Commit 221c5637 authored by Matt Carlson's avatar Matt Carlson Committed by David S. Miller

tg3: Migrate phy preprocessor defs to system defs

This patch changes to code to use some of the preprocessor
definitions from mii.h over its homegrown equivalents.
Signed-off-by: default avatarMatt Carlson <mcarlson@broadcom.com>
Reviewed-by: default avatarMichael Chan <mchan@broadcom.com>
Reviewed-by: default avatarBenjamin Li <benli@broadcom.com>
Signed-off-by: default avatarDavid S. Miller <davem@conan.davemloft.net>
parent 5bb09778
......@@ -861,7 +861,7 @@ static int tg3_writephy(struct tg3 *tp, int reg, u32 val)
int ret;
if ((tp->phy_flags & TG3_PHYFLG_IS_FET) &&
(reg == MII_TG3_CTRL || reg == MII_TG3_AUX_CTRL))
(reg == MII_CTRL1000 || reg == MII_TG3_AUX_CTRL))
return 0;
if ((tp->mi_mode & MAC_MI_MODE_AUTO_POLL) != 0) {
......@@ -1981,15 +1981,14 @@ static int tg3_phy_reset_5703_4_5(struct tg3 *tp)
/* Set full-duplex, 1000 mbps. */
tg3_writephy(tp, MII_BMCR,
BMCR_FULLDPLX | TG3_BMCR_SPEED1000);
BMCR_FULLDPLX | BMCR_SPEED1000);
/* Set to master mode. */
if (tg3_readphy(tp, MII_TG3_CTRL, &phy9_orig))
if (tg3_readphy(tp, MII_CTRL1000, &phy9_orig))
continue;
tg3_writephy(tp, MII_TG3_CTRL,
(MII_TG3_CTRL_AS_MASTER |
MII_TG3_CTRL_ENABLE_AS_MASTER));
tg3_writephy(tp, MII_CTRL1000,
CTL1000_AS_MASTER | CTL1000_ENABLE_MASTER);
err = TG3_PHY_AUXCTL_SMDSP_ENABLE(tp);
if (err)
......@@ -2014,7 +2013,7 @@ static int tg3_phy_reset_5703_4_5(struct tg3 *tp)
TG3_PHY_AUXCTL_SMDSP_DISABLE(tp);
tg3_writephy(tp, MII_TG3_CTRL, phy9_orig);
tg3_writephy(tp, MII_CTRL1000, phy9_orig);
if (!tg3_readphy(tp, MII_TG3_EXT_CTRL, &reg32)) {
reg32 &= ~0x3000;
......@@ -2958,16 +2957,15 @@ static int tg3_phy_autoneg_cfg(struct tg3 *tp, u32 advertise, u32 flowctrl)
new_adv = 0;
if (advertise & ADVERTISED_1000baseT_Half)
new_adv |= MII_TG3_CTRL_ADV_1000_HALF;
new_adv |= ADVERTISE_1000HALF;
if (advertise & ADVERTISED_1000baseT_Full)
new_adv |= MII_TG3_CTRL_ADV_1000_FULL;
new_adv |= ADVERTISE_1000FULL;
if (tp->pci_chip_rev_id == CHIPREV_ID_5701_A0 ||
tp->pci_chip_rev_id == CHIPREV_ID_5701_B0)
new_adv |= (MII_TG3_CTRL_AS_MASTER |
MII_TG3_CTRL_ENABLE_AS_MASTER);
new_adv |= CTL1000_AS_MASTER | CTL1000_ENABLE_MASTER;
err = tg3_writephy(tp, MII_TG3_CTRL, new_adv);
err = tg3_writephy(tp, MII_CTRL1000, new_adv);
if (err)
goto done;
......@@ -3076,7 +3074,7 @@ static void tg3_phy_copper_begin(struct tg3 *tp)
break;
case SPEED_1000:
bmcr |= TG3_BMCR_SPEED1000;
bmcr |= BMCR_SPEED1000;
break;
}
......@@ -3153,7 +3151,7 @@ static int tg3_copper_is_advertising_all(struct tg3 *tp, u32 mask)
if (mask & ADVERTISED_1000baseT_Full)
all_mask |= ADVERTISE_1000FULL;
if (tg3_readphy(tp, MII_TG3_CTRL, &tg3_ctrl))
if (tg3_readphy(tp, MII_CTRL1000, &tg3_ctrl))
return 0;
if ((tg3_ctrl & all_mask) != all_mask)
......
......@@ -2152,14 +2152,6 @@
/*** Tigon3 specific PHY MII registers. ***/
#define TG3_BMCR_SPEED1000 0x0040
#define MII_TG3_CTRL 0x09 /* 1000-baseT control register */
#define MII_TG3_CTRL_ADV_1000_HALF 0x0100
#define MII_TG3_CTRL_ADV_1000_FULL 0x0200
#define MII_TG3_CTRL_AS_MASTER 0x0800
#define MII_TG3_CTRL_ENABLE_AS_MASTER 0x1000
#define MII_TG3_MMD_CTRL 0x0d /* MMD Access Control register */
#define MII_TG3_MMD_CTRL_DATA_NOINC 0x4000
#define MII_TG3_MMD_ADDRESS 0x0e /* MMD Address Data register */
......
......@@ -128,6 +128,8 @@
/* 1000BASE-T Control register */
#define ADVERTISE_1000FULL 0x0200 /* Advertise 1000BASE-T full duplex */
#define ADVERTISE_1000HALF 0x0100 /* Advertise 1000BASE-T half duplex */
#define CTL1000_AS_MASTER 0x0800
#define CTL1000_ENABLE_MASTER 0x1000
/* 1000BASE-T Status register */
#define LPA_1000LOCALRXOK 0x2000 /* Link partner local receiver status */
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment