Commit 229d495d authored by Josh Lehan's avatar Josh Lehan Committed by Guenter Roeck

hwmon: (lm90) Add max6654 support to lm90 driver

Add support for the Maxim MAX6654 to the lm90 driver.

The MAX6654 is a temperature sensor, similar to the others,
but with some differences regarding the configuration
register, and the sampling rate at which extended resolution
becomes possible.
Signed-off-by: default avatarJosh Lehan <krellan@google.com>
Link: https://lore.kernel.org/r/20200513184248.145765-1-krellan@google.comSigned-off-by: default avatarGuenter Roeck <linux@roeck-us.net>
parent 036855a4
......@@ -123,6 +123,18 @@ Supported chips:
http://www.maxim-ic.com/quick_view2.cfm/qv_pk/3497
* Maxim MAX6654
Prefix: 'max6654'
Addresses scanned: I2C 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b,
0x4c, 0x4d and 0x4e
Datasheet: Publicly available at the Maxim website
https://www.maximintegrated.com/en/products/sensors/MAX6654.html
* Maxim MAX6657
Prefix: 'max6657'
......@@ -301,6 +313,13 @@ ADT7461, ADT7461A, NCT1008:
* Extended temperature range (breaks compatibility)
* Lower resolution for remote temperature
MAX6654:
* Better local resolution
* Selectable address
* Remote sensor type selection
* Extended temperature range
* Extended resolution only available when conversion rate <= 1 Hz
MAX6657 and MAX6658:
* Better local resolution
* Remote sensor type selection
......@@ -336,8 +355,8 @@ SA56004X:
All temperature values are given in degrees Celsius. Resolution
is 1.0 degree for the local temperature, 0.125 degree for the remote
temperature, except for the MAX6657, MAX6658 and MAX6659 which have a
resolution of 0.125 degree for both temperatures.
temperature, except for the MAX6654, MAX6657, MAX6658 and MAX6659 which have
a resolution of 0.125 degree for both temperatures.
Each sensor has its own high and low limits, plus a critical limit.
Additionally, there is a relative hysteresis value common to both critical
......
......@@ -1198,10 +1198,11 @@ config SENSORS_LM90
help
If you say yes here you get support for National Semiconductor LM90,
LM86, LM89 and LM99, Analog Devices ADM1032, ADT7461, and ADT7461A,
Maxim MAX6646, MAX6647, MAX6648, MAX6649, MAX6657, MAX6658, MAX6659,
MAX6680, MAX6681, MAX6692, MAX6695, MAX6696, ON Semiconductor NCT1008,
Winbond/Nuvoton W83L771W/G/AWG/ASG, Philips SA56004, GMT G781, and
Texas Instruments TMP451 sensor chips.
Maxim MAX6646, MAX6647, MAX6648, MAX6649, MAX6654, MAX6657, MAX6658,
MAX6659, MAX6680, MAX6681, MAX6692, MAX6695, MAX6696,
ON Semiconductor NCT1008, Winbond/Nuvoton W83L771W/G/AWG/ASG,
Philips SA56004, GMT G781, and Texas Instruments TMP451
sensor chips.
This driver can also be built as a module. If so, the module
will be called lm90.
......
......@@ -35,6 +35,14 @@
* explicitly as max6659, or if its address is not 0x4c.
* These chips lack the remote temperature offset feature.
*
* This driver also supports the MAX6654 chip made by Maxim. This chip can
* be at 9 different addresses, similar to MAX6680/MAX6681. The MAX6654 is
* otherwise similar to MAX6657/MAX6658/MAX6659. Extended range is available
* by setting the configuration register accordingly, and is done during
* initialization. Extended precision is only available at conversion rates
* of 1 Hz and slower. Note that extended precision is not enabled by
* default, as this driver initializes all chips to 2 Hz by design.
*
* This driver also supports the MAX6646, MAX6647, MAX6648, MAX6649 and
* MAX6692 chips made by Maxim. These are again similar to the LM86,
* but they use unsigned temperature values and can report temperatures
......@@ -94,8 +102,8 @@
* have address 0x4d.
* MAX6647 has address 0x4e.
* MAX6659 can have address 0x4c, 0x4d or 0x4e.
* MAX6680 and MAX6681 can have address 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b,
* 0x4c, 0x4d or 0x4e.
* MAX6654, MAX6680, and MAX6681 can have address 0x18, 0x19, 0x1a, 0x29,
* 0x2a, 0x2b, 0x4c, 0x4d or 0x4e.
* SA56004 can have address 0x48 through 0x4F.
*/
......@@ -104,7 +112,7 @@ static const unsigned short normal_i2c[] = {
0x4d, 0x4e, 0x4f, I2C_CLIENT_END };
enum chips { lm90, adm1032, lm99, lm86, max6657, max6659, adt7461, max6680,
max6646, w83l771, max6696, sa56004, g781, tmp451 };
max6646, w83l771, max6696, sa56004, g781, tmp451, max6654 };
/*
* The LM90 registers
......@@ -145,7 +153,7 @@ enum chips { lm90, adm1032, lm99, lm86, max6657, max6659, adt7461, max6680,
#define LM90_REG_R_TCRIT_HYST 0x21
#define LM90_REG_W_TCRIT_HYST 0x21
/* MAX6646/6647/6649/6657/6658/6659/6695/6696 registers */
/* MAX6646/6647/6649/6654/6657/6658/6659/6695/6696 registers */
#define MAX6657_REG_R_LOCAL_TEMPL 0x11
#define MAX6696_REG_R_STATUS2 0x12
......@@ -209,6 +217,7 @@ static const struct i2c_device_id lm90_id[] = {
{ "max6646", max6646 },
{ "max6647", max6646 },
{ "max6649", max6646 },
{ "max6654", max6654 },
{ "max6657", max6657 },
{ "max6658", max6657 },
{ "max6659", max6659 },
......@@ -269,6 +278,10 @@ static const struct of_device_id __maybe_unused lm90_of_match[] = {
.compatible = "dallas,max6649",
.data = (void *)max6646
},
{
.compatible = "dallas,max6654",
.data = (void *)max6654
},
{
.compatible = "dallas,max6657",
.data = (void *)max6657
......@@ -367,6 +380,11 @@ static const struct lm90_params lm90_params[] = {
.max_convrate = 6,
.reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL,
},
[max6654] = {
.alert_alarms = 0x7c,
.max_convrate = 7,
.reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL,
},
[max6657] = {
.flags = LM90_PAUSE_FOR_CONFIG,
.alert_alarms = 0x7c,
......@@ -1557,6 +1575,16 @@ static int lm90_detect(struct i2c_client *client,
&& (config1 & 0x3f) == 0x00
&& convrate <= 0x07) {
name = "max6646";
} else
/*
* The chip_id of the MAX6654 holds the revision of the chip.
* The lowest 3 bits of the config1 register are unused and
* should return zero when read.
*/
if (chip_id == 0x08
&& (config1 & 0x07) == 0x00
&& convrate <= 0x07) {
name = "max6654";
}
} else
if (address == 0x4C
......@@ -1660,6 +1688,15 @@ static int lm90_init_client(struct i2c_client *client, struct lm90_data *data)
if (data->kind == max6680)
config |= 0x18;
/*
* Put MAX6654 into extended range (0x20, extend minimum range from
* 0 degrees to -64 degrees). Note that extended resolution is not
* possible on the MAX6654 unless conversion rate is set to 1 Hz or
* slower, which is intentionally not done by default.
*/
if (data->kind == max6654)
config |= 0x20;
/*
* Select external channel 0 for max6695/96
*/
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment