Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (25 commits)
  atmel-mci: add MCI2 register definitions
  atmel-mci: Integrate AT91 specific definition in header file
  tmio_mmc: allow compilation for ASIC3
  mmc_block: do not DMA to stack
  sdhci: Print ADMA status and pointer on debug
  tmio_mmc: fix clock setup
  tmio_mmc: map SD control registers after enabling the MFD cell
  tmio_mmc: correct probe return value for num_resources != 3
  tmio_mmc: don't use set_irq_type
  tmio_mmc: add bus_shift support
  MFD,mmc: tmio_mmc: make HCLK configurable
  mmc_spi: don't use EINVAL for possible transmission errors
  cb710: more cleanup for the DEBUG case.
  sdhci: platform driver for SDHCI
  mxcmmc: remove frequency workaround
  cb710: handle DEBUG define in Makefile
  cb710: add missing parenthesis
  cb710: fix printk format string
  mmc: Driver for CB710/720 memory card reader (MMC part)
  pxamci: add regulator support.
  ...

MAINTAINERS

@@ -2112,6 +2112,15 @@ W:	http://sourceforge.net/projects/lpfcxxxx
 S:	Supported
 F:	drivers/scsi/lpfc/
 
+ENE CB710 FLASH CARD READER DRIVER
+P:	Michał Mirosław
+M:	mirq-linux@rere.qmqm.pl
+L:	linux-kernel@vger.kernel.org
+S:	Maintained
+F:	drivers/misc/cb710/
+F:	drivers/mmc/host/cb710-mmc.*
+F:	include/linux/cb710.h
+
 EPSON 1355 FRAMEBUFFER DRIVER
 P:	Christopher Hoover
 M:	ch@murgatroid.com

drivers/mfd/t7l66xb.c

@@ -108,6 +108,10 @@ static int t7l66xb_mmc_disable(struct platform_device *mmc)
 
 /*--------------------------------------------------------------------------*/
 
+static const struct tmio_mmc_data t7166xb_mmc_data = {
+	.hclk = 24000000,
+};
+
 static const struct resource t7l66xb_mmc_resources[] = {
 	{
 		.start = 0x800,
@@ -149,6 +153,7 @@ static struct mfd_cell t7l66xb_cells[] = {
 		.name = "tmio-mmc",
 		.enable = t7l66xb_mmc_enable,
 		.disable = t7l66xb_mmc_disable,
+		.driver_data = &t7166xb_mmc_data,
 		.num_resources = ARRAY_SIZE(t7l66xb_mmc_resources),
 		.resources = t7l66xb_mmc_resources,
 	},

drivers/mfd/tc6387xb.c

@@ -75,6 +75,10 @@ static int tc6387xb_mmc_disable(struct platform_device *mmc)
 
 /*--------------------------------------------------------------------------*/
 
+const static struct tmio_mmc_data tc6387xb_mmc_data = {
+	.hclk = 24000000,
+};
+
 static struct resource tc6387xb_mmc_resources[] = {
 	{
 		.start = 0x800,
@@ -98,6 +102,7 @@ static struct mfd_cell tc6387xb_cells[] = {
 		.name = "tmio-mmc",
 		.enable = tc6387xb_mmc_enable,
 		.disable = tc6387xb_mmc_disable,
+		.driver_data = &tc6387xb_mmc_data,
 		.num_resources = ARRAY_SIZE(tc6387xb_mmc_resources),
 		.resources = tc6387xb_mmc_resources,
 	},

drivers/mfd/tc6393xb.c

@@ -136,6 +136,10 @@ static int tc6393xb_nand_enable(struct platform_device *nand)
 	return 0;
 }
 
+const static struct tmio_mmc_data tc6393xb_mmc_data = {
+	.hclk = 24000000,
+};
+
 static struct resource __devinitdata tc6393xb_nand_resources[] = {
 	{
 		.start	= 0x1000,
@@ -351,6 +355,7 @@ static struct mfd_cell __devinitdata tc6393xb_cells[] = {
 	},
 	[TC6393XB_CELL_MMC] = {
 		.name = "tmio-mmc",
+		.driver_data = &tc6393xb_mmc_data,
 		.num_resources = ARRAY_SIZE(tc6393xb_mmc_resources),
 		.resources = tc6393xb_mmc_resources,
 	},

drivers/misc/Kconfig

@@ -235,5 +235,6 @@ config ISL29003
 
 source "drivers/misc/c2port/Kconfig"
 source "drivers/misc/eeprom/Kconfig"
+source "drivers/misc/cb710/Kconfig"
 
 endif # MISC_DEVICES

drivers/misc/Makefile

@@ -21,3 +21,4 @@ obj-$(CONFIG_HP_ILO)		+= hpilo.o
 obj-$(CONFIG_ISL29003)		+= isl29003.o
 obj-$(CONFIG_C2PORT)		+= c2port/
 obj-y				+= eeprom/
+obj-y				+= cb710/

drivers/misc/cb710/Kconfig

+config CB710_CORE
+	tristate "ENE CB710/720 Flash memory card reader support"
+	depends on PCI
+	help
+	  This option enables support for PCI ENE CB710/720 Flash memory card
+	  reader found in some laptops (ie. some versions of HP Compaq nx9500).
+
+	  You will also have to select some flash card format drivers (MMC/SD,
+	  MemoryStick).
+
+	  This driver can also be built as a module. If so, the module
+	  will be called cb710.
+
+config CB710_DEBUG
+	bool "Enable driver debugging"
+	depends on CB710_CORE != n
+	default n
+	help
+	  This is an option for use by developers; most people should
+	  say N here.  This adds a lot of debugging output to dmesg.
+
+config CB710_DEBUG_ASSUMPTIONS
+	bool
+	depends on CB710_CORE != n
+	default y

drivers/misc/cb710/Makefile

+ifeq ($(CONFIG_CB710_DEBUG),y)
+	EXTRA_CFLAGS		+= -DDEBUG
+endif
+
+obj-$(CONFIG_CB710_CORE)	+= cb710.o
+
+cb710-y				:= core.o sgbuf2.o
+cb710-$(CONFIG_CB710_DEBUG)	+= debug.o

drivers/misc/cb710/core.c

+/*
+ *  cb710/core.c
+ *
+ *  Copyright by Michał Mirosław, 2008-2009
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/pci.h>
+#include <linux/spinlock.h>
+#include <linux/idr.h>
+#include <linux/cb710.h>
+
+static DEFINE_IDA(cb710_ida);
+static DEFINE_SPINLOCK(cb710_ida_lock);
+
+void cb710_pci_update_config_reg(struct pci_dev *pdev,
+	int reg, uint32_t mask, uint32_t xor)
+{
+	u32 rval;
+
+	pci_read_config_dword(pdev, reg, &rval);
+	rval = (rval & mask) ^ xor;
+	pci_write_config_dword(pdev, reg, rval);
+}
+EXPORT_SYMBOL_GPL(cb710_pci_update_config_reg);
+
+/* Some magic writes based on Windows driver init code */
+static int __devinit cb710_pci_configure(struct pci_dev *pdev)
+{
+	unsigned int devfn = PCI_DEVFN(PCI_SLOT(pdev->devfn), 0);
+	struct pci_dev *pdev0 = pci_get_slot(pdev->bus, devfn);
+	u32 val;
+
+	cb710_pci_update_config_reg(pdev, 0x48,
+		~0x000000FF, 0x0000003F);
+
+	pci_read_config_dword(pdev, 0x48, &val);
+	if (val & 0x80000000)
+		return 0;
+
+	if (!pdev0)
+		return -ENODEV;
+
+	if (pdev0->vendor == PCI_VENDOR_ID_ENE
+	    && pdev0->device == PCI_DEVICE_ID_ENE_720) {
+		cb710_pci_update_config_reg(pdev0, 0x8C,
+			~0x00F00000, 0x00100000);
+		cb710_pci_update_config_reg(pdev0, 0xB0,
+			~0x08000000, 0x08000000);
+	}
+
+	cb710_pci_update_config_reg(pdev0, 0x8C,
+		~0x00000F00, 0x00000200);
+	cb710_pci_update_config_reg(pdev0, 0x90,
+		~0x00060000, 0x00040000);
+
+	pci_dev_put(pdev0);
+
+	return 0;
+}
+
+static irqreturn_t cb710_irq_handler(int irq, void *data)
+{
+	struct cb710_chip *chip = data;
+	struct cb710_slot *slot = &chip->slot[0];
+	irqreturn_t handled = IRQ_NONE;
+	unsigned nr;
+
+	spin_lock(&chip->irq_lock); /* incl. smp_rmb() */
+
+	for (nr = chip->slots; nr; ++slot, --nr) {
+		cb710_irq_handler_t handler_func = slot->irq_handler;
+		if (handler_func && handler_func(slot))
+			handled = IRQ_HANDLED;
+	}
+
+	spin_unlock(&chip->irq_lock);
+
+	return handled;
+}
+
+static void cb710_release_slot(struct device *dev)
+{
+#ifdef CONFIG_CB710_DEBUG_ASSUMPTIONS
+	struct cb710_slot *slot = cb710_pdev_to_slot(to_platform_device(dev));
+	struct cb710_chip *chip = cb710_slot_to_chip(slot);
+
+	/* slot struct can be freed now */
+	atomic_dec(&chip->slot_refs_count);
+#endif
+}
+
+static int __devinit cb710_register_slot(struct cb710_chip *chip,
+	unsigned slot_mask, unsigned io_offset, const char *name)
+{
+	int nr = chip->slots;
+	struct cb710_slot *slot = &chip->slot[nr];
+	int err;
+
+	dev_dbg(cb710_chip_dev(chip),
+		"register: %s.%d; slot %d; mask %d; IO offset: 0x%02X\n",
+		name, chip->platform_id, nr, slot_mask, io_offset);
+
+	/* slot->irq_handler == NULL here; this needs to be
+	 * seen before platform_device_register() */
+	++chip->slots;
+	smp_wmb();
+
+	slot->iobase = chip->iobase + io_offset;
+	slot->pdev.name = name;
+	slot->pdev.id = chip->platform_id;
+	slot->pdev.dev.parent = &chip->pdev->dev;
+	slot->pdev.dev.release = cb710_release_slot;
+
+	err = platform_device_register(&slot->pdev);
+
+#ifdef CONFIG_CB710_DEBUG_ASSUMPTIONS
+	atomic_inc(&chip->slot_refs_count);
+#endif
+
+	if (err) {
+		/* device_initialize() called from platform_device_register()
+		 * wants this on error path */
+		platform_device_put(&slot->pdev);
+
+		/* slot->irq_handler == NULL here anyway, so no lock needed */
+		--chip->slots;
+		return err;
+	}
+
+	chip->slot_mask |= slot_mask;
+
+	return 0;
+}
+
+static void cb710_unregister_slot(struct cb710_chip *chip,
+	unsigned slot_mask)
+{
+	int nr = chip->slots - 1;
+
+	if (!(chip->slot_mask & slot_mask))
+		return;
+
+	platform_device_unregister(&chip->slot[nr].pdev);
+
+	/* complementary to spin_unlock() in cb710_set_irq_handler() */
+	smp_rmb();
+	BUG_ON(chip->slot[nr].irq_handler != NULL);
+
+	/* slot->irq_handler == NULL here, so no lock needed */
+	--chip->slots;
+	chip->slot_mask &= ~slot_mask;
+}
+
+void cb710_set_irq_handler(struct cb710_slot *slot,
+	cb710_irq_handler_t handler)
+{
+	struct cb710_chip *chip = cb710_slot_to_chip(slot);
+	unsigned long flags;
+
+	spin_lock_irqsave(&chip->irq_lock, flags);
+	slot->irq_handler = handler;
+	spin_unlock_irqrestore(&chip->irq_lock, flags);
+}
+EXPORT_SYMBOL_GPL(cb710_set_irq_handler);
+
+#ifdef CONFIG_PM
+
+static int cb710_suspend(struct pci_dev *pdev, pm_message_t state)
+{
+	struct cb710_chip *chip = pci_get_drvdata(pdev);
+
+	free_irq(pdev->irq, chip);
+	pci_save_state(pdev);
+	pci_disable_device(pdev);
+	if (state.event & PM_EVENT_SLEEP)
+		pci_set_power_state(pdev, PCI_D3cold);
+	return 0;
+}
+
+static int cb710_resume(struct pci_dev *pdev)
+{
+	struct cb710_chip *chip = pci_get_drvdata(pdev);
+	int err;
+
+	pci_set_power_state(pdev, PCI_D0);
+	pci_restore_state(pdev);
+	err = pcim_enable_device(pdev);
+	if (err)
+		return err;
+
+	return devm_request_irq(&pdev->dev, pdev->irq,
+		cb710_irq_handler, IRQF_SHARED, KBUILD_MODNAME, chip);
+}
+
+#endif /* CONFIG_PM */
+
+static int __devinit cb710_probe(struct pci_dev *pdev,
+	const struct pci_device_id *ent)
+{
+	struct cb710_chip *chip;
+	unsigned long flags;
+	u32 val;
+	int err;
+	int n = 0;
+
+	err = cb710_pci_configure(pdev);
+	if (err)
+		return err;
+
+	/* this is actually magic... */
+	pci_read_config_dword(pdev, 0x48, &val);
+	if (!(val & 0x80000000)) {
+		pci_write_config_dword(pdev, 0x48, val|0x71000000);
+		pci_read_config_dword(pdev, 0x48, &val);
+	}
+
+	dev_dbg(&pdev->dev, "PCI config[0x48] = 0x%08X\n", val);
+	if (!(val & 0x70000000))
+		return -ENODEV;
+	val = (val >> 28) & 7;
+	if (val & CB710_SLOT_MMC)
+		++n;
+	if (val & CB710_SLOT_MS)
+		++n;
+	if (val & CB710_SLOT_SM)
+		++n;
+
+	chip = devm_kzalloc(&pdev->dev,
+		sizeof(*chip) + n * sizeof(*chip->slot), GFP_KERNEL);
+	if (!chip)
+		return -ENOMEM;
+
+	err = pcim_enable_device(pdev);
+	if (err)
+		return err;
+
+	err = pcim_iomap_regions(pdev, 0x0001, KBUILD_MODNAME);
+	if (err)
+		return err;
+
+	chip->pdev = pdev;
+	chip->iobase = pcim_iomap_table(pdev)[0];
+
+	pci_set_drvdata(pdev, chip);
+
+	err = devm_request_irq(&pdev->dev, pdev->irq,
+		cb710_irq_handler, IRQF_SHARED, KBUILD_MODNAME, chip);
+	if (err)
+		return err;
+
+	do {
+		if (!ida_pre_get(&cb710_ida, GFP_KERNEL))
+			return -ENOMEM;
+
+		spin_lock_irqsave(&cb710_ida_lock, flags);
+		err = ida_get_new(&cb710_ida, &chip->platform_id);
+		spin_unlock_irqrestore(&cb710_ida_lock, flags);
+
+		if (err && err != -EAGAIN)
+			return err;
+	} while (err);
+
+
+	dev_info(&pdev->dev, "id %d, IO 0x%p, IRQ %d\n",
+		chip->platform_id, chip->iobase, pdev->irq);
+
+	if (val & CB710_SLOT_MMC) {	/* MMC/SD slot */
+		err = cb710_register_slot(chip,
+			CB710_SLOT_MMC, 0x00, "cb710-mmc");
+		if (err)
+			return err;
+	}
+
+	if (val & CB710_SLOT_MS) {	/* MemoryStick slot */
+		err = cb710_register_slot(chip,
+			CB710_SLOT_MS, 0x40, "cb710-ms");
+		if (err)
+			goto unreg_mmc;
+	}
+
+	if (val & CB710_SLOT_SM) {	/* SmartMedia slot */
+		err = cb710_register_slot(chip,
+			CB710_SLOT_SM, 0x60, "cb710-sm");
+		if (err)
+			goto unreg_ms;
+	}
+
+	return 0;
+unreg_ms:
+	cb710_unregister_slot(chip, CB710_SLOT_MS);
+unreg_mmc:
+	cb710_unregister_slot(chip, CB710_SLOT_MMC);
+
+#ifdef CONFIG_CB710_DEBUG_ASSUMPTIONS
+	BUG_ON(atomic_read(&chip->slot_refs_count) != 0);
+#endif
+	return err;
+}
+
+static void __devexit cb710_remove_one(struct pci_dev *pdev)
+{
+	struct cb710_chip *chip = pci_get_drvdata(pdev);
+	unsigned long flags;
+
+	cb710_unregister_slot(chip, CB710_SLOT_SM);
+	cb710_unregister_slot(chip, CB710_SLOT_MS);
+	cb710_unregister_slot(chip, CB710_SLOT_MMC);
+#ifdef CONFIG_CB710_DEBUG_ASSUMPTIONS
+	BUG_ON(atomic_read(&chip->slot_refs_count) != 0);
+#endif
+
+	spin_lock_irqsave(&cb710_ida_lock, flags);
+	ida_remove(&cb710_ida, chip->platform_id);
+	spin_unlock_irqrestore(&cb710_ida_lock, flags);
+}
+
+static const struct pci_device_id cb710_pci_tbl[] = {
+	{ PCI_VENDOR_ID_ENE, PCI_DEVICE_ID_ENE_CB710_FLASH,
+		PCI_ANY_ID, PCI_ANY_ID, },
+	{ 0, }
+};
+
+static struct pci_driver cb710_driver = {
+	.name = KBUILD_MODNAME,
+	.id_table = cb710_pci_tbl,
+	.probe = cb710_probe,
+	.remove = __devexit_p(cb710_remove_one),
+#ifdef CONFIG_PM
+	.suspend = cb710_suspend,
+	.resume = cb710_resume,
+#endif
+};
+
+static int __init cb710_init_module(void)
+{
+	return pci_register_driver(&cb710_driver);
+}
+
+static void __exit cb710_cleanup_module(void)
+{
+	pci_unregister_driver(&cb710_driver);
+	ida_destroy(&cb710_ida);
+}
+
+module_init(cb710_init_module);
+module_exit(cb710_cleanup_module);
+
+MODULE_AUTHOR("Michał Mirosław <mirq-linux@rere.qmqm.pl>");
+MODULE_DESCRIPTION("ENE CB710 memory card reader driver");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, cb710_pci_tbl);

drivers/misc/cb710/debug.c

+/*
+ *  cb710/debug.c
+ *
+ *  Copyright by Michał Mirosław, 2008-2009
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/cb710.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+
+#define CB710_REG_COUNT		0x80
+
+static const u16 allow[CB710_REG_COUNT/16] = {
+	0xFFF0, 0xFFFF, 0xFFFF, 0xFFFF,
+	0xFFF0, 0xFFFF, 0xFFFF, 0xFFFF,
+};
+static const char *const prefix[ARRAY_SIZE(allow)] = {
+	"MMC", "MMC", "MMC", "MMC",
+	"MS?", "MS?", "SM?", "SM?"
+};
+
+static inline int allow_reg_read(unsigned block, unsigned offset, unsigned bits)
+{
+	unsigned mask = (1 << bits/8) - 1;
+	offset *= bits/8;
+	return ((allow[block] >> offset) & mask) == mask;
+}
+
+#define CB710_READ_REGS_TEMPLATE(t)					\
+static void cb710_read_regs_##t(void __iomem *iobase,			\
+	u##t *reg, unsigned select)					\
+{									\
+	unsigned i, j;							\
+									\
+	for (i = 0; i < ARRAY_SIZE(allow); ++i, reg += 16/(t/8)) {	\
+		if (!(select & (1 << i)))					\
+			continue;					\
+									\
+		for (j = 0; j < 0x10/(t/8); ++j) {			\
+			if (!allow_reg_read(i, j, t))			\
+				continue;				\
+			reg[j] = ioread##t(iobase			\
+				+ (i << 4) + (j * (t/8)));		\
+		}							\
+	}								\
+}
+
+static const char cb710_regf_8[] = "%02X";
+static const char cb710_regf_16[] = "%04X";
+static const char cb710_regf_32[] = "%08X";
+static const char cb710_xes[] = "xxxxxxxx";
+
+#define CB710_DUMP_REGS_TEMPLATE(t)					\
+static void cb710_dump_regs_##t(struct device *dev,			\
+	const u##t *reg, unsigned select)				\
+{									\
+	const char *const xp = &cb710_xes[8 - t/4];			\
+	const char *const format = cb710_regf_##t;			\
+									\
+	char msg[100], *p;						\
+	unsigned i, j;							\
+									\
+	for (i = 0; i < ARRAY_SIZE(allow); ++i, reg += 16/(t/8)) {	\
+		if (!(select & (1 << i)))				\
+			continue;					\
+		p = msg;						\
+		for (j = 0; j < 0x10/(t/8); ++j) {			\
+			*p++ = ' ';					\
+			if (j == 8/(t/8))				\
+				*p++ = ' ';				\
+			if (allow_reg_read(i, j, t))			\
+				p += sprintf(p, format, reg[j]);	\
+			else						\
+				p += sprintf(p, "%s", xp);		\
+		}							\
+		dev_dbg(dev, "%s 0x%02X %s\n", prefix[i], i << 4, msg);	\
+	}								\
+}
+
+#define CB710_READ_AND_DUMP_REGS_TEMPLATE(t)				\
+static void cb710_read_and_dump_regs_##t(struct cb710_chip *chip,	\
+	unsigned select)						\
+{									\
+	u##t regs[CB710_REG_COUNT/sizeof(u##t)];			\
+									\
+	memset(&regs, 0, sizeof(regs));					\
+	cb710_read_regs_##t(chip->iobase, regs, select);		\
+	cb710_dump_regs_##t(cb710_chip_dev(chip), regs, select);	\
+}
+
+#define CB710_REG_ACCESS_TEMPLATES(t)		\
+  CB710_READ_REGS_TEMPLATE(t)			\
+  CB710_DUMP_REGS_TEMPLATE(t)			\
+  CB710_READ_AND_DUMP_REGS_TEMPLATE(t)
+
+CB710_REG_ACCESS_TEMPLATES(8)
+CB710_REG_ACCESS_TEMPLATES(16)
+CB710_REG_ACCESS_TEMPLATES(32)
+
+void cb710_dump_regs(struct cb710_chip *chip, unsigned select)
+{
+	if (!(select & CB710_DUMP_REGS_MASK))
+		select = CB710_DUMP_REGS_ALL;
+	if (!(select & CB710_DUMP_ACCESS_MASK))
+		select |= CB710_DUMP_ACCESS_8;
+
+	if (select & CB710_DUMP_ACCESS_32)
+		cb710_read_and_dump_regs_32(chip, select);
+	if (select & CB710_DUMP_ACCESS_16)
+		cb710_read_and_dump_regs_16(chip, select);
+	if (select & CB710_DUMP_ACCESS_8)
+		cb710_read_and_dump_regs_8(chip, select);
+}
+EXPORT_SYMBOL_GPL(cb710_dump_regs);
+

drivers/misc/cb710/sgbuf2.c

+/*
+ *  cb710/sgbuf2.c
+ *
+ *  Copyright by Michał Mirosław, 2008-2009
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/cb710.h>
+
+static bool sg_dwiter_next(struct sg_mapping_iter *miter)
+{
+	if (sg_miter_next(miter)) {
+		miter->consumed = 0;
+		return true;
+	} else
+		return false;
+}
+
+static bool sg_dwiter_is_at_end(struct sg_mapping_iter *miter)
+{
+	return miter->length == miter->consumed && !sg_dwiter_next(miter);
+}
+
+static uint32_t sg_dwiter_read_buffer(struct sg_mapping_iter *miter)
+{
+	size_t len, left = 4;
+	uint32_t data;
+	void *addr = &data;
+
+	do {
+		len = min(miter->length - miter->consumed, left);
+		memcpy(addr, miter->addr + miter->consumed, len);
+		miter->consumed += len;
+		left -= len;
+		if (!left)
+			return data;
+		addr += len;
+	} while (sg_dwiter_next(miter));
+
+	memset(addr, 0, left);
+	return data;
+}
+
+static inline bool needs_unaligned_copy(const void *ptr)
+{
+#ifdef HAVE_EFFICIENT_UNALIGNED_ACCESS
+	return false;
+#else
+	return ((ptr - NULL) & 3) != 0;
+#endif
+}
+
+static bool sg_dwiter_get_next_block(struct sg_mapping_iter *miter, uint32_t **ptr)
+{
+	size_t len;
+
+	if (sg_dwiter_is_at_end(miter))
+		return true;
+
+	len = miter->length - miter->consumed;
+
+	if (likely(len >= 4 && !needs_unaligned_copy(
+			miter->addr + miter->consumed))) {
+		*ptr = miter->addr + miter->consumed;
+		miter->consumed += 4;
+		return true;
+	}
+
+	return false;
+}
+
+/**
+ * cb710_sg_dwiter_read_next_block() - get next 32-bit word from sg buffer
+ * @miter: sg mapping iterator used for reading
+ *
+ * Description:
+ *   Returns 32-bit word starting at byte pointed to by @miter@
+ *   handling any alignment issues.  Bytes past the buffer's end
+ *   are not accessed (read) but are returned as zeroes.  @miter@
+ *   is advanced by 4 bytes or to the end of buffer whichever is
+ *   closer.
+ *
+ * Context:
+ *   Same requirements as in sg_miter_next().
+ *
+ * Returns:
+ *   32-bit word just read.
+ */
+uint32_t cb710_sg_dwiter_read_next_block(struct sg_mapping_iter *miter)
+{
+	uint32_t *ptr = NULL;
+
+	if (likely(sg_dwiter_get_next_block(miter, &ptr)))
+		return ptr ? *ptr : 0;
+
+	return sg_dwiter_read_buffer(miter);
+}
+EXPORT_SYMBOL_GPL(cb710_sg_dwiter_read_next_block);
+
+static void sg_dwiter_write_slow(struct sg_mapping_iter *miter, uint32_t data)
+{
+	size_t len, left = 4;
+	void *addr = &data;
+
+	do {
+		len = min(miter->length - miter->consumed, left);
+		memcpy(miter->addr, addr, len);
+		miter->consumed += len;
+		left -= len;
+		if (!left)
+			return;
+		addr += len;
+		flush_kernel_dcache_page(miter->page);
+	} while (sg_dwiter_next(miter));
+}
+
+/**
+ * cb710_sg_dwiter_write_next_block() - write next 32-bit word to sg buffer
+ * @miter: sg mapping iterator used for writing
+ *
+ * Description:
+ *   Writes 32-bit word starting at byte pointed to by @miter@
+ *   handling any alignment issues.  Bytes which would be written
+ *   past the buffer's end are silently discarded. @miter@ is
+ *   advanced by 4 bytes or to the end of buffer whichever is closer.
+ *
+ * Context:
+ *   Same requirements as in sg_miter_next().
+ */
+void cb710_sg_dwiter_write_next_block(struct sg_mapping_iter *miter, uint32_t data)
+{
+	uint32_t *ptr = NULL;
+
+	if (likely(sg_dwiter_get_next_block(miter, &ptr))) {
+		if (ptr)
+			*ptr = data;
+		else
+			return;
+	} else
+		sg_dwiter_write_slow(miter, data);
+
+	if (miter->length == miter->consumed)
+		flush_kernel_dcache_page(miter->page);
+}
+EXPORT_SYMBOL_GPL(cb710_sg_dwiter_write_next_block);
+

drivers/mmc/card/block.c

@@ -147,7 +147,8 @@ struct mmc_blk_request {
 static u32 mmc_sd_num_wr_blocks(struct mmc_card *card)
 {
 	int err;
-	__be32 blocks;
+	u32 result;
+	__be32 *blocks;
 
 	struct mmc_request mrq;
 	struct mmc_command cmd;
@@ -199,14 +200,21 @@ static u32 mmc_sd_num_wr_blocks(struct mmc_card *card)
 	mrq.cmd = &cmd;
 	mrq.data = &data;
 
-	sg_init_one(&sg, &blocks, 4);
+	blocks = kmalloc(4, GFP_KERNEL);
+	if (!blocks)
+		return (u32)-1;
+
+	sg_init_one(&sg, blocks, 4);
 
 	mmc_wait_for_req(card->host, &mrq);
 
+	result = ntohl(*blocks);
+	kfree(blocks);
+
 	if (cmd.error || data.error)
-		return (u32)-1;
+		result = (u32)-1;
 
-	return ntohl(blocks);
+	return result;
 }
 
 static u32 get_card_status(struct mmc_card *card, struct request *req)

drivers/mmc/core/core.c

@@ -708,7 +708,13 @@ static void mmc_power_up(struct mmc_host *host)
 	 */
 	mmc_delay(10);
 
-	host->ios.clock = host->f_min;
+	if (host->f_min > 400000) {
+		pr_warning("%s: Minimum clock frequency too high for "
+				"identification mode\n", mmc_hostname(host));
+		host->ios.clock = host->f_min;
+	} else
+		host->ios.clock = 400000;
+
 	host->ios.power_mode = MMC_POWER_ON;
 	mmc_set_ios(host);
 
@@ -855,61 +861,72 @@ void mmc_rescan(struct work_struct *work)
 
 	mmc_bus_get(host);
 
-	if (host->bus_ops == NULL) {
-		/*
-		 * Only we can add a new handler, so it's safe to
-		 * release the lock here.
-		 */
+	/* if there is a card registered, check whether it is still present */
+	if ((host->bus_ops != NULL) && host->bus_ops->detect && !host->bus_dead)
+		host->bus_ops->detect(host);
+
+	mmc_bus_put(host);
+
+
+	mmc_bus_get(host);
+
+	/* if there still is a card present, stop here */
+	if (host->bus_ops != NULL) {
 		mmc_bus_put(host);
+		goto out;
+	}
 
-		if (host->ops->get_cd && host->ops->get_cd(host) == 0)
-			goto out;
+	/* detect a newly inserted card */
 
-		mmc_claim_host(host);
+	/*
+	 * Only we can add a new handler, so it's safe to
+	 * release the lock here.
+	 */
+	mmc_bus_put(host);
 
-		mmc_power_up(host);
-		mmc_go_idle(host);
+	if (host->ops->get_cd && host->ops->get_cd(host) == 0)
+		goto out;
 
-		mmc_send_if_cond(host, host->ocr_avail);
+	mmc_claim_host(host);
 
-		/*
-		 * First we search for SDIO...
-		 */
-		err = mmc_send_io_op_cond(host, 0, &ocr);
-		if (!err) {
-			if (mmc_attach_sdio(host, ocr))
-				mmc_power_off(host);
-			goto out;
-		}
+	mmc_power_up(host);
+	mmc_go_idle(host);
 
-		/*
-		 * ...then normal SD...
-		 */
-		err = mmc_send_app_op_cond(host, 0, &ocr);
-		if (!err) {
-			if (mmc_attach_sd(host, ocr))
-				mmc_power_off(host);
-			goto out;
-		}
+	mmc_send_if_cond(host, host->ocr_avail);
 
-		/*
-		 * ...and finally MMC.
-		 */
-		err = mmc_send_op_cond(host, 0, &ocr);
-		if (!err) {
-			if (mmc_attach_mmc(host, ocr))
-				mmc_power_off(host);
-			goto out;
-		}
+	/*
+	 * First we search for SDIO...
+	 */
+	err = mmc_send_io_op_cond(host, 0, &ocr);
+	if (!err) {
+		if (mmc_attach_sdio(host, ocr))
+			mmc_power_off(host);
+		goto out;
+	}
 
-		mmc_release_host(host);
-		mmc_power_off(host);
-	} else {
-		if (host->bus_ops->detect && !host->bus_dead)
-			host->bus_ops->detect(host);
+	/*
+	 * ...then normal SD...
+	 */
+	err = mmc_send_app_op_cond(host, 0, &ocr);
+	if (!err) {
+		if (mmc_attach_sd(host, ocr))
+			mmc_power_off(host);
+		goto out;
+	}
 
-		mmc_bus_put(host);
+	/*
+	 * ...and finally MMC.
+	 */
+	err = mmc_send_op_cond(host, 0, &ocr);
+	if (!err) {
+		if (mmc_attach_mmc(host, ocr))
+			mmc_power_off(host);
+		goto out;
 	}
+
+	mmc_release_host(host);
+	mmc_power_off(host);
+
 out:
 	if (host->caps & MMC_CAP_NEEDS_POLL)
 		mmc_schedule_delayed_work(&host->detect, HZ);

drivers/mmc/host/Kconfig

@@ -83,6 +83,17 @@ config MMC_SDHCI_OF
 
 	  If unsure, say N.
 
+config MMC_SDHCI_PLTFM
+	tristate "SDHCI support on the platform specific bus"
+	depends on MMC_SDHCI
+	help
+	  This selects the platform specific bus support for Secure Digital Host
+	  Controller Interface.
+
+	  If you have a controller with this interface, say Y or M here.
+
+	  If unsure, say N.
+
 config MMC_OMAP
 	tristate "TI OMAP Multimedia Card Interface support"
 	depends on ARCH_OMAP
@@ -237,7 +248,20 @@ config MMC_SDRICOH_CS
 
 config MMC_TMIO
 	tristate "Toshiba Mobile IO Controller (TMIO) MMC/SD function support"
-	depends on MFD_TMIO
+	depends on MFD_TMIO || MFD_ASIC3
 	help
 	  This provides support for the SD/MMC cell found in TC6393XB,
-	  T7L66XB and also ipaq ASIC3
+	  T7L66XB and also HTC ASIC3
+
+config MMC_CB710
+	tristate "ENE CB710 MMC/SD Interface support"
+	depends on PCI
+	select CB710_CORE
+	help
+	  This option enables support for MMC/SD part of ENE CB710/720 Flash
+	  memory card reader found in some laptops (ie. some versions of
+	  HP Compaq nx9500).
+
+	  This driver can also be built as a module. If so, the module
+	  will be called cb710-mmc.
+

drivers/mmc/host/Makefile

@@ -14,6 +14,7 @@ obj-$(CONFIG_MMC_SDHCI)		+= sdhci.o
 obj-$(CONFIG_MMC_SDHCI_PCI)	+= sdhci-pci.o
 obj-$(CONFIG_MMC_RICOH_MMC)	+= ricoh_mmc.o
 obj-$(CONFIG_MMC_SDHCI_OF)	+= sdhci-of.o
+obj-$(CONFIG_MMC_SDHCI_PLTFM)	+= sdhci-pltfm.o
 obj-$(CONFIG_MMC_WBSD)		+= wbsd.o
 obj-$(CONFIG_MMC_AU1X)		+= au1xmmc.o
 obj-$(CONFIG_MMC_OMAP)		+= omap.o
@@ -29,4 +30,8 @@ endif
 obj-$(CONFIG_MMC_S3C)   	+= s3cmci.o
 obj-$(CONFIG_MMC_SDRICOH_CS)	+= sdricoh_cs.o
 obj-$(CONFIG_MMC_TMIO)		+= tmio_mmc.o
+obj-$(CONFIG_MMC_CB710)	+= cb710-mmc.o
 
+ifeq ($(CONFIG_CB710_DEBUG),y)
+	CFLAGS-cb710-mmc	+= -DDEBUG
+endif

drivers/mmc/host/atmel-mci-regs.h

@@ -7,6 +7,12 @@
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
+
+/*
+ * Superset of MCI IP registers integrated in Atmel AVR32 and AT91 Processors
+ * Registers and bitfields marked with [2] are only available in MCI2
+ */
+
 #ifndef __DRIVERS_MMC_ATMEL_MCI_H__
 #define __DRIVERS_MMC_ATMEL_MCI_H__
 
@@ -14,11 +20,17 @@
 #define MCI_CR			0x0000	/* Control */
 # define MCI_CR_MCIEN		(  1 <<  0)	/* MCI Enable */
 # define MCI_CR_MCIDIS		(  1 <<  1)	/* MCI Disable */
+# define MCI_CR_PWSEN		(  1 <<  2)	/* Power Save Enable */
+# define MCI_CR_PWSDIS		(  1 <<  3)	/* Power Save Disable */
 # define MCI_CR_SWRST		(  1 <<  7)	/* Software Reset */
 #define MCI_MR			0x0004	/* Mode */
 # define MCI_MR_CLKDIV(x)	((x) <<  0)	/* Clock Divider */
+# define MCI_MR_PWSDIV(x)	((x) <<  8)	/* Power Saving Divider */
 # define MCI_MR_RDPROOF		(  1 << 11)	/* Read Proof */
 # define MCI_MR_WRPROOF		(  1 << 12)	/* Write Proof */
+# define MCI_MR_PDCFBYTE	(  1 << 13)	/* Force Byte Transfer */
+# define MCI_MR_PDCPADV		(  1 << 14)	/* Padding Value */
+# define MCI_MR_PDCMODE		(  1 << 15)	/* PDC-oriented Mode */
 #define MCI_DTOR		0x0008	/* Data Timeout */
 # define MCI_DTOCYC(x)		((x) <<  0)	/* Data Timeout Cycles */
 # define MCI_DTOMUL(x)		((x) <<  4)	/* Data Timeout Multiplier */
@@ -28,6 +40,7 @@
 # define MCI_SDCSEL_MASK	(  3 <<  0)
 # define MCI_SDCBUS_1BIT	(  0 <<  6)	/* 1-bit data bus */
 # define MCI_SDCBUS_4BIT	(  2 <<  6)	/* 4-bit data bus */
+# define MCI_SDCBUS_8BIT	(  3 <<  6)	/* 8-bit data bus[2] */
 # define MCI_SDCBUS_MASK	(  3 <<  6)
 #define MCI_ARGR		0x0010	/* Command Argument */
 #define MCI_CMDR		0x0014	/* Command */
@@ -56,6 +69,9 @@
 #define MCI_BLKR		0x0018	/* Block */
 # define MCI_BCNT(x)		((x) <<  0)	/* Data Block Count */
 # define MCI_BLKLEN(x)		((x) << 16)	/* Data Block Length */
+#define MCI_CSTOR		0x001c	/* Completion Signal Timeout[2] */
+# define MCI_CSTOCYC(x)		((x) <<  0)	/* CST cycles */
+# define MCI_CSTOMUL(x)		((x) <<  4)	/* CST multiplier */
 #define MCI_RSPR		0x0020	/* Response 0 */
 #define MCI_RSPR1		0x0024	/* Response 1 */
 #define MCI_RSPR2		0x0028	/* Response 2 */
@@ -83,7 +99,24 @@
 # define MCI_DTOE		(  1 <<  22)	/* Data Time-Out Error */
 # define MCI_OVRE		(  1 <<  30)	/* RX Overrun Error */
 # define MCI_UNRE		(  1 <<  31)	/* TX Underrun Error */
+#define MCI_DMA			0x0050	/* DMA Configuration[2] */
+# define MCI_DMA_OFFSET(x)	((x) <<  0)	/* DMA Write Buffer Offset */
+# define MCI_DMA_CHKSIZE(x)	((x) <<  4)	/* DMA Channel Read and Write Chunk Size */
+# define MCI_DMAEN		(  1 <<  8)	/* DMA Hardware Handshaking Enable */
+#define MCI_CFG			0x0054	/* Configuration[2] */
+# define MCI_CFG_FIFOMODE_1DATA	(  1 <<  0)	/* MCI Internal FIFO control mode */
+# define MCI_CFG_FERRCTRL_COR	(  1 <<  4)	/* Flow Error flag reset control mode */
+# define MCI_CFG_HSMODE		(  1 <<  8)	/* High Speed Mode */
+# define MCI_CFG_LSYNC		(  1 << 12)	/* Synchronize on the last block */
+#define MCI_WPMR		0x00e4	/* Write Protection Mode[2] */
+# define MCI_WP_EN		(  1 <<  0)	/* WP Enable */
+# define MCI_WP_KEY		(0x4d4349 << 8)	/* WP Key */
+#define MCI_WPSR		0x00e8	/* Write Protection Status[2] */
+# define MCI_GET_WP_VS(x)	((x) & 0x0f)
+# define MCI_GET_WP_VSRC(x)	(((x) >> 8) & 0xffff)
+#define MCI_FIFO_APERTURE	0x0200	/* FIFO Aperture[2] */
 
+/* This is not including the FIFO Aperture on MCI2 */
 #define MCI_REGS_SIZE		0x100
 
 /* Register access macros */

drivers/mmc/host/cb710-mmc.h

+/*
+ *  cb710/cb710-mmc.h
+ *
+ *  Copyright by Michał Mirosław, 2008-2009
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef LINUX_CB710_MMC_H
+#define LINUX_CB710_MMC_H
+
+#include <linux/cb710.h>
+
+/* per-MMC-reader structure */
+struct cb710_mmc_reader {
+	struct tasklet_struct finish_req_tasklet;
+	struct mmc_request *mrq;
+	spinlock_t irq_lock;
+	unsigned char last_power_mode;
+};
+
+/* some device struct walking */
+
+static inline struct mmc_host *cb710_slot_to_mmc(struct cb710_slot *slot)
+{
+	return dev_get_drvdata(&slot->pdev.dev);
+}
+
+static inline struct cb710_slot *cb710_mmc_to_slot(struct mmc_host *mmc)
+{
+	struct platform_device *pdev = container_of(mmc_dev(mmc),
+		struct platform_device, dev);
+	return cb710_pdev_to_slot(pdev);
+}
+
+/* registers (this might be all wrong ;) */
+
+#define CB710_MMC_DATA_PORT		0x00
+
+#define CB710_MMC_CONFIG_PORT		0x04
+#define CB710_MMC_CONFIG0_PORT		0x04
+#define CB710_MMC_CONFIG1_PORT		0x05
+#define   CB710_MMC_C1_4BIT_DATA_BUS		0x40
+#define CB710_MMC_CONFIG2_PORT		0x06
+#define   CB710_MMC_C2_READ_PIO_SIZE_MASK	0x0F	/* N-1 */
+#define CB710_MMC_CONFIG3_PORT		0x07
+
+#define CB710_MMC_CONFIGB_PORT		0x08
+
+#define CB710_MMC_IRQ_ENABLE_PORT	0x0C
+#define   CB710_MMC_IE_TEST_MASK		0x00BF
+#define   CB710_MMC_IE_CARD_INSERTION_STATUS	0x1000
+#define   CB710_MMC_IE_IRQ_ENABLE		0x8000
+#define   CB710_MMC_IE_CISTATUS_MASK		\
+		(CB710_MMC_IE_CARD_INSERTION_STATUS|CB710_MMC_IE_IRQ_ENABLE)
+
+#define CB710_MMC_STATUS_PORT		0x10
+#define   CB710_MMC_STATUS_ERROR_EVENTS		0x60FF
+#define CB710_MMC_STATUS0_PORT		0x10
+#define   CB710_MMC_S0_FIFO_UNDERFLOW		0x40
+#define CB710_MMC_STATUS1_PORT		0x11
+#define   CB710_MMC_S1_COMMAND_SENT		0x01
+#define   CB710_MMC_S1_DATA_TRANSFER_DONE	0x02
+#define   CB710_MMC_S1_PIO_TRANSFER_DONE	0x04
+#define   CB710_MMC_S1_CARD_CHANGED		0x10
+#define   CB710_MMC_S1_RESET			0x20
+#define CB710_MMC_STATUS2_PORT		0x12
+#define   CB710_MMC_S2_FIFO_READY		0x01
+#define   CB710_MMC_S2_FIFO_EMPTY		0x02
+#define   CB710_MMC_S2_BUSY_10			0x10
+#define   CB710_MMC_S2_BUSY_20			0x20
+#define CB710_MMC_STATUS3_PORT		0x13
+#define   CB710_MMC_S3_CARD_DETECTED		0x02
+#define   CB710_MMC_S3_WRITE_PROTECTED		0x04
+
+#define CB710_MMC_CMD_TYPE_PORT		0x14
+#define   CB710_MMC_RSP_TYPE_MASK		0x0007
+#define     CB710_MMC_RSP_R1			(0)
+#define     CB710_MMC_RSP_136			(5)
+#define     CB710_MMC_RSP_NO_CRC		(2)
+#define   CB710_MMC_RSP_PRESENT_MASK		0x0018
+#define     CB710_MMC_RSP_NONE			(0 << 3)
+#define     CB710_MMC_RSP_PRESENT		(1 << 3)
+#define     CB710_MMC_RSP_PRESENT_X		(2 << 3)
+#define   CB710_MMC_CMD_TYPE_MASK		0x0060
+#define     CB710_MMC_CMD_BC			(0 << 5)
+#define     CB710_MMC_CMD_BCR			(1 << 5)
+#define     CB710_MMC_CMD_AC			(2 << 5)
+#define     CB710_MMC_CMD_ADTC			(3 << 5)
+#define   CB710_MMC_DATA_READ			0x0080
+#define   CB710_MMC_CMD_CODE_MASK		0x3F00
+#define   CB710_MMC_CMD_CODE_SHIFT		8
+#define   CB710_MMC_IS_APP_CMD			0x4000
+#define   CB710_MMC_RSP_BUSY			0x8000
+
+#define CB710_MMC_CMD_PARAM_PORT	0x18
+#define CB710_MMC_TRANSFER_SIZE_PORT	0x1C
+#define CB710_MMC_RESPONSE0_PORT	0x20
+#define CB710_MMC_RESPONSE1_PORT	0x24
+#define CB710_MMC_RESPONSE2_PORT	0x28
+#define CB710_MMC_RESPONSE3_PORT	0x2C
+
+#endif /* LINUX_CB710_MMC_H */

drivers/mmc/host/mmc_spi.c

@@ -97,6 +97,14 @@
  */
 #define r1b_timeout		(HZ * 3)
 
+/* One of the critical speed parameters is the amount of data which may
+ * be transfered in one command. If this value is too low, the SD card
+ * controller has to do multiple partial block writes (argggh!). With
+ * today (2008) SD cards there is little speed gain if we transfer more
+ * than 64 KBytes at a time. So use this value until there is any indication
+ * that we should do more here.
+ */
+#define MMC_SPI_BLOCKSATONCE	128
 
 /****************************************************************************/
 
@@ -327,15 +335,16 @@ static int mmc_spi_response_get(struct mmc_spi_host *host,
 
 	/* Status byte: the entire seven-bit R1 response.  */
 	if (cmd->resp[0] != 0) {
-		if ((R1_SPI_PARAMETER | R1_SPI_ADDRESS
-				      | R1_SPI_ILLEGAL_COMMAND)
+		if ((R1_SPI_PARAMETER | R1_SPI_ADDRESS)
 				& cmd->resp[0])
-			value = -EINVAL;
+			value = -EFAULT; /* Bad address */
+		else if (R1_SPI_ILLEGAL_COMMAND & cmd->resp[0])
+			value = -ENOSYS; /* Function not implemented */
 		else if (R1_SPI_COM_CRC & cmd->resp[0])
-			value = -EILSEQ;
+			value = -EILSEQ; /* Illegal byte sequence */
 		else if ((R1_SPI_ERASE_SEQ | R1_SPI_ERASE_RESET)
 				& cmd->resp[0])
-			value = -EIO;
+			value = -EIO;    /* I/O error */
 		/* else R1_SPI_IDLE, "it's resetting" */
 	}
 
@@ -1366,6 +1375,10 @@ static int mmc_spi_probe(struct spi_device *spi)
 
 	mmc->ops = &mmc_spi_ops;
 	mmc->max_blk_size = MMC_SPI_BLOCKSIZE;
+	mmc->max_hw_segs = MMC_SPI_BLOCKSATONCE;
+	mmc->max_phys_segs = MMC_SPI_BLOCKSATONCE;
+	mmc->max_req_size = MMC_SPI_BLOCKSATONCE * MMC_SPI_BLOCKSIZE;
+	mmc->max_blk_count = MMC_SPI_BLOCKSATONCE;
 
 	mmc->caps = MMC_CAP_SPI;
 

drivers/mmc/host/mxcmmc.c

@@ -746,8 +746,6 @@ static int mxcmci_probe(struct platform_device *pdev)
 	}
 
 	mmc->f_min = clk_get_rate(host->clk) >> 16;
-	if (mmc->f_min < 400000)
-		mmc->f_min = 400000;
 	mmc->f_max = clk_get_rate(host->clk) >> 1;
 
 	/* recommended in data sheet */

drivers/mmc/host/omap.c

@@ -1593,7 +1593,6 @@ static int mmc_omap_resume(struct platform_device *pdev)
 #endif
 
 static struct platform_driver mmc_omap_driver = {
-	.probe		= mmc_omap_probe,
 	.remove		= mmc_omap_remove,
 	.suspend	= mmc_omap_suspend,
 	.resume		= mmc_omap_resume,
@@ -1605,7 +1604,7 @@ static struct platform_driver mmc_omap_driver = {
 
 static int __init mmc_omap_init(void)
 {
-	return platform_driver_register(&mmc_omap_driver);
+	return platform_driver_probe(&mmc_omap_driver, mmc_omap_probe);
 }
 
 static void __exit mmc_omap_exit(void)

drivers/mmc/host/pxamci.c

@@ -27,6 +27,7 @@
 #include <linux/err.h>
 #include <linux/mmc/host.h>
 #include <linux/io.h>
+#include <linux/regulator/consumer.h>
 
 #include <asm/sizes.h>
 
@@ -67,8 +68,42 @@ struct pxamci_host {
 	unsigned int		dma_dir;
 	unsigned int		dma_drcmrrx;
 	unsigned int		dma_drcmrtx;
+
+	struct regulator	*vcc;
 };
 
+static inline void pxamci_init_ocr(struct pxamci_host *host)
+{
+#ifdef CONFIG_REGULATOR
+	host->vcc = regulator_get(mmc_dev(host->mmc), "vmmc");
+
+	if (IS_ERR(host->vcc))
+		host->vcc = NULL;
+	else {
+		host->mmc->ocr_avail = mmc_regulator_get_ocrmask(host->vcc);
+		if (host->pdata && host->pdata->ocr_mask)
+			dev_warn(mmc_dev(host->mmc),
+				"ocr_mask/setpower will not be used\n");
+	}
+#endif
+	if (host->vcc == NULL) {
+		/* fall-back to platform data */
+		host->mmc->ocr_avail = host->pdata ?
+			host->pdata->ocr_mask :
+			MMC_VDD_32_33 | MMC_VDD_33_34;
+	}
+}
+
+static inline void pxamci_set_power(struct pxamci_host *host, unsigned int vdd)
+{
+#ifdef CONFIG_REGULATOR
+	if (host->vcc)
+		mmc_regulator_set_ocr(host->vcc, vdd);
+#endif
+	if (!host->vcc && host->pdata && host->pdata->setpower)
+		host->pdata->setpower(mmc_dev(host->mmc), vdd);
+}
+
 static void pxamci_stop_clock(struct pxamci_host *host)
 {
 	if (readl(host->base + MMC_STAT) & STAT_CLK_EN) {
@@ -438,8 +473,7 @@ static void pxamci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 	if (host->power_mode != ios->power_mode) {
 		host->power_mode = ios->power_mode;
 
-		if (host->pdata && host->pdata->setpower)
-			host->pdata->setpower(mmc_dev(mmc), ios->vdd);
+		pxamci_set_power(host, ios->vdd);
 
 		if (ios->power_mode == MMC_POWER_ON)
 			host->cmdat |= CMDAT_INIT;
@@ -562,9 +596,8 @@ static int pxamci_probe(struct platform_device *pdev)
 	mmc->f_max = (cpu_is_pxa300() || cpu_is_pxa310()) ? 26000000
 							  : host->clkrate;
 
-	mmc->ocr_avail = host->pdata ?
-			 host->pdata->ocr_mask :
-			 MMC_VDD_32_33|MMC_VDD_33_34;
+	pxamci_init_ocr(host);
+
 	mmc->caps = 0;
 	host->cmdat = 0;
 	if (!cpu_is_pxa25x()) {
@@ -661,6 +694,9 @@ static int pxamci_remove(struct platform_device *pdev)
 	if (mmc) {
 		struct pxamci_host *host = mmc_priv(mmc);
 
+		if (host->vcc)
+			regulator_put(host->vcc);
+
 		if (host->pdata && host->pdata->exit)
 			host->pdata->exit(&pdev->dev, mmc);
 

drivers/mmc/host/sdhci-pltfm.c

+/*
+ * sdhci-pltfm.c Support for SDHCI platform devices
+ * Copyright (c) 2009 Intel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+/* Supports:
+ * SDHCI platform devices
+ *
+ * Inspired by sdhci-pci.c, by Pierre Ossman
+ */
+
+#include <linux/delay.h>
+#include <linux/highmem.h>
+#include <linux/platform_device.h>
+
+#include <linux/mmc/host.h>
+
+#include <linux/io.h>
+
+#include "sdhci.h"
+
+/*****************************************************************************\
+ *                                                                           *
+ * SDHCI core callbacks                                                      *
+ *                                                                           *
+\*****************************************************************************/
+
+static struct sdhci_ops sdhci_pltfm_ops = {
+};
+
+/*****************************************************************************\
+ *                                                                           *
+ * Device probing/removal                                                    *
+ *                                                                           *
+\*****************************************************************************/
+
+static int __devinit sdhci_pltfm_probe(struct platform_device *pdev)
+{
+	struct sdhci_host *host;
+	struct resource *iomem;
+	int ret;
+
+	BUG_ON(pdev == NULL);
+
+	iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!iomem) {
+		ret = -ENOMEM;
+		goto err;
+	}
+
+	if (resource_size(iomem) != 0x100)
+		dev_err(&pdev->dev, "Invalid iomem size. You may "
+			"experience problems.\n");
+
+	if (pdev->dev.parent)
+		host = sdhci_alloc_host(pdev->dev.parent, 0);
+	else
+		host = sdhci_alloc_host(&pdev->dev, 0);
+
+	if (IS_ERR(host)) {
+		ret = PTR_ERR(host);
+		goto err;
+	}
+
+	host->hw_name = "platform";
+	host->ops = &sdhci_pltfm_ops;
+	host->irq = platform_get_irq(pdev, 0);
+
+	if (!request_mem_region(iomem->start, resource_size(iomem),
+		mmc_hostname(host->mmc))) {
+		dev_err(&pdev->dev, "cannot request region\n");
+		ret = -EBUSY;
+		goto err_request;
+	}
+
+	host->ioaddr = ioremap(iomem->start, resource_size(iomem));
+	if (!host->ioaddr) {
+		dev_err(&pdev->dev, "failed to remap registers\n");
+		ret = -ENOMEM;
+		goto err_remap;
+	}
+
+	ret = sdhci_add_host(host);
+	if (ret)
+		goto err_add_host;
+
+	platform_set_drvdata(pdev, host);
+
+	return 0;
+
+err_add_host:
+	iounmap(host->ioaddr);
+err_remap:
+	release_mem_region(iomem->start, resource_size(iomem));
+err_request:
+	sdhci_free_host(host);
+err:
+	printk(KERN_ERR"Probing of sdhci-pltfm failed: %d\n", ret);
+	return ret;
+}
+
+static int __devexit sdhci_pltfm_remove(struct platform_device *pdev)
+{
+	struct sdhci_host *host = platform_get_drvdata(pdev);
+	struct resource *iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	int dead;
+	u32 scratch;
+
+	dead = 0;
+	scratch = readl(host->ioaddr + SDHCI_INT_STATUS);
+	if (scratch == (u32)-1)
+		dead = 1;
+
+	sdhci_remove_host(host, dead);
+	iounmap(host->ioaddr);
+	release_mem_region(iomem->start, resource_size(iomem));
+	sdhci_free_host(host);
+	platform_set_drvdata(pdev, NULL);
+
+	return 0;
+}
+
+static struct platform_driver sdhci_pltfm_driver = {
+	.driver = {
+		.name	= "sdhci",
+		.owner	= THIS_MODULE,
+	},
+	.probe		= sdhci_pltfm_probe,
+	.remove		= __devexit_p(sdhci_pltfm_remove),
+};
+
+/*****************************************************************************\
+ *                                                                           *
+ * Driver init/exit                                                          *
+ *                                                                           *
+\*****************************************************************************/
+
+static int __init sdhci_drv_init(void)
+{
+	return platform_driver_register(&sdhci_pltfm_driver);
+}
+
+static void __exit sdhci_drv_exit(void)
+{
+	platform_driver_unregister(&sdhci_pltfm_driver);
+}
+
+module_init(sdhci_drv_init);
+module_exit(sdhci_drv_exit);
+
+MODULE_DESCRIPTION("Secure Digital Host Controller Interface platform driver");
+MODULE_AUTHOR("Mocean Laboratories <info@mocean-labs.com>");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:sdhci");
+

drivers/mmc/host/sdhci.c

@@ -78,6 +78,11 @@ static void sdhci_dumpregs(struct sdhci_host *host)
 		sdhci_readl(host, SDHCI_CAPABILITIES),
 		sdhci_readl(host, SDHCI_MAX_CURRENT));
 
+	if (host->flags & SDHCI_USE_ADMA)
+		printk(KERN_DEBUG DRIVER_NAME ": ADMA Err: 0x%08x | ADMA Ptr: 0x%08x\n",
+		       readl(host->ioaddr + SDHCI_ADMA_ERROR),
+		       readl(host->ioaddr + SDHCI_ADMA_ADDRESS));
+
 	printk(KERN_DEBUG DRIVER_NAME ": ===========================================\n");
 }
 
@@ -1005,12 +1010,34 @@ static void sdhci_set_power(struct sdhci_host *host, unsigned short power)
 {
 	u8 pwr;
 
-	if (host->power == power)
+	if (power == (unsigned short)-1)
+		pwr = 0;
+	else {
+		switch (1 << power) {
+		case MMC_VDD_165_195:
+			pwr = SDHCI_POWER_180;
+			break;
+		case MMC_VDD_29_30:
+		case MMC_VDD_30_31:
+			pwr = SDHCI_POWER_300;
+			break;
+		case MMC_VDD_32_33:
+		case MMC_VDD_33_34:
+			pwr = SDHCI_POWER_330;
+			break;
+		default:
+			BUG();
+		}
+	}
+
+	if (host->pwr == pwr)
 		return;
 
-	if (power == (unsigned short)-1) {
+	host->pwr = pwr;
+
+	if (pwr == 0) {
 		sdhci_writeb(host, 0, SDHCI_POWER_CONTROL);
-		goto out;
+		return;
 	}
 
 	/*
@@ -1020,35 +1047,16 @@ static void sdhci_set_power(struct sdhci_host *host, unsigned short power)
 	if (!(host->quirks & SDHCI_QUIRK_SINGLE_POWER_WRITE))
 		sdhci_writeb(host, 0, SDHCI_POWER_CONTROL);
 
-	pwr = SDHCI_POWER_ON;
-
-	switch (1 << power) {
-	case MMC_VDD_165_195:
-		pwr |= SDHCI_POWER_180;
-		break;
-	case MMC_VDD_29_30:
-	case MMC_VDD_30_31:
-		pwr |= SDHCI_POWER_300;
-		break;
-	case MMC_VDD_32_33:
-	case MMC_VDD_33_34:
-		pwr |= SDHCI_POWER_330;
-		break;
-	default:
-		BUG();
-	}
-
 	/*
 	 * At least the Marvell CaFe chip gets confused if we set the voltage
 	 * and set turn on power at the same time, so set the voltage first.
 	 */
 	if ((host->quirks & SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER))
-		sdhci_writeb(host, pwr & ~SDHCI_POWER_ON, SDHCI_POWER_CONTROL);
+		sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
 
-	sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
+	pwr |= SDHCI_POWER_ON;
 
-out:
-	host->power = power;
+	sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
 }
 
 /*****************************************************************************\

drivers/mmc/host/sdhci.h

@@ -255,7 +255,7 @@ struct sdhci_host {
 	unsigned int		timeout_clk;	/* Timeout freq (KHz) */
 
 	unsigned int		clock;		/* Current clock (MHz) */
-	unsigned short		power;		/* Current voltage */
+	u8			pwr;		/* Current voltage */
 
 	struct mmc_request	*mrq;		/* Current request */
 	struct mmc_command	*cmd;		/* Current command */

drivers/mmc/host/tmio_mmc.h

@@ -83,34 +83,36 @@
 		TMIO_STAT_CARD_REMOVE | TMIO_STAT_CARD_INSERT)
 #define TMIO_MASK_IRQ     (TMIO_MASK_READOP | TMIO_MASK_WRITEOP | TMIO_MASK_CMD)
 
-#define enable_mmc_irqs(ctl, i) \
+
+#define enable_mmc_irqs(host, i) \
 	do { \
 		u32 mask;\
-		mask  = tmio_ioread32((ctl) + CTL_IRQ_MASK); \
+		mask  = sd_ctrl_read32((host), CTL_IRQ_MASK); \
 		mask &= ~((i) & TMIO_MASK_IRQ); \
-		tmio_iowrite32(mask, (ctl) + CTL_IRQ_MASK); \
+		sd_ctrl_write32((host), CTL_IRQ_MASK, mask); \
 	} while (0)
 
-#define disable_mmc_irqs(ctl, i) \
+#define disable_mmc_irqs(host, i) \
 	do { \
 		u32 mask;\
-		mask  = tmio_ioread32((ctl) + CTL_IRQ_MASK); \
+		mask  = sd_ctrl_read32((host), CTL_IRQ_MASK); \
 		mask |= ((i) & TMIO_MASK_IRQ); \
-		tmio_iowrite32(mask, (ctl) + CTL_IRQ_MASK); \
+		sd_ctrl_write32((host), CTL_IRQ_MASK, mask); \
 	} while (0)
 
-#define ack_mmc_irqs(ctl, i) \
+#define ack_mmc_irqs(host, i) \
 	do { \
 		u32 mask;\
-		mask  = tmio_ioread32((ctl) + CTL_STATUS); \
+		mask  = sd_ctrl_read32((host), CTL_STATUS); \
 		mask &= ~((i) & TMIO_MASK_IRQ); \
-		tmio_iowrite32(mask, (ctl) + CTL_STATUS); \
+		sd_ctrl_write32((host), CTL_STATUS, mask); \
 	} while (0)
 
 
 struct tmio_mmc_host {
 	void __iomem *cnf;
 	void __iomem *ctl;
+	unsigned long bus_shift;
 	struct mmc_command      *cmd;
 	struct mmc_request      *mrq;
 	struct mmc_data         *data;
@@ -123,6 +125,63 @@ struct tmio_mmc_host {
 	unsigned int            sg_off;
 };
 
+#include <linux/io.h>
+
+static inline u16 sd_ctrl_read16(struct tmio_mmc_host *host, int addr)
+{
+	return readw(host->ctl + (addr << host->bus_shift));
+}
+
+static inline void sd_ctrl_read16_rep(struct tmio_mmc_host *host, int addr,
+		u16 *buf, int count)
+{
+	readsw(host->ctl + (addr << host->bus_shift), buf, count);
+}
+
+static inline u32 sd_ctrl_read32(struct tmio_mmc_host *host, int addr)
+{
+	return readw(host->ctl + (addr << host->bus_shift)) |
+	       readw(host->ctl + ((addr + 2) << host->bus_shift)) << 16;
+}
+
+static inline void sd_ctrl_write16(struct tmio_mmc_host *host, int addr,
+		u16 val)
+{
+	writew(val, host->ctl + (addr << host->bus_shift));
+}
+
+static inline void sd_ctrl_write16_rep(struct tmio_mmc_host *host, int addr,
+		u16 *buf, int count)
+{
+	writesw(host->ctl + (addr << host->bus_shift), buf, count);
+}
+
+static inline void sd_ctrl_write32(struct tmio_mmc_host *host, int addr,
+		u32 val)
+{
+	writew(val, host->ctl + (addr << host->bus_shift));
+	writew(val >> 16, host->ctl + ((addr + 2) << host->bus_shift));
+}
+
+static inline void sd_config_write8(struct tmio_mmc_host *host, int addr,
+		u8 val)
+{
+	writeb(val, host->cnf + (addr << host->bus_shift));
+}
+
+static inline void sd_config_write16(struct tmio_mmc_host *host, int addr,
+		u16 val)
+{
+	writew(val, host->cnf + (addr << host->bus_shift));
+}
+
+static inline void sd_config_write32(struct tmio_mmc_host *host, int addr,
+		u32 val)
+{
+	writew(val, host->cnf + (addr << host->bus_shift));
+	writew(val >> 16, host->cnf + ((addr + 2) << host->bus_shift));
+}
+
 #include <linux/scatterlist.h>
 #include <linux/blkdev.h>
 

include/linux/cb710.h

+/*
+ *  cb710/cb710.h
+ *
+ *  Copyright by Michał Mirosław, 2008-2009
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef LINUX_CB710_DRIVER_H
+#define LINUX_CB710_DRIVER_H
+
+#include <linux/io.h>
+#include <linux/interrupt.h>
+#include <linux/spinlock.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+#include <linux/mmc/host.h>
+
+struct cb710_slot;
+
+typedef int (*cb710_irq_handler_t)(struct cb710_slot *);
+
+/* per-virtual-slot structure */
+struct cb710_slot {
+	struct platform_device	pdev;
+	void __iomem		*iobase;
+	cb710_irq_handler_t	irq_handler;
+};
+
+/* per-device structure */
+struct cb710_chip {
+	struct pci_dev		*pdev;
+	void __iomem		*iobase;
+	unsigned		platform_id;
+#ifdef CONFIG_CB710_DEBUG_ASSUMPTIONS
+	atomic_t		slot_refs_count;
+#endif
+	unsigned		slot_mask;
+	unsigned		slots;
+	spinlock_t		irq_lock;
+	struct cb710_slot	slot[0];
+};
+
+/* NOTE: cb710_chip.slots is modified only during device init/exit and
+ * they are all serialized wrt themselves */
+
+/* cb710_chip.slot_mask values */
+#define CB710_SLOT_MMC		1
+#define CB710_SLOT_MS		2
+#define CB710_SLOT_SM		4
+
+/* slot port accessors - so the logic is more clear in the code */
+#define CB710_PORT_ACCESSORS(t) \
+static inline void cb710_write_port_##t(struct cb710_slot *slot,	\
+	unsigned port, u##t value)					\
+{									\
+	iowrite##t(value, slot->iobase + port);				\
+}									\
+									\
+static inline u##t cb710_read_port_##t(struct cb710_slot *slot,		\
+	unsigned port)							\
+{									\
+	return ioread##t(slot->iobase + port);				\
+}									\
+									\
+static inline void cb710_modify_port_##t(struct cb710_slot *slot,	\
+	unsigned port, u##t set, u##t clear)				\
+{									\
+	iowrite##t(							\
+		(ioread##t(slot->iobase + port) & ~clear)|set,		\
+		slot->iobase + port);					\
+}
+
+CB710_PORT_ACCESSORS(8)
+CB710_PORT_ACCESSORS(16)
+CB710_PORT_ACCESSORS(32)
+
+void cb710_pci_update_config_reg(struct pci_dev *pdev,
+	int reg, uint32_t and, uint32_t xor);
+void cb710_set_irq_handler(struct cb710_slot *slot,
+	cb710_irq_handler_t handler);
+
+/* some device struct walking */
+
+static inline struct cb710_slot *cb710_pdev_to_slot(
+	struct platform_device *pdev)
+{
+	return container_of(pdev, struct cb710_slot, pdev);
+}
+
+static inline struct cb710_chip *cb710_slot_to_chip(struct cb710_slot *slot)
+{
+	return dev_get_drvdata(slot->pdev.dev.parent);
+}
+
+static inline struct device *cb710_slot_dev(struct cb710_slot *slot)
+{
+	return &slot->pdev.dev;
+}
+
+static inline struct device *cb710_chip_dev(struct cb710_chip *chip)
+{
+	return &chip->pdev->dev;
+}
+
+/* debugging aids */
+
+#ifdef CONFIG_CB710_DEBUG
+void cb710_dump_regs(struct cb710_chip *chip, unsigned dump);
+#else
+#define cb710_dump_regs(c, d) do {} while (0)
+#endif
+
+#define CB710_DUMP_REGS_MMC	0x0F
+#define CB710_DUMP_REGS_MS	0x30
+#define CB710_DUMP_REGS_SM	0xC0
+#define CB710_DUMP_REGS_ALL	0xFF
+#define CB710_DUMP_REGS_MASK	0xFF
+
+#define CB710_DUMP_ACCESS_8	0x100
+#define CB710_DUMP_ACCESS_16	0x200
+#define CB710_DUMP_ACCESS_32	0x400
+#define CB710_DUMP_ACCESS_ALL	0x700
+#define CB710_DUMP_ACCESS_MASK	0x700
+
+#endif /* LINUX_CB710_DRIVER_H */
+/*
+ *  cb710/sgbuf2.h
+ *
+ *  Copyright by Michał Mirosław, 2008-2009
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef LINUX_CB710_SG_H
+#define LINUX_CB710_SG_H
+
+#include <linux/highmem.h>
+#include <linux/scatterlist.h>
+
+/**
+ * cb710_sg_miter_stop_writing - stop mapping iteration after writing
+ * @miter: sg mapping iter to be stopped
+ *
+ * Description:
+ *   Stops mapping iterator @miter.  @miter should have been started
+ *   started using sg_miter_start().  A stopped iteration can be
+ *   resumed by calling sg_miter_next() on it.  This is useful when
+ *   resources (kmap) need to be released during iteration.
+ *
+ *   This is a convenience wrapper that will be optimized out for arches
+ *   that don't need flush_kernel_dcache_page().
+ *
+ * Context:
+ *   IRQ disabled if the SG_MITER_ATOMIC is set.  Don't care otherwise.
+ */
+static inline void cb710_sg_miter_stop_writing(struct sg_mapping_iter *miter)
+{
+	if (miter->page)
+		flush_kernel_dcache_page(miter->page);
+	sg_miter_stop(miter);
+}
+
+/*
+ * 32-bit PIO mapping sg iterator
+ *
+ * Hides scatterlist access issues - fragment boundaries, alignment, page
+ * mapping - for drivers using 32-bit-word-at-a-time-PIO (ie. PCI devices
+ * without DMA support).
+ *
+ * Best-case reading (transfer from device):
+ *   sg_miter_start();
+ *   cb710_sg_dwiter_write_from_io();
+ *   cb710_sg_miter_stop_writing();
+ *
+ * Best-case writing (transfer to device):
+ *   sg_miter_start();
+ *   cb710_sg_dwiter_read_to_io();
+ *   sg_miter_stop();
+ */
+
+uint32_t cb710_sg_dwiter_read_next_block(struct sg_mapping_iter *miter);
+void cb710_sg_dwiter_write_next_block(struct sg_mapping_iter *miter, uint32_t data);
+
+/**
+ * cb710_sg_dwiter_write_from_io - transfer data to mapped buffer from 32-bit IO port
+ * @miter: sg mapping iter
+ * @port: PIO port - IO or MMIO address
+ * @count: number of 32-bit words to transfer
+ *
+ * Description:
+ *   Reads @count 32-bit words from register @port and stores it in
+ *   buffer iterated by @miter.  Data that would overflow the buffer
+ *   is silently ignored.  Iterator is advanced by 4*@count bytes
+ *   or to the buffer's end whichever is closer.
+ *
+ * Context:
+ *   IRQ disabled if the SG_MITER_ATOMIC is set.  Don't care otherwise.
+ */
+static inline void cb710_sg_dwiter_write_from_io(struct sg_mapping_iter *miter,
+	void __iomem *port, size_t count)
+{
+	while (count-- > 0)
+		cb710_sg_dwiter_write_next_block(miter, ioread32(port));
+}
+
+/**
+ * cb710_sg_dwiter_read_to_io - transfer data to 32-bit IO port from mapped buffer
+ * @miter: sg mapping iter
+ * @port: PIO port - IO or MMIO address
+ * @count: number of 32-bit words to transfer
+ *
+ * Description:
+ *   Writes @count 32-bit words to register @port from buffer iterated
+ *   through @miter.  If buffer ends before @count words are written
+ *   missing data is replaced by zeroes. @miter is advanced by 4*@count
+ *   bytes or to the buffer's end whichever is closer.
+ *
+ * Context:
+ *   IRQ disabled if the SG_MITER_ATOMIC is set.  Don't care otherwise.
+ */
+static inline void cb710_sg_dwiter_read_to_io(struct sg_mapping_iter *miter,
+	void __iomem *port, size_t count)
+{
+	while (count-- > 0)
+		iowrite32(cb710_sg_dwiter_read_next_block(miter), port);
+}
+
+#endif /* LINUX_CB710_SG_H */

include/linux/mfd/tmio.h

@@ -18,6 +18,13 @@
 	writew((val) >> 16, (addr) + 2); \
 	} while (0)
 
+/*
+ * data for the MMC controller
+ */
+struct tmio_mmc_data {
+	unsigned int		hclk;
+};
+
 /*
  * data for the NAND controller
  */

include/linux/pci_ids.h

@@ -2127,6 +2127,7 @@
 #define PCI_VENDOR_ID_MAINPINE		0x1522
 #define PCI_DEVICE_ID_MAINPINE_PBRIDGE	0x0100
 #define PCI_VENDOR_ID_ENE		0x1524
+#define PCI_DEVICE_ID_ENE_CB710_FLASH	0x0510
 #define PCI_DEVICE_ID_ENE_CB712_SD	0x0550
 #define PCI_DEVICE_ID_ENE_CB712_SD_2	0x0551
 #define PCI_DEVICE_ID_ENE_CB714_SD	0x0750