sata_mv: use new sata phy register settings for new devices

Marvell's new SoC (65 nano) needs different settings for its SATA
PHY registers.
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

drivers/ata/sata_mv.c

@@ -293,6 +293,10 @@ enum {
 	FISCFG_WAIT_DEV_ERR	= (1 << 8),	/* wait for host on DevErr */
 	FISCFG_SINGLE_SYNC	= (1 << 16),	/* SYNC on DMA activation */
 
+	PHY_MODE9_GEN2		= 0x398,
+	PHY_MODE9_GEN1		= 0x39c,
+	PHYCFG_OFS		= 0x3a0,	/* only in 65n devices */
+
 	MV5_PHY_MODE		= 0x74,
 	MV5_LTMODE		= 0x30,
 	MV5_PHY_CTL		= 0x0C,
@@ -609,6 +613,8 @@ static int mv_soc_reset_hc(struct mv_host_priv *hpriv,
 static void mv_soc_reset_flash(struct mv_host_priv *hpriv,
 				      void __iomem *mmio);
 static void mv_soc_reset_bus(struct ata_host *host, void __iomem *mmio);
+static void mv_soc_65n_phy_errata(struct mv_host_priv *hpriv,
+				  void __iomem *mmio, unsigned int port);
 static void mv_reset_pci_bus(struct ata_host *host, void __iomem *mmio);
 static void mv_reset_channel(struct mv_host_priv *hpriv, void __iomem *mmio,
 			     unsigned int port_no);
@@ -807,6 +813,14 @@ static const struct mv_hw_ops mv_soc_ops = {
 	.reset_bus		= mv_soc_reset_bus,
 };
 
+static const struct mv_hw_ops mv_soc_65n_ops = {
+	.phy_errata		= mv_soc_65n_phy_errata,
+	.enable_leds		= mv_soc_enable_leds,
+	.reset_hc		= mv_soc_reset_hc,
+	.reset_flash		= mv_soc_reset_flash,
+	.reset_bus		= mv_soc_reset_bus,
+};
+
 /*
  * Functions
  */
@@ -3397,6 +3411,53 @@ static void mv_soc_reset_bus(struct ata_host *host, void __iomem *mmio)
 	return;
 }
 
+static void mv_soc_65n_phy_errata(struct mv_host_priv *hpriv,
+				  void __iomem *mmio, unsigned int port)
+{
+	void __iomem *port_mmio = mv_port_base(mmio, port);
+	u32	reg;
+
+	reg = readl(port_mmio + PHY_MODE3);
+	reg &= ~(0x3 << 27);	/* SELMUPF (bits 28:27) to 1 */
+	reg |= (0x1 << 27);
+	reg &= ~(0x3 << 29);	/* SELMUPI (bits 30:29) to 1 */
+	reg |= (0x1 << 29);
+	writel(reg, port_mmio + PHY_MODE3);
+
+	reg = readl(port_mmio + PHY_MODE4);
+	reg &= ~0x1;	/* SATU_OD8 (bit 0) to 0, reserved bit 16 must be set */
+	reg |= (0x1 << 16);
+	writel(reg, port_mmio + PHY_MODE4);
+
+	reg = readl(port_mmio + PHY_MODE9_GEN2);
+	reg &= ~0xf;	/* TXAMP[3:0] (bits 3:0) to 8 */
+	reg |= 0x8;
+	reg &= ~(0x1 << 14);	/* TXAMP[4] (bit 14) to 0 */
+	writel(reg, port_mmio + PHY_MODE9_GEN2);
+
+	reg = readl(port_mmio + PHY_MODE9_GEN1);
+	reg &= ~0xf;	/* TXAMP[3:0] (bits 3:0) to 8 */
+	reg |= 0x8;
+	reg &= ~(0x1 << 14);	/* TXAMP[4] (bit 14) to 0 */
+	writel(reg, port_mmio + PHY_MODE9_GEN1);
+}
+
+/**
+ *	soc_is_65 - check if the soc is 65 nano device
+ *
+ *	Detect the type of the SoC, this is done by reading the PHYCFG_OFS
+ *	register, this register should contain non-zero value and it exists only
+ *	in the 65 nano devices, when reading it from older devices we get 0.
+ */
+static bool soc_is_65n(struct mv_host_priv *hpriv)
+{
+	void __iomem *port0_mmio = mv_port_base(hpriv->base, 0);
+
+	if (readl(port0_mmio + PHYCFG_OFS))
+		return true;
+	return false;
+}
+
 static void mv_setup_ifcfg(void __iomem *port_mmio, int want_gen2i)
 {
 	u32 ifcfg = readl(port_mmio + SATA_IFCFG);
@@ -3737,7 +3798,10 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx)
 		}
 		break;
 	case chip_soc:
-		hpriv->ops = &mv_soc_ops;
+		if (soc_is_65n(hpriv))
+			hpriv->ops = &mv_soc_65n_ops;
+		else
+			hpriv->ops = &mv_soc_ops;
 		hp_flags |= MV_HP_FLAG_SOC | MV_HP_GEN_IIE |
 			MV_HP_ERRATA_60X1C0;
 		break;
@@ -3800,7 +3864,8 @@ static int mv_init_host(struct ata_host *host, unsigned int board_idx)
 	n_hc = mv_get_hc_count(host->ports[0]->flags);
 
 	for (port = 0; port < host->n_ports; port++)
-		hpriv->ops->read_preamp(hpriv, port, mmio);
+		if (hpriv->ops->read_preamp)
+			hpriv->ops->read_preamp(hpriv, port, mmio);
 
 	rc = hpriv->ops->reset_hc(hpriv, mmio, n_hc);
 	if (rc)