ptp: ixp46x: move adjacent to ethernet driver

The ixp46x ptp driver has a somewhat unusual setup, where the ptp
driver and the ethernet driver are in different directories but
access the same registers that are defined a platform specific
header file.

Moving everything into drivers/net/ makes it look more like most
other ptp drivers and allows compile-testing this driver on
other targets.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

drivers/net/ethernet/xscale/Kconfig

@@ -27,4 +27,18 @@ config IXP4XX_ETH
 	  Say Y here if you want to use built-in Ethernet ports
 	  on IXP4xx processor.
 
+config PTP_1588_CLOCK_IXP46X
+	tristate "Intel IXP46x as PTP clock"
+	depends on IXP4XX_ETH
+	depends on PTP_1588_CLOCK
+	default y
+	help
+	  This driver adds support for using the IXP46X as a PTP
+	  clock. This clock is only useful if your PTP programs are
+	  getting hardware time stamps on the PTP Ethernet packets
+	  using the SO_TIMESTAMPING API.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called ptp_ixp46x.
+
 endif # NET_VENDOR_XSCALE

drivers/net/ethernet/xscale/Makefile

@@ -3,4 +3,5 @@
 # Makefile for the Intel XScale IXP device drivers.
 #
 
-obj-$(CONFIG_IXP4XX_ETH) += ixp4xx_eth.o
+obj-$(CONFIG_IXP4XX_ETH)		+= ixp4xx_eth.o
+obj-$(CONFIG_PTP_1588_CLOCK_IXP46X)	+= ptp_ixp46x.o

drivers/net/ethernet/xscale/ixp4xx_eth.c

@@ -33,10 +33,11 @@
 #include <linux/ptp_classify.h>
 #include <linux/slab.h>
 #include <linux/module.h>
-#include <mach/ixp46x_ts.h>
 #include <linux/soc/ixp4xx/npe.h>
 #include <linux/soc/ixp4xx/qmgr.h>
 
+#include "ixp46x_ts.h"
+
 #define DEBUG_DESC		0
 #define DEBUG_RX		0
 #define DEBUG_TX		0

drivers/ptp/ptp_ixp46x.c → drivers/net/ethernet/xscale/ptp_ixp46x.c

@@ -15,7 +15,8 @@
 #include <linux/module.h>
 
 #include <linux/ptp_clock_kernel.h>
-#include <mach/ixp46x_ts.h>
+
+#include "ixp46x_ts.h"
 
 #define DRIVER		"ptp_ixp46x"
 #define N_EXT_TS	2

drivers/ptp/Kconfig

@@ -56,20 +56,6 @@ config PTP_1588_CLOCK_QORIQ
 	  To compile this driver as a module, choose M here: the module
 	  will be called ptp-qoriq.
 
-config PTP_1588_CLOCK_IXP46X
-	tristate "Intel IXP46x as PTP clock"
-	depends on IXP4XX_ETH
-	depends on PTP_1588_CLOCK
-	default y
-	help
-	  This driver adds support for using the IXP46X as a PTP
-	  clock. This clock is only useful if your PTP programs are
-	  getting hardware time stamps on the PTP Ethernet packets
-	  using the SO_TIMESTAMPING API.
-
-	  To compile this driver as a module, choose M here: the module
-	  will be called ptp_ixp46x.
-
 comment "Enable PHYLIB and NETWORK_PHY_TIMESTAMPING to see the additional clocks."
 	depends on PHYLIB=n || NETWORK_PHY_TIMESTAMPING=n
 

drivers/ptp/Makefile

@@ -7,10 +7,9 @@ ptp-y					:= ptp_clock.o ptp_chardev.o ptp_sysfs.o
 obj-$(CONFIG_PTP_1588_CLOCK)		+= ptp.o
 obj-$(CONFIG_PTP_1588_CLOCK_DTE)	+= ptp_dte.o
 obj-$(CONFIG_PTP_1588_CLOCK_INES)	+= ptp_ines.o
-obj-$(CONFIG_PTP_1588_CLOCK_IXP46X)	+= ptp_ixp46x.o
 obj-$(CONFIG_PTP_1588_CLOCK_PCH)	+= ptp_pch.o
 obj-$(CONFIG_PTP_1588_CLOCK_KVM)	+= ptp_kvm.o
 obj-$(CONFIG_PTP_1588_CLOCK_QORIQ)	+= ptp-qoriq.o
 ptp-qoriq-y				+= ptp_qoriq.o
 ptp-qoriq-$(CONFIG_DEBUG_FS)		+= ptp_qoriq_debugfs.o
-obj-$(CONFIG_PTP_1588_CLOCK_IDTCM)	+= ptp_clockmatrix.o
+obj-$(CONFIG_PTP_1588_CLOCK_IDTCM)	+= ptp_clockmatrix.o
\ No newline at end of file