Merge tag 'omap-for-v3.15/dt-signed' of...

Merge tag 'omap-for-v3.15/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt

OMAP device tree changes from Tony Lindgren:

Device tree related changes for omaps with minor code
changes also to platform data quirks that are still needed
for some features.

* tag 'omap-for-v3.15/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (60 commits)
  ARM: dts: omap4+: Add DMM bindings
  ARM: dts: am43x-gp-evm: Add matrix gpio keys.
  ARM: dts: am43xx: add support for parallel NAND flash
  ARM: dts: AM33xx: updated default ECC scheme in nand-ecc-opt
  ARM: dts: am335x-evm: NAND: update MTD partition table
  ARM: OMAP2+: gpmc: update gpmc_hwecc_bch_capable() for new platforms and ECC schemes
  ARM: dts: omap3-gta04: Add bma180 accelerometer
  ARM: dts: omap3-gta04: Enable mmc2 for wifi
  ARM: dts: omap3-gta04: Add basic sound support
  ARM: dts: omap3-gta04: Add twl4030 charger
  ARM: dts: omap3-gta04: Add touchscreen properties
  ARM: dts: omap3-gta04: Add support for magnetometer
  ARM: dts: am437x-gp-evm: Enable gpio.
  ARM: dts: am437x-gp-evm: Add pwm backlight support.
  ARM: dts: am437x-gp-evm: Add gp dts.
  ARM: dts: am43x-epos-evm: Add SPI data.
  ARM: dts: am43x-epos-evm: Add I2C2 data.
  pinctrl: am43xx: dt-bindings: add MUX_MODE8
  ARM: dts: am43x-epos-evm: Add pwm backlight support.
  ARM: dts: am4372: Add pwm-cells property for ecap device.
  ...

Documentation/devicetree/bindings/arm/omap/dmm.txt

+OMAP Dynamic Memory Manager (DMM) bindings
+
+The dynamic memory manager (DMM) is a module located immediately in front of the
+SDRAM controllers (called EMIFs on OMAP). DMM manages various aspects of memory
+accesses such as priority generation amongst initiators, configuration of SDRAM
+interleaving, optimizing transfer of 2D block objects, and provide MMU-like page
+translation for initiators which need contiguous dma bus addresses.
+
+Required properties:
+- compatible:	Should contain "ti,omap4-dmm" for OMAP4 family
+		Should contain "ti,omap5-dmm" for OMAP5 and DRA7x family
+- reg:		Contains DMM register address range (base address and length)
+- interrupts:	Should contain an interrupt-specifier for DMM_IRQ.
+- ti,hwmods:	Name of the hwmod associated to DMM, which is typically "dmm"
+
+Example:
+
+dmm@4e000000 {
+	compatible = "ti,omap4-dmm";
+	reg = <0x4e000000 0x800>;
+	ti,hwmods = "dmm";
+};

Documentation/devicetree/bindings/arm/omap/omap.txt

@@ -114,5 +114,8 @@ Boards:
 - AM43x EPOS EVM
   compatible = "ti,am43x-epos-evm", "ti,am4372", "ti,am43"
 
+- AM437x GP EVM
+  compatible = "ti,am437x-gp-evm", "ti,am4372", "ti,am43"
+
 - DRA7 EVM:  Software Developement Board for DRA7XX
   compatible = "ti,dra7-evm", "ti,dra7"

arch/arm/boot/dts/Makefile

@@ -228,6 +228,10 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
 	omap2420-n810-wimax.dtb \
 	omap3430-sdp.dtb \
 	omap3-beagle.dtb \
+	omap3-cm-t3517.dtb \
+	omap3-sbc-t3517.dtb \
+	omap3-cm-t3530.dtb \
+	omap3-sbc-t3530.dtb \
 	omap3-cm-t3730.dtb \
 	omap3-sbc-t3730.dtb \
 	omap3-devkit8000.dtb \
@@ -242,6 +246,7 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
 	omap3-gta04.dtb \
 	omap3-igep0020.dtb \
 	omap3-igep0030.dtb \
+	omap3-lilly-dbb056.dtb \
 	omap3-zoom3.dtb \
 	omap4-panda.dtb \
 	omap4-panda-a4.dtb \
@@ -256,9 +261,11 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
 	am335x-boneblack.dtb \
 	am335x-nano.dtb \
 	am335x-base0033.dtb \
+	am3517-craneboard.dtb \
 	am3517-evm.dtb \
 	am3517_mt_ventoux.dtb \
 	am43x-epos-evm.dtb \
+	am437x-gp-evm.dtb \
 	dra7-evm.dtb
 dtb-$(CONFIG_ARCH_ORION5X) += orion5x-lacie-ethernet-disk-mini-v2.dtb
 dtb-$(CONFIG_ARCH_PRIMA2) += prima2-evb.dtb

arch/arm/boot/dts/am335x-evm.dts

@@ -434,9 +434,9 @@ &gpmc {
 	ranges = <0 0 0x08000000 0x10000000>;	/* CS0: NAND */
 	nand@0,0 {
 		reg = <0 0 0>; /* CS0, offset 0 */
-		nand-bus-width = <8>;
 		ti,nand-ecc-opt = "bch8";
-		gpmc,device-nand = "true";
+		ti,elm-id = <&elm>;
+		nand-bus-width = <8>;
 		gpmc,device-width = <1>;
 		gpmc,sync-clk-ps = <0>;
 		gpmc,cs-on-ns = <0>;
@@ -460,50 +460,51 @@ nand@0,0 {
 		gpmc,wait-monitoring-ns = <0>;
 		gpmc,wr-access-ns = <40>;
 		gpmc,wr-data-mux-bus-ns = <0>;
-
+		/* MTD partition table */
+		/* All SPL-* partitions are sized to minimal length
+		 * which can be independently programmable. For
+		 * NAND flash this is equal to size of erase-block */
 		#address-cells = <1>;
 		#size-cells = <1>;
-		elm_id = <&elm>;
-
-		/* MTD partition table */
 		partition@0 {
-			label = "SPL1";
+			label = "NAND.SPL";
 			reg = <0x00000000 0x000020000>;
 		};
-
 		partition@1 {
-			label = "SPL2";
+			label = "NAND.SPL.backup1";
 			reg = <0x00020000 0x00020000>;
 		};
-
 		partition@2 {
-			label = "SPL3";
+			label = "NAND.SPL.backup2";
 			reg = <0x00040000 0x00020000>;
 		};
-
 		partition@3 {
-			label = "SPL4";
+			label = "NAND.SPL.backup3";
 			reg = <0x00060000 0x00020000>;
 		};
-
 		partition@4 {
-			label = "U-boot";
-			reg = <0x00080000 0x001e0000>;
+			label = "NAND.u-boot-spl";
+			reg = <0x00080000 0x00040000>;
 		};
-
 		partition@5 {
-			label = "environment";
-			reg = <0x00260000 0x00020000>;
+			label = "NAND.u-boot";
+			reg = <0x000C0000 0x00100000>;
 		};
-
 		partition@6 {
-			label = "Kernel";
-			reg = <0x00280000 0x00500000>;
+			label = "NAND.u-boot-env";
+			reg = <0x001C0000 0x00020000>;
 		};
-
 		partition@7 {
-			label = "File-System";
-			reg = <0x00780000 0x0F880000>;
+			label = "NAND.u-boot-env.backup1";
+			reg = <0x001E0000 0x00020000>;
+		};
+		partition@8 {
+			label = "NAND.kernel";
+			reg = <0x00200000 0x00800000>;
+		};
+		partition@9 {
+			label = "NAND.file-system";
+			reg = <0x00A00000 0x0F600000>;
 		};
 	};
 };

arch/arm/boot/dts/am335x-evmsk.dts

@@ -121,7 +121,7 @@ sound {
 		ti,model = "AM335x-EVMSK";
 		ti,audio-codec = <&tlv320aic3106>;
 		ti,mcasp-controller = <&mcasp1>;
-		ti,codec-clock-rate = <24576000>;
+		ti,codec-clock-rate = <24000000>;
 		ti,audio-routing =
 			"Headphone Jack",       "HPLOUT",
 			"Headphone Jack",       "HPROUT";
@@ -336,9 +336,18 @@ usb-phy@47401300 {
 		status = "okay";
 	};
 
+	usb-phy@47401b00 {
+		status = "okay";
+	};
+
 	usb@47401000 {
 		status = "okay";
 	};
+
+	usb@47401800 {
+		status = "okay";
+		dr_mode = "host";
+	};
 };
 
 &epwmss2 {

arch/arm/boot/dts/am33xx.dtsi

@@ -58,6 +58,10 @@ cpu@0 {
 				275000  1125000
 			>;
 			voltage-tolerance = <2>; /* 2 percentage */
+
+			clocks = <&dpll_mpu_ck>;
+			clock-names = "cpu";
+
 			clock-latency = <300000>; /* From omap-cpufreq driver */
 		};
 	};
@@ -318,6 +322,7 @@ hwspinlock: spinlock@480ca000 {
 			compatible = "ti,omap4-hwspinlock";
 			reg = <0x480ca000 0x1000>;
 			ti,hwmods = "spinlock";
+			#hwlock-cells = <1>;
 		};
 
 		wdt2: wdt@44e35000 {
@@ -399,7 +404,7 @@ timer7: timer@4804a000 {
 			ti,timer-pwm;
 		};
 
-		rtc@44e3e000 {
+		rtc: rtc@44e3e000 {
 			compatible = "ti,da830-rtc";
 			reg = <0x44e3e000 0x1000>;
 			interrupts = <75
@@ -582,6 +587,8 @@ ecap0: ecap@48300100 {
 				compatible = "ti,am33xx-ecap";
 				#pwm-cells = <3>;
 				reg = <0x48300100 0x80>;
+				interrupts = <31>;
+				interrupt-names = "ecap0";
 				ti,hwmods = "ecap0";
 				status = "disabled";
 			};
@@ -610,6 +617,8 @@ ecap1: ecap@48302100 {
 				compatible = "ti,am33xx-ecap";
 				#pwm-cells = <3>;
 				reg = <0x48302100 0x80>;
+				interrupts = <47>;
+				interrupt-names = "ecap1";
 				ti,hwmods = "ecap1";
 				status = "disabled";
 			};
@@ -638,6 +647,8 @@ ecap2: ecap@48304100 {
 				compatible = "ti,am33xx-ecap";
 				#pwm-cells = <3>;
 				reg = <0x48304100 0x80>;
+				interrupts = <61>;
+				interrupt-names = "ecap2";
 				ti,hwmods = "ecap2";
 				status = "disabled";
 			};

arch/arm/boot/dts/am3517-craneboard.dts

+/*
+ * See craneboard.org for more details
+ *
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "am3517.dtsi"
+
+/ {
+	model = "TI AM3517 CraneBoard (TMDSEVM3517)";
+	compatible = "ti,am3517-craneboard", "ti,am3517", "ti,omap3";
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>;	/* 256 MB */
+	};
+
+	vbat: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vbat";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+	};
+};
+
+&davinci_emac {
+	status = "okay";
+};
+
+&davinci_mdio {
+	status = "okay";
+};
+
+&i2c1 {
+	clock-frequency = <2600000>;
+
+	tps: tps@2d {
+		reg = <0x2d>;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+	/* goes to expansion connector */
+	status = "disabled";
+};
+
+&i2c3 {
+	clock-frequency = <400000>;
+	/* goes to expansion connector */
+	status = "disabled";
+};
+
+&mmc1 {
+	vmmc-supply = <&vdd2_reg>;
+	bus-width = <8>;
+};
+
+&mmc2 {
+	/* goes to expansion connector */
+	status = "disabled";
+};
+
+&mmc3 {
+	/* goes to expansion connector */
+	status = "disabled";
+};
+
+#include "tps65910.dtsi"
+
+&omap3_pmx_core {
+	tps_pins: pinmux_tps_pins {
+		pinctrl-single,pins = <
+			0x1b0 (PIN_INPUT_PULLUP | MUX_MODE0) /* sys_nirq.sys_nirq */
+		>;
+	};
+};
+
+&tps {
+	pinctrl-names = "default";
+	pinctrl-0 = <&tps_pins>;
+
+	interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+	interrupt-parent = <&intc>;
+
+	ti,en-ck32k-xtal;
+
+	vcc1-supply = <&vbat>;
+	vcc2-supply = <&vbat>;
+	vcc3-supply = <&vbat>;
+	vcc4-supply = <&vbat>;
+	vcc5-supply = <&vbat>;
+	vcc6-supply = <&vbat>;
+	vcc7-supply = <&vbat>;
+	vccio-supply = <&vbat>;
+
+	regulators {
+		vrtc_reg: regulator@0 {
+			regulator-always-on;
+		};
+
+		vio_reg: regulator@1 {
+			regulator-always-on;
+		};
+
+		/*
+		 * Unused:
+		 * VDIG1=2.7V,300mA max
+		 * VDIG2=1.8V,300mA max
+		 */
+
+		vpll_reg: regulator@7 {
+			/* VDDS_DPLL_1V8 */
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		vaux1_reg: regulator@9 {
+			/* VDDS_SRAM_1V8 */
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		vaux2_reg: regulator@10 {
+			/* VDDA1P8V_USBPHY */
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		/* VAUX33 unused */
+
+		vdac_reg: regulator@8 {
+			/* VDDA_DAC_1V8 */
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		vmmc_reg: regulator@12 {
+			/* VDDA3P3V_USBPHY */
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		vdd1_reg: regulator@2 {
+			/* VDD_CORE */
+			regulator-name = "vdd_core";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		vdd2_reg: regulator@3 {
+			/* VDDSHV_3V3 */
+			regulator-name = "vdd_shv";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		/* VDD3 unused */
+	};
+};

arch/arm/boot/dts/am4372.dtsi

@@ -33,6 +33,11 @@ cpu@0 {
 			compatible = "arm,cortex-a9";
 			device_type = "cpu";
 			reg = <0>;
+
+			clocks = <&dpll_mpu_ck>;
+			clock-names = "cpu";
+
+			clock-latency = <300000>; /* From omap-cpufreq driver */
 		};
 	};
 
@@ -351,6 +356,13 @@ gpio5: gpio@48322000 {
 			status = "disabled";
 		};
 
+		hwspinlock: spinlock@480ca000 {
+			compatible = "ti,omap4-hwspinlock";
+			reg = <0x480ca000 0x1000>;
+			ti,hwmods = "spinlock";
+			#hwlock-cells = <1>;
+		};
+
 		i2c0: i2c@44e0b000 {
 			compatible = "ti,am4372-i2c","ti,omap4-i2c";
 			reg = <0x44e0b000 0x1000>;
@@ -521,6 +533,7 @@ epwmss0: epwmss@48300000 {
 
 			ecap0: ecap@48300100 {
 				compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+				#pwm-cells = <3>;
 				reg = <0x48300100 0x80>;
 				ti,hwmods = "ecap0";
 				status = "disabled";
@@ -528,6 +541,7 @@ ecap0: ecap@48300100 {
 
 			ehrpwm0: ehrpwm@48300200 {
 				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				#pwm-cells = <3>;
 				reg = <0x48300200 0x80>;
 				ti,hwmods = "ehrpwm0";
 				status = "disabled";
@@ -545,6 +559,7 @@ epwmss1: epwmss@48302000 {
 
 			ecap1: ecap@48302100 {
 				compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+				#pwm-cells = <3>;
 				reg = <0x48302100 0x80>;
 				ti,hwmods = "ecap1";
 				status = "disabled";
@@ -552,6 +567,7 @@ ecap1: ecap@48302100 {
 
 			ehrpwm1: ehrpwm@48302200 {
 				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				#pwm-cells = <3>;
 				reg = <0x48302200 0x80>;
 				ti,hwmods = "ehrpwm1";
 				status = "disabled";
@@ -569,6 +585,7 @@ epwmss2: epwmss@48304000 {
 
 			ecap2: ecap@48304100 {
 				compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+				#pwm-cells = <3>;
 				reg = <0x48304100 0x80>;
 				ti,hwmods = "ecap2";
 				status = "disabled";
@@ -576,6 +593,7 @@ ecap2: ecap@48304100 {
 
 			ehrpwm2: ehrpwm@48304200 {
 				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				#pwm-cells = <3>;
 				reg = <0x48304200 0x80>;
 				ti,hwmods = "ehrpwm2";
 				status = "disabled";
@@ -593,6 +611,7 @@ epwmss3: epwmss@48306000 {
 
 			ehrpwm3: ehrpwm@48306200 {
 				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				#pwm-cells = <3>;
 				reg = <0x48306200 0x80>;
 				ti,hwmods = "ehrpwm3";
 				status = "disabled";
@@ -610,6 +629,7 @@ epwmss4: epwmss@48308000 {
 
 			ehrpwm4: ehrpwm@48308200 {
 				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				#pwm-cells = <3>;
 				reg = <0x48308200 0x80>;
 				ti,hwmods = "ehrpwm4";
 				status = "disabled";
@@ -627,6 +647,7 @@ epwmss5: epwmss@4830a000 {
 
 			ehrpwm5: ehrpwm@4830a200 {
 				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				#pwm-cells = <3>;
 				reg = <0x4830a200 0x80>;
 				ti,hwmods = "ehrpwm5";
 				status = "disabled";
@@ -689,6 +710,30 @@ mcasp1: mcasp@4803C000 {
 			       <&edma 11>;
 			dma-names = "tx", "rx";
 		};
+
+		elm: elm@48080000 {
+			compatible = "ti,am3352-elm";
+			reg = <0x48080000 0x2000>;
+			interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "elm";
+			clocks = <&l4ls_gclk>;
+			clock-names = "fck";
+			status = "disabled";
+		};
+
+		gpmc: gpmc@50000000 {
+			compatible = "ti,am3352-gpmc";
+			ti,hwmods = "gpmc";
+			clocks = <&l3s_gclk>;
+			clock-names = "fck";
+			reg = <0x50000000 0x2000>;
+			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+			gpmc,num-cs = <7>;
+			gpmc,num-waitpins = <2>;
+			#address-cells = <2>;
+			#size-cells = <1>;
+			status = "disabled";
+		};
 	};
 };
 

arch/arm/boot/dts/am437x-gp-evm.dts

+/*
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/* AM437x GP EVM */
+
+/dts-v1/;
+
+#include "am4372.dtsi"
+#include <dt-bindings/pinctrl/am43xx.h>
+#include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "TI AM437x GP EVM";
+	compatible = "ti,am437x-gp-evm","ti,am4372","ti,am43";
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&ecap0 0 50000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 51 53 56 62 75 101 152 255>;
+		default-brightness-level = <8>;
+	};
+
+	matrix_keypad: matrix_keypad@0 {
+		compatible = "gpio-matrix-keypad";
+		debounce-delay-ms = <5>;
+		col-scan-delay-us = <2>;
+
+		row-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH /* Bank3, pin21 */
+				&gpio4 3 GPIO_ACTIVE_HIGH /* Bank4, pin3 */
+				&gpio4 2 GPIO_ACTIVE_HIGH>; /* Bank4, pin2 */
+
+		col-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH /* Bank3, pin19 */
+				&gpio3 20 GPIO_ACTIVE_HIGH>; /* Bank3, pin20 */
+
+		linux,keymap = <0x00000201      /* P1 */
+				0x00010202      /* P2 */
+				0x01000067      /* UP */
+				0x0101006a      /* RIGHT */
+				0x02000069      /* LEFT */
+				0x0201006c>;      /* DOWN */
+		};
+};
+
+&am43xx_pinmux {
+	i2c0_pins: i2c0_pins {
+		pinctrl-single,pins = <
+			0x188 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)  /* i2c0_sda.i2c0_sda */
+			0x18c (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)  /* i2c0_scl.i2c0_scl */
+		>;
+	};
+
+	i2c1_pins: i2c1_pins {
+		pinctrl-single,pins = <
+			0x15c (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE2)  /* spi0_cs0.i2c1_scl */
+			0x158 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE2)  /* spi0_d1.i2c1_sda  */
+		>;
+	};
+
+	ecap0_pins: backlight_pins {
+		pinctrl-single,pins = <
+			0x164 MUX_MODE0       /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */
+		>;
+	};
+};
+
+&i2c0 {
+        status = "okay";
+        pinctrl-names = "default";
+        pinctrl-0 = <&i2c0_pins>;
+};
+
+&i2c1 {
+        status = "okay";
+        pinctrl-names = "default";
+        pinctrl-0 = <&i2c1_pins>;
+};
+
+&epwmss0 {
+	status = "okay";
+};
+
+&ecap0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&ecap0_pins>;
+};
+
+&gpio3 {
+	status = "okay";
+};
+
+&gpio4 {
+	status = "okay";
+};

arch/arm/boot/dts/am43x-epos-evm.dts

@@ -13,6 +13,7 @@
 #include "am4372.dtsi"
 #include <dt-bindings/pinctrl/am43xx.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pwm/pwm.h>
 
 / {
 	model = "TI AM43x EPOS EVM";
@@ -79,6 +80,58 @@ i2c0_pins: pinmux_i2c0_pins {
 				0x18c (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)	/* i2c0_scl.i2c0_scl */
 			>;
 		};
+
+		nand_flash_x8: nand_flash_x8 {
+			pinctrl-single,pins = <
+				0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a0.SELQSPIorNAND/GPIO */
+				0x0  (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad0.gpmc_ad0 */
+				0x4  (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad1.gpmc_ad1 */
+				0x8  (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad2.gpmc_ad2 */
+				0xc  (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad3.gpmc_ad3 */
+				0x10 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad4.gpmc_ad4 */
+				0x14 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad5.gpmc_ad5 */
+				0x18 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad6.gpmc_ad6 */
+				0x1c (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad7.gpmc_ad7 */
+				0x70 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_wait0.gpmc_wait0 */
+				0x74 (PIN_OUTPUT_PULLUP | MUX_MODE7)	/* gpmc_wpn.gpmc_wpn */
+				0x7c (PIN_OUTPUT | MUX_MODE0)		/* gpmc_csn0.gpmc_csn0  */
+				0x90 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_advn_ale.gpmc_advn_ale */
+				0x94 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_oen_ren.gpmc_oen_ren */
+				0x98 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_wen.gpmc_wen */
+				0x9c (PIN_OUTPUT | MUX_MODE0)		/* gpmc_be0n_cle.gpmc_be0n_cle */
+			>;
+		};
+
+		ecap0_pins: backlight_pins {
+			pinctrl-single,pins = <
+				0x164 MUX_MODE0         /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */
+			>;
+		};
+
+		i2c2_pins: pinmux_i2c2_pins {
+			pinctrl-single,pins = <
+				0x1c0 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE8)    /* i2c2_sda.i2c2_sda */
+				0x1c4 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE8)    /* i2c2_scl.i2c2_scl */
+			>;
+		};
+
+		spi0_pins: pinmux_spi0_pins {
+			pinctrl-single,pins = <
+				0x150 (PIN_INPUT | MUX_MODE0)           /* spi0_clk.spi0_clk */
+				0x154 (PIN_OUTPUT | MUX_MODE0)           /* spi0_d0.spi0_d0 */
+				0x158 (PIN_INPUT | MUX_MODE0)           /* spi0_d1.spi0_d1 */
+				0x15c (PIN_OUTPUT | MUX_MODE0)          /* spi0_cs0.spi0_cs0 */
+			>;
+		};
+
+		spi1_pins: pinmux_spi1_pins {
+			pinctrl-single,pins = <
+				0x190 (PIN_INPUT | MUX_MODE3)           /* mcasp0_aclkx.spi1_clk */
+				0x194 (PIN_OUTPUT | MUX_MODE3)           /* mcasp0_fsx.spi1_d0 */
+				0x198 (PIN_INPUT | MUX_MODE3)           /* mcasp0_axr0.spi1_d1 */
+				0x19c (PIN_OUTPUT | MUX_MODE3)          /* mcasp0_ahclkr.spi1_cs0 */
+			>;
+		};
 	};
 
 	matrix_keypad: matrix_keypad@0 {
@@ -113,6 +166,13 @@ &gpio2 18 GPIO_ACTIVE_HIGH		/* Bank2, pin18 */
 				0x0203006c	/* DOWN */
 				0x03030069>;	/* LEFT */
 		};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&ecap0 0 50000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 51 53 56 62 75 101 152 255>;
+		default-brightness-level = <8>;
+	};
 };
 
 &mmc1 {
@@ -169,6 +229,12 @@ pixcir_ts@5c {
 	};
 };
 
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
+	status = "okay";
+};
+
 &gpio0 {
 	status = "okay";
 };
@@ -184,3 +250,111 @@ &gpio2 {
 &gpio3 {
 	status = "okay";
 };
+
+&elm {
+	status = "okay";
+};
+
+&gpmc {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&nand_flash_x8>;
+	ranges = <0 0 0x08000000 0x10000000>;	/* CS0: NAND */
+	nand@0,0 {
+		reg = <0 0 0>; /* CS0, offset 0 */
+		ti,nand-ecc-opt = "bch8";
+		ti,elm-id = <&elm>;
+		nand-bus-width = <8>;
+		gpmc,device-width = <1>;
+		gpmc,sync-clk-ps = <0>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <40>; /* tCEA + tCHZ + 1 */
+		gpmc,cs-wr-off-ns = <40>;
+		gpmc,adv-on-ns = <0>;  /* cs-on-ns */
+		gpmc,adv-rd-off-ns = <25>; /* min( tALH + tALS + 1) */
+		gpmc,adv-wr-off-ns = <25>; /* min( tALH + tALS + 1) */
+		gpmc,we-on-ns = <0>;   /* cs-on-ns */
+		gpmc,we-off-ns = <20>; /* we-on-time + tWP + 2 */
+		gpmc,oe-on-ns = <3>;  /* cs-on-ns + tRR + 2 */
+		gpmc,oe-off-ns = <30>; /* oe-on-ns + tRP + 2 */
+		gpmc,access-ns = <30>; /* tCEA + 4*/
+		gpmc,rd-cycle-ns = <40>;
+		gpmc,wr-cycle-ns = <40>;
+		gpmc,wait-on-read = "true";
+		gpmc,wait-on-write = "true";
+		gpmc,bus-turnaround-ns = <0>;
+		gpmc,cycle2cycle-delay-ns = <0>;
+		gpmc,clk-activation-ns = <0>;
+		gpmc,wait-monitoring-ns = <0>;
+		gpmc,wr-access-ns = <40>;
+		gpmc,wr-data-mux-bus-ns = <0>;
+		/* MTD partition table */
+		/* All SPL-* partitions are sized to minimal length
+		 * which can be independently programmable. For
+		 * NAND flash this is equal to size of erase-block */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		partition@0 {
+			label = "NAND.SPL";
+			reg = <0x00000000 0x00040000>;
+		};
+		partition@1 {
+			label = "NAND.SPL.backup1";
+			reg = <0x00040000 0x00040000>;
+		};
+		partition@2 {
+			label = "NAND.SPL.backup2";
+			reg = <0x00080000 0x00040000>;
+		};
+		partition@3 {
+			label = "NAND.SPL.backup3";
+			reg = <0x000C0000 0x00040000>;
+		};
+		partition@4 {
+			label = "NAND.u-boot-spl-os";
+			reg = <0x00100000 0x00080000>;
+		};
+		partition@5 {
+			label = "NAND.u-boot";
+			reg = <0x00180000 0x00100000>;
+		};
+		partition@6 {
+			label = "NAND.u-boot-env";
+			reg = <0x00280000 0x00040000>;
+		};
+		partition@7 {
+			label = "NAND.u-boot-env.backup1";
+			reg = <0x002C0000 0x00040000>;
+		};
+		partition@8 {
+			label = "NAND.kernel";
+			reg = <0x00300000 0x00700000>;
+		};
+		partition@9 {
+			label = "NAND.file-system";
+			reg = <0x00800000 0x1F600000>;
+		};
+	};
+};
+
+&epwmss0 {
+	status = "okay";
+};
+
+&ecap0 {
+		status = "okay";
+		pinctrl-names = "default";
+		pinctrl-0 = <&ecap0_pins>;
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins>;
+	status = "okay";
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi1_pins>;
+	status = "okay";
+};

arch/arm/boot/dts/dra7.dtsi

@@ -47,6 +47,11 @@ cpu0: cpu@0 {
 				1000000	1060000
 				1176000	1160000
 				>;
+
+			clocks = <&dpll_mpu_ck>;
+			clock-names = "cpu";
+
+			clock-latency = <300000>; /* From omap-cpufreq driver */
 		};
 		cpu@1 {
 			device_type = "cpu";
@@ -464,6 +469,20 @@ wdt2: wdt@4ae14000 {
 			ti,hwmods = "wd_timer2";
 		};
 
+		hwspinlock: spinlock@4a0f6000 {
+			compatible = "ti,omap4-hwspinlock";
+			reg = <0x4a0f6000 0x1000>;
+			ti,hwmods = "spinlock";
+			#hwlock-cells = <1>;
+		};
+
+		dmm@4e000000 {
+			compatible = "ti,omap5-dmm";
+			reg = <0x4e000000 0x800>;
+			interrupts = <0 113 0x4>;
+			ti,hwmods = "dmm";
+		};
+
 		i2c1: i2c@48070000 {
 			compatible = "ti,omap4-i2c";
 			reg = <0x48070000 0x100>;

arch/arm/boot/dts/omap2420.dtsi

@@ -99,6 +99,7 @@ mcbsp1: mcbsp@48074000 {
 			dmas = <&sdma 31>,
 			       <&sdma 32>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		mcbsp2: mcbsp@48076000 {
@@ -112,6 +113,7 @@ mcbsp2: mcbsp@48076000 {
 			dmas = <&sdma 33>,
 			       <&sdma 34>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		msdi1: mmc@4809c000 {

arch/arm/boot/dts/omap2430.dtsi

@@ -113,6 +113,7 @@ mcbsp1: mcbsp@48074000 {
 			dmas = <&sdma 31>,
 			       <&sdma 32>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		mcbsp2: mcbsp@48076000 {
@@ -128,6 +129,7 @@ mcbsp2: mcbsp@48076000 {
 			dmas = <&sdma 33>,
 			       <&sdma 34>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		mcbsp3: mcbsp@4808c000 {
@@ -143,6 +145,7 @@ mcbsp3: mcbsp@4808c000 {
 			dmas = <&sdma 17>,
 			       <&sdma 18>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		mcbsp4: mcbsp@4808e000 {
@@ -158,6 +161,7 @@ mcbsp4: mcbsp@4808e000 {
 			dmas = <&sdma 19>,
 			       <&sdma 20>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		mcbsp5: mcbsp@48096000 {
@@ -173,6 +177,7 @@ mcbsp5: mcbsp@48096000 {
 			dmas = <&sdma 21>,
 			       <&sdma 22>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		mmc1: mmc@4809c000 {

arch/arm/boot/dts/omap3-beagle-xm.dts

@@ -234,3 +234,7 @@ &vaux2 {
 	regulator-max-microvolt = <1800000>;
 	regulator-always-on;
 };
+
+&mcbsp2 {
+	status = "okay";
+};

arch/arm/boot/dts/omap3-beagle.dts

@@ -211,3 +211,7 @@ &vaux2 {
 	regulator-max-microvolt = <1800000>;
 	regulator-always-on;
 };
+
+&mcbsp2 {
+	status = "okay";
+};

arch/arm/boot/dts/omap3-cm-t3517.dts

+/*
+ * Support for CompuLab CM-T3517
+ */
+/dts-v1/;
+
+#include "am3517.dtsi"
+#include "omap3-cm-t3x.dtsi"
+
+/ {
+	model = "CompuLab CM-T3517";
+	compatible = "compulab,omap3-cm-t3517", "ti,am3517", "ti,omap3";
+
+	vmmc:  regulator-vmmc {
+                compatible = "regulator-fixed";
+                regulator-name = "vmmc";
+                regulator-min-microvolt = <3300000>;
+                regulator-max-microvolt = <3300000>;
+        };
+
+	wl12xx_vmmc2: wl12xx_vmmc2 {
+		compatible = "regulator-fixed";
+		regulator-name = "vw1271";
+		pinctrl-names = "default";
+		pinctrl-0 = <
+				&wl12xx_wkup_pins
+				&wl12xx_core_pins
+			    >;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio1 6 GPIO_ACTIVE_HIGH >; /* gpio6 */
+		startup-delay-us = <20000>;
+		enable-active-high;
+	};
+
+	wl12xx_vaux2: wl12xx_vaux2 {
+		compatible = "regulator-fixed";
+		regulator-name = "vwl1271_vaux2";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+};
+
+&omap3_pmx_wkup {
+
+	wl12xx_wkup_pins: pinmux_wl12xx_wkup_pins {
+		pinctrl-single,pins = <
+			OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4)	/* sys_boot2.gpio_4 */
+			OMAP3_WKUP_IOPAD(0x2a12, PIN_OUTPUT | MUX_MODE4)	/* sys_boot4.gpio_6 */
+		>;
+	};
+};
+
+&omap3_pmx_core {
+
+	phy1_reset_pins: pinmux_hsusb1_phy_reset_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE4)	/* uart2_tx.gpio_146 */
+		>;
+	};
+
+	phy2_reset_pins: pinmux_hsusb2_phy_reset_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x217a, PIN_OUTPUT | MUX_MODE4)	/* uart2_rx.gpio_147 */
+		>;
+	};
+
+	otg_drv_vbus: pinmux_otg_drv_vbus {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2210, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_50Mhz_clk.usb0_drvvbus */
+		>;
+	};
+
+	mmc2_pins: pinmux_mmc2_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_clk.sdmmc2_clk */
+			OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_cmd.sdmmc2_cmd */
+			OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat0.sdmmc2_dat0 */
+			OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat1.sdmmc2_dat1 */
+			OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat2.sdmmc2_dat2 */
+			OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat3.sdmmc2_dat3 */
+		>;
+	};
+
+	wl12xx_core_pins: pinmux_wl12xx_core_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x20b8, PIN_OUTPUT | MUX_MODE4)	/* gpmc_ncs5.gpio_56 */
+			OMAP3_CORE1_IOPAD(0x2176, PIN_INPUT_PULLUP | MUX_MODE4)	/* uart2_rts.gpio_145 */
+		>;
+	};
+
+	usb_hub_pins: pinmux_usb_hub_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2184, PIN_OUTPUT | MUX_MODE4)	/* mcbsp4_clkx.gpio_152 - USB HUB RST */
+		>;
+	};
+};
+
+&hsusb1_phy {
+	pinctrl-names = "default";
+	pinctrl-0 = <&phy1_reset_pins>;
+	reset-gpios = <&gpio5 18 GPIO_ACTIVE_LOW>;
+};
+
+&hsusb2_phy {
+	pinctrl-names = "default";
+	pinctrl-0 = <&phy2_reset_pins>;
+	reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>;
+};
+
+&davinci_emac {
+	status = "okay";
+};
+
+&davinci_mdio {
+	status = "okay";
+};
+
+&am35x_otg_hs {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&otg_drv_vbus>;
+};
+
+&mmc1 {
+	vmmc-supply = <&vmmc>;
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins>;
+	vmmc-supply = <&wl12xx_vmmc2>;
+	vmmc_aux-supply = <&wl12xx_vaux2>;
+	non-removable;
+	bus-width = <4>;
+	cap-power-off-card;
+};

arch/arm/boot/dts/omap3-cm-t3530.dts

+/*
+ * Support for CompuLab CM-T3530
+ */
+/dts-v1/;
+
+#include "omap34xx.dtsi"
+#include "omap3-cm-t3x30.dtsi"
+
+/ {
+	model = "CompuLab CM-T3530";
+	compatible = "compulab,omap3-cm-t3530", "ti,omap34xx", "ti,omap3";
+};

arch/arm/boot/dts/omap3-cm-t3730.dts

@@ -32,57 +32,26 @@ wl12xx_vaux2: wl12xx_vaux2 {
 };
 
 &omap3_pmx_core {
-	mmc1_pins: pinmux_mmc1_pins {
-		pinctrl-single,pins = <
-			0x114 (PIN_OUTPUT_PULLUP | MUX_MODE0)	/* sdmmc1_clk.sdmmc1_clk */
-			0x116 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_cmd.sdmmc1_cmd */
-			0x118 (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc1_dat0.sdmmc1_dat0 */
-			0x11a (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc1_dat1.sdmmc1_dat1 */
-			0x11c (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc1_dat2.sdmmc1_dat2 */
-			0x11e (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc1_dat3.sdmmc1_dat3 */
-		>;
-	};
 
 	mmc2_pins: pinmux_mmc2_pins {
 		pinctrl-single,pins = <
-			0x128 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_clk.sdmmc2_clk */
-			0x12a (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_cmd.sdmmc2_cmd */
-			0x12c (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat0.sdmmc2_dat0 */
-			0x12e (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat1.sdmmc2_dat1 */
-			0x130 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat2.sdmmc2_dat2 */
-			0x132 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat3.sdmmc2_dat3 */
-		>;
-	};
-
-	smsc1_pins: pinmux_smsc1_pins {
-		pinctrl-single,pins = <
-			0x88 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_ncs5.gpmc_ncs5 */
-			0x16a (PIN_INPUT_PULLUP | MUX_MODE4)	/* uart3_cts_rctx.gpio_163 */
-		>;
-	};
-
-	uart3_pins: pinmux_uart3_pins {
-		pinctrl-single,pins = <
-			0x16e (PIN_INPUT | MUX_MODE0)		/* uart3_rx_irrx.uart3_rx_irrx */
-			0x170 (PIN_OUTPUT | MUX_MODE0)		/* uart3_tx_irtx.uart3_tx_irtx */
+			OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_clk.sdmmc2_clk */
+			OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_cmd.sdmmc2_cmd */
+			OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat0.sdmmc2_dat0 */
+			OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat1.sdmmc2_dat1 */
+			OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat2.sdmmc2_dat2 */
+			OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat3.sdmmc2_dat3 */
 		>;
 	};
 
 	wl12xx_gpio: pinmux_wl12xx_gpio {
 		pinctrl-single,pins = <
-			0xb2 (PIN_OUTPUT | MUX_MODE4)		/* dss_data3.gpio_73 */
-			0x134 (PIN_INPUT | MUX_MODE4)		/* sdmmc2_dat4.gpio_136 */
+			OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE4)	/* dss_data3.gpio_73 */
+			OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT | MUX_MODE4)	/* sdmmc2_dat4.gpio_136 */
 		>;
 	};
 };
 
-&mmc1 {
-	vmmc-supply = <&vmmc1>;
-	bus-width = <4>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc1_pins>;
-};
-
 &mmc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc2_pins>;
@@ -92,13 +61,3 @@ &mmc2 {
 	bus-width = <4>;
 	cap-power-off-card;
 };
-
-&smsc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&smsc1_pins>;
-};
-
-&uart3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart3_pins>;
-};

arch/arm/boot/dts/omap3-cm-t3x.dtsi

+/*
+ * Common support for CompuLab CM-T3x CoMs
+ */
+
+/ {
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>; /* 256 MB */
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&green_led_pins>;
+		ledb {
+			label = "cm-t3x:green";
+			gpios = <&gpio6 26 GPIO_ACTIVE_HIGH>;  /* gpio186 */
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	/* HS USB Port 1 Power */
+	hsusb1_power: hsusb1_power_reg {
+		compatible = "regulator-fixed";
+		regulator-name = "hsusb1_vbus";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <70000>;
+	};
+
+	/* HS USB Port 2 Power */
+	hsusb2_power: hsusb2_power_reg {
+		compatible = "regulator-fixed";
+		regulator-name = "hsusb2_vbus";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <70000>;
+	};
+
+	/* HS USB Host PHY on PORT 1 */
+	hsusb1_phy: hsusb1_phy {
+		compatible = "usb-nop-xceiv";
+		vcc-supply = <&hsusb1_power>;
+	};
+
+	/* HS USB Host PHY on PORT 2 */
+	hsusb2_phy: hsusb2_phy {
+		compatible = "usb-nop-xceiv";
+		vcc-supply = <&hsusb2_power>;
+	};
+};
+
+&omap3_pmx_core {
+
+	uart3_pins: pinmux_uart3_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT  | MUX_MODE0)	/* uart3_rx_irrx.uart3_rx_irrx */
+			OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0)	/* uart3_tx_irtx.uart3_tx_irtx */
+		>;
+	};
+
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_clk.sdmmc1_clk */
+			OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_cmd.sdmmc1_cmd */
+			OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_dat0.sdmmc1_dat0 */
+			OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_dat1.sdmmc1_dat1 */
+			OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_dat2.sdmmc1_dat2 */
+			OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_dat3.sdmmc1_dat3 */
+		>;
+	};
+
+	green_led_pins: pinmux_green_led_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21e2, PIN_OUTPUT | MUX_MODE4)	/* sys_clkout2.gpio_186 */
+		>;
+	};
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	bus-width = <4>;
+};
+
+&mmc3 {
+	status = "disabled";
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+};
+
+&i2c3 {
+	clock-frequency = <400000>;
+};
+&usbhshost {
+	port1-mode = "ehci-phy";
+	port2-mode = "ehci-phy";
+};
+
+&usbhsehci {
+	phys = <&hsusb1_phy &hsusb2_phy>;
+};

arch/arm/boot/dts/omap3-cm-t3x30.dtsi

 /*
- * Common support for CompuLab CM-T3530 and  CM-T3730
+ * Common support for CompuLab CM-T3x30 CoMs
  */
 
-/ {
-	memory {
-		device_type = "memory";
-		reg = <0x80000000 0x10000000>; /* 256 MB */
-	};
+#include "omap3-cm-t3x.dtsi"
 
+/ {
 	cpus {
 		cpu@0 {
 			cpu0-supply = <&vcc>;
 		};
 	};
 
-	leds {
-		compatible = "gpio-leds";
-		ledb {
-			label = "cm-t35:green";
-			gpios = <&gpio6 26 GPIO_ACTIVE_HIGH>;  /* gpio186 */
-			linux,default-trigger = "heartbeat";
-		};
-	};
-
 	vddvario: regulator-vddvario {
 		compatible = "regulator-fixed";
 		regulator-name = "vddvario";
@@ -36,11 +24,40 @@ vdd33a: regulator-vdd33a {
 	};
 };
 
+&omap3_pmx_core {
+
+	smsc1_pins: pinmux_smsc1_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x20b8, PIN_OUTPUT | MUX_MODE0)	/* gpmc_ncs5.gpmc_ncs5 */
+			OMAP3_CORE1_IOPAD(0x219a, PIN_INPUT_PULLUP | MUX_MODE4)	/* uart3_cts_rctx.gpio_163 */
+		>;
+	};
+
+ 	hsusb0_pins: pinmux_hsusb0_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0)		/* hsusb0_clk.hsusb0_clk */
+			OMAP3_CORE1_IOPAD(0x21a2, PIN_OUTPUT | MUX_MODE0)		/* hsusb0_stp.hsusb0_stp */
+			OMAP3_CORE1_IOPAD(0x21a4, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_dir.hsusb0_dir */
+			OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_nxt.hsusb0_nxt */
+			OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data0.hsusb2_data0 */
+			OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data1.hsusb0_data1 */
+			OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data2.hsusb0_data2 */
+			OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data3 */
+			OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data4 */
+			OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data5 */
+			OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data6 */
+			OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data7 */
+		>;
+	};
+};
+
 &gpmc {
 	ranges = <5 0 0x2c000000 0x01000000>;
 
 	smsc1: ethernet@5,0 {
 		compatible = "smsc,lan9221", "smsc,lan9115";
+		pinctrl-names = "default";
+		pinctrl-0 = <&smsc1_pins>;
 		interrupt-parent = <&gpio6>;
 		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
 		reg = <5 0 0xff>;
@@ -74,8 +91,6 @@ smsc1: ethernet@5,0 {
 };
 
 &i2c1 {
-	clock-frequency = <400000>;
-
 	twl: twl@48 {
 		reg = <0x48>;
 		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
@@ -86,10 +101,31 @@ twl: twl@48 {
 #include "twl4030.dtsi"
 #include "twl4030_omap3.dtsi"
 
-&i2c3 {
-	clock-frequency = <400000>;
+&mmc1 {
+	vmmc-supply = <&vmmc1>;
 };
 
 &twl_gpio {
 	ti,use-leds;
+	/* pullups: BIT(0) */
+	ti,pullups = <0x000001>;
+};
+
+&hsusb1_phy {
+	reset-gpios = <&twl_gpio 6 GPIO_ACTIVE_LOW>;
+};
+
+&hsusb2_phy {
+	reset-gpios = <&twl_gpio 7 GPIO_ACTIVE_LOW>;
+};
+
+&usb_otg_hs {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hsusb0_pins>;
+	interface-type = <0>;
+	usb-phy = <&usb2_phy>;
+	phys = <&usb2_phy>;
+	phy-names = "usb2-phy";
+	mode = <3>;
+	power = <50>;
 };

arch/arm/boot/dts/omap3-devkit8000.dts

@@ -101,20 +101,8 @@ &wdt2 {
 	status = "disabled";
 };
 
-&mcbsp1 {
-	status = "disabled";
-};
-
-&mcbsp3 {
-	status = "disabled";
-};
-
-&mcbsp4 {
-	status = "disabled";
-};
-
-&mcbsp5 {
-	status = "disabled";
+&mcbsp2 {
+	status = "okay";
 };
 
 &gpmc {

arch/arm/boot/dts/omap3-gta04.dts

@@ -36,6 +36,14 @@ aux-button {
 			gpio-key,wakeup;
 		};
 	};
+
+	sound {
+		compatible = "ti,omap-twl4030";
+		ti,model = "gta04";
+
+		ti,mcbsp = <&mcbsp2>;
+		ti,codec = <&twl_audio>;
+	};
 };
 
 &omap3_pmx_core {
@@ -80,6 +88,12 @@ twl: twl@48 {
 		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
 		interrupt-parent = <&intc>;
 	};
+
+	twl_audio: audio {
+		compatible = "ti,twl4030-audio";
+		codec {
+		};
+	};
 };
 
 #include "twl4030.dtsi"
@@ -94,6 +108,14 @@ bmp085@77 {
 		reg = <0x77>;
 	};
 
+	/* accelerometer */
+	bma180@41 {
+		compatible = "bosch,bma180";
+		reg = <0x41>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <19 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
 	/* leds */
 	tca6507@45 {
 		compatible = "ti,tca6507";
@@ -122,6 +144,22 @@ gta04_led4: green_power@4 {
 			reg = <0x4>;
 		};
 	};
+
+	/* compass aka magnetometer */
+	hmc5843@1e {
+		compatible = "honeywell,hmc5843";
+		reg = <0x1e>;
+	};
+
+	/* touchscreen */
+	tsc2007@48 {
+		compatible = "ti,tsc2007";
+		reg = <0x48>;
+		interrupt-parent = <&gpio6>;
+		interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+		gpios = <&gpio6 0 GPIO_ACTIVE_LOW>;
+		ti,x-plate-ohms = <600>;
+	};
 };
 
 &i2c3 {
@@ -146,7 +184,9 @@ &mmc1 {
 };
 
 &mmc2 {
-	status = "disabled";
+	vmmc-supply = <&vaux4>;
+	bus-width = <4>;
+	ti,non-removable;
 };
 
 &mmc3 {
@@ -168,3 +208,12 @@ &uart3 {
 	pinctrl-0 = <&uart3_pins>;
 };
 
+&charger {
+	bb_uvolt = <3200000>;
+	bb_uamp = <150>;
+};
+
+&vaux4 {
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <3150000>;
+};

arch/arm/boot/dts/omap3-igep.dtsi

@@ -170,6 +170,7 @@ &i2c3 {
 &mcbsp2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcbsp2_pins>;
+	status = "okay";
 };
 
 &mmc1 {

arch/arm/boot/dts/omap3-lilly-dbb056.dts

+/*
+ * Copyright (C) 2014 Christoph Fritz <chf.fritzc@googlemail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+/dts-v1/;
+
+#include "omap3-lilly-a83x.dtsi"
+
+/ {
+	model = "INCOstartec LILLY-DBB056 (DM3730)";
+	compatible = "incostartec,omap3-lilly-dbb056", "incostartec,omap3-lilly-a83x", "ti,omap36xx", "ti,omap3";
+};
+
+&twl {
+	vaux2: regulator-vaux2 {
+		compatible = "ti,twl4030-vaux2";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		regulator-always-on;
+	};
+};
+
+&omap3_pmx_core {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcd_pins>;
+
+	lan9117_pins: pinmux_lan9117_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2114, PIN_INPUT | MUX_MODE4)   /* cam_fld.gpio_98 */
+		>;
+	};
+
+	gpio4_pins: pinmux_gpio4_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x212e, PIN_INPUT | MUX_MODE4)   /* cam_xclkb.gpio_111 -> sja1000 IRQ */
+		>;
+	};
+
+	gpio5_pins: pinmux_gpio5_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x218c, PIN_OUTPUT | PIN_OFF_OUTPUT_HIGH | MUX_MODE4)   /* mcbsp1_clk.gpio_156 -> enable DSS */
+		>;
+	};
+
+	lcd_pins: pinmux_lcd_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0)   /* dss_pclk.dss_pclk */
+			OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0)   /* dss_hsync.dss_hsync */
+			OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0)   /* dss_vsync.dss_vsync */
+			OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0)   /* dss_acbias.dss_acbias */
+			OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE0)   /* dss_data0.dss_data0 */
+			OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT | MUX_MODE0)   /* dss_data1.dss_data1 */
+			OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT | MUX_MODE0)   /* dss_data2.dss_data2 */
+			OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE0)   /* dss_data3.dss_data3 */
+			OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE0)   /* dss_data4.dss_data4 */
+			OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE0)   /* dss_data5.dss_data5 */
+			OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0)   /* dss_data6.dss_data6 */
+			OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0)   /* dss_data7.dss_data7 */
+			OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0)   /* dss_data8.dss_data8 */
+			OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0)   /* dss_data9.dss_data9 */
+			OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0)   /* dss_data10.dss_data10 */
+			OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0)   /* dss_data11.dss_data11 */
+			OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0)   /* dss_data12.dss_data12 */
+			OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0)   /* dss_data13.dss_data13 */
+			OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0)   /* dss_data14.dss_data14 */
+			OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0)   /* dss_data15.dss_data15 */
+			OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0)   /* dss_data16.dss_data16 */
+			OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0)   /* dss_data17.dss_data17 */
+		>;
+	};
+
+	mmc2_pins: pinmux_mmc2_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)   /* sdmmc2_clk.sdmmc2_clk */
+			OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0)   /* sdmmc2_cmd.sdmmc2_cmd */
+			OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0)   /* sdmmc2_dat0.sdmmc2_dat0 */
+			OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0)   /* sdmmc2_dat1.sdmmc2_dat1 */
+			OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0)   /* sdmmc2_dat2.sdmmc2_dat2 */
+			OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0)   /* sdmmc2_dat3.sdmmc2_dat3 */
+			OMAP3_CORE1_IOPAD(0x2164, PIN_OUTPUT | MUX_MODE1)   /* sdmmc2_dat4.sdmmc2_dir_dat0 */
+			OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT | MUX_MODE1)   /* sdmmc2_dat5.sdmmc2_dir_dat1 */
+			OMAP3_CORE1_IOPAD(0x2168, PIN_OUTPUT | MUX_MODE1)   /* sdmmc2_dat6.sdmmc2_dir_cmd */
+			OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT | MUX_MODE1)    /* sdmmc2_dat7.sdmmc2_clkin */
+			OMAP3_CORE1_IOPAD(0x219a, PIN_INPUT_PULLUP | MUX_MODE4)   /* uart3_cts_rctx.gpio_163 -> wp */
+			OMAP3_CORE1_IOPAD(0x219c, PIN_INPUT_PULLUP | MUX_MODE4)   /* uart3_rts_sd.gpio_164 -> cd */
+		>;
+	};
+
+	spi1_pins: pinmux_spi1_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0)   /* mcspi1_clk.mcspi1_clk */
+			OMAP3_CORE1_IOPAD(0x21ca, PIN_INPUT | MUX_MODE0)   /* mcspi1_simo.mcspi1_simo */
+			OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT | MUX_MODE0)   /* mcspi1_somi.mcspi1_somi */
+			OMAP3_CORE1_IOPAD(0x21ce, PIN_INPUT_PULLDOWN | MUX_MODE0)   /* mcspi1_cs0.mcspi1_cs0 */
+		>;
+	};
+};
+
+&gpio4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpio4_pins>;
+};
+
+&gpio5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpio5_pins>;
+};
+
+&mmc2 {
+	status = "okay";
+	bus-width = <4>;
+	vmmc-supply = <&vmmc1>;
+	cd-gpios = <&gpio6 4 0>;   /* gpio_164 */
+	wp-gpios = <&gpio6 3 0>;   /* gpio_163 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins>;
+	ti,dual-volt;
+};
+
+&mcspi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi1_pins>;
+};
+
+&gpmc {
+	ranges = <0 0 0x30000000 0x1000000>,   /* nand assigned by COM a83x */
+		<4 0 0x20000000 0x01000000>,
+		<7 0 0x15000000 0x01000000>;   /* eth assigend by COM a83x */
+
+	ethernet@4,0 {
+		compatible = "smsc,lan9117", "smsc,lan9115";
+		bank-width = <2>;
+		gpmc,mux-add-data = <2>;
+		gpmc,cs-on-ns = <10>;
+		gpmc,cs-rd-off-ns = <65>;
+		gpmc,cs-wr-off-ns = <65>;
+		gpmc,adv-on-ns = <0>;
+		gpmc,adv-rd-off-ns = <10>;
+		gpmc,adv-wr-off-ns = <10>;
+		gpmc,oe-on-ns = <10>;
+		gpmc,oe-off-ns = <65>;
+		gpmc,we-on-ns = <10>;
+		gpmc,we-off-ns = <65>;
+		gpmc,rd-cycle-ns = <100>;
+		gpmc,wr-cycle-ns = <100>;
+		gpmc,access-ns = <60>;
+		gpmc,page-burst-access-ns = <5>;
+		gpmc,bus-turnaround-ns = <0>;
+		gpmc,cycle2cycle-delay-ns = <75>;
+		gpmc,wr-data-mux-bus-ns = <15>;
+		gpmc,wr-access-ns = <75>;
+		gpmc,cycle2cycle-samecsen;
+		gpmc,cycle2cycle-diffcsen;
+		vddvario-supply = <&reg_vcc3>;
+		vdd33a-supply = <&reg_vcc3>;
+		reg-io-width = <4>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <2 0x2>;
+		reg = <4 0 0xff>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lan9117_pins>;
+		phy-mode = "mii";
+		smsc,force-internal-phy;
+	};
+};

arch/arm/boot/dts/omap3-n900.dts

@@ -74,6 +74,11 @@ proximity_sensor {
 		};
 	};
 
+	isp1704: isp1704 {
+		compatible = "nxp,isp1704";
+		nxp,enable-gpio = <&gpio3 3 GPIO_ACTIVE_HIGH>;
+		usb-phy = <&usb2_phy>;
+	};
 };
 
 &omap3_pmx_core {
@@ -254,6 +259,61 @@ twl_audio: audio {
 	};
 };
 
+&twl_keypad {
+	linux,keymap = < 0x00000010 /* KEY_Q */
+			 0x00010018 /* KEY_O */
+			 0x00020019 /* KEY_P */
+			 0x00030033 /* KEY_COMMA */
+			 0x0004000e /* KEY_BACKSPACE */
+			 0x0006001e /* KEY_A */
+			 0x0007001f /* KEY_S */
+
+			 0x01000011 /* KEY_W */
+			 0x01010020 /* KEY_D */
+			 0x01020021 /* KEY_F */
+			 0x01030022 /* KEY_G */
+			 0x01040023 /* KEY_H */
+			 0x01050024 /* KEY_J */
+			 0x01060025 /* KEY_K */
+			 0x01070026 /* KEY_L */
+
+			 0x02000012 /* KEY_E */
+			 0x02010034 /* KEY_DOT */
+			 0x02020067 /* KEY_UP */
+			 0x0203001c /* KEY_ENTER */
+			 0x0205002c /* KEY_Z */
+			 0x0206002d /* KEY_X */
+			 0x0207002e /* KEY_C */
+			 0x02080043 /* KEY_F9 */
+
+			 0x03000013 /* KEY_R */
+			 0x0301002f /* KEY_V */
+			 0x03020030 /* KEY_B */
+			 0x03030031 /* KEY_N */
+			 0x03040032 /* KEY_M */
+			 0x03050039 /* KEY_SPACE */
+			 0x03060039 /* KEY_SPACE */
+			 0x03070069 /* KEY_LEFT */
+
+			 0x04000014 /* KEY_T */
+			 0x0401006c /* KEY_DOWN */
+			 0x0402006a /* KEY_RIGHT */
+			 0x0404001d /* KEY_LEFTCTRL */
+			 0x04050064 /* KEY_RIGHTALT */
+			 0x0406002a /* KEY_LEFTSHIFT */
+			 0x04080044 /* KEY_F10 */
+
+			 0x05000015 /* KEY_Y */
+			 0x05080057 /* KEY_F11 */
+
+			 0x06000016 /* KEY_U */
+
+			 0x07000017 /* KEY_I */
+			 0x07010041 /* KEY_F7 */
+			 0x07020042 /* KEY_F8 */
+			 >;
+};
+
 &twl_gpio {
 	ti,pullups	= <0x0>;
 	ti,pulldowns	= <0x03ff3f>; /* BIT(0..5) | BIT(8..17) */
@@ -291,6 +351,13 @@ tlv320aic3x_aux: tlv320aic3x@19 {
 		DVDD-supply = <&vio>;
 	};
 
+	tsl2563: tsl2563@29 {
+		compatible = "amstaos,tsl2563";
+		reg = <0x29>;
+
+		amstaos,cover-comp-gain = <16>;
+	};
+
 	lp5523: lp5523@32 {
 		compatible = "national,lp5523";
 		reg = <0x32>;
@@ -356,6 +423,29 @@ bq27200: bq27200@55 {
 		compatible = "ti,bq27200";
 		reg = <0x55>;
 	};
+
+	tpa6130a2: tpa6130a2@60 {
+		compatible = "ti,tpa6130a2";
+		reg = <0x60>;
+
+		Vdd-supply = <&vmmc2>;
+
+		power-gpio = <&gpio4 2 GPIO_ACTIVE_HIGH>; /* 98 */
+	};
+
+	bq24150a: bq24150a@6b {
+		compatible = "ti,bq24150a";
+		reg = <0x6b>;
+
+		ti,current-limit = <100>;
+		ti,weak-battery-voltage = <3400>;
+		ti,battery-regulation-voltage = <4200>;
+		ti,charge-current = <650>;
+		ti,termination-current = <100>;
+		ti,resistor-sense = <68>;
+
+		ti,usb-charger-detection = <&isp1704>;
+	};
 };
 
 &i2c3 {

arch/arm/boot/dts/omap3-overo.dtsi

@@ -95,3 +95,7 @@ &uart3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart3_pins>;
 };
+
+&mcbsp2 {
+	status = "okay";
+};

arch/arm/boot/dts/omap3-sb-t35.dtsi

@@ -2,11 +2,36 @@
  * Common support for CompuLab SB-T35 used on SBC-T3530, SBC-T3517 and SBC-T3730
  */
 
+/ {
+	vddvario_sb_t35: regulator-vddvario-sb-t35 {
+		compatible = "regulator-fixed";
+		regulator-name = "vddvario";
+		regulator-always-on;
+	};
+
+	vdd33a_sb_t35: regulator-vdd33a-sb-t35 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd33a";
+		regulator-always-on;
+	};
+};
+
+&omap3_pmx_core {
+	smsc2_pins: pinmux_smsc2_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x20b6, PIN_OUTPUT | MUX_MODE0)	/* gpmc_ncs4.gpmc_ncs4 */
+			OMAP3_CORE1_IOPAD(0x20d2, PIN_INPUT_PULLUP | MUX_MODE4)	/* gpmc_wait3.gpio_65 */
+		>;
+	};
+};
+
 &gpmc {
 	ranges = <4 0 0x2d000000 0x01000000>;
 
 	smsc2: ethernet@4,0 {
 		compatible = "smsc,lan9221", "smsc,lan9115";
+		pinctrl-names = "default";
+		pinctrl-0 = <&smsc2_pins>;
 		interrupt-parent = <&gpio3>;
 		interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
 		reg = <4 0 0xff>;
@@ -32,8 +57,8 @@ smsc2: ethernet@4,0 {
 		gpmc,wr-access-ns = <186>;
 		gpmc,cycle2cycle-samecsen;
 		gpmc,cycle2cycle-diffcsen;
-		vddvario-supply = <&vddvario>;
-		vdd33a-supply = <&vdd33a>;
+		vddvario-supply = <&vddvario_sb_t35>;
+		vdd33a-supply = <&vdd33a_sb_t35>;
 		reg-io-width = <4>;
 		smsc,save-mac-address;
 	};

arch/arm/boot/dts/omap3-sbc-t3517.dts

+/*
+ * Suppport for CompuLab SBC-T3517 with CM-T3517
+ */
+
+#include "omap3-cm-t3517.dts"
+#include "omap3-sb-t35.dtsi"
+
+/ {
+	model = "CompuLab SBC-T3517 with CM-T3517";
+	compatible = "compulab,omap3-sbc-t3517", "compulab,omap3-cm-t3517", "ti,am3517", "ti,omap3";
+};
+
+&omap3_pmx_core {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+			&sb_t35_usb_hub_pins
+			&usb_hub_pins
+		    >;
+
+	mmc1_aux_pins: pinmux_mmc1_aux_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x20c0, PIN_INPUT_PULLUP | MUX_MODE4) /* gpmc_clk.gpio_59   */
+			OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT_PULLUP | MUX_MODE4) /* uart2_cts.gpio_144 */
+		>;
+	};
+
+	sb_t35_usb_hub_pins: pinmux_sb_t35_usb_hub_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21ec, PIN_OUTPUT | MUX_MODE4) /* ccdc_wen.gpio_98 - SB-T35 USB HUB RST */
+		>;
+	};
+};
+
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+		&mmc1_pins
+		&mmc1_aux_pins
+	>;
+
+	wp-gpios =  <&gpio2 27 GPIO_ACTIVE_HIGH>; /* gpio_59  */
+	cd-gpios =  <&gpio5 16 GPIO_ACTIVE_HIGH>; /* gpio_144 */
+};

arch/arm/boot/dts/omap3-sbc-t3530.dts

+/*
+ * Suppport for CompuLab SBC-T3530 with CM-T3530
+ */
+
+#include "omap3-cm-t3530.dts"
+#include "omap3-sb-t35.dtsi"
+
+/ {
+	model = "CompuLab SBC-T3530 with CM-T3530";
+	compatible = "compulab,omap3-sbc-t3530", "compulab,omap3-cm-t3530", "ti,omap34xx", "ti,omap3";
+};
+
+&omap3_pmx_core {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sb_t35_usb_hub_pins>;
+
+	sb_t35_usb_hub_pins: pinmux_sb_t35_usb_hub_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2130, PIN_OUTPUT | MUX_MODE4) /* ccdc_wen.gpio_167 - SB-T35 USB HUB RST */
+		>;
+	};
+};
+
+/*
+ * The following ranges correspond to SMSC9x eth chips on CM-T3530 CoM and
+ * SB-T35 baseboard respectively.
+ * This setting includes both chips in SBC-T3530 board device tree.
+ */
+&gpmc {
+	ranges = <5 0 0x2c000000 0x01000000>,
+		 <4 0 0x2d000000 0x01000000>;
+};
+
+&mmc1 {
+	cd-gpios =  <&twl_gpio 0 GPIO_ACTIVE_HIGH>;
+};

arch/arm/boot/dts/omap3-sbc-t3730.dts

@@ -10,21 +10,18 @@ / {
 	compatible = "compulab,omap3-sbc-t3730", "compulab,omap3-cm-t3730", "ti,omap36xx", "ti,omap3";
 };
 
-&gpmc {
-	ranges = <5 0 0x2c000000 0x01000000>,
-		 <4 0 0x2d000000 0x01000000>;
-};
-
-&smsc2 {
+&omap3_pmx_core {
 	pinctrl-names = "default";
-	pinctrl-0 = <&smsc2_pins>;
-};
+	pinctrl-0 = <&sb_t35_usb_hub_pins>;
 
-&omap3_pmx_core {
-	smsc2_pins: pinmux_smsc2_pins {
+	sb_t35_usb_hub_pins: pinmux_sb_t35_usb_hub_pins {
 		pinctrl-single,pins = <
-			0x86 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_ncs4.gpmc_ncs4 */
-			0xa2 (PIN_INPUT_PULLUP | MUX_MODE4)	/* gpmc_wait3.gpio_65 */
+			OMAP3_CORE1_IOPAD(0x2130, PIN_OUTPUT | MUX_MODE4) /* ccdc_wen.gpio_167 - SB-T35 USB HUB RST */
 		>;
 	};
-};
\ No newline at end of file
+};
+
+&gpmc {
+	ranges = <5 0 0x2c000000 0x01000000>,
+		 <4 0 0x2d000000 0x01000000>;
+};

arch/arm/boot/dts/omap3.dtsi

@@ -35,6 +35,11 @@ cpu@0 {
 			compatible = "arm,cortex-a8";
 			device_type = "cpu";
 			reg = <0x0>;
+
+			clocks = <&dpll1_ck>;
+			clock-names = "cpu";
+
+			clock-latency = <300000>; /* From omap-cpufreq driver */
 		};
 	};
 
@@ -436,6 +441,7 @@ mcbsp1: mcbsp@48074000 {
 			dmas = <&sdma 31>,
 			       <&sdma 32>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		mcbsp2: mcbsp@49022000 {
@@ -453,6 +459,7 @@ mcbsp2: mcbsp@49022000 {
 			dmas = <&sdma 33>,
 			       <&sdma 34>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		mcbsp3: mcbsp@49024000 {
@@ -470,6 +477,7 @@ mcbsp3: mcbsp@49024000 {
 			dmas = <&sdma 17>,
 			       <&sdma 18>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		mcbsp4: mcbsp@49026000 {
@@ -485,6 +493,7 @@ mcbsp4: mcbsp@49026000 {
 			dmas = <&sdma 19>,
 			       <&sdma 20>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		mcbsp5: mcbsp@48096000 {
@@ -500,6 +509,7 @@ mcbsp5: mcbsp@48096000 {
 			dmas = <&sdma 21>,
 			       <&sdma 22>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		sham: sham@480c3000 {

arch/arm/boot/dts/omap3430-sdp.dts

@@ -34,6 +34,10 @@ twl: twl@48 {
 &mmc1 {
 	vmmc-supply = <&vmmc1>;
 	vmmc_aux-supply = <&vsim>;
+	/*
+	 * S6-3 must be in ON position for 8 bit mode to function
+	 * Else, use 4 bit mode
+	 */
 	bus-width = <8>;
 };
 
@@ -103,9 +107,8 @@ nand@1,0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		reg = <1 0 0x08000000>;
+		ti,nand-ecc-opt = "ham1";
 		nand-bus-width = <8>;
-
-		ti,nand-ecc-opt = "sw";
 		gpmc,cs-on-ns = <0>;
 		gpmc,cs-rd-off-ns = <36>;
 		gpmc,cs-wr-off-ns = <36>;

arch/arm/boot/dts/omap3430es1-clocks.dtsi

@@ -82,16 +82,16 @@ ssi_ssr_div_fck_3430es1: ssi_ssr_div_fck_3430es1 {
 		ti,dividers = <0>, <1>, <2>, <3>, <4>, <0>, <6>, <0>, <8>;
 	};
 
-	ssi_ssr_fck_3430es1: ssi_ssr_fck_3430es1 {
+	ssi_ssr_fck: ssi_ssr_fck_3430es1 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
 		clocks = <&ssi_ssr_gate_fck_3430es1>, <&ssi_ssr_div_fck_3430es1>;
 	};
 
-	ssi_sst_fck_3430es1: ssi_sst_fck_3430es1 {
+	ssi_sst_fck: ssi_sst_fck_3430es1 {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
-		clocks = <&ssi_ssr_fck_3430es1>;
+		clocks = <&ssi_ssr_fck>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
@@ -120,7 +120,7 @@ ssi_l4_ick: ssi_l4_ick {
 		clock-div = <1>;
 	};
 
-	ssi_ick_3430es1: ssi_ick_3430es1 {
+	ssi_ick: ssi_ick_3430es1 {
 		#clock-cells = <0>;
 		compatible = "ti,omap3-no-wait-interface-clock";
 		clocks = <&ssi_l4_ick>;
@@ -203,6 +203,6 @@ core_l4_clkdm: core_l4_clkdm {
 			 <&i2c1_ick>, <&uart2_ick>, <&uart1_ick>, <&gpt11_ick>,
 			 <&gpt10_ick>, <&mcbsp5_ick>, <&mcbsp1_ick>,
 			 <&omapctrl_ick>, <&aes2_ick>, <&sha12_ick>,
-			 <&fshostusb_fck>, <&fac_ick>, <&ssi_ick_3430es1>;
+			 <&fshostusb_fck>, <&fac_ick>, <&ssi_ick>;
 	};
 };

arch/arm/boot/dts/omap36xx-omap3430es2plus-clocks.dtsi

@@ -25,16 +25,16 @@ ssi_ssr_div_fck_3430es2: ssi_ssr_div_fck_3430es2 {
 		ti,dividers = <0>, <1>, <2>, <3>, <4>, <0>, <6>, <0>, <8>;
 	};
 
-	ssi_ssr_fck_3430es2: ssi_ssr_fck_3430es2 {
+	ssi_ssr_fck: ssi_ssr_fck_3430es2 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
 		clocks = <&ssi_ssr_gate_fck_3430es2>, <&ssi_ssr_div_fck_3430es2>;
 	};
 
-	ssi_sst_fck_3430es2: ssi_sst_fck_3430es2 {
+	ssi_sst_fck: ssi_sst_fck_3430es2 {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
-		clocks = <&ssi_ssr_fck_3430es2>;
+		clocks = <&ssi_ssr_fck>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
@@ -55,7 +55,7 @@ ssi_l4_ick: ssi_l4_ick {
 		clock-div = <1>;
 	};
 
-	ssi_ick_3430es2: ssi_ick_3430es2 {
+	ssi_ick: ssi_ick_3430es2 {
 		#clock-cells = <0>;
 		compatible = "ti,omap3-ssi-interface-clock";
 		clocks = <&ssi_l4_ick>;
@@ -193,6 +193,6 @@ core_l4_clkdm: core_l4_clkdm {
 			 <&i2c1_ick>, <&uart2_ick>, <&uart1_ick>, <&gpt11_ick>,
 			 <&gpt10_ick>, <&mcbsp5_ick>, <&mcbsp1_ick>,
 			 <&omapctrl_ick>, <&aes2_ick>, <&sha12_ick>,
-			 <&ssi_ick_3430es2>;
+			 <&ssi_ick>;
 	};
 };

arch/arm/boot/dts/omap4-panda-common.dtsi

@@ -109,9 +109,6 @@ wl12xx_vmmc: wl12xx_vmmc {
 &omap4_pmx_core {
 	pinctrl-names = "default";
 	pinctrl-0 = <
-			&twl6040_pins
-			&mcpdm_pins
-			&mcbsp1_pins
 			&dss_dpi_pins
 			&tfp410_pins
 			&dss_hdmi_pins
@@ -300,6 +297,10 @@ twl: twl@48 {
 	twl6040: twl@4b {
 		compatible = "ti,twl6040";
 		reg = <0x4b>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&twl6040_pins>;
+
 		/* IRQ# = 119 */
 		interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_2N cascaded to gic */
 		interrupt-parent = <&gic>;
@@ -380,16 +381,16 @@ &emif2 {
 	device-handle = <&elpida_ECB240ABACN>;
 };
 
-&mcbsp2 {
-	status = "disabled";
-};
-
-&mcbsp3 {
-	status = "disabled";
+&mcbsp1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcbsp1_pins>;
+	status = "okay";
 };
 
-&dmic {
-	status = "disabled";
+&mcpdm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcpdm_pins>;
+	status = "okay";
 };
 
 &twl_usb_comparator {

arch/arm/boot/dts/omap4-sdp.dts

@@ -158,11 +158,6 @@ wl12xx_vmmc: wl12xx_vmmc {
 &omap4_pmx_core {
 	pinctrl-names = "default";
 	pinctrl-0 = <
-			&twl6040_pins
-			&mcpdm_pins
-			&dmic_pins
-			&mcbsp1_pins
-			&mcbsp2_pins
 			&dss_hdmi_pins
 			&tpd12s015_pins
 	>;
@@ -326,6 +321,10 @@ twl: twl@48 {
 	twl6040: twl@4b {
 		compatible = "ti,twl6040";
 		reg = <0x4b>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&twl6040_pins>;
+
 		/* SPI = 0, IRQ# = 119, 4 = active high level-sensitive */
 		interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_2N cascaded to gic */
 		interrupt-parent = <&gic>;
@@ -537,8 +536,28 @@ &uart4 {
 	pinctrl-0 = <&uart4_pins>;
 };
 
-&mcbsp3 {
-	status = "disabled";
+&mcbsp1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcbsp1_pins>;
+	status = "okay";
+};
+
+&mcbsp2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcbsp2_pins>;
+	status = "okay";
+};
+
+&dmic {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dmic_pins>;
+	status = "okay";
+};
+
+&mcpdm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcpdm_pins>;
+	status = "okay";
 };
 
 &twl_usb_comparator {

arch/arm/boot/dts/omap4.dtsi

@@ -36,6 +36,11 @@ cpu@0 {
 			device_type = "cpu";
 			next-level-cache = <&L2>;
 			reg = <0x0>;
+
+			clocks = <&dpll_mpu_ck>;
+			clock-names = "cpu";
+
+			clock-latency = <300000>; /* From omap-cpufreq driver */
 		};
 		cpu@1 {
 			compatible = "arm,cortex-a9";
@@ -313,6 +318,7 @@ hwspinlock: spinlock@4a0f6000 {
 			compatible = "ti,omap4-hwspinlock";
 			reg = <0x4a0f6000 0x1000>;
 			ti,hwmods = "spinlock";
+			#hwlock-cells = <1>;
 		};
 
 		i2c1: i2c@48070000 {
@@ -478,6 +484,7 @@ mcpdm: mcpdm@40132000 {
 			dmas = <&sdma 65>,
 			       <&sdma 66>;
 			dma-names = "up_link", "dn_link";
+			status = "disabled";
 		};
 
 		dmic: dmic@4012e000 {
@@ -489,6 +496,7 @@ dmic: dmic@4012e000 {
 			ti,hwmods = "dmic";
 			dmas = <&sdma 67>;
 			dma-names = "up_link";
+			status = "disabled";
 		};
 
 		mcbsp1: mcbsp@40122000 {
@@ -503,6 +511,7 @@ mcbsp1: mcbsp@40122000 {
 			dmas = <&sdma 33>,
 			       <&sdma 34>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		mcbsp2: mcbsp@40124000 {
@@ -517,6 +526,7 @@ mcbsp2: mcbsp@40124000 {
 			dmas = <&sdma 17>,
 			       <&sdma 18>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		mcbsp3: mcbsp@40126000 {
@@ -531,6 +541,7 @@ mcbsp3: mcbsp@40126000 {
 			dmas = <&sdma 19>,
 			       <&sdma 20>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		mcbsp4: mcbsp@48096000 {
@@ -544,6 +555,7 @@ mcbsp4: mcbsp@48096000 {
 			dmas = <&sdma 31>,
 			       <&sdma 32>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		keypad: keypad@4a31c000 {
@@ -554,6 +566,13 @@ keypad: keypad@4a31c000 {
 			ti,hwmods = "kbd";
 		};
 
+		dmm@4e000000 {
+			compatible = "ti,omap4-dmm";
+			reg = <0x4e000000 0x800>;
+			interrupts = <0 113 0x4>;
+			ti,hwmods = "dmm";
+		};
+
 		emif1: emif@4c000000 {
 			compatible = "ti,emif-4d";
 			reg = <0x4c000000 0x100>;

arch/arm/boot/dts/omap5.dtsi

@@ -49,6 +49,12 @@ cpu0: cpu@0 {
 				1000000 1060000
 				1500000 1250000
 			>;
+
+			clocks = <&dpll_mpu_ck>;
+			clock-names = "cpu";
+
+			clock-latency = <300000>; /* From omap-cpufreq driver */
+
 			/* cooling options */
 			cooling-min-level = <0>;
 			cooling-max-level = <2>;
@@ -353,6 +359,7 @@ hwspinlock: spinlock@4a0f6000 {
 			compatible = "ti,omap4-hwspinlock";
 			reg = <0x4a0f6000 0x1000>;
 			ti,hwmods = "spinlock";
+			#hwlock-cells = <1>;
 		};
 
 		mcspi1: spi@48098000 {
@@ -529,6 +536,7 @@ mcpdm: mcpdm@40132000 {
 			dmas = <&sdma 65>,
 			       <&sdma 66>;
 			dma-names = "up_link", "dn_link";
+			status = "disabled";
 		};
 
 		dmic: dmic@4012e000 {
@@ -540,6 +548,7 @@ dmic: dmic@4012e000 {
 			ti,hwmods = "dmic";
 			dmas = <&sdma 67>;
 			dma-names = "up_link";
+			status = "disabled";
 		};
 
 		mcbsp1: mcbsp@40122000 {
@@ -554,6 +563,7 @@ mcbsp1: mcbsp@40122000 {
 			dmas = <&sdma 33>,
 			       <&sdma 34>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		mcbsp2: mcbsp@40124000 {
@@ -568,6 +578,7 @@ mcbsp2: mcbsp@40124000 {
 			dmas = <&sdma 17>,
 			       <&sdma 18>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		mcbsp3: mcbsp@40126000 {
@@ -582,6 +593,7 @@ mcbsp3: mcbsp@40126000 {
 			dmas = <&sdma 19>,
 			       <&sdma 20>;
 			dma-names = "tx", "rx";
+			status = "disabled";
 		};
 
 		timer1: timer@4ae18000 {
@@ -683,6 +695,13 @@ wdt2: wdt@4ae14000 {
 			ti,hwmods = "wd_timer2";
 		};
 
+		dmm@4e000000 {
+			compatible = "ti,omap5-dmm";
+			reg = <0x4e000000 0x800>;
+			interrupts = <0 113 0x4>;
+			ti,hwmods = "dmm";
+		};
+
 		emif1: emif@4c000000 {
 			compatible	= "ti,emif-4d5";
 			ti,hwmods	= "emif1";

arch/arm/boot/dts/tps65910.dtsi

@@ -82,5 +82,10 @@ vmmc_reg: regulator@12 {
 			reg = <12>;
 			regulator-compatible = "vmmc";
 		};
+
+		vbb_reg: regulator@13 {
+			reg = <13>;
+			regulator-compatible = "vbb";
+		};
 	};
 };

arch/arm/boot/dts/twl4030.dtsi

@@ -145,4 +145,11 @@ twl_pwrbutton: pwrbutton {
 		compatible = "ti,twl4030-pwrbutton";
 		interrupts = <8>;
 	};
+
+	twl_keypad: keypad {
+		compatible = "ti,twl4030-keypad";
+		interrupts = <1>;
+		keypad,num-rows = <8>;
+		keypad,num-columns = <8>;
+	};
 };

arch/arm/mach-omap2/gpmc-nand.c

@@ -45,24 +45,31 @@ static struct platform_device gpmc_nand_device = {
 
 static bool gpmc_hwecc_bch_capable(enum omap_ecc ecc_opt)
 {
-	/* support only OMAP3 class */
-	if (!cpu_is_omap34xx() && !soc_is_am33xx()) {
-		pr_err("BCH ecc is not supported on this CPU\n");
+	/* platforms which support all ECC schemes */
+	if (soc_is_am33xx() || cpu_is_omap44xx() ||
+		 soc_is_omap54xx() || soc_is_dra7xx())
+		return 1;
+
+	/* OMAP3xxx do not have ELM engine, so cannot support ECC schemes
+	 * which require H/W based ECC error detection */
+	if ((cpu_is_omap34xx() || cpu_is_omap3630()) &&
+	    ((ecc_opt == OMAP_ECC_BCH4_CODE_HW) ||
+		 (ecc_opt == OMAP_ECC_BCH8_CODE_HW)))
 		return 0;
-	}
 
 	/*
 	 * For now, assume 4-bit mode is only supported on OMAP3630 ES1.x, x>=1
 	 * and AM33xx derivates. Other chips may be added if confirmed to work.
 	 */
-	if ((ecc_opt == OMAP_ECC_BCH4_CODE_HW) &&
-	    (!cpu_is_omap3630() || (GET_OMAP_REVISION() == 0)) &&
-	    (!soc_is_am33xx())) {
-		pr_err("BCH 4-bit mode is not supported on this CPU\n");
+	if ((ecc_opt == OMAP_ECC_BCH4_CODE_HW_DETECTION_SW) &&
+	    (!cpu_is_omap3630() || (GET_OMAP_REVISION() == 0)))
 		return 0;
-	}
 
-	return 1;
+	/* legacy platforms support only HAM1 (1-bit Hamming) ECC scheme */
+	if (ecc_opt == OMAP_ECC_HAM1_CODE_HW)
+		return 1;
+	else
+		return 0;
 }
 
 /* This function will go away once the device-tree convertion is complete */
@@ -133,8 +140,10 @@ int gpmc_nand_init(struct omap_nand_platform_data *gpmc_nand_data,
 
 	gpmc_update_nand_reg(&gpmc_nand_data->reg, gpmc_nand_data->cs);
 
-	if (!gpmc_hwecc_bch_capable(gpmc_nand_data->ecc_opt))
+	if (!gpmc_hwecc_bch_capable(gpmc_nand_data->ecc_opt)) {
+		dev_err(dev, "Unsupported NAND ECC scheme selected\n");
 		return -EINVAL;
+	}
 
 	err = platform_device_register(&gpmc_nand_device);
 	if (err < 0) {

arch/arm/mach-omap2/pdata-quirks.c

@@ -99,7 +99,7 @@ static int omap3_sbc_t3730_twl_callback(struct device *dev,
 	int res;
 
 	res = gpio_request_one(gpio + 2, GPIOF_OUT_INIT_HIGH,
-			       "wlan rst");
+			       "wlan pwr");
 	if (res)
 		return res;
 
@@ -108,6 +108,23 @@ static int omap3_sbc_t3730_twl_callback(struct device *dev,
 	return 0;
 }
 
+static void __init omap3_sbc_t3x_usb_hub_init(int gpio, char *hub_name)
+{
+	int err = gpio_request_one(gpio, GPIOF_OUT_INIT_LOW, hub_name);
+
+	if (err) {
+		pr_err("SBC-T3x: %s reset gpio request failed: %d\n",
+			hub_name, err);
+		return;
+	}
+
+	gpio_export(gpio, 0);
+
+	udelay(10);
+	gpio_set_value(gpio, 1);
+	msleep(1);
+}
+
 static void __init omap3_sbc_t3730_twl_init(void)
 {
 	twl_gpio_auxdata.setup = omap3_sbc_t3730_twl_callback;
@@ -115,10 +132,17 @@ static void __init omap3_sbc_t3730_twl_init(void)
 
 static void __init omap3_sbc_t3730_legacy_init(void)
 {
+	omap3_sbc_t3x_usb_hub_init(167, "sb-t35 usb hub");
 	legacy_init_wl12xx(WL12XX_REFCLOCK_38, 0, 136);
 	omap_ads7846_init(1, 57, 0, NULL);
 }
 
+static void __init omap3_sbc_t3530_legacy_init(void)
+{
+	omap3_sbc_t3x_usb_hub_init(167, "sb-t35 usb hub");
+	omap_ads7846_init(1, 57, 0, NULL);
+}
+
 static void __init omap3_igep0020_legacy_init(void)
 {
 	omap3_igep2_display_init_of();
@@ -160,7 +184,7 @@ static struct emac_platform_data am35xx_emac_pdata = {
 	.interrupt_disable	= am35xx_disable_emac_int,
 };
 
-static void __init am3517_evm_legacy_init(void)
+static void __init am35xx_emac_reset(void)
 {
 	u32 v;
 
@@ -169,6 +193,43 @@ static void __init am3517_evm_legacy_init(void)
 	omap_ctrl_writel(v, AM35XX_CONTROL_IP_SW_RESET);
 	omap_ctrl_readl(AM35XX_CONTROL_IP_SW_RESET); /* OCP barrier */
 }
+
+static struct gpio cm_t3517_wlan_gpios[] __initdata = {
+	{ 56,	GPIOF_OUT_INIT_HIGH,	"wlan pwr" },
+	{ 4,	GPIOF_OUT_INIT_HIGH,	"xcvr noe" },
+};
+
+static void __init omap3_sbc_t3517_wifi_init(void)
+{
+	int err = gpio_request_array(cm_t3517_wlan_gpios,
+				ARRAY_SIZE(cm_t3517_wlan_gpios));
+	if (err) {
+		pr_err("SBC-T3517: wl12xx gpios request failed: %d\n", err);
+		return;
+	}
+
+	gpio_export(cm_t3517_wlan_gpios[0].gpio, 0);
+	gpio_export(cm_t3517_wlan_gpios[1].gpio, 0);
+
+	msleep(100);
+	gpio_set_value(cm_t3517_wlan_gpios[1].gpio, 0);
+}
+
+static void __init omap3_sbc_t3517_legacy_init(void)
+{
+	omap3_sbc_t3x_usb_hub_init(152, "cm-t3517 usb hub");
+	omap3_sbc_t3x_usb_hub_init(98, "sb-t35 usb hub");
+	am35xx_emac_reset();
+	hsmmc2_internal_input_clk();
+	omap3_sbc_t3517_wifi_init();
+	legacy_init_wl12xx(WL12XX_REFCLOCK_38, 0, 145);
+	omap_ads7846_init(1, 57, 0, NULL);
+}
+
+static void __init am3517_evm_legacy_init(void)
+{
+	am35xx_emac_reset();
+}
 #endif /* CONFIG_ARCH_OMAP3 */
 
 #ifdef CONFIG_ARCH_OMAP4
@@ -258,6 +319,8 @@ struct of_dev_auxdata omap_auxdata_lookup[] __initdata = {
  */
 static struct pdata_init pdata_quirks[] __initdata = {
 #ifdef CONFIG_ARCH_OMAP3
+	{ "compulab,omap3-sbc-t3517", omap3_sbc_t3517_legacy_init, },
+	{ "compulab,omap3-sbc-t3530", omap3_sbc_t3530_legacy_init, },
 	{ "compulab,omap3-sbc-t3730", omap3_sbc_t3730_legacy_init, },
 	{ "nokia,omap3-n900", hsmmc2_internal_input_clk, },
 	{ "nokia,omap3-n9", hsmmc2_internal_input_clk, },

include/dt-bindings/pinctrl/am43xx.h

@@ -13,6 +13,7 @@
 #define MUX_MODE5	5
 #define MUX_MODE6	6
 #define MUX_MODE7	7
+#define MUX_MODE8	8
 
 #define PULL_DISABLE		(1 << 16)
 #define PULL_UP			(1 << 17)