return NOTIFY_OK;
/* restore original register value */
__raw_writel(ttccs->scale_clk_ctrl_reg_old,
ttccs->ttc.base_addr + TTC_CLK_CNTRL_OFFSET);
/* fall through */
default:
return NOTIFY_DONE;
}
return NOTIFY_DONE;
}
static void __init ttc_setup_clocksource(struct clk *clk, void __iomem *base)
......@@ -321,25 +385,12 @@ static int ttc_rate_change_clockevent_cb(struct notifier_block *nb,
switch (event) {
case POST_RATE_CHANGE:
{
unsigned long flags;
/*
* clockevents_update_freq should be called with IRQ disabled on
* the CPU the timer provides events for. The timer we use is
* common to both CPUs, not sure if we need to run on both
* cores.
*/
local_irq_save(flags);
clockevents_update_freq(&ttcce->ce,
ndata->new_rate / PRESCALE);
local_irq_restore(flags);
/* update cached frequency */
ttc->freq = ndata->new_rate;
clockevents_update_freq(&ttcce->ce, ndata->new_rate / PRESCALE);
/* fall through */
}
case PRE_RATE_CHANGE:
case ABORT_RATE_CHANGE:
default:
......
......@@ -410,7 +410,7 @@ static int exynos4_local_timer_setup(struct clock_event_device *evt)
mevt = container_of(evt, struct mct_clock_event_device, evt);
mevt->base = EXYNOS4_MCT_L_BASE(cpu);
sprintf(mevt->name, "mct_tick%d", cpu);
snprintf(mevt->name, sizeof(mevt->name), "mct_tick%d", cpu);
evt->name = mevt->name;
evt->cpumask = cpumask_of(cpu);
......
......@@ -196,5 +196,5 @@ static void __init sun4i_timer_init(struct device_node *node)
clockevents_config_and_register(&sun4i_clockevent, rate,
TIMER_SYNC_TICKS, 0xffffffff);
}
CLOCKSOURCE_OF_DECLARE(sun4i, "allwinner,sun4i-timer",
CLOCKSOURCE_OF_DECLARE(sun4i, "allwinner,sun4i-a10-timer",
sun4i_timer_init);
......@@ -85,12 +85,6 @@ static u32 ticks_per_jiffy;
static struct clock_event_device __percpu *armada_370_xp_evt;
static void timer_ctrl_clrset(u32 clr, u32 set)
{
writel((readl(timer_base + TIMER_CTRL_OFF) & ~clr) | set,
timer_base + TIMER_CTRL_OFF);
}
static void local_timer_ctrl_clrset(u32 clr, u32 set)
{
writel((readl(local_base + TIMER_CTRL_OFF) & ~clr) | set,
......@@ -245,7 +239,7 @@ static void __init armada_370_xp_timer_common_init(struct device_node *np)
clr = TIMER0_25MHZ;
enable_mask = TIMER0_EN | TIMER0_DIV(TIMER_DIVIDER_SHIFT);
}
timer_ctrl_clrset(clr, set);
atomic_io_modify(timer_base + TIMER_CTRL_OFF, clr | set, set);
local_timer_ctrl_clrset(clr, set);
/*
......@@ -263,7 +257,9 @@ static void __init armada_370_xp_timer_common_init(struct device_node *np)
writel(0xffffffff, timer_base + TIMER0_VAL_OFF);
writel(0xffffffff, timer_base + TIMER0_RELOAD_OFF);
timer_ctrl_clrset(0, TIMER0_RELOAD_EN | enable_mask);
atomic_io_modify(timer_base + TIMER_CTRL_OFF,
TIMER0_RELOAD_EN | enable_mask,
TIMER0_RELOAD_EN | enable_mask);
/*
* Set scale and timer for sched_clock.
......
......@@ -35,20 +35,6 @@
#define ORION_ONESHOT_MAX 0xfffffffe
static void __iomem *timer_base;
static DEFINE_SPINLOCK(timer_ctrl_lock);
/*
* Thread-safe access to TIMER_CTRL register
* (shared with watchdog timer)
*/
void orion_timer_ctrl_clrset(u32 clr, u32 set)
{
spin_lock(&timer_ctrl_lock);
writel((readl(timer_base + TIMER_CTRL) & ~clr) | set,
timer_base + TIMER_CTRL);
spin_unlock(&timer_ctrl_lock);
}
EXPORT_SYMBOL(orion_timer_ctrl_clrset);
/*
* Free-running clocksource handling.
......@@ -68,7 +54,8 @@ static int orion_clkevt_next_event(unsigned long delta,
{
/* setup and enable one-shot timer */
writel(delta, timer_base + TIMER1_VAL);
orion_timer_ctrl_clrset(TIMER1_RELOAD_EN, TIMER1_EN);
atomic_io_modify(timer_base + TIMER_CTRL,
TIMER1_RELOAD_EN | TIMER1_EN, TIMER1_EN);
return 0;
}
......@@ -80,10 +67,13 @@ static void orion_clkevt_mode(enum clock_event_mode mode,
/* setup and enable periodic timer at 1/HZ intervals */
writel(ticks_per_jiffy - 1, timer_base + TIMER1_RELOAD);
writel(ticks_per_jiffy - 1, timer_base + TIMER1_VAL);
orion_timer_ctrl_clrset(0, TIMER1_RELOAD_EN | TIMER1_EN);
atomic_io_modify(timer_base + TIMER_CTRL,
TIMER1_RELOAD_EN | TIMER1_EN,
TIMER1_RELOAD_EN | TIMER1_EN);
} else {
/* disable timer */
orion_timer_ctrl_clrset(TIMER1_RELOAD_EN | TIMER1_EN, 0);
atomic_io_modify(timer_base + TIMER_CTRL,
TIMER1_RELOAD_EN | TIMER1_EN, 0);
}
}
......@@ -131,7 +121,9 @@ static void __init orion_timer_init(struct device_node *np)
/* setup timer0 as free-running clocksource */
writel(~0, timer_base + TIMER0_VAL);
writel(~0, timer_base + TIMER0_RELOAD);
orion_timer_ctrl_clrset(0, TIMER0_RELOAD_EN | TIMER0_EN);
atomic_io_modify(timer_base + TIMER_CTRL,
TIMER0_RELOAD_EN | TIMER0_EN,
TIMER0_RELOAD_EN | TIMER0_EN);
clocksource_mmio_init(timer_base + TIMER0_VAL, "orion_clocksource",
clk_get_rate(clk), 300, 32,
clocksource_mmio_readl_down);
......
