xhci: define the new default speed ID for SuperSpeedPlus used by xhci hw

USB 3.1 capable xhci controllers use a new default speed ID "5" in the
PORTSC register to represent a 10Gbps connection speed of a SuperSpeedPlus
device

Make sure the xhci driver can handle the returned SuperSpeedPlus speed ID
properly
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/usb/host/xhci-hub.c

@@ -713,7 +713,7 @@ static u32 xhci_get_port_status(struct usb_hcd *hcd,
 			status |= USB_PORT_STAT_SUSPEND;
 	}
 	if ((raw_port_status & PORT_PLS_MASK) == XDEV_RESUME &&
-			!DEV_SUPERSPEED(raw_port_status)) {
+		!DEV_SUPERSPEED_ANY(raw_port_status)) {
 		if ((raw_port_status & PORT_RESET) ||
 				!(raw_port_status & PORT_PE))
 			return 0xffffffff;
@@ -1311,14 +1311,14 @@ int xhci_bus_resume(struct usb_hcd *hcd)
 		u32 temp;
 
 		temp = readl(port_array[port_index]);
-		if (DEV_SUPERSPEED(temp))
+		if (DEV_SUPERSPEED_ANY(temp))
 			temp &= ~(PORT_RWC_BITS | PORT_CEC | PORT_WAKE_BITS);
 		else
 			temp &= ~(PORT_RWC_BITS | PORT_WAKE_BITS);
 		if (test_bit(port_index, &bus_state->bus_suspended) &&
 		    (temp & PORT_PLS_MASK)) {
 			set_bit(port_index, &port_was_suspended);
-			if (!DEV_SUPERSPEED(temp)) {
+			if (!DEV_SUPERSPEED_ANY(temp)) {
 				xhci_set_link_state(xhci, port_array,
 						port_index, XDEV_RESUME);
 				need_usb2_u3_exit = true;

drivers/usb/host/xhci-ring.c

@@ -1567,7 +1567,7 @@ static void handle_port_status(struct xhci_hcd *xhci,
 			goto cleanup;
 		}
 
-		if (DEV_SUPERSPEED(temp)) {
+		if (DEV_SUPERSPEED_ANY(temp)) {
 			xhci_dbg(xhci, "remote wake SS port %d\n", port_id);
 			/* Set a flag to say the port signaled remote wakeup,
 			 * so we can tell the difference between the end of
@@ -1595,7 +1595,7 @@ static void handle_port_status(struct xhci_hcd *xhci,
 	}
 
 	if ((temp & PORT_PLC) && (temp & PORT_PLS_MASK) == XDEV_U0 &&
-			DEV_SUPERSPEED(temp)) {
+			DEV_SUPERSPEED_ANY(temp)) {
 		xhci_dbg(xhci, "resume SS port %d finished\n", port_id);
 		/* We've just brought the device into U0 through either the
 		 * Resume state after a device remote wakeup, or through the
@@ -1625,7 +1625,7 @@ static void handle_port_status(struct xhci_hcd *xhci,
 	 * RExit to a disconnect state).  If so, let the the driver know it's
 	 * out of the RExit state.
 	 */
-	if (!DEV_SUPERSPEED(temp) &&
+	if (!DEV_SUPERSPEED_ANY(temp) &&
 			test_and_clear_bit(faked_port_index,
 				&bus_state->rexit_ports)) {
 		complete(&bus_state->rexit_done[faked_port_index]);

drivers/usb/host/xhci.h

@@ -327,11 +327,15 @@ struct xhci_op_regs {
 #define	XDEV_LS			(0x2 << 10)
 #define	XDEV_HS			(0x3 << 10)
 #define	XDEV_SS			(0x4 << 10)
+#define	XDEV_SSP		(0x5 << 10)
 #define DEV_UNDEFSPEED(p)	(((p) & DEV_SPEED_MASK) == (0x0<<10))
 #define DEV_FULLSPEED(p)	(((p) & DEV_SPEED_MASK) == XDEV_FS)
 #define DEV_LOWSPEED(p)		(((p) & DEV_SPEED_MASK) == XDEV_LS)
 #define DEV_HIGHSPEED(p)	(((p) & DEV_SPEED_MASK) == XDEV_HS)
 #define DEV_SUPERSPEED(p)	(((p) & DEV_SPEED_MASK) == XDEV_SS)
+#define DEV_SUPERSPEEDPLUS(p)	(((p) & DEV_SPEED_MASK) == XDEV_SSP)
+#define DEV_SUPERSPEED_ANY(p)	(((p) & DEV_SPEED_MASK) >= XDEV_SS)
+
 /* Bits 20:23 in the Slot Context are the speed for the device */
 #define	SLOT_SPEED_FS		(XDEV_FS << 10)
 #define	SLOT_SPEED_LS		(XDEV_LS << 10)