Merge remote-tracking branches 'regulator/topic/s5m8767',...

Merge remote-tracking branches 'regulator/topic/s5m8767', 'regulator/topic/st-pwm', 'regulator/topic/ti-abb', 'regulator/topic/tps51632', 'regulator/topic/tps62360', 'regulator/topic/tps6507x', 'regulator/topic/tps65090' and 'regulator/topic/tps65217' into regulator-next

Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt

@@ -69,13 +69,16 @@ sub-node should be of the format as listed below.
 		};
 	};
 The above regulator entries are defined in regulator bindings documentation
-except op_mode description.
+except these properties:
 	- op_mode: describes the different operating modes of the LDO's with
 		power mode change in SOC. The different possible values are,
 		0 - always off mode
 		1 - on in normal mode
 		2 - low power mode
 		3 - suspend mode
+	- s5m8767,pmic-ext-control-gpios: (optional) GPIO specifier for one
+		GPIO controlling this regulator (enable/disable); This is
+		valid only for buck9.
 
 The following are the names of the regulators that the s5m8767 pmic block
 supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number
@@ -148,5 +151,13 @@ Example:
 				regulator-always-on;
 				regulator-boot-on;
 			};
+
+			vemmc_reg: BUCK9 {
+				regulator-name = "VMEM_VDD_2.8V";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				op_mode = <3>; /* Standby Mode */
+				s5m8767,pmic-ext-control-gpios = <&gpk0 2 0>;
+			};
 		};
 	};

Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt

@@ -4,10 +4,14 @@ Required Properties:
 - compatible: Should be one of:
   - "ti,abb-v1" for older SoCs like OMAP3
   - "ti,abb-v2" for newer SoCs like OMAP4, OMAP5
+  - "ti,abb-v3" for a generic definition where setup and control registers are
+     provided (example: DRA7)
 - reg: Address and length of the register set for the device. It contains
   the information of registers in the same order as described by reg-names
 - reg-names: Should contain the reg names
-  - "base-address"	- contains base address of ABB module
+  - "base-address"	- contains base address of ABB module (ti,abb-v1,ti,abb-v2)
+  - "control-address"	- contains control register address of ABB module (ti,abb-v3)
+  - "setup-address"	- contains setup register address of ABB module (ti,abb-v3)
   - "int-address"	- contains address of interrupt register for ABB module
   (also see Optional properties)
 - #address-cell: should be 0

drivers/regulator/Kconfig

@@ -448,6 +448,12 @@ config REGULATOR_S5M8767
 	 via I2C bus. S5M8767A have 9 Bucks and 28 LDOs output and
 	 supports DVS mode with 8bits of output voltage control.
 
+config REGULATOR_ST_PWM
+	tristate "STMicroelectronics PWM voltage regulator"
+	depends on ARCH_STI
+	help
+	 This driver supports ST's PWM controlled voltage regulators.
+
 config REGULATOR_TI_ABB
 	tristate "TI Adaptive Body Bias on-chip LDO"
 	depends on ARCH_OMAP

drivers/regulator/Makefile

@@ -61,6 +61,7 @@ obj-$(CONFIG_REGULATOR_RC5T583)  += rc5t583-regulator.o
 obj-$(CONFIG_REGULATOR_S2MPA01) += s2mpa01.o
 obj-$(CONFIG_REGULATOR_S2MPS11) += s2mps11.o
 obj-$(CONFIG_REGULATOR_S5M8767) += s5m8767.o
+obj-$(CONFIG_REGULATOR_ST_PWM) += st-pwm.o
 obj-$(CONFIG_REGULATOR_STW481X_VMMC) += stw481x-vmmc.o
 obj-$(CONFIG_REGULATOR_TI_ABB) += ti-abb-regulator.o
 obj-$(CONFIG_REGULATOR_TPS6105X) += tps6105x-regulator.o

drivers/regulator/s5m8767.c

@@ -11,11 +11,8 @@
  *
  */
 
-#include <linux/bug.h>
 #include <linux/err.h>
-#include <linux/gpio.h>
 #include <linux/of_gpio.h>
-#include <linux/slab.h>
 #include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/regulator/driver.h>
@@ -170,12 +167,11 @@ static unsigned int s5m8767_opmode_reg[][4] = {
 	{0x0, 0x3, 0x1, 0x1}, /* BUCK9 */
 };
 
-static int s5m8767_get_register(struct regulator_dev *rdev, int *reg,
-				int *enable_ctrl)
+static int s5m8767_get_register(struct s5m8767_info *s5m8767, int reg_id,
+				int *reg, int *enable_ctrl)
 {
-	int i, reg_id = rdev_get_id(rdev);
+	int i;
 	unsigned int mode;
-	struct s5m8767_info *s5m8767 = rdev_get_drvdata(rdev);
 
 	switch (reg_id) {
 	case S5M8767_LDO1 ... S5M8767_LDO2:
@@ -214,53 +210,6 @@ static int s5m8767_get_register(struct regulator_dev *rdev, int *reg,
 	return 0;
 }
 
