Commit 24ee65e4 authored by Mark Brown's avatar Mark Brown

Merge remote-tracking branches 'regulator/topic/s5m8767',...

Merge remote-tracking branches 'regulator/topic/s5m8767', 'regulator/topic/st-pwm', 'regulator/topic/ti-abb', 'regulator/topic/tps51632', 'regulator/topic/tps62360', 'regulator/topic/tps6507x', 'regulator/topic/tps65090' and 'regulator/topic/tps65217' into regulator-next
......@@ -69,13 +69,16 @@ sub-node should be of the format as listed below.
};
};
The above regulator entries are defined in regulator bindings documentation
except op_mode description.
except these properties:
- op_mode: describes the different operating modes of the LDO's with
power mode change in SOC. The different possible values are,
0 - always off mode
1 - on in normal mode
2 - low power mode
3 - suspend mode
- s5m8767,pmic-ext-control-gpios: (optional) GPIO specifier for one
GPIO controlling this regulator (enable/disable); This is
valid only for buck9.
The following are the names of the regulators that the s5m8767 pmic block
supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number
......@@ -148,5 +151,13 @@ Example:
regulator-always-on;
regulator-boot-on;
};
vemmc_reg: BUCK9 {
regulator-name = "VMEM_VDD_2.8V";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
op_mode = <3>; /* Standby Mode */
s5m8767,pmic-ext-control-gpios = <&gpk0 2 0>;
};
};
};
......@@ -4,10 +4,14 @@ Required Properties:
- compatible: Should be one of:
- "ti,abb-v1" for older SoCs like OMAP3
- "ti,abb-v2" for newer SoCs like OMAP4, OMAP5
- "ti,abb-v3" for a generic definition where setup and control registers are
provided (example: DRA7)
- reg: Address and length of the register set for the device. It contains
the information of registers in the same order as described by reg-names
- reg-names: Should contain the reg names
- "base-address" - contains base address of ABB module
- "base-address" - contains base address of ABB module (ti,abb-v1,ti,abb-v2)
- "control-address" - contains control register address of ABB module (ti,abb-v3)
- "setup-address" - contains setup register address of ABB module (ti,abb-v3)
- "int-address" - contains address of interrupt register for ABB module
(also see Optional properties)
- #address-cell: should be 0
......
......@@ -448,6 +448,12 @@ config REGULATOR_S5M8767
via I2C bus. S5M8767A have 9 Bucks and 28 LDOs output and
supports DVS mode with 8bits of output voltage control.
config REGULATOR_ST_PWM
tristate "STMicroelectronics PWM voltage regulator"
depends on ARCH_STI
help
This driver supports ST's PWM controlled voltage regulators.
config REGULATOR_TI_ABB
tristate "TI Adaptive Body Bias on-chip LDO"
depends on ARCH_OMAP
......
......@@ -61,6 +61,7 @@ obj-$(CONFIG_REGULATOR_RC5T583) += rc5t583-regulator.o
obj-$(CONFIG_REGULATOR_S2MPA01) += s2mpa01.o
obj-$(CONFIG_REGULATOR_S2MPS11) += s2mps11.o
obj-$(CONFIG_REGULATOR_S5M8767) += s5m8767.o
obj-$(CONFIG_REGULATOR_ST_PWM) += st-pwm.o
obj-$(CONFIG_REGULATOR_STW481X_VMMC) += stw481x-vmmc.o
obj-$(CONFIG_REGULATOR_TI_ABB) += ti-abb-regulator.o
obj-$(CONFIG_REGULATOR_TPS6105X) += tps6105x-regulator.o
......