/*
* Keystone broadcast clock-event
*
* Copyright 2013 Texas Instruments, Inc.
*
* Author: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
*/
#include <linux/clk.h>
#include <linux/clockchips.h>
#include <linux/clocksource.h>
#include <linux/interrupt.h>
#include <linux/of_address.h>
#include <linux/of_irq.h>
#define TIMER_NAME "timer-keystone"
/* Timer register offsets */
#define TIM12 0x10
#define TIM34 0x14
#define PRD12 0x18
#define PRD34 0x1c
#define TCR 0x20
#define TGCR 0x24
#define INTCTLSTAT 0x44
/* Timer register bitfields */
#define TCR_ENAMODE_MASK 0xC0
#define TCR_ENAMODE_ONESHOT_MASK 0x40
#define TCR_ENAMODE_PERIODIC_MASK 0x80
#define TGCR_TIM_UNRESET_MASK 0x03
#define INTCTLSTAT_ENINT_MASK 0x01
/**
* struct keystone_timer: holds timer's data
* @base: timer memory base address
* @hz_period: cycles per HZ period
* @event_dev: event device based on timer
*/
static struct keystone_timer {
void __iomem *base;
unsigned long hz_period;
struct clock_event_device event_dev;
} timer;
static inline u32 keystone_timer_readl(unsigned long rg)
{
return readl_relaxed(timer.base + rg);
}
static inline void keystone_timer_writel(u32 val, unsigned long rg)
{
writel_relaxed(val, timer.base + rg);
}
/**
* keystone_timer_barrier: write memory barrier
* use explicit barrier to avoid using readl/writel non relaxed function
* variants, because in our case non relaxed variants hide the true places
* where barrier is needed.
*/
static inline void keystone_timer_barrier(void)
{
__iowmb();
}
/**
* keystone_timer_config: configures timer to work in oneshot/periodic modes.
* @ mode: mode to configure
* @ period: cycles number to configure for
*/
static int keystone_timer_config(u64 period, enum clock_event_mode mode)
{
u32 tcr;
u32 off;
tcr = keystone_timer_readl(TCR);
off = tcr & ~(TCR_ENAMODE_MASK);
/* set enable mode */
switch (mode) {
case CLOCK_EVT_MODE_ONESHOT:
tcr |= TCR_ENAMODE_ONESHOT_MASK;
break;
case CLOCK_EVT_MODE_PERIODIC:
tcr |= TCR_ENAMODE_PERIODIC_MASK;
break;
default:
return -1;
}
/* disable timer */
keystone_timer_writel(off, TCR);
/* here we have to be sure the timer has been disabled */
keystone_timer_barrier();
/* reset counter to zero, set new period */
keystone_timer_writel(0, TIM12);
keystone_timer_writel(0, TIM34);
keystone_timer_writel(period & 0xffffffff, PRD12);
keystone_timer_writel(period >> 32, PRD34);
/*
* enable timer
* here we have to be sure that CNTLO, CNTHI, PRDLO, PRDHI registers
* have been written.
*/
keystone_timer_barrier();
keystone_timer_writel(tcr, TCR);
return 0;
}
static void keystone_timer_disable(void)
{
u32 tcr;
tcr = keystone_timer_readl(TCR);
/* disable timer */
tcr &= ~(TCR_ENAMODE_MASK);
keystone_timer_writel(tcr, TCR);
}
static irqreturn_t keystone_timer_interrupt(int irq, void *dev_id)
{
struct clock_event_device *evt = dev_id;
evt->event_handler(evt);
return IRQ_HANDLED;
}
static int keystone_set_next_event(unsigned long cycles,
struct clock_event_device *evt)
{
return keystone_timer_config(cycles, evt->mode);
}
static void keystone_set_mode(enum clock_event_mode mode,
struct clock_event_device *evt)
{
switch (mode) {
case CLOCK_EVT_MODE_PERIODIC:
keystone_timer_config(timer.hz_period, CLOCK_EVT_MODE_PERIODIC);
break;
case CLOCK_EVT_MODE_UNUSED:
case CLOCK_EVT_MODE_SHUTDOWN:
case CLOCK_EVT_MODE_ONESHOT:
keystone_timer_disable();
break;
default:
break;
}
}
static void __init keystone_timer_init(struct device_node *np)
{
struct clock_event_device *event_dev = &timer.event_dev;
unsigned long rate;
struct clk *clk;
int irq, error;
irq = irq_of_parse_and_map(np, 0);
if (irq == NO_IRQ) {
pr_err("%s: failed to map interrupts\n", __func__);
return;
}
timer.base = of_iomap(np, 0);
if (!timer.base) {
pr_err("%s: failed to map registers\n", __func__);
return;
}
clk = of_clk_get(np, 0);
if (IS_ERR(clk)) {
pr_err("%s: failed to get clock\n", __func__);
iounmap(timer.base);
return;
}
error = clk_prepare_enable(clk);
if (error) {
pr_err("%s: failed to enable clock\n", __func__);
goto err;
}
rate = clk_get_rate(clk);
/* disable, use internal clock source */
keystone_timer_writel(0, TCR);
/* here we have to be sure the timer has been disabled */
keystone_timer_barrier();
/* reset timer as 64-bit, no pre-scaler, plus features are disabled */
keystone_timer_writel(0, TGCR);
/* unreset timer */
keystone_timer_writel(TGCR_TIM_UNRESET_MASK, TGCR);
/* init counter to zero */
keystone_timer_writel(0, TIM12);
keystone_timer_writel(0, TIM34);
timer.hz_period = DIV_ROUND_UP(rate, HZ);
/* enable timer interrupts */
keystone_timer_writel(INTCTLSTAT_ENINT_MASK, INTCTLSTAT);
error = request_irq(irq, keystone_timer_interrupt, IRQF_TIMER,
TIMER_NAME, event_dev);
if (error) {
pr_err("%s: failed to setup irq\n", __func__);
goto err;
}
/* setup clockevent */
event_dev->features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT;
event_dev->set_next_event = keystone_set_next_event;
event_dev->set_mode = keystone_set_mode;
event_dev->cpumask = cpu_all_mask;
event_dev->owner = THIS_MODULE;
event_dev->name = TIMER_NAME;
event_dev->irq = irq;
clockevents_config_and_register(event_dev, rate, 1, ULONG_MAX);
pr_info("keystone timer clock @%lu Hz\n", rate);
return;
err:
clk_put(clk);
iounmap(timer.base);
}
CLOCKSOURCE_OF_DECLARE(keystone_timer, "ti,keystone-timer",
keystone_timer_init);
/*
*
* arch/arm/mach-u300/timer.c
*
*
* Copyright (C) 2007-2009 ST-Ericsson AB
* License terms: GNU General Public License (GPL) version 2
* Timer COH 901 328, runs the OS timer interrupt.
......
......@@ -140,12 +140,14 @@ int cpuidle_idle_call(void)
return 0;
}
trace_cpu_idle_rcuidle(next_state, dev->cpu);
broadcast = !!(drv->states[next_state].flags & CPUIDLE_FLAG_TIMER_STOP);
if (broadcast)
clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_ENTER, &dev->cpu);
if (broadcast &&
clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_ENTER, &dev->cpu))
return -EBUSY;
trace_cpu_idle_rcuidle(next_state, dev->cpu);
if (cpuidle_state_is_coupled(dev, drv, next_state))
entered_state = cpuidle_enter_state_coupled(dev, drv,
......@@ -153,11 +155,11 @@ int cpuidle_idle_call(void)
else
entered_state = cpuidle_enter_state(dev, drv, next_state);
trace_cpu_idle_rcuidle(PWR_EVENT_EXIT, dev->cpu);
if (broadcast)
clockevents_notify(CLOCK_EVT_NOTIFY_BROADCAST_EXIT, &dev->cpu);
trace_cpu_idle_rcuidle(PWR_EVENT_EXIT, dev->cpu);
/* give the governor an opportunity to reflect on the outcome */
if (cpuidle_curr_governor->reflect)
cpuidle_curr_governor->reflect(dev, entered_state);
......
......@@ -317,6 +317,7 @@ SYSCALL_DEFINE2(timerfd_create, int, clockid, int, flags)
(clockid != CLOCK_MONOTONIC &&
clockid != CLOCK_REALTIME &&
clockid != CLOCK_REALTIME_ALARM &&
clockid != CLOCK_BOOTTIME &&
clockid != CLOCK_BOOTTIME_ALARM))
return -EINVAL;
......
......@@ -62,6 +62,11 @@ enum clock_event_mode {
#define CLOCK_EVT_FEAT_DYNIRQ 0x000020
#define CLOCK_EVT_FEAT_PERCPU 0x000040
/*
* Clockevent device is based on a hrtimer for broadcast
*/
#define CLOCK_EVT_FEAT_HRTIMER 0x000080
/**
* struct clock_event_device - clock event device descriptor
* @event_handler: Assigned by the framework to be called by the low
......@@ -83,6 +88,7 @@ enum clock_event_mode {
* @name: ptr to clock event name
* @rating: variable to rate clock event devices
* @irq: IRQ number (only for non CPU local devices)
* @bound_on: Bound on CPU
* @cpumask: cpumask to indicate for which CPUs this device works
* @list: list head for the management code
* @owner: module reference
......@@ -113,6 +119,7 @@ struct clock_event_device {
const char *name;
int rating;
int irq;
int bound_on;
const struct cpumask *cpumask;
struct list_head list;
struct module *owner;
......@@ -180,15 +187,17 @@ extern int tick_receive_broadcast(void);
#endif
#if defined(CONFIG_GENERIC_CLOCKEVENTS_BROADCAST) && defined(CONFIG_TICK_ONESHOT)
extern void tick_setup_hrtimer_broadcast(void);
extern int tick_check_broadcast_expired(void);
#else
static inline int tick_check_broadcast_expired(void) { return 0; }
static inline void tick_setup_hrtimer_broadcast(void) {};
#endif
#ifdef CONFIG_GENERIC_CLOCKEVENTS
extern void clockevents_notify(unsigned long reason, void *arg);
extern int clockevents_notify(unsigned long reason, void *arg);
#else
static inline void clockevents_notify(unsigned long reason, void *arg) {}
static inline int clockevents_notify(unsigned long reason, void *arg) { return 0; }
#endif
#else /* CONFIG_GENERIC_CLOCKEVENTS_BUILD */
......@@ -196,8 +205,9 @@ static inline void clockevents_notify(unsigned long reason, void *arg) {}
static inline void clockevents_suspend(void) {}
static inline void clockevents_resume(void) {}
static inline void clockevents_notify(unsigned long reason, void *arg) {}
static inline int clockevents_notify(unsigned long reason, void *arg) { return 0; }
static inline int tick_check_broadcast_expired(void) { return 0; }
static inline void tick_setup_hrtimer_broadcast(void) {};
#endif
......
......@@ -96,12 +96,12 @@ enum hrtimer_restart {
* @function: timer expiry callback function
* @base: pointer to the timer base (per cpu and per clock)
* @state: state information (See bit values above)
* @start_pid: timer statistics field to store the pid of the task which
* started the timer
* @start_site: timer statistics field to store the site where the timer
* was started
* @start_comm: timer statistics field to store the name of the process which
* started the timer
* @start_pid: timer statistics field to store the pid of the task which
* started the timer
*
* The hrtimer structure must be initialized by hrtimer_init()
*/
......
......@@ -294,10 +294,14 @@ extern int runqueue_is_locked(int cpu);
#if defined(CONFIG_SMP) && defined(CONFIG_NO_HZ_COMMON)
extern void nohz_balance_enter_idle(int cpu);
extern void set_cpu_sd_state_idle(void);
extern int get_nohz_timer_target(void);
extern int get_nohz_timer_target(int pinned);
#else
static inline void nohz_balance_enter_idle(int cpu) { }
static inline void set_cpu_sd_state_idle(void) { }
static inline int get_nohz_timer_target(int pinned)
{
return smp_processor_id();
}
#endif
/*
......
......@@ -180,6 +180,7 @@ struct execute_work {
#ifdef CONFIG_DEBUG_OBJECTS_WORK
extern void __init_work(struct work_struct *work, int onstack);
extern void destroy_work_on_stack(struct work_struct *work);
extern void destroy_delayed_work_on_stack(struct delayed_work *work);
static inline unsigned int work_static(struct work_struct *work)
{
return *work_data_bits(work) & WORK_STRUCT_STATIC;
......@@ -187,6 +188,7 @@ static inline unsigned int work_static(struct work_struct *work)
#else
static inline void __init_work(struct work_struct *work, int onstack) { }
static inline void destroy_work_on_stack(struct work_struct *work) { }
static inline void destroy_delayed_work_on_stack(struct delayed_work *work) { }
static inline unsigned int work_static(struct work_struct *work) { return 0; }
#endif
......
......@@ -168,19 +168,6 @@ struct hrtimer_clock_base *lock_hrtimer_base(const struct hrtimer *timer,
}
}
/*
* Get the preferred target CPU for NOHZ
*/
static int hrtimer_get_target(int this_cpu, int pinned)
{
#ifdef CONFIG_NO_HZ_COMMON
if (!pinned && get_sysctl_timer_migration() && idle_cpu(this_cpu))
return get_nohz_timer_target();
#endif
return this_cpu;
}
/*
* With HIGHRES=y we do not migrate the timer when it is expiring
* before the next event on the target cpu because we cannot reprogram
......@@ -214,7 +201,7 @@ switch_hrtimer_base(struct hrtimer *timer, struct hrtimer_clock_base *base,
struct hrtimer_clock_base *new_base;
struct hrtimer_cpu_base *new_cpu_base;
int this_cpu = smp_processor_id();
int cpu = hrtimer_get_target(this_cpu, pinned);
int cpu = get_nohz_timer_target(pinned);
int basenum = base->index;
again:
......
......@@ -555,12 +555,15 @@ void resched_cpu(int cpu)
* selecting an idle cpu will add more delays to the timers than intended
* (as that cpu's timer base may not be uptodate wrt jiffies etc).
*/
int get_nohz_timer_target(void)
int get_nohz_timer_target(int pinned)
{
int cpu = smp_processor_id();
int i;
struct sched_domain *sd;
if (pinned || !get_sysctl_timer_migration() || !idle_cpu(cpu))
return cpu;
rcu_read_lock();
for_each_domain(cpu, sd) {
for_each_cpu(i, sched_domain_span(sd)) {
......
......@@ -124,7 +124,7 @@ config NO_HZ_FULL
endchoice
config NO_HZ_FULL_ALL
bool "Full dynticks system on all CPUs by default"
bool "Full dynticks system on all CPUs by default (except CPU 0)"
depends on NO_HZ_FULL
help
If the user doesn't pass the nohz_full boot option to
......
......@@ -3,7 +3,10 @@ obj-y += timeconv.o posix-clock.o alarmtimer.o
obj-$(CONFIG_GENERIC_CLOCKEVENTS_BUILD) += clockevents.o
obj-$(CONFIG_GENERIC_CLOCKEVENTS) += tick-common.o
obj-$(CONFIG_GENERIC_CLOCKEVENTS_BROADCAST) += tick-broadcast.o
ifeq ($(CONFIG_GENERIC_CLOCKEVENTS_BROADCAST),y)
obj-y += tick-broadcast.o
obj-$(CONFIG_TICK_ONESHOT) += tick-broadcast-hrtimer.o
endif
obj-$(CONFIG_GENERIC_SCHED_CLOCK) += sched_clock.o
obj-$(CONFIG_TICK_ONESHOT) += tick-oneshot.o
obj-$(CONFIG_TICK_ONESHOT) += tick-sched.o
......
......@@ -439,6 +439,19 @@ void clockevents_config_and_register(struct clock_event_device *dev,
}
EXPORT_SYMBOL_GPL(clockevents_config_and_register);
int __clockevents_update_freq(struct clock_event_device *dev, u32 freq)
{
clockevents_config(dev, freq);
if (dev->mode == CLOCK_EVT_MODE_ONESHOT)
return clockevents_program_event(dev, dev->next_event, false);
if (dev->mode == CLOCK_EVT_MODE_PERIODIC)
dev->set_mode(CLOCK_EVT_MODE_PERIODIC, dev);
return 0;
}
/**
* clockevents_update_freq - Update frequency and reprogram a clock event device.
* @dev: device to modify
......@@ -446,17 +459,22 @@ EXPORT_SYMBOL_GPL(clockevents_config_and_register);
*
* Reconfigure and reprogram a clock event device in oneshot
* mode. Must be called on the cpu for which the device delivers per
* cpu timer events with interrupts disabled! Returns 0 on success,
* -ETIME when the event is in the past.
* cpu timer events. If called for the broadcast device the core takes
* care of serialization.
*
* Returns 0 on success, -ETIME when the event is in the past.
*/
int clockevents_update_freq(struct clock_event_device *dev, u32 freq)
{
clockevents_config(dev, freq);
if (dev->mode != CLOCK_EVT_MODE_ONESHOT)
return 0;
unsigned long flags;
int ret;
return clockevents_program_event(dev, dev->next_event, false);
local_irq_save(flags);
ret = tick_broadcast_update_freq(dev, freq);
if (ret == -ENODEV)
ret = __clockevents_update_freq(dev, freq);
local_irq_restore(flags);
return ret;
}
/*
......@@ -524,12 +542,13 @@ void clockevents_resume(void)
#ifdef CONFIG_GENERIC_CLOCKEVENTS
/**
* clockevents_notify - notification about relevant events
* Returns 0 on success, any other value on error
*/
void clockevents_notify(unsigned long reason, void *arg)
int clockevents_notify(unsigned long reason, void *arg)
{
struct clock_event_device *dev, *tmp;
unsigned long flags;
int cpu;
int cpu, ret = 0;
raw_spin_lock_irqsave(&clockevents_lock, flags);
......@@ -542,7 +561,7 @@ void clockevents_notify(unsigned long reason, void *arg)
case CLOCK_EVT_NOTIFY_BROADCAST_ENTER:
case CLOCK_EVT_NOTIFY_BROADCAST_EXIT:
tick_broadcast_oneshot_control(reason);
ret = tick_broadcast_oneshot_control(reason);
break;
case CLOCK_EVT_NOTIFY_CPU_DYING:
......@@ -585,6 +604,7 @@ void clockevents_notify(unsigned long reason, void *arg)
break;
}
raw_spin_unlock_irqrestore(&clockevents_lock, flags);
return ret;
}
EXPORT_SYMBOL_GPL(clockevents_notify);
......
......@@ -514,12 +514,13 @@ static void sync_cmos_clock(struct work_struct *work)
next.tv_sec++;
next.tv_nsec -= NSEC_PER_SEC;
}
schedule_delayed_work(&sync_cmos_work, timespec_to_jiffies(&next));
queue_delayed_work(system_power_efficient_wq,
&sync_cmos_work, timespec_to_jiffies(&next));
}
void ntp_notify_cmos_timer(void)
{
schedule_delayed_work(&sync_cmos_work, 0);
queue_delayed_work(system_power_efficient_wq, &sync_cmos_work, 0);
}
#else
......
/*
* linux/kernel/time/tick-broadcast-hrtimer.c
* This file emulates a local clock event device
* via a pseudo clock device.
*/
#include <linux/cpu.h>
#include <linux/err.h>
#include <linux/hrtimer.h>
#include <linux/interrupt.h>
#include <linux/percpu.h>
#include <linux/profile.h>
#include <linux/clockchips.h>
#include <linux/sched.h>
#include <linux/smp.h>
#include <linux/module.h>
#include "tick-internal.h"
static struct hrtimer bctimer;
static void bc_set_mode(enum clock_event_mode mode,
struct clock_event_device *bc)
{
switch (mode) {
case CLOCK_EVT_MODE_SHUTDOWN:
/*
* Note, we cannot cancel the timer here as we might
* run into the following live lock scenario:
*
* cpu 0 cpu1
* lock(broadcast_lock);
* hrtimer_interrupt()
* bc_handler()
* tick_handle_oneshot_broadcast();
* lock(broadcast_lock);
* hrtimer_cancel()
* wait_for_callback()
*/
hrtimer_try_to_cancel(&bctimer);
break;
default:
break;
}
}
/*
* This is called from the guts of the broadcast code when the cpu
* which is about to enter idle has the earliest broadcast timer event.
*/
static int bc_set_next(ktime_t expires, struct clock_event_device *bc)
{
/*
* We try to cancel the timer first. If the callback is on
* flight on some other cpu then we let it handle it. If we
* were able to cancel the timer nothing can rearm it as we
* own broadcast_lock.
*
* However we can also be called from the event handler of
* ce_broadcast_hrtimer itself when it expires. We cannot
* restart the timer because we are in the callback, but we
* can set the expiry time and let the callback return
* HRTIMER_RESTART.
*/
if (hrtimer_try_to_cancel(&bctimer) >= 0) {
hrtimer_start(&bctimer, expires, HRTIMER_MODE_ABS_PINNED);
/* Bind the "device" to the cpu */
bc->bound_on = smp_processor_id();
} else if (bc->bound_on == smp_processor_id()) {
hrtimer_set_expires(&bctimer, expires);
}
return 0;
}
static struct clock_event_device ce_broadcast_hrtimer = {
.set_mode = bc_set_mode,
.set_next_ktime = bc_set_next,
.features = CLOCK_EVT_FEAT_ONESHOT |
CLOCK_EVT_FEAT_KTIME |
CLOCK_EVT_FEAT_HRTIMER,
.rating = 0,
.bound_on = -1,
.min_delta_ns = 1,
.max_delta_ns = KTIME_MAX,
.min_delta_ticks = 1,
.max_delta_ticks = ULONG_MAX,
.mult = 1,
.shift = 0,
.cpumask = cpu_all_mask,
};
static enum hrtimer_restart bc_handler(struct hrtimer *t)
{
ce_broadcast_hrtimer.event_handler(&ce_broadcast_hrtimer);
if (ce_broadcast_hrtimer.next_event.tv64 == KTIME_MAX)
return HRTIMER_NORESTART;
return HRTIMER_RESTART;
}
void tick_setup_hrtimer_broadcast(void)
{
hrtimer_init(&bctimer, CLOCK_MONOTONIC, HRTIMER_MODE_ABS);
bctimer.function = bc_handler;
clockevents_register_device(&ce_broadcast_hrtimer);
}
......@@ -120,6 +120,19 @@ int tick_is_broadcast_device(struct clock_event_device *dev)
return (dev && tick_broadcast_device.evtdev == dev);
}
int tick_broadcast_update_freq(struct clock_event_device *dev, u32 freq)
{
int ret = -ENODEV;
if (tick_is_broadcast_device(dev)) {
raw_spin_lock(&tick_broadcast_lock);
ret = __clockevents_update_freq(dev, freq);
raw_spin_unlock(&tick_broadcast_lock);
}
return ret;
}
static void err_broadcast(const struct cpumask *mask)
{
pr_crit_once("Failed to broadcast timer tick. Some CPUs may be unresponsive.\n");
......@@ -272,12 +285,8 @@ static void tick_do_broadcast(struct cpumask *mask)
*/
static void tick_do_periodic_broadcast(void)
{
raw_spin_lock(&tick_broadcast_lock);
cpumask_and(tmpmask, cpu_online_mask, tick_broadcast_mask);
tick_do_broadcast(tmpmask);
raw_spin_unlock(&tick_broadcast_lock);
}
/*
......@@ -287,13 +296,15 @@ static void tick_handle_periodic_broadcast(struct clock_event_device *dev)
{
ktime_t next;
raw_spin_lock(&tick_broadcast_lock);
tick_do_periodic_broadcast();
/*
* The device is in periodic mode. No reprogramming necessary:
*/
if (dev->mode == CLOCK_EVT_MODE_PERIODIC)
return;
goto unlock;
/*
* Setup the next period for devices, which do not have
......@@ -306,9 +317,11 @@ static void tick_handle_periodic_broadcast(struct clock_event_device *dev)
next = ktime_add(next, tick_period);
if (!clockevents_program_event(dev, next, false))
return;
goto unlock;
tick_do_periodic_broadcast();
}
unlock:
raw_spin_unlock(&tick_broadcast_lock);
}
/*
......@@ -630,24 +643,61 @@ static void tick_handle_oneshot_broadcast(struct clock_event_device *dev)
raw_spin_unlock(&tick_broadcast_lock);
}
static int broadcast_needs_cpu(struct clock_event_device *bc, int cpu)
{
if (!(bc->features & CLOCK_EVT_FEAT_HRTIMER))
return 0;
if (bc->next_event.tv64 == KTIME_MAX)
return 0;
return bc->bound_on == cpu ? -EBUSY : 0;
}
static void broadcast_shutdown_local(struct clock_event_device *bc,
struct clock_event_device *dev)
{
/*
* For hrtimer based broadcasting we cannot shutdown the cpu
* local device if our own event is the first one to expire or
* if we own the broadcast timer.
*/
if (bc->features & CLOCK_EVT_FEAT_HRTIMER) {
if (broadcast_needs_cpu(bc, smp_processor_id()))
return;
if (dev->next_event.tv64 < bc->next_event.tv64)
return;
}
clockevents_set_mode(dev, CLOCK_EVT_MODE_SHUTDOWN);
}
static void broadcast_move_bc(int deadcpu)
{
struct clock_event_device *bc = tick_broadcast_device.evtdev;
if (!bc || !broadcast_needs_cpu(bc, deadcpu))
return;
/* This moves the broadcast assignment to this cpu */
clockevents_program_event(bc, bc->next_event, 1);
}
/*
* Powerstate information: The system enters/leaves a state, where
* affected devices might stop
* Returns 0 on success, -EBUSY if the cpu is used to broadcast wakeups.
*/
void tick_broadcast_oneshot_control(unsigned long reason)
int tick_broadcast_oneshot_control(unsigned long reason)
{
struct clock_event_device *bc, *dev;
struct tick_device *td;
unsigned long flags;
ktime_t now;
int cpu;
int cpu, ret = 0;
/*
* Periodic mode does not care about the enter/exit of power
* states
*/
if (tick_broadcast_device.mode == TICKDEV_MODE_PERIODIC)
return;
return 0;
/*
* We are called with preemtion disabled from the depth of the
......@@ -658,7 +708,7 @@ void tick_broadcast_oneshot_control(unsigned long reason)
dev = td->evtdev;
if (!(dev->features & CLOCK_EVT_FEAT_C3STOP))
return;
return 0;
bc = tick_broadcast_device.evtdev;
......@@ -666,7 +716,7 @@ void tick_broadcast_oneshot_control(unsigned long reason)
if (reason == CLOCK_EVT_NOTIFY_BROADCAST_ENTER) {
if (!cpumask_test_and_set_cpu(cpu, tick_broadcast_oneshot_mask)) {
WARN_ON_ONCE(cpumask_test_cpu(cpu, tick_broadcast_pending_mask));
clockevents_set_mode(dev, CLOCK_EVT_MODE_SHUTDOWN);
broadcast_shutdown_local(bc, dev);
/*
* We only reprogram the broadcast timer if we
* did not mark ourself in the force mask and
......@@ -679,6 +729,16 @@ void tick_broadcast_oneshot_control(unsigned long reason)
dev->next_event.tv64 < bc->next_event.tv64)
tick_broadcast_set_event(bc, cpu, dev->next_event, 1);
}
/*
* If the current CPU owns the hrtimer broadcast
* mechanism, it cannot go deep idle and we remove the
* CPU from the broadcast mask. We don't have to go
* through the EXIT path as the local timer is not
* shutdown.
*/
ret = broadcast_needs_cpu(bc, cpu);
if (ret)
cpumask_clear_cpu(cpu, tick_broadcast_oneshot_mask);
} else {
if (cpumask_test_and_clear_cpu(cpu, tick_broadcast_oneshot_mask)) {
clockevents_set_mode(dev, CLOCK_EVT_MODE_ONESHOT);
......@@ -746,6 +806,7 @@ void tick_broadcast_oneshot_control(unsigned long reason)
}
out:
raw_spin_unlock_irqrestore(&tick_broadcast_lock, flags);
return ret;
}
/*
......@@ -852,6 +913,8 @@ void tick_shutdown_broadcast_oneshot(unsigned int *cpup)
cpumask_clear_cpu(cpu, tick_broadcast_pending_mask);
cpumask_clear_cpu(cpu, tick_broadcast_force_mask);
broadcast_move_bc(cpu);
raw_spin_unlock_irqrestore(&tick_broadcast_lock, flags);
}
......
......@@ -98,18 +98,19 @@ static void tick_periodic(int cpu)
void tick_handle_periodic(struct clock_event_device *dev)
{
int cpu = smp_processor_id();
ktime_t next;
ktime_t next = dev->next_event;
tick_periodic(cpu);
if (dev->mode != CLOCK_EVT_MODE_ONESHOT)
return;
/*
* Setup the next period for devices, which do not have
* periodic mode:
*/
next = ktime_add(dev->next_event, tick_period);
for (;;) {
/*
* Setup the next period for devices, which do not have
* periodic mode:
*/
next = ktime_add(next, tick_period);
if (!clockevents_program_event(dev, next, false))
return;
/*
......@@ -118,12 +119,11 @@ void tick_handle_periodic(struct clock_event_device *dev)
* to be sure we're using a real hardware clocksource.
* Otherwise we could get trapped in an infinite
* loop, as the tick_periodic() increments jiffies,
* when then will increment time, posibly causing
* which then will increment time, possibly causing
* the loop to trigger again and again.
*/
if (timekeeping_valid_for_hres())
tick_periodic(cpu);
next = ktime_add(next, tick_period);
}
}
......
......@@ -46,7 +46,7 @@ extern int tick_switch_to_oneshot(void (*handler)(struct clock_event_device *));
extern void tick_resume_oneshot(void);
# ifdef CONFIG_GENERIC_CLOCKEVENTS_BROADCAST
extern void tick_broadcast_setup_oneshot(struct clock_event_device *bc);
extern void tick_broadcast_oneshot_control(unsigned long reason);
extern int tick_broadcast_oneshot_control(unsigned long reason);
extern void tick_broadcast_switch_to_oneshot(void);
extern void tick_shutdown_broadcast_oneshot(unsigned int *cpup);
extern int tick_resume_broadcast_oneshot(struct clock_event_device *bc);
......@@ -58,7 +58,7 @@ static inline void tick_broadcast_setup_oneshot(struct clock_event_device *bc)
{
BUG();
}
static inline void tick_broadcast_oneshot_control(unsigned long reason) { }
static inline int tick_broadcast_oneshot_control(unsigned long reason) { return 0; }
static inline void tick_broadcast_switch_to_oneshot(void) { }
static inline void tick_shutdown_broadcast_oneshot(unsigned int *cpup) { }
static inline int tick_broadcast_oneshot_active(void) { return 0; }
......@@ -87,7 +87,7 @@ static inline void tick_broadcast_setup_oneshot(struct clock_event_device *bc)
{
BUG();
}
static inline void tick_broadcast_oneshot_control(unsigned long reason) { }
static inline int tick_broadcast_oneshot_control(unsigned long reason) { return 0; }
static inline void tick_shutdown_broadcast_oneshot(unsigned int *cpup) { }
static inline int tick_resume_broadcast_oneshot(struct clock_event_device *bc)
{
......@@ -111,6 +111,7 @@ extern int tick_resume_broadcast(void);
extern void tick_broadcast_init(void);
extern void
tick_set_periodic_handler(struct clock_event_device *dev, int broadcast);
int tick_broadcast_update_freq(struct clock_event_device *dev, u32 freq);
#else /* !BROADCAST */
......@@ -133,6 +134,8 @@ static inline void tick_shutdown_broadcast(unsigned int *cpup) { }
static inline void tick_suspend_broadcast(void) { }
static inline int tick_resume_broadcast(void) { return 0; }
static inline void tick_broadcast_init(void) { }
static inline int tick_broadcast_update_freq(struct clock_event_device *dev,
u32 freq) { return -ENODEV; }
/*
* Set the periodic handler in non broadcast mode
......@@ -152,6 +155,8 @@ static inline int tick_device_is_functional(struct clock_event_device *dev)
return !(dev->features & CLOCK_EVT_FEAT_DUMMY);
}
int __clockevents_update_freq(struct clock_event_device *dev, u32 freq);
#endif
extern void do_timer(unsigned long ticks);
......
......@@ -21,6 +21,8 @@
#include <linux/seq_file.h>
#include <linux/time.h>
#include "timekeeping_internal.h"
static unsigned int sleep_time_bin[32] = {0};
static int tk_debug_show_sleep_time(struct seq_file *s, void *data)
......
......@@ -81,6 +81,7 @@ struct tvec_base {
unsigned long timer_jiffies;
unsigned long next_timer;
unsigned long active_timers;
unsigned long all_timers;
struct tvec_root tv1;
struct tvec tv2;
struct tvec tv3;
......@@ -337,6 +338,20 @@ void set_timer_slack(struct timer_list *timer, int slack_hz)
}
EXPORT_SYMBOL_GPL(set_timer_slack);
/*
* If the list is empty, catch up ->timer_jiffies to the current time.