-static int s5m8767_reg_is_enabled(struct regulator_dev *rdev)
-{
-	struct s5m8767_info *s5m8767 = rdev_get_drvdata(rdev);
-	int ret, reg;
-	int enable_ctrl;
-	unsigned int val;
-
-	ret = s5m8767_get_register(rdev, &reg, &enable_ctrl);
-	if (ret == -EINVAL)
-		return 1;
-	else if (ret)
-		return ret;
-
-	ret = regmap_read(s5m8767->iodev->regmap_pmic, reg, &val);
-	if (ret)
-		return ret;
-
-	return (val & S5M8767_ENCTRL_MASK) == enable_ctrl;
-}
-
-static int s5m8767_reg_enable(struct regulator_dev *rdev)
-{
-	struct s5m8767_info *s5m8767 = rdev_get_drvdata(rdev);
-	int ret, reg;
-	int enable_ctrl;
-
-	ret = s5m8767_get_register(rdev, &reg, &enable_ctrl);
-	if (ret)
-		return ret;
-
-	return regmap_update_bits(s5m8767->iodev->regmap_pmic, reg,
-			S5M8767_ENCTRL_MASK, enable_ctrl);
-}
-
-static int s5m8767_reg_disable(struct regulator_dev *rdev)
-{
-	struct s5m8767_info *s5m8767 = rdev_get_drvdata(rdev);
-	int ret, reg, enable_ctrl;
-
-	ret = s5m8767_get_register(rdev, &reg, &enable_ctrl);
-	if (ret)
-		return ret;
-
-	return regmap_update_bits(s5m8767->iodev->regmap_pmic, reg,
-			S5M8767_ENCTRL_MASK, ~S5M8767_ENCTRL_MASK);
-}
-
 static int s5m8767_get_vsel_reg(int reg_id, struct s5m8767_info *s5m8767)
 {
 	int reg;
@@ -410,9 +359,9 @@ static int s5m8767_set_voltage_time_sel(struct regulator_dev *rdev,
 
 static struct regulator_ops s5m8767_ops = {
 	.list_voltage		= regulator_list_voltage_linear,
-	.is_enabled		= s5m8767_reg_is_enabled,
-	.enable			= s5m8767_reg_enable,
-	.disable		= s5m8767_reg_disable,
+	.is_enabled		= regulator_is_enabled_regmap,
+	.enable			= regulator_enable_regmap,
+	.disable		= regulator_disable_regmap,
 	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
 	.set_voltage_sel	= s5m8767_set_voltage_sel,
 	.set_voltage_time_sel	= s5m8767_set_voltage_time_sel,
@@ -420,9 +369,9 @@ static struct regulator_ops s5m8767_ops = {
 
 static struct regulator_ops s5m8767_buck78_ops = {
 	.list_voltage		= regulator_list_voltage_linear,
-	.is_enabled		= s5m8767_reg_is_enabled,
-	.enable			= s5m8767_reg_enable,
-	.disable		= s5m8767_reg_disable,
+	.is_enabled		= regulator_is_enabled_regmap,
+	.enable			= regulator_enable_regmap,
+	.disable		= regulator_disable_regmap,
 	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
 	.set_voltage_sel	= regulator_set_voltage_sel_regmap,
 };
@@ -483,6 +432,66 @@ static struct regulator_desc regulators[] = {
 	s5m8767_regulator_desc(BUCK9),
 };
 
+/*
+ * Enable GPIO control over BUCK9 in regulator_config for that regulator.
+ */
+static void s5m8767_regulator_config_ext_control(struct s5m8767_info *s5m8767,
+		struct sec_regulator_data *rdata,
+		struct regulator_config *config)
+{
+	int i, mode = 0;
+
+	if (rdata->id != S5M8767_BUCK9)
+		return;
+
+	/* Check if opmode for regulator matches S5M8767_ENCTRL_USE_GPIO */
+	for (i = 0; i < s5m8767->num_regulators; i++) {
+		const struct sec_opmode_data *opmode = &s5m8767->opmode[i];
+		if (opmode->id == rdata->id) {
+			mode = s5m8767_opmode_reg[rdata->id][opmode->mode];
+			break;
+		}
+	}
+	if (mode != S5M8767_ENCTRL_USE_GPIO) {
+		dev_warn(s5m8767->dev,
+				"ext-control for %s: mismatched op_mode (%x), ignoring\n",
+				rdata->reg_node->name, mode);
+		return;
+	}
+
+	if (!gpio_is_valid(rdata->ext_control_gpio)) {
+		dev_warn(s5m8767->dev,
+				"ext-control for %s: GPIO not valid, ignoring\n",
+				rdata->reg_node->name);
+		return;
+	}
+
+	config->ena_gpio = rdata->ext_control_gpio;
+	config->ena_gpio_flags = GPIOF_OUT_INIT_HIGH;
+}
+
+/*
+ * Turn on GPIO control over BUCK9.
+ */
+static int s5m8767_enable_ext_control(struct s5m8767_info *s5m8767,
+		struct regulator_dev *rdev)
+{
+	int id = rdev_get_id(rdev);
+	int ret, reg, enable_ctrl;
+
+	if (id != S5M8767_BUCK9)
+		return -EINVAL;
+
+	ret = s5m8767_get_register(s5m8767, id, &reg, &enable_ctrl);
+	if (ret)
+		return ret;
+
+	return regmap_update_bits(s5m8767->iodev->regmap_pmic,
+			reg, S5M8767_ENCTRL_MASK,
+			S5M8767_ENCTRL_USE_GPIO << S5M8767_ENCTRL_SHIFT);
+}
+
+
 #ifdef CONFIG_OF
 static int s5m8767_pmic_dt_parse_dvs_gpio(struct sec_pmic_dev *iodev,
 			struct sec_platform_data *pdata,
@@ -520,6 +529,16 @@ static int s5m8767_pmic_dt_parse_ds_gpio(struct sec_pmic_dev *iodev,
 	return 0;
 }
 
+static void s5m8767_pmic_dt_parse_ext_control_gpio(struct sec_pmic_dev *iodev,
+		struct sec_regulator_data *rdata,
+		struct device_node *reg_np)
+{
+	rdata->ext_control_gpio = of_get_named_gpio(reg_np,
+			"s5m8767,pmic-ext-control-gpios", 0);
+	if (!gpio_is_valid(rdata->ext_control_gpio))
+		rdata->ext_control_gpio = 0;
+}
+
 static int s5m8767_pmic_dt_parse_pdata(struct platform_device *pdev,
 					struct sec_platform_data *pdata)
 {
@@ -546,19 +565,13 @@ static int s5m8767_pmic_dt_parse_pdata(struct platform_device *pdev,
 
 	rdata = devm_kzalloc(&pdev->dev, sizeof(*rdata) *
 				pdata->num_regulators, GFP_KERNEL);
-	if (!rdata) {
-		dev_err(iodev->dev,
-			"could not allocate memory for regulator data\n");
+	if (!rdata)
 		return -ENOMEM;
-	}
 
 	rmode = devm_kzalloc(&pdev->dev, sizeof(*rmode) *
 				pdata->num_regulators, GFP_KERNEL);
-	if (!rmode) {
-		dev_err(iodev->dev,
-			"could not allocate memory for regulator mode\n");
+	if (!rmode)
 		return -ENOMEM;
-	}
 
 	pdata->regulators = rdata;
 	pdata->opmode = rmode;
@@ -574,6 +587,8 @@ static int s5m8767_pmic_dt_parse_pdata(struct platform_device *pdev,
 			continue;
 		}
 
+		s5m8767_pmic_dt_parse_ext_control_gpio(iodev, rdata, reg_np);
+
 		rdata->id = i;
 		rdata->initdata = of_get_regulator_init_data(
 						&pdev->dev, reg_np);
@@ -922,6 +937,7 @@ static int s5m8767_pmic_probe(struct platform_device *pdev)
 	for (i = 0; i < pdata->num_regulators; i++) {
 		const struct sec_voltage_desc *desc;
 		int id = pdata->regulators[i].id;
+		int enable_reg, enable_val;
 
 		desc = reg_voltage_map[id];
 		if (desc) {
@@ -935,6 +951,12 @@ static int s5m8767_pmic_probe(struct platform_device *pdev)
 				regulators[id].vsel_mask = 0x3f;
 			else
 				regulators[id].vsel_mask = 0xff;
+
+			s5m8767_get_register(s5m8767, id, &enable_reg,
+					     &enable_val);
+			regulators[id].enable_reg = enable_reg;
+			regulators[id].enable_mask = S5M8767_ENCTRL_MASK;
+			regulators[id].enable_val = enable_val;
 		}
 
 		config.dev = s5m8767->dev;
@@ -942,6 +964,9 @@ static int s5m8767_pmic_probe(struct platform_device *pdev)
 		config.driver_data = s5m8767;
 		config.regmap = iodev->regmap_pmic;
 		config.of_node = pdata->regulators[i].reg_node;
+		if (pdata->regulators[i].ext_control_gpio)
+			s5m8767_regulator_config_ext_control(s5m8767,
+					&pdata->regulators[i], &config);
 
 		rdev[i] = devm_regulator_register(&pdev->dev, &regulators[id],
 						  &config);
@@ -951,6 +976,16 @@ static int s5m8767_pmic_probe(struct platform_device *pdev)
 					id);
 			return ret;
 		}
+
+		if (pdata->regulators[i].ext_control_gpio) {
+			ret = s5m8767_enable_ext_control(s5m8767, rdev[i]);
+			if (ret < 0) {
+				dev_err(s5m8767->dev,
+						"failed to enable gpio control over %s: %d\n",
+						rdev[i]->desc->name, ret);
+				return ret;
+			}
+		}
 	}
 
 	return 0;

drivers/regulator/st-pwm.c

+/*
+ * Regulator driver for ST's PWM Regulators
+ *
+ * Copyright (C) 2014 - STMicroelectronics Inc.
+ *
+ * Author: Lee Jones <lee.jones@linaro.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/err.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/of_regulator.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pwm.h>
+
+#define ST_PWM_REG_PERIOD 8448
+
+struct st_pwm_regulator_pdata {
+	const struct regulator_desc *desc;
+	struct st_pwm_voltages *duty_cycle_table;
+};
+
+struct st_pwm_regulator_data {
+	const struct st_pwm_regulator_pdata *pdata;
+	struct pwm_device *pwm;
+	bool enabled;
+	int state;
+};
+
+struct st_pwm_voltages {
+	unsigned int uV;
+	unsigned int dutycycle;
+};
+
+static int st_pwm_regulator_get_voltage_sel(struct regulator_dev *dev)
+{
+	struct st_pwm_regulator_data *drvdata = rdev_get_drvdata(dev);
+
+	return drvdata->state;
+}
+
+static int st_pwm_regulator_set_voltage_sel(struct regulator_dev *dev,
+					    unsigned selector)
+{
+	struct st_pwm_regulator_data *drvdata = rdev_get_drvdata(dev);
+	int dutycycle;
+	int ret;
+
+	dutycycle = (ST_PWM_REG_PERIOD / 100) *
+		drvdata->pdata->duty_cycle_table[selector].dutycycle;
+
+	ret = pwm_config(drvdata->pwm, dutycycle, ST_PWM_REG_PERIOD);
+	if (ret) {
+		dev_err(&dev->dev, "Failed to configure PWM\n");
+		return ret;
+	}
+
+	drvdata->state = selector;
+
+	if (!drvdata->enabled) {
+		ret = pwm_enable(drvdata->pwm);
+		if (ret) {
+			dev_err(&dev->dev, "Failed to enable PWM\n");
+			return ret;
+		}
+		drvdata->enabled = true;
+	}
+
+	return 0;
+}
+
+static int st_pwm_regulator_list_voltage(struct regulator_dev *dev,
+					 unsigned selector)
+{
+	struct st_pwm_regulator_data *drvdata = rdev_get_drvdata(dev);
+
+	if (selector >= dev->desc->n_voltages)
+		return -EINVAL;
+
+	return drvdata->pdata->duty_cycle_table[selector].uV;
+}
+
+static struct regulator_ops st_pwm_regulator_voltage_ops = {
+	.set_voltage_sel = st_pwm_regulator_set_voltage_sel,
+	.get_voltage_sel = st_pwm_regulator_get_voltage_sel,
+	.list_voltage    = st_pwm_regulator_list_voltage,
+	.map_voltage     = regulator_map_voltage_iterate,
+};
+
+static struct st_pwm_voltages b2105_duty_cycle_table[] = {
+	{ .uV = 1114000, .dutycycle = 0,  },
+	{ .uV = 1095000, .dutycycle = 10, },
+	{ .uV = 1076000, .dutycycle = 20, },
+	{ .uV = 1056000, .dutycycle = 30, },
+	{ .uV = 1036000, .dutycycle = 40, },
+	{ .uV = 1016000, .dutycycle = 50, },
+	/* WARNING: Values above 50% duty-cycle cause boot failures. */
+};
+
+static const struct regulator_desc b2105_desc = {
+	.name		= "b2105-pwm-regulator",
+	.ops		= &st_pwm_regulator_voltage_ops,
+	.type		= REGULATOR_VOLTAGE,
+	.owner		= THIS_MODULE,
+	.n_voltages	= ARRAY_SIZE(b2105_duty_cycle_table),
+	.supply_name    = "pwm",
+};
+
+static const struct st_pwm_regulator_pdata b2105_info = {
+	.desc		  = &b2105_desc,
+	.duty_cycle_table = b2105_duty_cycle_table,
+};
+
+static struct of_device_id st_pwm_of_match[] = {
+	{ .compatible = "st,b2105-pwm-regulator", .data = &b2105_info, },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, st_pwm_of_match);
+
+static int st_pwm_regulator_probe(struct platform_device *pdev)
+{
+	struct st_pwm_regulator_data *drvdata;
+	struct regulator_dev *regulator;
+	struct regulator_config config = { };
+	struct device_node *np = pdev->dev.of_node;
+	const struct of_device_id *of_match;
+
+	if (!np) {
+		dev_err(&pdev->dev, "Device Tree node missing\n");
+		return -EINVAL;
+	}
+
+	drvdata = devm_kzalloc(&pdev->dev, sizeof(*drvdata), GFP_KERNEL);
+	if (!drvdata)
+		return -ENOMEM;
+
+	of_match = of_match_device(st_pwm_of_match, &pdev->dev);
+	if (!of_match) {
+		dev_err(&pdev->dev, "failed to match of device\n");
+		return -ENODEV;
+	}
+	drvdata->pdata = of_match->data;
+
+	config.init_data = of_get_regulator_init_data(&pdev->dev, np);
+	if (!config.init_data)
+		return -ENOMEM;
+
+	config.of_node = np;
+	config.dev = &pdev->dev;
+	config.driver_data = drvdata;
+
+	drvdata->pwm = devm_pwm_get(&pdev->dev, NULL);
+	if (IS_ERR(drvdata->pwm)) {
+		dev_err(&pdev->dev, "Failed to get PWM\n");
+		return PTR_ERR(drvdata->pwm);
+	}
+
+	regulator = devm_regulator_register(&pdev->dev,
+					    drvdata->pdata->desc, &config);
+	if (IS_ERR(regulator)) {
+		dev_err(&pdev->dev, "Failed to register regulator %s\n",
+			drvdata->pdata->desc->name);
+		return PTR_ERR(regulator);
+	}
+
+	return 0;
+}
+
+static struct platform_driver st_pwm_regulator_driver = {
+	.driver = {
+		.name		= "st-pwm-regulator",
+		.owner		= THIS_MODULE,
+		.of_match_table = of_match_ptr(st_pwm_of_match),
+	},
+	.probe = st_pwm_regulator_probe,
+};
+
+module_platform_driver(st_pwm_regulator_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Lee Jones <lee.jones@linaro.org>");
+MODULE_DESCRIPTION("ST PWM Regulator Driver");
+MODULE_ALIAS("platform:st_pwm-regulator");

drivers/regulator/ti-abb-regulator.c

@@ -54,8 +54,8 @@ struct ti_abb_info {
 
 /**
  * struct ti_abb_reg - Register description for ABB block
- * @setup_reg:			setup register offset from base
- * @control_reg:		control register offset from base
+ * @setup_off:			setup register offset from base
+ * @control_off:		control register offset from base
  * @sr2_wtcnt_value_mask:	setup register- sr2_wtcnt_value mask
  * @fbb_sel_mask:		setup register- FBB sel mask
  * @rbb_sel_mask:		setup register- RBB sel mask
@@ -64,8 +64,8 @@ struct ti_abb_info {
  * @opp_sel_mask:		control register - mask for mode to operate
  */
 struct ti_abb_reg {
-	u32 setup_reg;
-	u32 control_reg;
+	u32 setup_off;
+	u32 control_off;
 
 	/* Setup register fields */
 	u32 sr2_wtcnt_value_mask;
@@ -83,6 +83,8 @@ struct ti_abb_reg {
  * @rdesc:			regulator descriptor
  * @clk:			clock(usually sysclk) supplying ABB block
  * @base:			base address of ABB block
+ * @setup_reg:			setup register of ABB block
+ * @control_reg:		control register of ABB block
  * @int_base:			interrupt register base address
  * @efuse_base:			(optional) efuse base address for ABB modes
  * @ldo_base:			(optional) LDOVBB vset override base address
@@ -99,6 +101,8 @@ struct ti_abb {
 	struct regulator_desc rdesc;
 	struct clk *clk;
 	void __iomem *base;
+	void __iomem *setup_reg;
+	void __iomem *control_reg;
 	void __iomem *int_base;
 	void __iomem *efuse_base;
 	void __iomem *ldo_base;
@@ -118,20 +122,18 @@ struct ti_abb {
  * ti_abb_rmw() - handy wrapper to set specific register bits
  * @mask:	mask for register field
  * @value:	value shifted to mask location and written
- * @offset:	offset of register
- * @base:	base address
+ * @reg:	register address
  *
  * Return: final register value (may be unused)
  */
-static inline u32 ti_abb_rmw(u32 mask, u32 value, u32 offset,
-			     void __iomem *base)
+static inline u32 ti_abb_rmw(u32 mask, u32 value, void __iomem *reg)
 {
 	u32 val;
 
-	val = readl(base + offset);
+	val = readl(reg);
 	val &= ~mask;
 	val |= (value << __ffs(mask)) & mask;
-	writel(val, base + offset);
+	writel(val, reg);
 
 	return val;
 }
@@ -263,21 +265,19 @@ static int ti_abb_set_opp(struct regulator_dev *rdev, struct ti_abb *abb,
 	if (ret)
 		goto out;
 
-	ti_abb_rmw(regs->fbb_sel_mask | regs->rbb_sel_mask, 0, regs->setup_reg,
-		   abb->base);
+	ti_abb_rmw(regs->fbb_sel_mask | regs->rbb_sel_mask, 0, abb->setup_reg);
 
 	switch (info->opp_sel) {
 	case TI_ABB_SLOW_OPP:
-		ti_abb_rmw(regs->rbb_sel_mask, 1, regs->setup_reg, abb->base);
+		ti_abb_rmw(regs->rbb_sel_mask, 1, abb->setup_reg);
 		break;
 	case TI_ABB_FAST_OPP:
-		ti_abb_rmw(regs->fbb_sel_mask, 1, regs->setup_reg, abb->base);
+		ti_abb_rmw(regs->fbb_sel_mask, 1, abb->setup_reg);
 		break;
 	}
 
 	/* program next state of ABB ldo */
-	ti_abb_rmw(regs->opp_sel_mask, info->opp_sel, regs->control_reg,
-		   abb->base);
+	ti_abb_rmw(regs->opp_sel_mask, info->opp_sel, abb->control_reg);
 
 	/*
 	 * program LDO VBB vset override if needed for !bypass mode
@@ -288,7 +288,7 @@ static int ti_abb_set_opp(struct regulator_dev *rdev, struct ti_abb *abb,
 		ti_abb_program_ldovbb(dev, abb, info);
 
 	/* Initiate ABB ldo change */
-	ti_abb_rmw(regs->opp_change_mask, 1, regs->control_reg, abb->base);
+	ti_abb_rmw(regs->opp_change_mask, 1, abb->control_reg);
 
 	/* Wait for ABB LDO to complete transition to new Bias setting */
 	ret = ti_abb_wait_txdone(dev, abb);
@@ -490,8 +490,7 @@ static int ti_abb_init_timings(struct device *dev, struct ti_abb *abb)
 	dev_dbg(dev, "%s: Clk_rate=%ld, sr2_cnt=0x%08x\n", __func__,
 		clk_get_rate(abb->clk), sr2_wt_cnt_val);
 
-	ti_abb_rmw(regs->sr2_wtcnt_value_mask, sr2_wt_cnt_val, regs->setup_reg,
-		   abb->base);
+	ti_abb_rmw(regs->sr2_wtcnt_value_mask, sr2_wt_cnt_val, abb->setup_reg);
 
 	return 0;
 }
@@ -508,32 +507,24 @@ static int ti_abb_init_table(struct device *dev, struct ti_abb *abb,
 			     struct regulator_init_data *rinit_data)
 {
 	struct ti_abb_info *info;
-	const struct property *prop;
-	const __be32 *abb_info;
 	const u32 num_values = 6;
 	char *pname = "ti,abb_info";
-	u32 num_entries, i;
+	u32 i;
 	unsigned int *volt_table;
-	int min_uV = INT_MAX, max_uV = 0;
+	int num_entries, min_uV = INT_MAX, max_uV = 0;
 	struct regulation_constraints *c = &rinit_data->constraints;
 
-	prop = of_find_property(dev->of_node, pname, NULL);
-	if (!prop) {
-		dev_err(dev, "No '%s' property?\n", pname);
-		return -ENODEV;
-	}
-
-	if (!prop->value) {
-		dev_err(dev, "Empty '%s' property?\n", pname);
-		return -ENODATA;
-	}
-
 	/*
 	 * Each abb_info is a set of n-tuple, where n is num_values, consisting
 	 * of voltage and a set of detection logic for ABB information for that
 	 * voltage to apply.
 	 */
-	num_entries = prop->length / sizeof(u32);
+	num_entries = of_property_count_u32_elems(dev->of_node, pname);
+	if (num_entries < 0) {
+		dev_err(dev, "No '%s' property?\n", pname);
+		return num_entries;
+	}
+
 	if (!num_entries || (num_entries % num_values)) {
 		dev_err(dev, "All '%s' list entries need %d vals\n", pname,
 			num_values);
@@ -542,38 +533,38 @@ static int ti_abb_init_table(struct device *dev, struct ti_abb *abb,
 	num_entries /= num_values;
 
 	info = devm_kzalloc(dev, sizeof(*info) * num_entries, GFP_KERNEL);
-	if (!info) {
-		dev_err(dev, "Can't allocate info table for '%s' property\n",
-			pname);
+	if (!info)
 		return -ENOMEM;
-	}
+
 	abb->info = info;
 
 	volt_table = devm_kzalloc(dev, sizeof(unsigned int) * num_entries,
 				  GFP_KERNEL);
-	if (!volt_table) {
-		dev_err(dev, "Can't allocate voltage table for '%s' property\n",
-			pname);
+	if (!volt_table)
 		return -ENOMEM;
-	}
 
 	abb->rdesc.n_voltages = num_entries;
 	abb->rdesc.volt_table = volt_table;
 	/* We do not know where the OPP voltage is at the moment */
 	abb->current_info_idx = -EINVAL;
 
-	abb_info = prop->value;
 	for (i = 0; i < num_entries; i++, info++, volt_table++) {
 		u32 efuse_offset, rbb_mask, fbb_mask, vset_mask;
 		u32 efuse_val;
 
 		/* NOTE: num_values should equal to entries picked up here */
-		*volt_table = be32_to_cpup(abb_info++);
-		info->opp_sel = be32_to_cpup(abb_info++);
-		efuse_offset = be32_to_cpup(abb_info++);
-		rbb_mask = be32_to_cpup(abb_info++);
-		fbb_mask = be32_to_cpup(abb_info++);
-		vset_mask = be32_to_cpup(abb_info++);
+		of_property_read_u32_index(dev->of_node, pname, i * num_values,
+					   volt_table);
+		of_property_read_u32_index(dev->of_node, pname,
+					   i * num_values + 1, &info->opp_sel);
+		of_property_read_u32_index(dev->of_node, pname,
+					   i * num_values + 2, &efuse_offset);
+		of_property_read_u32_index(dev->of_node, pname,
+					   i * num_values + 3, &rbb_mask);
+		of_property_read_u32_index(dev->of_node, pname,
+					   i * num_values + 4, &fbb_mask);
+		of_property_read_u32_index(dev->of_node, pname,
+					   i * num_values + 5, &vset_mask);
 
 		dev_dbg(dev,
 			"[%d]v=%d ABB=%d ef=0x%x rbb=0x%x fbb=0x%x vset=0x%x\n",
@@ -648,8 +639,8 @@ static struct regulator_ops ti_abb_reg_ops = {
 /* Default ABB block offsets, IF this changes in future, create new one */
 static const struct ti_abb_reg abb_regs_v1 = {
 	/* WARNING: registers are wrongly documented in TRM */
-	.setup_reg		= 0x04,
-	.control_reg		= 0x00,
+	.setup_off		= 0x04,
+	.control_off		= 0x00,
 
 	.sr2_wtcnt_value_mask	= (0xff << 8),
 	.fbb_sel_mask		= (0x01 << 2),
@@ -661,8 +652,8 @@ static const struct ti_abb_reg abb_regs_v1 = {
 };
 
 static const struct ti_abb_reg abb_regs_v2 = {
-	.setup_reg		= 0x00,
-	.control_reg		= 0x04,
+	.setup_off		= 0x00,
+	.control_off		= 0x04,
 
 	.sr2_wtcnt_value_mask	= (0xff << 8),
 	.fbb_sel_mask		= (0x01 << 2),
@@ -673,9 +664,20 @@ static const struct ti_abb_reg abb_regs_v2 = {
 	.opp_sel_mask		= (0x03 << 0),
 };
 
+static const struct ti_abb_reg abb_regs_generic = {
+	.sr2_wtcnt_value_mask	= (0xff << 8),
+	.fbb_sel_mask		= (0x01 << 2),
+	.rbb_sel_mask		= (0x01 << 1),
+	.sr2_en_mask		= (0x01 << 0),
+
+	.opp_change_mask	= (0x01 << 2),
+	.opp_sel_mask		= (0x03 << 0),
+};
+
 static const struct of_device_id ti_abb_of_match[] = {
 	{.compatible = "ti,abb-v1", .data = &abb_regs_v1},
 	{.compatible = "ti,abb-v2", .data = &abb_regs_v2},
+	{.compatible = "ti,abb-v3", .data = &abb_regs_generic},
 	{ },
 };
 
@@ -722,11 +724,29 @@ static int ti_abb_probe(struct platform_device *pdev)
 	abb->regs = match->data;
 
 	/* Map ABB resources */
-	pname = "base-address";
-	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, pname);
-	abb->base = devm_ioremap_resource(dev, res);
-	if (IS_ERR(abb->base))
-		return PTR_ERR(abb->base);
+	if (abb->regs->setup_off || abb->regs->control_off) {
+		pname = "base-address";
+		res = platform_get_resource_byname(pdev, IORESOURCE_MEM, pname);
+		abb->base = devm_ioremap_resource(dev, res);
+		if (IS_ERR(abb->base))
+			return PTR_ERR(abb->base);
+
+		abb->setup_reg = abb->base + abb->regs->setup_off;
+		abb->control_reg = abb->base + abb->regs->control_off;
+
+	} else {
+		pname = "control-address";
+		res = platform_get_resource_byname(pdev, IORESOURCE_MEM, pname);
+		abb->control_reg = devm_ioremap_resource(dev, res);
+		if (IS_ERR(abb->control_reg))
+			return PTR_ERR(abb->control_reg);
+
+		pname = "setup-address";
+		res = platform_get_resource_byname(pdev, IORESOURCE_MEM, pname);
+		abb->setup_reg = devm_ioremap_resource(dev, res);
+		if (IS_ERR(abb->setup_reg))
+			return PTR_ERR(abb->setup_reg);
+	}
 
 	pname = "int-address";
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, pname);
@@ -860,7 +880,7 @@ static int ti_abb_probe(struct platform_device *pdev)
 	platform_set_drvdata(pdev, rdev);
 
 	/* Enable the ldo if not already done by bootloader */
-	ti_abb_rmw(abb->regs->sr2_en_mask, 1, abb->regs->setup_reg, abb->base);
+	ti_abb_rmw(abb->regs->sr2_en_mask, 1, abb->setup_reg);
 
 	return 0;
 }

drivers/regulator/tps51632-regulator.c

@@ -227,10 +227,8 @@ static struct tps51632_regulator_platform_data *
 	struct device_node *np = dev->of_node;
 
 	pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
-	if (!pdata) {
-		dev_err(dev, "Memory alloc failed for platform data\n");
+	if (!pdata)
 		return NULL;
-	}
 
 	pdata->reg_init_data = of_get_regulator_init_data(dev, dev->of_node);
 	if (!pdata->reg_init_data) {
@@ -299,10 +297,8 @@ static int tps51632_probe(struct i2c_client *client,
 	}
 
 	tps = devm_kzalloc(&client->dev, sizeof(*tps), GFP_KERNEL);
-	if (!tps) {
-		dev_err(&client->dev, "Memory allocation failed\n");
+	if (!tps)
 		return -ENOMEM;
-	}
 
 	tps->dev = &client->dev;
 	tps->desc.name = client->name;

drivers/regulator/tps62360-regulator.c

@@ -299,10 +299,8 @@ static struct tps62360_regulator_platform_data *
 	struct device_node *np = dev->of_node;
 
 	pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
-	if (!pdata) {
-		dev_err(dev, "Memory alloc failed for platform data\n");
+	if (!pdata)
 		return NULL;
-	}
 
 	pdata->reg_init_data = of_get_regulator_init_data(dev, dev->of_node);
 	if (!pdata->reg_init_data) {
@@ -377,11 +375,8 @@ static int tps62360_probe(struct i2c_client *client,
 	}
 
 	tps = devm_kzalloc(&client->dev, sizeof(*tps), GFP_KERNEL);
-	if (!tps) {
-		dev_err(&client->dev, "%s(): Memory allocation failed\n",
-						__func__);
+	if (!tps)
 		return -ENOMEM;
-	}
 
 	tps->en_discharge = pdata->en_discharge;
 	tps->en_internal_pulldn = pdata->en_internal_pulldn;

drivers/regulator/tps6507x-regulator.c

@@ -359,7 +359,6 @@ static struct regulator_ops tps6507x_pmic_ops = {
 	.map_voltage = regulator_map_voltage_ascend,
 };
 
-#ifdef CONFIG_OF
 static struct of_regulator_match tps6507x_matches[] = {
 	{ .name = "VDCDC1"},
 	{ .name = "VDCDC2"},
@@ -381,12 +380,10 @@ static struct tps6507x_board *tps6507x_parse_dt_reg_data(
 
 	tps_board = devm_kzalloc(&pdev->dev, sizeof(*tps_board),
 					GFP_KERNEL);
-	if (!tps_board) {
-		dev_err(&pdev->dev, "Failure to alloc pdata for regulators.\n");
+	if (!tps_board)
 		return NULL;
-	}
 
-	regulators = of_find_node_by_name(np, "regulators");
+	regulators = of_get_child_by_name(np, "regulators");
 	if (!regulators) {
 		dev_err(&pdev->dev, "regulator node not found\n");
 		return NULL;
@@ -396,6 +393,7 @@ static struct tps6507x_board *tps6507x_parse_dt_reg_data(
 	matches = tps6507x_matches;
 
 	ret = of_regulator_match(&pdev->dev, regulators, matches, count);
+	of_node_put(regulators);
 	if (ret < 0) {
 		dev_err(&pdev->dev, "Error parsing regulator init data: %d\n",
 			ret);
@@ -406,10 +404,8 @@ static struct tps6507x_board *tps6507x_parse_dt_reg_data(
 
 	reg_data = devm_kzalloc(&pdev->dev, (sizeof(struct regulator_init_data)
 					* TPS6507X_NUM_REGULATOR), GFP_KERNEL);
-	if (!reg_data) {
-		dev_err(&pdev->dev, "Failure to alloc init data for regulators.\n");
+	if (!reg_data)
 		return NULL;
-	}
 
 	tps_board->tps6507x_pmic_init_data = reg_data;
 
@@ -424,15 +420,7 @@ static struct tps6507x_board *tps6507x_parse_dt_reg_data(
 
 	return tps_board;
 }
-#else
-static inline struct tps6507x_board *tps6507x_parse_dt_reg_data(
-			struct platform_device *pdev,
-			struct of_regulator_match **tps6507x_reg_matches)
-{
-	*tps6507x_reg_matches = NULL;
-	return NULL;
-}
-#endif
+
 static int tps6507x_pmic_probe(struct platform_device *pdev)
 {
 	struct tps6507x_dev *tps6507x_dev = dev_get_drvdata(pdev->dev.parent);
@@ -453,9 +441,10 @@ static int tps6507x_pmic_probe(struct platform_device *pdev)
 	 */
 
 	tps_board = dev_get_platdata(tps6507x_dev->dev);
-	if (!tps_board && tps6507x_dev->dev->of_node)
+	if (IS_ENABLED(CONFIG_OF) && !tps_board &&
+		tps6507x_dev->dev->of_node)
 		tps_board = tps6507x_parse_dt_reg_data(pdev,
-						&tps6507x_reg_matches);
+				&tps6507x_reg_matches);
 	if (!tps_board)
 		return -EINVAL;
 
@@ -481,7 +470,7 @@ static int tps6507x_pmic_probe(struct platform_device *pdev)
 		tps->info[i] = info;
 		if (init_data->driver_data) {
 			struct tps6507x_reg_platform_data *data =
-							init_data->driver_data;
+					init_data->driver_data;
 			tps->info[i]->defdcdc_default = data->defdcdc_default;
 		}
 

drivers/regulator/tps65090-regulator.c

@@ -168,17 +168,13 @@ static struct tps65090_platform_data *tps65090_parse_dt_reg_data(
 
 	tps65090_pdata = devm_kzalloc(&pdev->dev, sizeof(*tps65090_pdata),
 				GFP_KERNEL);
-	if (!tps65090_pdata) {
-		dev_err(&pdev->dev, "Memory alloc for tps65090_pdata failed\n");
+	if (!tps65090_pdata)
 		return ERR_PTR(-ENOMEM);
-	}
 
 	reg_pdata = devm_kzalloc(&pdev->dev, TPS65090_REGULATOR_MAX *
 				sizeof(*reg_pdata), GFP_KERNEL);
-	if (!reg_pdata) {
-		dev_err(&pdev->dev, "Memory alloc for reg_pdata failed\n");
+	if (!reg_pdata)
 		return ERR_PTR(-ENOMEM);
-	}
 
 	regulators = of_get_child_by_name(np, "regulators");
 	if (!regulators) {
@@ -188,6 +184,7 @@ static struct tps65090_platform_data *tps65090_parse_dt_reg_data(
 
 	ret = of_regulator_match(&pdev->dev, regulators, tps65090_matches,
 			ARRAY_SIZE(tps65090_matches));
+	of_node_put(regulators);
 	if (ret < 0) {
 		dev_err(&pdev->dev,
 			"Error parsing regulator init data: %d\n", ret);
@@ -252,10 +249,8 @@ static int tps65090_regulator_probe(struct platform_device *pdev)
 
 	pmic = devm_kzalloc(&pdev->dev, TPS65090_REGULATOR_MAX * sizeof(*pmic),
 			GFP_KERNEL);
-	if (!pmic) {
-		dev_err(&pdev->dev, "mem alloc for pmic failed\n");
+	if (!pmic)
 		return -ENOMEM;
-	}
 
 	for (num = 0; num < TPS65090_REGULATOR_MAX; num++) {
 		tps_pdata = tps65090_pdata->reg_pdata[num];

drivers/regulator/tps65217-regulator.c

@@ -187,7 +187,7 @@ static struct tps65217_board *tps65217_parse_dt(struct platform_device *pdev)
 	struct device_node *regs;
 	int i, count;
 
-	regs = of_find_node_by_name(node, "regulators");
+	regs = of_get_child_by_name(node, "regulators");
 	if (!regs)
 		return NULL;
 
@@ -202,7 +202,7 @@ static struct tps65217_board *tps65217_parse_dt(struct platform_device *pdev)
 		return NULL;
 
 	for (i = 0; i < count; i++) {
-		if (!reg_matches[i].init_data || !reg_matches[i].of_node)
+		if (!reg_matches[i].of_node)
 			continue;
 
 		pdata->tps65217_init_data[i] = reg_matches[i].init_data;
@@ -222,7 +222,6 @@ static int tps65217_regulator_probe(struct platform_device *pdev)
 {
 	struct tps65217 *tps = dev_get_drvdata(pdev->dev.parent);
 	struct tps65217_board *pdata = dev_get_platdata(tps->dev);
-	struct regulator_init_data *reg_data;
 	struct regulator_dev *rdev;
 	struct regulator_config config = { };
 	int i;
@@ -243,19 +242,9 @@ static int tps65217_regulator_probe(struct platform_device *pdev)
 	platform_set_drvdata(pdev, tps);
 
 	for (i = 0; i < TPS65217_NUM_REGULATOR; i++) {
-
-		reg_data = pdata->tps65217_init_data[i];
-
-		/*
-		 * Regulator API handles empty constraints but not NULL
-		 * constraints
-		 */
-		if (!reg_data)
-			continue;
-
 		/* Register the regulators */
 		config.dev = tps->dev;
-		config.init_data = reg_data;
+		config.init_data = pdata->tps65217_init_data[i];
 		config.driver_data = tps;
 		config.regmap = tps->regmap;
 		if (tps->dev->of_node)

include/linux/mfd/samsung/core.h

@@ -126,7 +126,8 @@ struct sec_platform_data {
 struct sec_regulator_data {
 	int				id;
 	struct regulator_init_data	*initdata;
-	struct device_node *reg_node;
+	struct device_node		*reg_node;
+	int				ext_control_gpio;
 };
 
 /*

include/linux/mfd/samsung/s5m8767.h

@@ -183,9 +183,16 @@ enum s5m8767_regulators {
 	S5M8767_REG_MAX,
 };
 
+/* LDO_EN/BUCK_EN field in registers */
 #define S5M8767_ENCTRL_SHIFT		6
 #define S5M8767_ENCTRL_MASK		(0x3 << S5M8767_ENCTRL_SHIFT)
 
+/*
+ * LDO_EN/BUCK_EN register value for controlling this Buck or LDO
+ * by GPIO (PWREN, BUCKEN).
+ */
+#define S5M8767_ENCTRL_USE_GPIO		0x1
+
 /*
  * Values for BUCK_RAMP field in DVS_RAMP register, matching raw values
  * in mV/us.