......@@ -11,11 +11,8 @@
*
*/
#include <linux/bug.h>
#include <linux/err.h>
#include <linux/gpio.h>
#include <linux/of_gpio.h>
#include <linux/slab.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/regulator/driver.h>
......@@ -170,12 +167,11 @@ static unsigned int s5m8767_opmode_reg[][4] = {
{0x0, 0x3, 0x1, 0x1}, /* BUCK9 */
};
static int s5m8767_get_register(struct regulator_dev *rdev, int *reg,
int *enable_ctrl)
static int s5m8767_get_register(struct s5m8767_info *s5m8767, int reg_id,
int *reg, int *enable_ctrl)
{
int i, reg_id = rdev_get_id(rdev);
int i;
unsigned int mode;
struct s5m8767_info *s5m8767 = rdev_get_drvdata(rdev);
switch (reg_id) {
case S5M8767_LDO1 ... S5M8767_LDO2:
......@@ -214,53 +210,6 @@ static int s5m8767_get_register(struct regulator_dev *rdev, int *reg,
return 0;
}
static int s5m8767_reg_is_enabled(struct regulator_dev *rdev)
{
struct s5m8767_info *s5m8767 = rdev_get_drvdata(rdev);
int ret, reg;
int enable_ctrl;
unsigned int val;
ret = s5m8767_get_register(rdev, &reg, &enable_ctrl);
if (ret == -EINVAL)
return 1;
else if (ret)
return ret;
ret = regmap_read(s5m8767->iodev->regmap_pmic, reg, &val);
if (ret)
return ret;
return (val & S5M8767_ENCTRL_MASK) == enable_ctrl;
}
static int s5m8767_reg_enable(struct regulator_dev *rdev)
{
struct s5m8767_info *s5m8767 = rdev_get_drvdata(rdev);
int ret, reg;
int enable_ctrl;
ret = s5m8767_get_register(rdev, &reg, &enable_ctrl);
if (ret)
return ret;
return regmap_update_bits(s5m8767->iodev->regmap_pmic, reg,
S5M8767_ENCTRL_MASK, enable_ctrl);
}
static int s5m8767_reg_disable(struct regulator_dev *rdev)
{
struct s5m8767_info *s5m8767 = rdev_get_drvdata(rdev);
int ret, reg, enable_ctrl;
ret = s5m8767_get_register(rdev, &reg, &enable_ctrl);
if (ret)
return ret;
return regmap_update_bits(s5m8767->iodev->regmap_pmic, reg,
S5M8767_ENCTRL_MASK, ~S5M8767_ENCTRL_MASK);
}
static int s5m8767_get_vsel_reg(int reg_id, struct s5m8767_info *s5m8767)
{
int reg;
......@@ -410,9 +359,9 @@ static int s5m8767_set_voltage_time_sel(struct regulator_dev *rdev,
static struct regulator_ops s5m8767_ops = {
.list_voltage = regulator_list_voltage_linear,
.is_enabled = s5m8767_reg_is_enabled,
.enable = s5m8767_reg_enable,
.disable = s5m8767_reg_disable,
.is_enabled = regulator_is_enabled_regmap,
.enable = regulator_enable_regmap,
.disable = regulator_disable_regmap,
.get_voltage_sel = regulator_get_voltage_sel_regmap,
.set_voltage_sel = s5m8767_set_voltage_sel,
.set_voltage_time_sel = s5m8767_set_voltage_time_sel,
......@@ -420,9 +369,9 @@ static struct regulator_ops s5m8767_ops = {
static struct regulator_ops s5m8767_buck78_ops = {
.list_voltage = regulator_list_voltage_linear,
.is_enabled = s5m8767_reg_is_enabled,
.enable = s5m8767_reg_enable,
.disable = s5m8767_reg_disable,
.is_enabled = regulator_is_enabled_regmap,
.enable = regulator_enable_regmap,
.disable = regulator_disable_regmap,
.get_voltage_sel = regulator_get_voltage_sel_regmap,
.set_voltage_sel = regulator_set_voltage_sel_regmap,
};
......@@ -483,6 +432,66 @@ static struct regulator_desc regulators[] = {
s5m8767_regulator_desc(BUCK9),
};
/*
* Enable GPIO control over BUCK9 in regulator_config for that regulator.
*/
static void s5m8767_regulator_config_ext_control(struct s5m8767_info *s5m8767,
struct sec_regulator_data *rdata,
struct regulator_config *config)
{
int i, mode = 0;
if (rdata->id != S5M8767_BUCK9)
return;
/* Check if opmode for regulator matches S5M8767_ENCTRL_USE_GPIO */
for (i = 0; i < s5m8767->num_regulators; i++) {
const struct sec_opmode_data *opmode = &s5m8767->opmode[i];
if (opmode->id == rdata->id) {
mode = s5m8767_opmode_reg[rdata->id][opmode->mode];
break;
}
}
if (mode != S5M8767_ENCTRL_USE_GPIO) {
dev_warn(s5m8767->dev,
"ext-control for %s: mismatched op_mode (%x), ignoring\n",
rdata->reg_node->name, mode);
return;
}
if (!gpio_is_valid(rdata->ext_control_gpio)) {
dev_warn(s5m8767->dev,
"ext-control for %s: GPIO not valid, ignoring\n",
rdata->reg_node->name);
return;
}
config->ena_gpio = rdata->ext_control_gpio;
config->ena_gpio_flags = GPIOF_OUT_INIT_HIGH;
}
/*
* Turn on GPIO control over BUCK9.
*/
static int s5m8767_enable_ext_control(struct s5m8767_info *s5m8767,
struct regulator_dev *rdev)
{
int id = rdev_get_id(rdev);
int ret, reg, enable_ctrl;
if (id != S5M8767_BUCK9)
return -EINVAL;
ret = s5m8767_get_register(s5m8767, id, &reg, &enable_ctrl);
if (ret)
return ret;
return regmap_update_bits(s5m8767->iodev->regmap_pmic,
reg, S5M8767_ENCTRL_MASK,
S5M8767_ENCTRL_USE_GPIO << S5M8767_ENCTRL_SHIFT);
}
#ifdef CONFIG_OF
static int s5m8767_pmic_dt_parse_dvs_gpio(struct sec_pmic_dev *iodev,
struct sec_platform_data *pdata,
......@@ -520,6 +529,16 @@ static int s5m8767_pmic_dt_parse_ds_gpio(struct sec_pmic_dev *iodev,
return 0;
}
static void s5m8767_pmic_dt_parse_ext_control_gpio(struct sec_pmic_dev *iodev,
struct sec_regulator_data *rdata,
struct device_node *reg_np)
{
rdata->ext_control_gpio = of_get_named_gpio(reg_np,
"s5m8767,pmic-ext-control-gpios", 0);
if (!gpio_is_valid(rdata->ext_control_gpio))
rdata->ext_control_gpio = 0;
}
static int s5m8767_pmic_dt_parse_pdata(struct platform_device *pdev,
struct sec_platform_data *pdata)
{
......@@ -546,19 +565,13 @@ static int s5m8767_pmic_dt_parse_pdata(struct platform_device *pdev,
rdata = devm_kzalloc(&pdev->dev, sizeof(*rdata) *
pdata->num_regulators, GFP_KERNEL);
if (!rdata) {
dev_err(iodev->dev,
"could not allocate memory for regulator data\n");
if (!rdata)
return -ENOMEM;
}
rmode = devm_kzalloc(&pdev->dev, sizeof(*rmode) *
pdata->num_regulators, GFP_KERNEL);
if (!rmode) {
dev_err(iodev->dev,
"could not allocate memory for regulator mode\n");
if (!rmode)
return -ENOMEM;
}
pdata->regulators = rdata;
pdata->opmode = rmode;
......@@ -574,6 +587,8 @@ static int s5m8767_pmic_dt_parse_pdata(struct platform_device *pdev,
continue;
}
s5m8767_pmic_dt_parse_ext_control_gpio(iodev, rdata, reg_np);
rdata->id = i;
rdata->initdata = of_get_regulator_init_data(
&pdev->dev, reg_np);
......@@ -922,6 +937,7 @@ static int s5m8767_pmic_probe(struct platform_device *pdev)
for (i = 0; i < pdata->num_regulators; i++) {
const struct sec_voltage_desc *desc;
int id = pdata->regulators[i].id;
int enable_reg, enable_val;
desc = reg_voltage_map[id];
if (desc) {
......@@ -935,6 +951,12 @@ static int s5m8767_pmic_probe(struct platform_device *pdev)
regulators[id].vsel_mask = 0x3f;
else
regulators[id].vsel_mask = 0xff;
s5m8767_get_register(s5m8767, id, &enable_reg,
&enable_val);
regulators[id].enable_reg = enable_reg;
regulators[id].enable_mask = S5M8767_ENCTRL_MASK;
regulators[id].enable_val = enable_val;
}
config.dev = s5m8767->dev;
......@@ -942,6 +964,9 @@ static int s5m8767_pmic_probe(struct platform_device *pdev)
config.driver_data = s5m8767;
config.regmap = iodev->regmap_pmic;
config.of_node = pdata->regulators[i].reg_node;
if (pdata->regulators[i].ext_control_gpio)
s5m8767_regulator_config_ext_control(s5m8767,
&pdata->regulators[i], &config);
rdev[i] = devm_regulator_register(&pdev->dev, &regulators[id],
&config);
......@@ -951,6 +976,16 @@ static int s5m8767_pmic_probe(struct platform_device *pdev)
id);
return ret;
}
if (pdata->regulators[i].ext_control_gpio) {
ret = s5m8767_enable_ext_control(s5m8767, rdev[i]);
if (ret < 0) {
dev_err(s5m8767->dev,
"failed to enable gpio control over %s: %d\n",
rdev[i]->desc->name, ret);
return ret;
}
}
}
return 0;
......
/*
* Regulator driver for ST's PWM Regulators
*
* Copyright (C) 2014 - STMicroelectronics Inc.
*
* Author: Lee Jones <lee.jones@linaro.org>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/module.h>
#include <linux/init.h>
#include <linux/err.h>
#include <linux/regulator/driver.h>
#include <linux/regulator/machine.h>
#include <linux/regulator/of_regulator.h>
#include <linux/of.h>
#include <linux/of_device.h>
#include <linux/pwm.h>
#define ST_PWM_REG_PERIOD 8448
struct st_pwm_regulator_pdata {
const struct regulator_desc *desc;
struct st_pwm_voltages *duty_cycle_table;
};
struct st_pwm_regulator_data {
const struct st_pwm_regulator_pdata *pdata;
struct pwm_device *pwm;
bool enabled;
int state;
};
struct st_pwm_voltages {
unsigned int uV;
unsigned int dutycycle;
};
static int st_pwm_regulator_get_voltage_sel(struct regulator_dev *dev)
{
struct st_pwm_regulator_data *drvdata = rdev_get_drvdata(dev);
return drvdata->state;
}
static int st_pwm_regulator_set_voltage_sel(struct regulator_dev *dev,
unsigned selector)
{
struct st_pwm_regulator_data *drvdata = rdev_get_drvdata(dev);
int dutycycle;
int ret;
dutycycle = (ST_PWM_REG_PERIOD / 100) *
drvdata->pdata->duty_cycle_table[selector].dutycycle;
ret = pwm_config(drvdata->pwm, dutycycle, ST_PWM_REG_PERIOD);
if (ret) {
dev_err(&dev->dev, "Failed to configure PWM\n");
return ret;
}
drvdata->state = selector;
if (!drvdata->enabled) {
ret = pwm_enable(drvdata->pwm);
if (ret) {
dev_err(&dev->dev, "Failed to enable PWM\n");
return ret;
}
drvdata->enabled = true;
}
return 0;
}
static int st_pwm_regulator_list_voltage(struct regulator_dev *dev,
unsigned selector)
{
struct st_pwm_regulator_data *drvdata = rdev_get_drvdata(dev);
if (selector >= dev->desc->n_voltages)
return -EINVAL;
return drvdata->pdata->duty_cycle_table[selector].uV;
}
static struct regulator_ops st_pwm_regulator_voltage_ops = {
.set_voltage_sel = st_pwm_regulator_set_voltage_sel,
.get_voltage_sel = st_pwm_regulator_get_voltage_sel,
.list_voltage = st_pwm_regulator_list_voltage,
.map_voltage = regulator_map_voltage_iterate,
};
static struct st_pwm_voltages b2105_duty_cycle_table[] = {
{ .uV = 1114000, .dutycycle = 0, },
{ .uV = 1095000, .dutycycle = 10, },
{ .uV = 1076000, .dutycycle = 20, },
{ .uV = 1056000, .dutycycle = 30, },
{ .uV = 1036000, .dutycycle = 40, },
{ .uV = 1016000, .dutycycle = 50, },
/* WARNING: Values above 50% duty-cycle cause boot failures. */
};
static const struct regulator_desc b2105_desc = {
.name = "b2105-pwm-regulator",
.ops = &st_pwm_regulator_voltage_ops,
.type = REGULATOR_VOLTAGE,
.owner = THIS_MODULE,
.n_voltages = ARRAY_SIZE(b2105_duty_cycle_table),
.supply_name = "pwm",
};
static const struct st_pwm_regulator_pdata b2105_info = {
.desc = &b2105_desc,
.duty_cycle_table = b2105_duty_cycle_table,
};
static struct of_device_id st_pwm_of_match[] = {
{ .compatible = "st,b2105-pwm-regulator", .data = &b2105_info, },
{ },
};
MODULE_DEVICE_TABLE(of, st_pwm_of_match);
static int st_pwm_regulator_probe(struct platform_device *pdev)
{
struct st_pwm_regulator_data *drvdata;
struct regulator_dev *regulator;
struct regulator_config config = { };
struct device_node *np = pdev->dev.of_node;
const struct of_device_id *of_match;
if (!np) {
dev_err(&pdev->dev, "Device Tree node missing\n");
return -EINVAL;
}
drvdata = devm_kzalloc(&pdev->dev, sizeof(*drvdata), GFP_KERNEL);
if (!drvdata)
return -ENOMEM;
of_match = of_match_device(st_pwm_of_match, &pdev->dev);
if (!of_match) {
dev_err(&pdev->dev, "failed to match of device\n");
return -ENODEV;
}
drvdata->pdata = of_match->data;
config.init_data = of_get_regulator_init_data(&pdev->dev, np);
if (!config.init_data)
return -ENOMEM;
config.of_node = np;
config.dev = &pdev->dev;
config.driver_data = drvdata;
drvdata->pwm = devm_pwm_get(&pdev->dev, NULL);
if (IS_ERR(drvdata->pwm)) {
dev_err(&pdev->dev, "Failed to get PWM\n");
return PTR_ERR(drvdata->pwm);
}
regulator = devm_regulator_register(&pdev->dev,
drvdata->pdata->desc, &config);
if (IS_ERR(regulator)) {
dev_err(&pdev->dev, "Failed to register regulator %s\n",
drvdata->pdata->desc->name);
return PTR_ERR(regulator);
}
return 0;
}
static struct platform_driver st_pwm_regulator_driver = {
.driver = {
.name = "st-pwm-regulator",
.owner = THIS_MODULE,
.of_match_table = of_match_ptr(st_pwm_of_match),
},
.probe = st_pwm_regulator_probe,
};
module_platform_driver(st_pwm_regulator_driver);
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Lee Jones <lee.jones@linaro.org>");
MODULE_DESCRIPTION("ST PWM Regulator Driver");
MODULE_ALIAS("platform:st_pwm-regulator");
......@@ -54,8 +54,8 @@ struct ti_abb_info {
/**
* struct ti_abb_reg - Register description for ABB block
* @setup_reg: setup register offset from base
* @control_reg: control register offset from base
* @setup_off: setup register offset from base
* @control_off: control register offset from base
* @sr2_wtcnt_value_mask: setup register- sr2_wtcnt_value mask
* @fbb_sel_mask: setup register- FBB sel mask
* @rbb_sel_mask: setup register- RBB sel mask
......@@ -64,8 +64,8 @@ struct ti_abb_info {
* @opp_sel_mask: control register - mask for mode to operate
*/
struct ti_abb_reg {
u32 setup_reg;
u32 control_reg;
u32 setup_off;
u32 control_off;
/* Setup register fields */
u32 sr2_wtcnt_value_mask;
......@@ -83,6 +83,8 @@ struct ti_abb_reg {
* @rdesc: regulator descriptor
* @clk: clock(usually sysclk) supplying ABB block
* @base: base address of ABB block
* @setup_reg: setup register of ABB block
* @control_reg: control register of ABB block
* @int_base: interrupt register base address
* @efuse_base: (optional) efuse base address for ABB modes
* @ldo_base: (optional) LDOVBB vset override base address
......@@ -99,6 +101,8 @@ struct ti_abb {
struct regulator_desc rdesc;
struct clk *clk;
void __iomem *base;
void __iomem *setup_reg;
void __iomem *control_reg;
void __iomem *int_base;
void __iomem *efuse_base;
void __iomem *ldo_base;
......@@ -118,20 +122,18 @@ struct ti_abb {
* ti_abb_rmw() - handy wrapper to set specific register bits
* @mask: mask for register field
* @value: value shifted to mask location and written
* @offset: offset of register
* @base: base address
* @reg: register address
*
* Return: final register value (may be unused)
*/
static inline u32 ti_abb_rmw(u32 mask, u32 value, u32 offset,
void __iomem *base)
static inline u32 ti_abb_rmw(u32 mask, u32 value, void __iomem *reg)
{
u32 val;
val = readl(base + offset);
val = readl(reg);
val &= ~mask;
val |= (value << __ffs(mask)) & mask;
writel(val, base + offset);
writel(val, reg);
return val;
}
......@@ -263,21 +265,19 @@ static int ti_abb_set_opp(struct regulator_dev *rdev, struct ti_abb *abb,
if (ret)
goto out;
ti_abb_rmw(regs->fbb_sel_mask | regs->rbb_sel_mask, 0, regs->setup_reg,
abb->base);
ti_abb_rmw(regs->fbb_sel_mask | regs->rbb_sel_mask, 0, abb->setup_reg);
switch (info->opp_sel) {
case TI_ABB_SLOW_OPP:
ti_abb_rmw(regs->rbb_sel_mask, 1, regs->setup_reg, abb->base);
ti_abb_rmw(regs->rbb_sel_mask, 1, abb->setup_reg);
break;
case TI_ABB_FAST_OPP:
ti_abb_rmw(regs->fbb_sel_mask, 1, regs->setup_reg, abb->base);
ti_abb_rmw(regs->fbb_sel_mask, 1, abb->setup_reg);
break;
}
/* program next state of ABB ldo */
ti_abb_rmw(regs->opp_sel_mask, info->opp_sel, regs->control_reg,
abb->base);
ti_abb_rmw(regs->opp_sel_mask, info->opp_sel, abb->control_reg);
/*
* program LDO VBB vset override if needed for !bypass mode
......@@ -288,7 +288,7 @@ static int ti_abb_set_opp(struct regulator_dev *rdev, struct ti_abb *abb,
ti_abb_program_ldovbb(dev, abb, info);
/* Initiate ABB ldo change */
ti_abb_rmw(regs->opp_change_mask, 1, regs->control_reg, abb->base);
ti_abb_rmw(regs->opp_change_mask, 1, abb->control_reg);
/* Wait for ABB LDO to complete transition to new Bias setting */
ret = ti_abb_wait_txdone(dev, abb);
......@@ -490,8 +490,7 @@ static int ti_abb_init_timings(struct device *dev, struct ti_abb *abb)
dev_dbg(dev, "%s: Clk_rate=%ld, sr2_cnt=0x%08x\n", __func__,
clk_get_rate(abb->clk), sr2_wt_cnt_val);
ti_abb_rmw(regs->sr2_wtcnt_value_mask, sr2_wt_cnt_val, regs->setup_reg,
abb->base);
ti_abb_rmw(regs->sr2_wtcnt_value_mask, sr2_wt_cnt_val, abb->setup_reg);
return 0;
}
......@@ -508,32 +507,24 @@ static int ti_abb_init_table(struct device *dev, struct ti_abb *abb,
struct regulator_init_data *rinit_data)
{
struct ti_abb_info *info;
const struct property *prop;
const __be32 *abb_info;
const u32 num_values = 6;
char *pname = "ti,abb_info";
u32 num_entries, i;
u32 i;
unsigned int *volt_table;
int min_uV = INT_MAX, max_uV = 0;
int num_entries, min_uV = INT_MAX, max_uV = 0;
struct regulation_constraints *c = &rinit_data->constraints;
prop = of_find_property(dev->of_node, pname, NULL);
if (!prop) {
dev_err(dev, "No '%s' property?\n", pname);
return -ENODEV;
}
if (!prop->value) {
dev_err(dev, "Empty '%s' property?\n", pname);
return -ENODATA;
}
/*
* Each abb_info is a set of n-tuple, where n is num_values, consisting
* of voltage and a set of detection logic for ABB information for that
* voltage to apply.
*/
num_entries = prop->length / sizeof(u32);
num_entries = of_property_count_u32_elems(dev->of_node, pname);
if (num_entries < 0) {
dev_err(dev, "No '%s' property?\n", pname);
return num_entries;
}
if (!num_entries || (num_entries % num_values)) {
dev_err(dev, "All '%s' list entries need %d vals\n", pname,
num_values);
......@@ -542,38 +533,38 @@ static int ti_abb_init_table(struct device *dev, struct ti_abb *abb,
num_entries /= num_values;
info = devm_kzalloc(dev, sizeof(*info) * num_entries, GFP_KERNEL);
if (!info) {
dev_err(dev, "Can't allocate info table for '%s' property\n",
pname);
if (!info)
return -ENOMEM;
}
abb->info = info;
volt_table = devm_kzalloc(dev, sizeof(unsigned int) * num_entries,
GFP_KERNEL);
if (!volt_table) {
dev_err(dev, "Can't allocate voltage table for '%s' property\n",
pname);
if (!volt_table)
return -ENOMEM;
}
abb->rdesc.n_voltages = num_entries;
abb->rdesc.volt_table = volt_table;
/* We do not know where the OPP voltage is at the moment */
abb->current_info_idx = -EINVAL;
abb_info = prop->value;
for (i = 0; i < num_entries; i++, info++, volt_table++) {
u32 efuse_offset, rbb_mask, fbb_mask, vset_mask;
u32 efuse_val;
/* NOTE: num_values should equal to entries picked up here */
*volt_table = be32_to_cpup(abb_info++);
info->opp_sel = be32_to_cpup(abb_info++);
efuse_offset = be32_to_cpup(abb_info++);
rbb_mask = be32_to_cpup(abb_info++);
fbb_mask = be32_to_cpup(abb_info++);
vset_mask = be32_to_cpup(abb_info++);
of_property_read_u32_index(dev->of_node, pname, i * num_values,
volt_table);
of_property_read_u32_index(dev->of_node, pname,
i * num_values + 1, &info->opp_sel);
of_property_read_u32_index(dev->of_node, pname,
i * num_values + 2, &efuse_offset);
of_property_read_u32_index(dev->of_node, pname,
i * num_values + 3, &rbb_mask);
of_property_read_u32_index(dev->of_node, pname,
i * num_values + 4, &fbb_mask);
of_property_read_u32_index(dev->of_node, pname,
i * num_values + 5, &vset_mask);
dev_dbg(dev,
"[%d]v=%d ABB=%d ef=0x%x rbb=0x%x fbb=0x%x vset=0x%x\n",
......@@ -648,8 +639,8 @@ static struct regulator_ops ti_abb_reg_ops = {
/* Default ABB block offsets, IF this changes in future, create new one */
static const struct ti_abb_reg abb_regs_v1 = {
/* WARNING: registers are wrongly documented in TRM */
.setup_reg = 0x04,
.control_reg = 0x00,
.setup_off = 0x04,
.control_off = 0x00,
.sr2_wtcnt_value_mask = (0xff << 8),
.fbb_sel_mask = (0x01 << 2),
......@@ -661,8 +652,8 @@ static const struct ti_abb_reg abb_regs_v1 = {
};
static const struct ti_abb_reg abb_regs_v2 = {
.setup_reg = 0x00,
.control_reg = 0x04,
.setup_off = 0x00,
.control_off = 0x04,
.sr2_wtcnt_value_mask = (0xff << 8),
.fbb_sel_mask = (0x01 << 2),
......@@ -673,9 +664,20 @@ static const struct ti_abb_reg abb_regs_v2 = {
.opp_sel_mask = (0x03 << 0),
};
static const struct ti_abb_reg abb_regs_generic = {
.sr2_wtcnt_value_mask = (0xff << 8),
.fbb_sel_mask = (0x01 << 2),
.rbb_sel_mask = (0x01 << 1),
.sr2_en_mask = (0x01 << 0),
.opp_change_mask = (0x01 << 2),
.opp_sel_mask = (0x03 << 0),
};
static const struct of_device_id ti_abb_of_match[] = {
{.compatible = "ti,abb-v1", .data = &abb_regs_v1},
{.compatible = "ti,abb-v2", .data = &abb_regs_v2},
{.compatible = "ti,abb-v3", .data = &abb_regs_generic},
{ },
};
......@@ -722,12 +724,30 @@ static int ti_abb_probe(struct platform_device *pdev)
abb->regs = match->data;
/* Map ABB resources */
if (abb->regs->setup_off || abb->regs->control_off) {
pname = "base-address";
res = platform_get_resource_byname(pdev, IORESOURCE_MEM, pname);
abb->base = devm_ioremap_resource(dev, res);
if (IS_ERR(abb->base))
return PTR_ERR(abb->base);
abb->setup_reg = abb->base + abb->regs->setup_off;
abb->control_reg = abb->base + abb->regs->control_off;
} else {
pname = "control-address";
res = platform_get_resource_byname(pdev, IORESOURCE_MEM, pname);
abb->control_reg = devm_ioremap_resource(dev, res);
if (IS_ERR(abb->control_reg))
return PTR_ERR(abb->control_reg);
pname = "setup-address";
res = platform_get_resource_byname(pdev, IORESOURCE_MEM, pname);
abb->setup_reg = devm_ioremap_resource(dev, res);
if (IS_ERR(abb->setup_reg))
return PTR_ERR(abb->setup_reg);
}
pname = "int-address";
res = platform_get_resource_byname(pdev, IORESOURCE_MEM, pname);
if (!res) {
......@@ -860,7 +880,7 @@ static int ti_abb_probe(struct platform_device *pdev)
platform_set_drvdata(pdev, rdev);
/* Enable the ldo if not already done by bootloader */
ti_abb_rmw(abb->regs->sr2_en_mask, 1, abb->regs->setup_reg, abb->base);
ti_abb_rmw(abb->regs->sr2_en_mask, 1, abb->setup_reg);
return 0;
}
......
......@@ -227,10 +227,8 @@ static struct tps51632_regulator_platform_data *
struct device_node *np = dev->of_node;
pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
if (!pdata) {
dev_err(dev, "Memory alloc failed for platform data\n");
if (!pdata)
return NULL;
}
pdata->reg_init_data = of_get_regulator_init_data(dev, dev->of_node);
if (!pdata->reg_init_data) {
......@@ -299,10 +297,8 @@ static int tps51632_probe(struct i2c_client *client,
}
tps = devm_kzalloc(&client->dev, sizeof(*tps), GFP_KERNEL);
if (!tps) {
dev_err(&client->dev, "Memory allocation failed\n");
if (!tps)
return -ENOMEM;
}
tps->dev = &client->dev;
tps->desc.name = client->name;
......
......@@ -299,10 +299,8 @@ static struct tps62360_regulator_platform_data *
struct device_node *np = dev->of_node;
pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
if (!pdata) {
dev_err(dev, "Memory alloc failed for platform data\n");
if (!pdata)
return NULL;
}
pdata->reg_init_data = of_get_regulator_init_data(dev, dev->of_node);
if (!pdata->reg_init_data) {
......@@ -377,11 +375,8 @@ static int tps62360_probe(struct i2c_client *client,
}
tps = devm_kzalloc(&client->dev, sizeof(*tps), GFP_KERNEL);
if (!tps) {
dev_err(&client->dev, "%s(): Memory allocation failed\n",
__func__);
if (!tps)
return -ENOMEM;
}
tps->en_discharge = pdata->en_discharge;
tps->en_internal_pulldn = pdata->en_internal_pulldn;
......
......@@ -359,7 +359,6 @@ static struct regulator_ops tps6507x_pmic_ops = {
.map_voltage = regulator_map_voltage_ascend,
};
#ifdef CONFIG_OF
static struct of_regulator_match tps6507x_matches[] = {
{ .name = "VDCDC1"},
{ .name = "VDCDC2"},
......@@ -381,12 +380,10 @@ static struct tps6507x_board *tps6507x_parse_dt_reg_data(
tps_board = devm_kzalloc(&pdev->dev, sizeof(*tps_board),
GFP_KERNEL);
if (!tps_board) {
dev_err(&pdev->dev, "Failure to alloc pdata for regulators.\n");
if (!tps_board)
return NULL;
}
regulators = of_find_node_by_name(np, "regulators");
regulators = of_get_child_by_name(np, "regulators");
if (!regulators) {
dev_err(&pdev->dev, "regulator node not found\n");
return NULL;
......@@ -396,6 +393,7 @@ static struct tps6507x_board *tps6507x_parse_dt_reg_data(
matches = tps6507x_matches;
ret = of_regulator_match(&pdev->dev, regulators, matches, count);
of_node_put(regulators);
if (ret < 0) {
dev_err(&pdev->dev, "Error parsing regulator init data: %d\n",
ret);
......@@ -406,10 +404,8 @@ static struct tps6507x_board *tps6507x_parse_dt_reg_data(
reg_data = devm_kzalloc(&pdev->dev, (sizeof(struct regulator_init_data)
* TPS6507X_NUM_REGULATOR), GFP_KERNEL);
if (!reg_data) {
dev_err(&pdev->dev, "Failure to alloc init data for regulators.\n");
if (!reg_data)
return NULL;
}
tps_board->tps6507x_pmic_init_data = reg_data;
......@@ -424,15 +420,7 @@ static struct tps6507x_board *tps6507x_parse_dt_reg_data(
return tps_board;
}
#else
static inline struct tps6507x_board *tps6507x_parse_dt_reg_data(
struct platform_device *pdev,
struct of_regulator_match **tps6507x_reg_matches)
{
*tps6507x_reg_matches = NULL;
return NULL;
}
#endif
static int tps6507x_pmic_probe(struct platform_device *pdev)
{
struct tps6507x_dev *tps6507x_dev = dev_get_drvdata(pdev->dev.parent);
......@@ -453,7 +441,8 @@ static int tps6507x_pmic_probe(struct platform_device *pdev)
*/
tps_board = dev_get_platdata(tps6507x_dev->dev);
if (!tps_board && tps6507x_dev->dev->of_node)
if (IS_ENABLED(CONFIG_OF) && !tps_board &&
tps6507x_dev->dev->of_node)
tps_board = tps6507x_parse_dt_reg_data(pdev,
&tps6507x_reg_matches);
if (!tps_board)
......
......@@ -168,17 +168,13 @@ static struct tps65090_platform_data *tps65090_parse_dt_reg_data(
tps65090_pdata = devm_kzalloc(&pdev->dev, sizeof(*tps65090_pdata),
GFP_KERNEL);
if (!tps65090_pdata) {
dev_err(&pdev->dev, "Memory alloc for tps65090_pdata failed\n");
if (!tps65090_pdata)
return ERR_PTR(-ENOMEM);
}
reg_pdata = devm_kzalloc(&pdev->dev, TPS65090_REGULATOR_MAX *
sizeof(*reg_pdata), GFP_KERNEL);
if (!reg_pdata) {
dev_err(&pdev->dev, "Memory alloc for reg_pdata failed\n");
if (!reg_pdata)
return ERR_PTR(-ENOMEM);
}
regulators = of_get_child_by_name(np, "regulators");
if (!regulators) {
......@@ -188,6 +184,7 @@ static struct tps65090_platform_data *tps65090_parse_dt_reg_data(
ret = of_regulator_match(&pdev->dev, regulators, tps65090_matches,
ARRAY_SIZE(tps65090_matches));
of_node_put(regulators);
if (ret < 0) {
dev_err(&pdev->dev,
"Error parsing regulator init data: %d\n", ret);
......@@ -252,10 +249,8 @@ static int tps65090_regulator_probe(struct platform_device *pdev)
pmic = devm_kzalloc(&pdev->dev, TPS65090_REGULATOR_MAX * sizeof(*pmic),
GFP_KERNEL);
if (!pmic) {
dev_err(&pdev->dev, "mem alloc for pmic failed\n");
if (!pmic)
return -ENOMEM;
}
for (num = 0; num < TPS65090_REGULATOR_MAX; num++) {
tps_pdata = tps65090_pdata->reg_pdata[num];
......
......@@ -187,7 +187,7 @@ static struct tps65217_board *tps65217_parse_dt(struct platform_device *pdev)
struct device_node *regs;
int i, count;
regs = of_find_node_by_name(node, "regulators");
regs = of_get_child_by_name(node, "regulators");
if (!regs)
return NULL;
......@@ -202,7 +202,7 @@ static struct tps65217_board *tps65217_parse_dt(struct platform_device *pdev)
return NULL;
for (i = 0; i < count; i++) {
if (!reg_matches[i].init_data || !reg_matches[i].of_node)
if (!reg_matches[i].of_node)
continue;
pdata->tps65217_init_data[i] = reg_matches[i].init_data;
......@@ -222,7 +222,6 @@ static int tps65217_regulator_probe(struct platform_device *pdev)
{
struct tps65217 *tps = dev_get_drvdata(pdev->dev.parent);
struct tps65217_board *pdata = dev_get_platdata(tps->dev);
struct regulator_init_data *reg_data;
struct regulator_dev *rdev;
struct regulator_config config = { };
int i;
......@@ -243,19 +242,9 @@ static int tps65217_regulator_probe(struct platform_device *pdev)
platform_set_drvdata(pdev, tps);
for (i = 0; i < TPS65217_NUM_REGULATOR; i++) {
reg_data = pdata->tps65217_init_data[i];
/*
* Regulator API handles empty constraints but not NULL
* constraints
*/
if (!reg_data)
continue;
/* Register the regulators */
config.dev = tps->dev;
config.init_data = reg_data;
config.init_data = pdata->tps65217_init_data[i];
config.driver_data = tps;
config.regmap = tps->regmap;
if (tps->dev->of_node)
......
......@@ -127,6 +127,7 @@ struct sec_regulator_data {
int id;
struct regulator_init_data *initdata;
struct device_node *reg_node;
int ext_control_gpio;
};
/*
......
......@@ -183,9 +183,16 @@ enum s5m8767_regulators {
S5M8767_REG_MAX,
};
/* LDO_EN/BUCK_EN field in registers */
#define S5M8767_ENCTRL_SHIFT 6
#define S5M8767_ENCTRL_MASK (0x3 << S5M8767_ENCTRL_SHIFT)
/*
* LDO_EN/BUCK_EN register value for controlling this Buck or LDO
* by GPIO (PWREN, BUCKEN).
*/
#define S5M8767_ENCTRL_USE_GPIO 0x1
/*
* Values for BUCK_RAMP field in DVS_RAMP register, matching raw values
* in mV/us.
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment