media: dvb: earth-pt1: replace schedule_timeout with usleep_range

As described in Document/timers/timers-howto.txt,
hrtimer-based delay should be used for small sleeps.
Signed-off-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

drivers/media/pci/pt1/pt1.c

@@ -18,7 +18,10 @@
  */
 
 #include <linux/kernel.h>
+#include <linux/sched.h>
 #include <linux/sched/signal.h>
+#include <linux/hrtimer.h>
+#include <linux/delay.h>
 #include <linux/module.h>
 #include <linux/slab.h>
 #include <linux/vmalloc.h>
@@ -321,7 +324,7 @@ static int pt1_unlock(struct pt1 *pt1)
 	for (i = 0; i < 3; i++) {
 		if (pt1_read_reg(pt1, 0) & 0x80000000)
 			return 0;
-		schedule_timeout_uninterruptible((HZ + 999) / 1000);
+		usleep_range(1000, 2000);
 	}
 	dev_err(&pt1->pdev->dev, "could not unlock\n");
 	return -EIO;
@@ -335,7 +338,7 @@ static int pt1_reset_pci(struct pt1 *pt1)
 	for (i = 0; i < 10; i++) {
 		if (pt1_read_reg(pt1, 0) & 0x00000001)
 			return 0;
-		schedule_timeout_uninterruptible((HZ + 999) / 1000);
+		usleep_range(1000, 2000);
 	}
 	dev_err(&pt1->pdev->dev, "could not reset PCI\n");
 	return -EIO;
@@ -349,7 +352,7 @@ static int pt1_reset_ram(struct pt1 *pt1)
 	for (i = 0; i < 10; i++) {
 		if (pt1_read_reg(pt1, 0) & 0x00000002)
 			return 0;
-		schedule_timeout_uninterruptible((HZ + 999) / 1000);
+		usleep_range(1000, 2000);
 	}
 	dev_err(&pt1->pdev->dev, "could not reset RAM\n");
 	return -EIO;
@@ -366,7 +369,7 @@ static int pt1_do_enable_ram(struct pt1 *pt1)
 			if ((pt1_read_reg(pt1, 0) & 0x00000004) != status)
 				return 0;
 		}
-		schedule_timeout_uninterruptible((HZ + 999) / 1000);
+		usleep_range(1000, 2000);
 	}
 	dev_err(&pt1->pdev->dev, "could not enable RAM\n");
 	return -EIO;
@@ -376,7 +379,7 @@ static int pt1_enable_ram(struct pt1 *pt1)
 {
 	int i, ret;
 	int phase;
-	schedule_timeout_uninterruptible((HZ + 999) / 1000);
+	usleep_range(1000, 2000);
 	phase = pt1->pdev->device == 0x211a ? 128 : 166;
 	for (i = 0; i < phase; i++) {
 		ret = pt1_do_enable_ram(pt1);
@@ -463,6 +466,9 @@ static int pt1_thread(void *data)
 	struct pt1_buffer_page *page;
 	bool was_frozen;
 
+#define PT1_FETCH_DELAY 10
+#define PT1_FETCH_DELAY_DELTA 2
+
 	pt1 = data;
 	set_freezable();
 
@@ -476,7 +482,13 @@ static int pt1_thread(void *data)
 
 		page = pt1->tables[pt1->table_index].bufs[pt1->buf_index].page;
 		if (!pt1_filter(pt1, page)) {
-			schedule_timeout_interruptible((HZ + 999) / 1000);
+			ktime_t delay;
+
+			delay = PT1_FETCH_DELAY * NSEC_PER_MSEC;
+			set_current_state(TASK_INTERRUPTIBLE);
+			schedule_hrtimeout_range(&delay,
+					PT1_FETCH_DELAY_DELTA * NSEC_PER_MSEC,
+					HRTIMER_MODE_REL);
 			continue;
 		}
 
@@ -712,7 +724,7 @@ pt1_update_power(struct pt1 *pt1)
 		adap = pt1->adaps[i];
 		switch (adap->voltage) {
 		case SEC_VOLTAGE_13: /* actually 11V */
-			bits |= 1 << 1;
+			bits |= 1 << 2;
 			break;
 		case SEC_VOLTAGE_18: /* actually 15V */
 			bits |= 1 << 1 | 1 << 2;
@@ -766,7 +778,7 @@ static int pt1_wakeup(struct dvb_frontend *fe)
 	adap = container_of(fe->dvb, struct pt1_adapter, adap);
 	adap->sleep = 0;
 	pt1_update_power(adap->pt1);
-	schedule_timeout_uninterruptible((HZ + 999) / 1000);
+	usleep_range(1000, 2000);
 
 	ret = config_demod(adap->demod_i2c_client, adap->pt1->fe_clk);
 	if (ret == 0 && adap->orig_init)
@@ -1073,7 +1085,7 @@ static int pt1_i2c_end(struct pt1 *pt1, int addr)
 	do {
 		if (signal_pending(current))
 			return -EINTR;
-		schedule_timeout_interruptible((HZ + 999) / 1000);
+		usleep_range(1000, 2000);
 	} while (pt1_read_reg(pt1, 0) & 0x00000080);
 	return 0;
 }
@@ -1376,11 +1388,11 @@ static int pt1_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 
 	pt1->power = 1;
 	pt1_update_power(pt1);
-	schedule_timeout_uninterruptible((HZ + 49) / 50);
+	msleep(20);
 
 	pt1->reset = 0;
 	pt1_update_power(pt1);
-	schedule_timeout_uninterruptible((HZ + 999) / 1000);
+	usleep_range(1000, 2000);
 
 	ret = pt1_init_frontends(pt1);
 	if (ret < 0)