ARM: dts: sun6i: Provide default muxing for relevant controllers

The I2C and MMC controllers have only one muxing option in the SoC. In such a
case, we can just move the muxing into the DTSI, and remove it from
the DTS.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

arch/arm/boot/dts/sun6i-a31-colombus.dts

@@ -88,20 +88,14 @@ phy1: ethernet-phy@1 {
 };
 
 &i2c0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c0_pins>;
 	status = "fail";
 };
 
 &i2c1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins>;
 	status = "okay";
 };
 
 &i2c2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c2_pins>;
 	status = "okay";
 
 	mma8452: mma8452@1d {
@@ -113,8 +107,6 @@ mma8452: mma8452@1d {
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins>;
 	vmmc-supply = <&reg_vcc3v0>;
 	bus-width = <4>;
 	cd-gpios = <&pio 0 8 GPIO_ACTIVE_LOW>; /* PA8 */

arch/arm/boot/dts/sun6i-a31-hummingbird.dts

@@ -184,21 +184,15 @@ hdmi_out_con: endpoint {
 };
 
 &i2c0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c0_pins>;
 	/* pull-ups and devices require AXP221 DLDO3 */
 	status = "failed";
 };
 
 &i2c1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins>;
 	status = "okay";
 };
 
 &i2c2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c2_pins>;
 	status = "okay";
 
 	pcf8563: rtc@51 {
@@ -214,8 +208,6 @@ &ir {
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins>;
 	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <4>;
 	cd-gpios = <&pio 0 8 GPIO_ACTIVE_LOW>; /* PA8 */
@@ -223,8 +215,6 @@ &mmc0 {
 };
 
 &mmc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc1_pins>;
 	vmmc-supply = <&reg_aldo1>;
 	mmc-pwrseq = <&wifi_pwrseq>;
 	bus-width = <4>;

arch/arm/boot/dts/sun6i-a31-i7.dts

@@ -143,8 +143,6 @@ &ir {
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
 	cd-gpios = <&pio 7 22 GPIO_ACTIVE_LOW>; /* PH22 */

arch/arm/boot/dts/sun6i-a31-m9.dts

@@ -101,8 +101,6 @@ &ir {
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins>;
 	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <4>;
 	cd-gpios = <&pio 7 22 GPIO_ACTIVE_LOW>; /* PH22 */

arch/arm/boot/dts/sun6i-a31-mele-a1000g-quad.dts

@@ -101,8 +101,6 @@ &ir {
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins>;
 	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <4>;
 	cd-gpios = <&pio 7 22 GPIO_ACTIVE_LOW>; /* PH22 */

arch/arm/boot/dts/sun6i-a31.dtsi

@@ -388,6 +388,8 @@ mmc0: mmc@1c0f000 {
 			resets = <&ccu RST_AHB1_MMC0>;
 			reset-names = "ahb";
 			interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc0_pins>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -407,6 +409,8 @@ mmc1: mmc@1c10000 {
 			resets = <&ccu RST_AHB1_MMC1>;
 			reset-names = "ahb";
 			interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc1_pins>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -878,6 +882,8 @@ i2c0: i2c@1c2ac00 {
 			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_APB2_I2C0>;
 			resets = <&ccu RST_APB2_I2C0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c0_pins>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -889,6 +895,8 @@ i2c1: i2c@1c2b000 {
 			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_APB2_I2C1>;
 			resets = <&ccu RST_APB2_I2C1>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c1_pins>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -900,6 +908,8 @@ i2c2: i2c@1c2b400 {
 			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_APB2_I2C2>;
 			resets = <&ccu RST_APB2_I2C2>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c2_pins>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;

arch/arm/boot/dts/sun6i-a31s-inet-q972.dts

@@ -54,8 +54,6 @@ &ehci1 {
 };
 
 &i2c1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins>;
 	status = "okay";
 
 	ft5406ee8: touchscreen@38 {

arch/arm/boot/dts/sun6i-a31s-primo81.dts

@@ -90,14 +90,10 @@ hdmi_out_con: endpoint {
 
 &i2c0 {
 	/* pull-ups and device VDDIO use AXP221 DLDO3 */
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c0_pins>;
 	status = "failed";
 };
 
 &i2c1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins>;
 	status = "okay";
 
 	ctp@5d {
@@ -110,8 +106,6 @@ ctp@5d {
 };
 
 &i2c2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c2_pins>;
 	status = "okay";
 
 	accelerometer@1c {
@@ -145,8 +139,6 @@ button-349 {
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins>;
 	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <4>;
 	cd-gpios = <&pio 0 8 GPIO_ACTIVE_LOW>; /* PA8 */

arch/arm/boot/dts/sun6i-a31s-sina31s.dts

@@ -161,8 +161,6 @@ button-349 {
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins>;
 	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <4>;
 	cd-gpios = <&pio 0 4 GPIO_ACTIVE_LOW>; /* PA4 */

arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts

@@ -112,8 +112,6 @@ &ir {
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins>;
 	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <4>;
 	cd-gpios = <&pio 0 4 GPIO_ACTIVE_LOW>; /* PA4 */

arch/arm/boot/dts/sun6i-a31s-yones-toptech-bs1078-v2.dts

@@ -62,14 +62,10 @@ chosen {
 };
 
 &i2c1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins>;
 	status = "okay";
 };
 
 &i2c2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c2_pins>;
 	status = "okay";
 };
 
@@ -90,8 +86,6 @@ &ohci1 {
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins>;
 	vmmc-supply = <&reg_vcc3v0>;
 	bus-width = <4>;
 	cd-gpios = <&pio 0 8 GPIO_ACTIVE_LOW>; /* PA8 */