Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next

Jeff Kirsher says:

====================
This series contains updates to e1000e, igb and ixgbe.

Bruce Allan provide 2 minor cleanups for e1000e to resolve whitespace
issues and build warnings about unused parameters.

Carolyn provides a couple of fixes for igb, one being a fix for a
possible panic when the interface is down and receive traffic
arrives.  The second fix resolves an issue on newer parts which have
multiple checksum fields and set_ethtool was only checking to update
the first checksum of the NVM image.

Akeem provides majority of the changes in this patch set.  Akeem
provides a fix for e1000e on an issue reported from the community to
resolve the issue of unlocking swflag_mutex for 82574 and 82583
devices even if the hardware semaphore was successfully acquired.
The other patches from Akeem are against igb, where he adds support
SFP module discovery, LED blink mechanism for devices using cathodes,
LED support for i210/i211 parts and cleanup of a i2c function which
was not being used.

Matthew provides an update for igb to support a more accurate check
for a PTP RX hang.

Amir provides a patch for ixgbe to set the software prio_tc values at
initialization to the hardware setting to remove the need to reset the
device at the first time we call ixgbe_dcbnl_ieee_setets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/intel/e1000e/80003es2lan.c

@@ -66,17 +66,17 @@ static s32 e1000_init_phy_params_80003es2lan(struct e1000_hw *hw)
 	s32 ret_val;
 
 	if (hw->phy.media_type != e1000_media_type_copper) {
-		phy->type	= e1000_phy_none;
+		phy->type = e1000_phy_none;
 		return 0;
 	} else {
 		phy->ops.power_up = e1000_power_up_phy_copper;
 		phy->ops.power_down = e1000_power_down_phy_copper_80003es2lan;
 	}
 
-	phy->addr		= 1;
-	phy->autoneg_mask	= AUTONEG_ADVERTISE_SPEED_DEFAULT;
-	phy->reset_delay_us      = 100;
-	phy->type		= e1000_phy_gg82563;
+	phy->addr = 1;
+	phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT;
+	phy->reset_delay_us = 100;
+	phy->type = e1000_phy_gg82563;
 
 	/* This can only be done after all function pointers are setup. */
 	ret_val = e1000e_get_phy_id(hw);
@@ -98,19 +98,19 @@ static s32 e1000_init_nvm_params_80003es2lan(struct e1000_hw *hw)
 	u32 eecd = er32(EECD);
 	u16 size;
 
-	nvm->opcode_bits	= 8;
-	nvm->delay_usec	 = 1;
+	nvm->opcode_bits = 8;
+	nvm->delay_usec = 1;
 	switch (nvm->override) {
 	case e1000_nvm_override_spi_large:
-		nvm->page_size    = 32;
+		nvm->page_size = 32;
 		nvm->address_bits = 16;
 		break;
 	case e1000_nvm_override_spi_small:
-		nvm->page_size    = 8;
+		nvm->page_size = 8;
 		nvm->address_bits = 8;
 		break;
 	default:
-		nvm->page_size    = eecd & E1000_EECD_ADDR_BITS ? 32 : 8;
+		nvm->page_size = eecd & E1000_EECD_ADDR_BITS ? 32 : 8;
 		nvm->address_bits = eecd & E1000_EECD_ADDR_BITS ? 16 : 8;
 		break;
 	}
@@ -128,7 +128,7 @@ static s32 e1000_init_nvm_params_80003es2lan(struct e1000_hw *hw)
 	/* EEPROM access above 16k is unsupported */
 	if (size > 14)
 		size = 14;
-	nvm->word_size	= 1 << size;
+	nvm->word_size = 1 << size;
 
 	return 0;
 }
@@ -859,7 +859,7 @@ static void e1000_initialize_hw_bits_80003es2lan(struct e1000_hw *hw)
 
 	/* Transmit Arbitration Control 0 */
 	reg = er32(TARC(0));
-	reg &= ~(0xF << 27); /* 30:27 */
+	reg &= ~(0xF << 27);	/* 30:27 */
 	if (hw->phy.media_type != e1000_media_type_copper)
 		reg &= ~(1 << 20);
 	ew32(TARC(0), reg);

drivers/net/ethernet/intel/e1000e/82571.c

@@ -77,24 +77,24 @@ static s32 e1000_init_phy_params_82571(struct e1000_hw *hw)
 		return 0;
 	}
 
-	phy->addr			 = 1;
-	phy->autoneg_mask		 = AUTONEG_ADVERTISE_SPEED_DEFAULT;
-	phy->reset_delay_us		 = 100;
+	phy->addr = 1;
+	phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT;
+	phy->reset_delay_us = 100;
 
-	phy->ops.power_up		 = e1000_power_up_phy_copper;
-	phy->ops.power_down		 = e1000_power_down_phy_copper_82571;
+	phy->ops.power_up = e1000_power_up_phy_copper;
+	phy->ops.power_down = e1000_power_down_phy_copper_82571;
 
 	switch (hw->mac.type) {
 	case e1000_82571:
 	case e1000_82572:
-		phy->type		 = e1000_phy_igp_2;
+		phy->type = e1000_phy_igp_2;
 		break;
 	case e1000_82573:
-		phy->type		 = e1000_phy_m88;
+		phy->type = e1000_phy_m88;
 		break;
 	case e1000_82574:
 	case e1000_82583:
-		phy->type		 = e1000_phy_bm;
+		phy->type = e1000_phy_bm;
 		phy->ops.acquire = e1000_get_hw_semaphore_82574;
 		phy->ops.release = e1000_put_hw_semaphore_82574;
 		phy->ops.set_d0_lplu_state = e1000_set_d0_lplu_state_82574;
@@ -193,7 +193,7 @@ static s32 e1000_init_nvm_params_82571(struct e1000_hw *hw)
 		/* EEPROM access above 16k is unsupported */
 		if (size > 14)
 			size = 14;
-		nvm->word_size	= 1 << size;
+		nvm->word_size = 1 << size;
 		break;
 	}
 
@@ -339,7 +339,7 @@ static s32 e1000_init_mac_params_82571(struct e1000_hw *hw)
 static s32 e1000_get_variants_82571(struct e1000_adapter *adapter)
 {
 	struct e1000_hw *hw = &adapter->hw;
-	static int global_quad_port_a; /* global port a indication */
+	static int global_quad_port_a;	/* global port a indication */
 	struct pci_dev *pdev = adapter->pdev;
 	int is_port_b = er32(STATUS) & E1000_STATUS_FUNC_1;
 	s32 rc;
@@ -1003,8 +1003,6 @@ static s32 e1000_reset_hw_82571(struct e1000_hw *hw)
 	default:
 		break;
 	}
-	if (ret_val)
-		e_dbg("Cannot acquire MDIO ownership\n");
 
 	ctrl = er32(CTRL);
 
@@ -1015,7 +1013,9 @@ static s32 e1000_reset_hw_82571(struct e1000_hw *hw)
 	switch (hw->mac.type) {
 	case e1000_82574:
 	case e1000_82583:
-		e1000_put_hw_semaphore_82574(hw);
+		/* Release mutex only if the hw semaphore is acquired */
+		if (!ret_val)
+			e1000_put_hw_semaphore_82574(hw);
 		break;
 	default:
 		break;
@@ -1178,7 +1178,7 @@ static void e1000_initialize_hw_bits_82571(struct e1000_hw *hw)
 
 	/* Transmit Arbitration Control 0 */
 	reg = er32(TARC(0));
-	reg &= ~(0xF << 27); /* 30:27 */
+	reg &= ~(0xF << 27);	/* 30:27 */
 	switch (hw->mac.type) {
 	case e1000_82571:
 	case e1000_82572:
@@ -1390,7 +1390,7 @@ bool e1000_check_phy_82574(struct e1000_hw *hw)
 	ret_val = e1e_rphy(hw, E1000_RECEIVE_ERROR_COUNTER, &receive_errors);
 	if (ret_val)
 		return false;
-	if (receive_errors == E1000_RECEIVE_ERROR_MAX)  {
+	if (receive_errors == E1000_RECEIVE_ERROR_MAX) {
 		ret_val = e1e_rphy(hw, E1000_BASE1000T_STATUS, &status_1kbt);
 		if (ret_val)
 			return false;

drivers/net/ethernet/intel/e1000e/ethtool.c

@@ -244,7 +244,7 @@ static int e1000_set_spd_dplx(struct e1000_adapter *adapter, u32 spd, u8 dplx)
 		mac->autoneg = 1;
 		adapter->hw.phy.autoneg_advertised = ADVERTISE_1000_FULL;
 		break;
-	case SPEED_1000 + DUPLEX_HALF: /* not supported */
+	case SPEED_1000 + DUPLEX_HALF:	/* not supported */
 	default:
 		goto err_inval;
 	}
@@ -416,7 +416,7 @@ static void e1000_set_msglevel(struct net_device *netdev, u32 data)
 
 static int e1000_get_regs_len(struct net_device __always_unused *netdev)
 {
-#define E1000_REGS_LEN 32 /* overestimate */
+#define E1000_REGS_LEN 32	/* overestimate */
 	return E1000_REGS_LEN * sizeof(u32);
 }
 
@@ -433,22 +433,22 @@ static void e1000_get_regs(struct net_device *netdev,
 	regs->version = (1 << 24) | (adapter->pdev->revision << 16) |
 	    adapter->pdev->device;
 
-	regs_buff[0]  = er32(CTRL);
-	regs_buff[1]  = er32(STATUS);
+	regs_buff[0] = er32(CTRL);
+	regs_buff[1] = er32(STATUS);
 
-	regs_buff[2]  = er32(RCTL);
-	regs_buff[3]  = er32(RDLEN(0));
-	regs_buff[4]  = er32(RDH(0));
-	regs_buff[5]  = er32(RDT(0));
-	regs_buff[6]  = er32(RDTR);
+	regs_buff[2] = er32(RCTL);
+	regs_buff[3] = er32(RDLEN(0));
+	regs_buff[4] = er32(RDH(0));
+	regs_buff[5] = er32(RDT(0));
+	regs_buff[6] = er32(RDTR);
 
-	regs_buff[7]  = er32(TCTL);
-	regs_buff[8]  = er32(TDLEN(0));
-	regs_buff[9]  = er32(TDH(0));
+	regs_buff[7] = er32(TCTL);
+	regs_buff[8] = er32(TDLEN(0));
+	regs_buff[9] = er32(TDH(0));
 	regs_buff[10] = er32(TDT(0));
 	regs_buff[11] = er32(TIDV);
 
-	regs_buff[12] = adapter->hw.phy.type;  /* PHY type (IGP=1, M88=0) */
+	regs_buff[12] = adapter->hw.phy.type;	/* PHY type (IGP=1, M88=0) */
 
 	/* ethtool doesn't use anything past this point, so all this
 	 * code is likely legacy junk for apps that may or may not exist
@@ -1379,7 +1379,7 @@ static int e1000_integrated_phy_loopback(struct e1000_adapter *adapter)
 
 	if (hw->phy.media_type == e1000_media_type_copper &&
 	    hw->phy.type == e1000_phy_m88) {
-		ctrl_reg |= E1000_CTRL_ILOS; /* Invert Loss of Signal */
+		ctrl_reg |= E1000_CTRL_ILOS;	/* Invert Loss of Signal */
 	} else {
 		/* Set the ILOS bit on the fiber Nic if half duplex link is
 		 * detected.
@@ -1613,7 +1613,7 @@ static int e1000_run_loopback_test(struct e1000_adapter *adapter)
 		ew32(TDT(0), k);
 		e1e_flush();
 		msleep(200);
-		time = jiffies; /* set the start time for the receive */
+		time = jiffies;	/* set the start time for the receive */
 		good_cnt = 0;
 		/* receive the sent packets */
 		do {
@@ -1636,11 +1636,11 @@ static int e1000_run_loopback_test(struct e1000_adapter *adapter)
 			 */
 		} while ((good_cnt < 64) && !time_after(jiffies, time + 20));
 		if (good_cnt != 64) {
-			ret_val = 13; /* ret_val is the same as mis-compare */
+			ret_val = 13;	/* ret_val is the same as mis-compare */
 			break;
 		}
 		if (jiffies >= (time + 20)) {
-			ret_val = 14; /* error code for time out error */
+			ret_val = 14;	/* error code for time out error */
 			break;
 		}
 	}

drivers/net/ethernet/intel/e1000e/hw.h

@@ -402,13 +402,13 @@ struct e1000_phy_stats {
 
 struct e1000_host_mng_dhcp_cookie {
 	u32 signature;
-	u8  status;
-	u8  reserved0;
+	u8 status;
+	u8 reserved0;
 	u16 vlan_id;
 	u32 reserved1;
 	u16 reserved2;
-	u8  reserved3;
-	u8  checksum;
+	u8 reserved3;
+	u8 checksum;
 };
 
 /* Host Interface "Rev 1" */
@@ -427,8 +427,8 @@ struct e1000_host_command_info {
 
 /* Host Interface "Rev 2" */
 struct e1000_host_mng_command_header {
-	u8  command_id;
-	u8  checksum;
+	u8 command_id;
+	u8 checksum;
 	u16 reserved1;
 	u16 reserved2;
 	u16 command_length;
@@ -549,7 +549,7 @@ struct e1000_mac_info {
 	u32 mta_shadow[MAX_MTA_REG];
 	u16 rar_entry_count;
 
-	u8  forced_speed_duplex;
+	u8 forced_speed_duplex;
 
 	bool adaptive_ifs;
 	bool has_fwsm;
@@ -577,7 +577,7 @@ struct e1000_phy_info {
 
 	u32 addr;
 	u32 id;
-	u32 reset_delay_us; /* in usec */
+	u32 reset_delay_us;	/* in usec */
 	u32 revision;
 
 	enum e1000_media_type media_type;
@@ -636,11 +636,11 @@ struct e1000_dev_spec_82571 {
 };
 
 struct e1000_dev_spec_80003es2lan {
-	bool  mdic_wa_enable;
+	bool mdic_wa_enable;
 };
 
 struct e1000_shadow_ram {
-	u16  value;
+	u16 value;
 	bool modified;
 };
 
@@ -660,17 +660,17 @@ struct e1000_hw {
 	void __iomem *hw_addr;
 	void __iomem *flash_address;
 
-	struct e1000_mac_info  mac;
-	struct e1000_fc_info   fc;
-	struct e1000_phy_info  phy;
-	struct e1000_nvm_info  nvm;
-	struct e1000_bus_info  bus;
+	struct e1000_mac_info mac;
+	struct e1000_fc_info fc;
+	struct e1000_phy_info phy;
+	struct e1000_nvm_info nvm;
+	struct e1000_bus_info bus;
 	struct e1000_host_mng_dhcp_cookie mng_cookie;
 
 	union {
-		struct e1000_dev_spec_82571	e82571;
+		struct e1000_dev_spec_82571 e82571;
 		struct e1000_dev_spec_80003es2lan e80003es2lan;
-		struct e1000_dev_spec_ich8lan	ich8lan;
+		struct e1000_dev_spec_ich8lan ich8lan;
 	} dev_spec;
 };
 

drivers/net/ethernet/intel/e1000e/ich8lan.c

@@ -101,12 +101,12 @@ union ich8_hws_flash_regacc {
 /* ICH Flash Protected Region */
 union ich8_flash_protected_range {
 	struct ich8_pr {
-		u32 base:13;     /* 0:12 Protected Range Base */
-		u32 reserved1:2; /* 13:14 Reserved */
-		u32 rpe:1;       /* 15 Read Protection Enable */
-		u32 limit:13;    /* 16:28 Protected Range Limit */
-		u32 reserved2:2; /* 29:30 Reserved */
-		u32 wpe:1;       /* 31 Write Protection Enable */
+		u32 base:13;	/* 0:12 Protected Range Base */
+		u32 reserved1:2;	/* 13:14 Reserved */
+		u32 rpe:1;	/* 15 Read Protection Enable */
+		u32 limit:13;	/* 16:28 Protected Range Limit */
+		u32 reserved2:2;	/* 29:30 Reserved */
+		u32 wpe:1;	/* 31 Write Protection Enable */
 	} range;
 	u32 regval;
 };
@@ -362,21 +362,21 @@ static s32 e1000_init_phy_params_pchlan(struct e1000_hw *hw)
 	struct e1000_phy_info *phy = &hw->phy;
 	s32 ret_val;
 
-	phy->addr                     = 1;
-	phy->reset_delay_us           = 100;
-
-	phy->ops.set_page             = e1000_set_page_igp;
-	phy->ops.read_reg             = e1000_read_phy_reg_hv;
-	phy->ops.read_reg_locked      = e1000_read_phy_reg_hv_locked;
-	phy->ops.read_reg_page        = e1000_read_phy_reg_page_hv;
-	phy->ops.set_d0_lplu_state    = e1000_set_lplu_state_pchlan;
-	phy->ops.set_d3_lplu_state    = e1000_set_lplu_state_pchlan;
-	phy->ops.write_reg            = e1000_write_phy_reg_hv;
-	phy->ops.write_reg_locked     = e1000_write_phy_reg_hv_locked;
-	phy->ops.write_reg_page       = e1000_write_phy_reg_page_hv;
-	phy->ops.power_up             = e1000_power_up_phy_copper;
-	phy->ops.power_down           = e1000_power_down_phy_copper_ich8lan;
-	phy->autoneg_mask             = AUTONEG_ADVERTISE_SPEED_DEFAULT;
+	phy->addr = 1;
+	phy->reset_delay_us = 100;
+
+	phy->ops.set_page = e1000_set_page_igp;
+	phy->ops.read_reg = e1000_read_phy_reg_hv;
+	phy->ops.read_reg_locked = e1000_read_phy_reg_hv_locked;
+	phy->ops.read_reg_page = e1000_read_phy_reg_page_hv;
+	phy->ops.set_d0_lplu_state = e1000_set_lplu_state_pchlan;
+	phy->ops.set_d3_lplu_state = e1000_set_lplu_state_pchlan;
+	phy->ops.write_reg = e1000_write_phy_reg_hv;
+	phy->ops.write_reg_locked = e1000_write_phy_reg_hv_locked;
+	phy->ops.write_reg_page = e1000_write_phy_reg_page_hv;
+	phy->ops.power_up = e1000_power_up_phy_copper;
+	phy->ops.power_down = e1000_power_down_phy_copper_ich8lan;
+	phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT;
 
 	phy->id = e1000_phy_unknown;
 
@@ -445,11 +445,11 @@ static s32 e1000_init_phy_params_ich8lan(struct e1000_hw *hw)
 	s32 ret_val;
 	u16 i = 0;
 
-	phy->addr			= 1;
-	phy->reset_delay_us		= 100;
+	phy->addr = 1;
+	phy->reset_delay_us = 100;
 