* The caller must hold the tvec_base lock. Returns true if the list
* was empty and therefore ->timer_jiffies was updated.
*/
static bool catchup_timer_jiffies(struct tvec_base *base)
{
if (!base->all_timers) {
base->timer_jiffies = jiffies;
return true;
}
return false;
}
static void
__internal_add_timer(struct tvec_base *base, struct timer_list *timer)
{
......@@ -383,15 +398,17 @@ __internal_add_timer(struct tvec_base *base, struct timer_list *timer)
static void internal_add_timer(struct tvec_base *base, struct timer_list *timer)
{
(void)catchup_timer_jiffies(base);
__internal_add_timer(base, timer);
/*
* Update base->active_timers and base->next_timer
*/
if (!tbase_get_deferrable(timer->base)) {
if (time_before(timer->expires, base->next_timer))
if (!base->active_timers++ ||
time_before(timer->expires, base->next_timer))
base->next_timer = timer->expires;
base->active_timers++;
}
base->all_timers++;
}
#ifdef CONFIG_TIMER_STATS
......@@ -671,6 +688,8 @@ detach_expired_timer(struct timer_list *timer, struct tvec_base *base)
detach_timer(timer, true);
if (!tbase_get_deferrable(timer->base))
base->active_timers--;
base->all_timers--;
(void)catchup_timer_jiffies(base);
}
static int detach_if_pending(struct timer_list *timer, struct tvec_base *base,
......@@ -685,6 +704,8 @@ static int detach_if_pending(struct timer_list *timer, struct tvec_base *base,
if (timer->expires == base->next_timer)
base->next_timer = base->timer_jiffies;
}
base->all_timers--;
(void)catchup_timer_jiffies(base);
return 1;
}
......@@ -739,12 +760,7 @@ __mod_timer(struct timer_list *timer, unsigned long expires,
debug_activate(timer, expires);
cpu = smp_processor_id();
#if defined(CONFIG_NO_HZ_COMMON) && defined(CONFIG_SMP)
if (!pinned && get_sysctl_timer_migration() && idle_cpu(cpu))
cpu = get_nohz_timer_target();
#endif
cpu = get_nohz_timer_target(pinned);
new_base = per_cpu(tvec_bases, cpu);
if (base != new_base) {
......@@ -939,8 +955,15 @@ void add_timer_on(struct timer_list *timer, int cpu)
* with the timer by holding the timer base lock. This also
* makes sure that a CPU on the way to stop its tick can not
* evaluate the timer wheel.
*
* Spare the IPI for deferrable timers on idle targets though.
* The next busy ticks will take care of it. Except full dynticks
* require special care against races with idle_cpu(), lets deal
* with that later.
*/
wake_up_nohz_cpu(cpu);
if (!tbase_get_deferrable(timer->base) || tick_nohz_full_cpu(cpu))
wake_up_nohz_cpu(cpu);
spin_unlock_irqrestore(&base->lock, flags);
}
EXPORT_SYMBOL_GPL(add_timer_on);
......@@ -1146,6 +1169,10 @@ static inline void __run_timers(struct tvec_base *base)
struct timer_list *timer;
spin_lock_irq(&base->lock);
if (catchup_timer_jiffies(base)) {
spin_unlock_irq(&base->lock);
return;
}
while (time_after_eq(jiffies, base->timer_jiffies)) {
struct list_head work_list;
struct list_head *head = &work_list;
......@@ -1160,7 +1187,7 @@ static inline void __run_timers(struct tvec_base *base)
!cascade(base, &base->tv4, INDEX(2)))
cascade(base, &base->tv5, INDEX(3));
++base->timer_jiffies;
list_replace_init(base->tv1.vec + index, &work_list);
list_replace_init(base->tv1.vec + index, head);
while (!list_empty(head)) {
void (*fn)(unsigned long);
unsigned long data;
......@@ -1523,9 +1550,8 @@ static int init_timers_cpu(int cpu)
if (!base)
return -ENOMEM;
/* Make sure that tvec_base is 2 byte aligned */
if (tbase_get_deferrable(base)) {
WARN_ON(1);
/* Make sure tvec_base has TIMER_FLAG_MASK bits free */
if (WARN_ON(base != tbase_get_base(base))) {
kfree(base);
return -ENOMEM;
}
......@@ -1559,6 +1585,7 @@ static int init_timers_cpu(int cpu)
base->timer_jiffies = jiffies;
base->next_timer = base->timer_jiffies;
base->active_timers = 0;
base->all_timers = 0;
return 0;
}
......@@ -1648,9 +1675,9 @@ void __init init_timers(void)
err = timer_cpu_notify(&timers_nb, (unsigned long)CPU_UP_PREPARE,
(void *)(long)smp_processor_id());
init_timer_stats();
BUG_ON(err != NOTIFY_OK);
init_timer_stats();
register_cpu_notifier(&timers_nb);
open_softirq(TIMER_SOFTIRQ, run_timer_softirq);
}
......
......@@ -516,6 +516,13 @@ void destroy_work_on_stack(struct work_struct *work)
}
EXPORT_SYMBOL_GPL(destroy_work_on_stack);
void destroy_delayed_work_on_stack(struct delayed_work *work)
{
destroy_timer_on_stack(&work->timer);
debug_object_free(&work->work, &work_debug_descr);
}
EXPORT_SYMBOL_GPL(destroy_delayed_work_on_stack);
#else
static inline void debug_work_activate(struct work_struct *work) { }
static inline void debug_work_deactivate(struct work_struct *work) { }
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment