Merge tag 'usb-ci-v5.10-rc1' of...

Merge tag 'usb-ci-v5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next

Peter writes:

Two changes for chipidea imx driver:
- Add picophy parameter tuning interface
- Restore pinctrl for system suspend/resume

* tag 'usb-ci-v5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
  usb: chipidea: ci_hdrc_imx: restore pinctrl
  usb: chipidea: imx: add two samsung picophy parameters tuning implementation
  doc: dt-binding: ci-hdrc-usb2: add property for samsung picophy

Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt

@@ -100,6 +100,15 @@ i.mx specific properties
   It's recommended to specify the over current polarity.
 - power-active-high: power signal polarity is active high
 - external-vbus-divider: enables off-chip resistor divider for Vbus
+- samsung,picophy-pre-emp-curr-control: HS Transmitter Pre-Emphasis Current
+  Control. This signal controls the amount of current sourced to the
+  USB_OTG*_DP and USB_OTG*_DN pins after a J-to-K or K-to-J transition.
+  The range is from 0x0 to 0x3, the default value is 0x1.
+  Details can refer to TXPREEMPAMPTUNE0 bits of USBNC_n_PHY_CFG1.
+- samsung,picophy-dc-vol-level-adjust: HS DC Voltage Level Adjustment.
+  Adjust the high-speed transmitter DC level voltage.
+  The range is from 0x0 to 0xf, the default value is 0x3.
+  Details can refer to TXVREFTUNE0 bits of USBNC_n_PHY_CFG1.
 
 Example:
 

drivers/usb/chipidea/ci_hdrc_imx.c

@@ -165,6 +165,11 @@ static struct imx_usbmisc_data *usbmisc_get_init_data(struct device *dev)
 	if (of_usb_get_phy_mode(np) == USBPHY_INTERFACE_MODE_ULPI)
 		data->ulpi = 1;
 
+	of_property_read_u32(np, "samsung,picophy-pre-emp-curr-control",
+			&data->emp_curr_control);
+	of_property_read_u32(np, "samsung,picophy-dc-vol-level-adjust",
+			&data->dc_vol_level_adjust);
+
 	return data;
 }
 
@@ -609,7 +614,12 @@ static int __maybe_unused ci_hdrc_imx_suspend(struct device *dev)
 		}
 	}
 
-	return imx_controller_suspend(dev);
+	ret = imx_controller_suspend(dev);
+	if (ret)
+		return ret;
+
+	pinctrl_pm_select_sleep_state(dev);
+	return ret;
 }
 
 static int __maybe_unused ci_hdrc_imx_resume(struct device *dev)
@@ -617,6 +627,7 @@ static int __maybe_unused ci_hdrc_imx_resume(struct device *dev)
 	struct ci_hdrc_imx_data *data = dev_get_drvdata(dev);
 	int ret;
 
+	pinctrl_pm_select_default_state(dev);
 	ret = imx_controller_resume(dev);
 	if (!ret && data->supports_runtime_pm) {
 		pm_runtime_disable(dev);

drivers/usb/chipidea/ci_hdrc_imx.h

@@ -26,6 +26,8 @@ struct imx_usbmisc_data {
 	unsigned int ext_vbus:1; /* Vbus from exteranl event */
 	struct usb_phy *usb_phy;
 	enum usb_dr_mode available_role; /* runtime usb dr mode */
+	int emp_curr_control;
+	int dc_vol_level_adjust;
 };
 
 int imx_usbmisc_init(struct imx_usbmisc_data *data);

drivers/usb/chipidea/usbmisc_imx.c

@@ -128,6 +128,12 @@
 #define MX7D_USB_OTG_PHY_STATUS_VBUS_VLD	BIT(3)
 #define MX7D_USB_OTG_PHY_STATUS_CHRGDET		BIT(29)
 
+#define MX7D_USB_OTG_PHY_CFG1		0x30
+#define TXPREEMPAMPTUNE0_BIT		28
+#define TXPREEMPAMPTUNE0_MASK		(3 << 28)
+#define TXVREFTUNE0_BIT			20
+#define TXVREFTUNE0_MASK		(0xf << 20)
+
 #define MX6_USB_OTG_WAKEUP_BITS (MX6_BM_WAKEUP_ENABLE | MX6_BM_VBUS_WAKEUP | \
 				 MX6_BM_ID_WAKEUP)
 
@@ -649,6 +655,21 @@ static int usbmisc_imx7d_init(struct imx_usbmisc_data *data)
 		writel(reg | MX7D_USB_VBUS_WAKEUP_SOURCE_BVALID
 			| MX7D_USBNC_AUTO_RESUME,
 			usbmisc->base + MX7D_USBNC_USB_CTRL2);
+		/* PHY tuning for signal quality */
+		reg = readl(usbmisc->base + MX7D_USB_OTG_PHY_CFG1);
+		if (data->emp_curr_control && data->emp_curr_control <=
+			(TXPREEMPAMPTUNE0_MASK >> TXPREEMPAMPTUNE0_BIT)) {
+			reg &= ~TXPREEMPAMPTUNE0_MASK;
+			reg |= (data->emp_curr_control << TXPREEMPAMPTUNE0_BIT);
+		}
+
+		if (data->dc_vol_level_adjust && data->dc_vol_level_adjust <=
+			(TXVREFTUNE0_MASK >> TXVREFTUNE0_BIT)) {
+			reg &= ~TXVREFTUNE0_MASK;
+			reg |= (data->dc_vol_level_adjust << TXVREFTUNE0_BIT);
+		}
+
+		writel(reg, usbmisc->base + MX7D_USB_OTG_PHY_CFG1);
 	}
 
 	spin_unlock_irqrestore(&usbmisc->lock, flags);