-	phy->ops.power_up               = e1000_power_up_phy_copper;
-	phy->ops.power_down             = e1000_power_down_phy_copper_ich8lan;
+	phy->ops.power_up = e1000_power_up_phy_copper;
+	phy->ops.power_down = e1000_power_down_phy_copper_ich8lan;
 
 	/* We may need to do this twice - once for IGP and if that fails,
 	 * we'll set BM func pointers and try again
@@ -457,7 +457,7 @@ static s32 e1000_init_phy_params_ich8lan(struct e1000_hw *hw)
 	ret_val = e1000e_determine_phy_address(hw);
 	if (ret_val) {
 		phy->ops.write_reg = e1000e_write_phy_reg_bm;
-		phy->ops.read_reg  = e1000e_read_phy_reg_bm;
+		phy->ops.read_reg = e1000e_read_phy_reg_bm;
 		ret_val = e1000e_determine_phy_address(hw);
 		if (ret_val) {
 			e_dbg("Cannot determine PHY addr. Erroring out\n");
@@ -560,7 +560,7 @@ static s32 e1000_init_nvm_params_ich8lan(struct e1000_hw *hw)
 	/* Clear shadow ram */
 	for (i = 0; i < nvm->word_size; i++) {
 		dev_spec->shadow_ram[i].modified = false;
-		dev_spec->shadow_ram[i].value    = 0xFFFF;
+		dev_spec->shadow_ram[i].value = 0xFFFF;
 	}
 
 	return 0;
@@ -1012,7 +1012,7 @@ static s32 e1000_check_for_copper_link_ich8lan(struct e1000_hw *hw)
 	hw->dev_spec.ich8lan.eee_lp_ability = 0;
 
 	if (!link)
-		return 0; /* No link detected */
+		return 0;	/* No link detected */
 
 	mac->get_link_status = false;
 
@@ -2816,7 +2816,7 @@ static s32 e1000_read_flash_data_ich8lan(struct e1000_hw *hw, u32 offset,
 	s32 ret_val = -E1000_ERR_NVM;
 	u8 count = 0;
 
-	if (size < 1  || size > 2 || offset > ICH_FLASH_LINEAR_ADDR_MASK)
+	if (size < 1 || size > 2 || offset > ICH_FLASH_LINEAR_ADDR_MASK)
 		return -E1000_ERR_NVM;
 
 	flash_linear_addr = ((ICH_FLASH_LINEAR_ADDR_MASK & offset) +
@@ -2939,7 +2939,7 @@ static s32 e1000_update_nvm_checksum_ich8lan(struct e1000_hw *hw)
 	 * write to bank 0 etc.  We also need to erase the segment that
 	 * is going to be written
 	 */
-	ret_val =  e1000_valid_nvm_bank_detect_ich8lan(hw, &bank);
+	ret_val = e1000_valid_nvm_bank_detect_ich8lan(hw, &bank);
 	if (ret_val) {
 		e_dbg("Could not detect valid bank, assuming bank 0\n");
 		bank = 0;
@@ -4073,7 +4073,7 @@ void e1000e_igp3_phy_powerdown_workaround_ich8lan(struct e1000_hw *hw)
 {
 	u32 reg;
 	u16 data;
-	u8  retry = 0;
+	u8 retry = 0;
 
 	if (hw->phy.type != e1000_phy_igp_3)
 		return;

drivers/net/ethernet/intel/e1000e/netdev.c

@@ -1196,7 +1196,7 @@ static bool e1000_clean_tx_irq(struct e1000_ring *tx_ring)
 	while ((eop_desc->upper.data & cpu_to_le32(E1000_TXD_STAT_DD)) &&
 	       (count < tx_ring->count)) {
 		bool cleaned = false;
-		rmb(); /* read buffer_info after eop_desc */
+		rmb();		/* read buffer_info after eop_desc */
 		for (; !cleaned; count++) {
 			tx_desc = E1000_TX_DESC(*tx_ring, i);
 			buffer_info = &tx_ring->buffer_info[i];
@@ -1385,7 +1385,7 @@ static bool e1000_clean_rx_irq_ps(struct e1000_ring *rx_ring, int *work_done,
 
 				skb_put(skb, l1);
 				goto copydone;
-			} /* if */
+			}	/* if */
 		}
 
 		for (j = 0; j < PS_PAGE_BUFFERS; j++) {
@@ -1800,7 +1800,7 @@ static irqreturn_t e1000_intr(int __always_unused irq, void *data)
 	u32 rctl, icr = er32(ICR);
 
 	if (!icr || test_bit(__E1000_DOWN, &adapter->state))
-		return IRQ_NONE;  /* Not our interrupt */
+		return IRQ_NONE;	/* Not our interrupt */
 
 	/* IMS will not auto-mask if INT_ASSERTED is not set, and if it is
 	 * not set, then the adapter didn't send an interrupt
@@ -2487,7 +2487,7 @@ static unsigned int e1000_update_itr(u16 itr_setting, int packets, int bytes)
 		else if ((packets < 5) && (bytes > 512))
 			retval = low_latency;
 		break;
-	case low_latency:  /* 50 usec aka 20000 ints/s */
+	case low_latency:	/* 50 usec aka 20000 ints/s */
 		if (bytes > 10000) {
 			/* this if handles the TSO accounting */
 			if (bytes / packets > 8000)
@@ -2502,7 +2502,7 @@ static unsigned int e1000_update_itr(u16 itr_setting, int packets, int bytes)
 			retval = lowest_latency;
 		}
 		break;
-	case bulk_latency: /* 250 usec aka 4000 ints/s */
+	case bulk_latency:	/* 250 usec aka 4000 ints/s */
 		if (bytes > 25000) {
 			if (packets > 35)
 				retval = low_latency;
@@ -2554,7 +2554,7 @@ static void e1000_set_itr(struct e1000_adapter *adapter)
 		new_itr = 70000;
 		break;
 	case low_latency:
-		new_itr = 20000; /* aka hwitr = ~200 */
+		new_itr = 20000;	/* aka hwitr = ~200 */
 		break;
 	case bulk_latency:
 		new_itr = 4000;
@@ -2673,7 +2673,7 @@ static int e1000e_poll(struct napi_struct *napi, int weight)
 }
 
 static int e1000_vlan_rx_add_vid(struct net_device *netdev,
-				 __be16 proto, u16 vid)
+				 __always_unused __be16 proto, u16 vid)
 {
 	struct e1000_adapter *adapter = netdev_priv(netdev);
 	struct e1000_hw *hw = &adapter->hw;
@@ -2699,7 +2699,7 @@ static int e1000_vlan_rx_add_vid(struct net_device *netdev,
 }
 
 static int e1000_vlan_rx_kill_vid(struct net_device *netdev,
-				  __be16 proto, u16 vid)
+				  __always_unused __be16 proto, u16 vid)
 {
 	struct e1000_adapter *adapter = netdev_priv(netdev);
 	struct e1000_hw *hw = &adapter->hw;
@@ -3104,13 +3104,13 @@ static void e1000_setup_rctl(struct e1000_adapter *adapter)
 		/* UPE and MPE will be handled by normal PROMISC logic
 		 * in e1000e_set_rx_mode
 		 */
-		rctl |= (E1000_RCTL_SBP | /* Receive bad packets */
-			 E1000_RCTL_BAM | /* RX All Bcast Pkts */
-			 E1000_RCTL_PMCF); /* RX All MAC Ctrl Pkts */
+		rctl |= (E1000_RCTL_SBP |	/* Receive bad packets */
+			 E1000_RCTL_BAM |	/* RX All Bcast Pkts */
+			 E1000_RCTL_PMCF);	/* RX All MAC Ctrl Pkts */
 
-		rctl &= ~(E1000_RCTL_VFE | /* Disable VLAN filter */
-			  E1000_RCTL_DPF | /* Allow filtered pause */
-			  E1000_RCTL_CFIEN); /* Dis VLAN CFIEN Filter */
+		rctl &= ~(E1000_RCTL_VFE |	/* Disable VLAN filter */
+			  E1000_RCTL_DPF |	/* Allow filtered pause */
+			  E1000_RCTL_CFIEN);	/* Dis VLAN CFIEN Filter */
 		/* Do not mess with E1000_CTRL_VME, it affects transmit as well,
 		 * and that breaks VLANs.
 		 */
@@ -3799,7 +3799,7 @@ void e1000e_reset(struct e1000_adapter *adapter)
 		hwm = min(((pba << 10) * 9 / 10),
 			  ((pba << 10) - adapter->max_frame_size));
 
-		fc->high_water = hwm & E1000_FCRTH_RTH; /* 8-byte granularity */
+		fc->high_water = hwm & E1000_FCRTH_RTH;	/* 8-byte granularity */
 		fc->low_water = fc->high_water - 8;
 		break;
 	case e1000_pchlan:
@@ -3808,10 +3808,10 @@ void e1000e_reset(struct e1000_adapter *adapter)
 		 */
 		if (adapter->netdev->mtu > ETH_DATA_LEN) {
 			fc->high_water = 0x3500;
-			fc->low_water  = 0x1500;
+			fc->low_water = 0x1500;
 		} else {
 			fc->high_water = 0x5000;
-			fc->low_water  = 0x3000;
+			fc->low_water = 0x3000;
 		}
 		fc->refresh_time = 0x1000;
 		break;
@@ -4581,7 +4581,7 @@ static void e1000e_update_stats(struct e1000_adapter *adapter)
 	adapter->stats.crcerrs += er32(CRCERRS);
 	adapter->stats.gprc += er32(GPRC);
 	adapter->stats.gorc += er32(GORCL);
-	er32(GORCH); /* Clear gorc */
+	er32(GORCH);		/* Clear gorc */
 	adapter->stats.bprc += er32(BPRC);
 	adapter->stats.mprc += er32(MPRC);
 	adapter->stats.roc += er32(ROC);
@@ -4614,7 +4614,7 @@ static void e1000e_update_stats(struct e1000_adapter *adapter)
 	adapter->stats.xofftxc += er32(XOFFTXC);
 	adapter->stats.gptc += er32(GPTC);
 	adapter->stats.gotc += er32(GOTCL);
-	er32(GOTCH); /* Clear gotc */
+	er32(GOTCH);		/* Clear gotc */
 	adapter->stats.rnbc += er32(RNBC);
 	adapter->stats.ruc += er32(RUC);
 
@@ -5106,13 +5106,13 @@ static int e1000_tso(struct e1000_ring *tx_ring, struct sk_buff *skb)
 	context_desc = E1000_CONTEXT_DESC(*tx_ring, i);
 	buffer_info = &tx_ring->buffer_info[i];
 
-	context_desc->lower_setup.ip_fields.ipcss  = ipcss;
-	context_desc->lower_setup.ip_fields.ipcso  = ipcso;
-	context_desc->lower_setup.ip_fields.ipcse  = cpu_to_le16(ipcse);
+	context_desc->lower_setup.ip_fields.ipcss = ipcss;
+	context_desc->lower_setup.ip_fields.ipcso = ipcso;
+	context_desc->lower_setup.ip_fields.ipcse = cpu_to_le16(ipcse);
 	context_desc->upper_setup.tcp_fields.tucss = tucss;
 	context_desc->upper_setup.tcp_fields.tucso = tucso;
 	context_desc->upper_setup.tcp_fields.tucse = 0;
-	context_desc->tcp_seg_setup.fields.mss     = cpu_to_le16(mss);
+	context_desc->tcp_seg_setup.fields.mss = cpu_to_le16(mss);
 	context_desc->tcp_seg_setup.fields.hdr_len = hdr_len;
 	context_desc->cmd_and_length = cpu_to_le32(cmd_length);
 
@@ -5363,7 +5363,7 @@ static void e1000_tx_queue(struct e1000_ring *tx_ring, int tx_flags, int count)
 static int e1000_transfer_dhcp_info(struct e1000_adapter *adapter,
 				    struct sk_buff *skb)
 {
-	struct e1000_hw *hw =  &adapter->hw;
+	struct e1000_hw *hw = &adapter->hw;
 	u16 length, offset;
 
 	if (vlan_tx_tag_present(skb) &&
@@ -6259,7 +6259,7 @@ static void e1000_netpoll(struct net_device *netdev)
 		e1000_intr_msi(adapter->pdev->irq, netdev);
 		enable_irq(adapter->pdev->irq);
 		break;
-	default: /* E1000E_INT_MODE_LEGACY */
+	default:		/* E1000E_INT_MODE_LEGACY */
 		disable_irq(adapter->pdev->irq);
 		e1000_intr(adapter->pdev->irq, netdev);
 		enable_irq(adapter->pdev->irq);
@@ -6589,9 +6589,9 @@ static int e1000_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 		adapter->eee_advert = MDIO_EEE_100TX | MDIO_EEE_1000T;
 
 	/* construct the net_device struct */
-	netdev->netdev_ops		= &e1000e_netdev_ops;
+	netdev->netdev_ops = &e1000e_netdev_ops;
 	e1000e_set_ethtool_ops(netdev);
-	netdev->watchdog_timeo		= 5 * HZ;
+	netdev->watchdog_timeo = 5 * HZ;
 	netif_napi_add(netdev, &adapter->napi, e1000e_poll, 64);
 	strlcpy(netdev->name, pci_name(pdev), sizeof(netdev->name));
 
@@ -7034,7 +7034,6 @@ static void __exit e1000_exit_module(void)
 }
 module_exit(e1000_exit_module);
 
-
 MODULE_AUTHOR("Intel Corporation, <linux.nics@intel.com>");
 MODULE_DESCRIPTION("Intel(R) PRO/1000 Network Driver");
 MODULE_LICENSE("GPL");

drivers/net/ethernet/intel/e1000e/nvm.c

@@ -117,7 +117,6 @@ static u16 e1000_shift_in_eec_bits(struct e1000_hw *hw, u16 count)
 	u16 data;
 
 	eecd = er32(EECD);
-
 	eecd &= ~(E1000_EECD_DO | E1000_EECD_DI);
 	data = 0;
 

drivers/net/ethernet/intel/e1000e/phy.c

@@ -1583,13 +1583,13 @@ s32 e1000e_check_downshift(struct e1000_hw *hw)
 	case e1000_phy_gg82563:
 	case e1000_phy_bm:
 	case e1000_phy_82578:
-		offset	= M88E1000_PHY_SPEC_STATUS;
-		mask	= M88E1000_PSSR_DOWNSHIFT;
+		offset = M88E1000_PHY_SPEC_STATUS;
+		mask = M88E1000_PSSR_DOWNSHIFT;
 		break;
 	case e1000_phy_igp_2:
 	case e1000_phy_igp_3:
-		offset	= IGP01E1000_PHY_LINK_HEALTH;
-		mask	= IGP01E1000_PLHR_SS_DOWNGRADE;
+		offset = IGP01E1000_PHY_LINK_HEALTH;
+		mask = IGP01E1000_PLHR_SS_DOWNGRADE;
 		break;
 	default:
 		/* speed downshift not supported */
@@ -1653,14 +1653,14 @@ s32 e1000_check_polarity_igp(struct e1000_hw *hw)
 
 	if ((data & IGP01E1000_PSSR_SPEED_MASK) ==
 	    IGP01E1000_PSSR_SPEED_1000MBPS) {
-		offset	= IGP01E1000_PHY_PCS_INIT_REG;
-		mask	= IGP01E1000_PHY_POLARITY_MASK;
+		offset = IGP01E1000_PHY_PCS_INIT_REG;
+		mask = IGP01E1000_PHY_POLARITY_MASK;
 	} else {
 		/* This really only applies to 10Mbps since
 		 * there is no polarity for 100Mbps (always 0).
 		 */
-		offset	= IGP01E1000_PHY_PORT_STATUS;
-		mask	= IGP01E1000_PSSR_POLARITY_REVERSED;
+		offset = IGP01E1000_PHY_PORT_STATUS;
+		mask = IGP01E1000_PSSR_POLARITY_REVERSED;
 	}
 
 	ret_val = e1e_rphy(hw, offset, &data);
@@ -1900,7 +1900,7 @@ s32 e1000e_get_cable_length_igp_2(struct e1000_hw *hw)
 s32 e1000e_get_phy_info_m88(struct e1000_hw *hw)
 {
 	struct e1000_phy_info *phy = &hw->phy;
-	s32  ret_val;
+	s32 ret_val;
 	u16 phy_data;
 	bool link;
 
@@ -2253,7 +2253,7 @@ enum e1000_phy_type e1000e_get_phy_type_from_id(u32 phy_id)
 	case M88E1011_I_PHY_ID:
 		phy_type = e1000_phy_m88;
 		break;
-	case IGP01E1000_I_PHY_ID: /* IGP 1 & 2 share this */
+	case IGP01E1000_I_PHY_ID:	/* IGP 1 & 2 share this */
 		phy_type = e1000_phy_igp_2;
 		break;
 	case GG82563_E_PHY_ID:
@@ -2317,7 +2317,7 @@ s32 e1000e_determine_phy_address(struct e1000_hw *hw)
 			/* If phy_type is valid, break - we found our
 			 * PHY address
 			 */
-			if (phy_type  != e1000_phy_unknown)
+			if (phy_type != e1000_phy_unknown)
 				return 0;
 
 			usleep_range(1000, 2000);

drivers/net/ethernet/intel/igb/e1000_82575.c

@@ -401,12 +401,82 @@ static s32 igb_init_mac_params_82575(struct e1000_hw *hw)
 	return 0;
 }
 
+/**
+ *  igb_set_sfp_media_type_82575 - derives SFP module media type.
+ *  @hw: pointer to the HW structure
+ *
+ *  The media type is chosen based on SFP module.
+ *  compatibility flags retrieved from SFP ID EEPROM.
+ **/
+static s32 igb_set_sfp_media_type_82575(struct e1000_hw *hw)
+{
+	s32 ret_val = E1000_ERR_CONFIG;
+	u32 ctrl_ext = 0;
+	struct e1000_dev_spec_82575 *dev_spec = &hw->dev_spec._82575;
+	struct e1000_sfp_flags *eth_flags = &dev_spec->eth_flags;
+	u8 tranceiver_type = 0;
+	s32 timeout = 3;
+
+	/* Turn I2C interface ON and power on sfp cage */
+	ctrl_ext = rd32(E1000_CTRL_EXT);
+	ctrl_ext &= ~E1000_CTRL_EXT_SDP3_DATA;
+	wr32(E1000_CTRL_EXT, ctrl_ext | E1000_CTRL_I2C_ENA);
+
+	wrfl();
+
+	/* Read SFP module data */
+	while (timeout) {
+		ret_val = igb_read_sfp_data_byte(hw,
+			E1000_I2CCMD_SFP_DATA_ADDR(E1000_SFF_IDENTIFIER_OFFSET),
+			&tranceiver_type);
+		if (ret_val == 0)
+			break;
+		msleep(100);
+		timeout--;
+	}
+	if (ret_val != 0)
+		goto out;
+
+	ret_val = igb_read_sfp_data_byte(hw,
+			E1000_I2CCMD_SFP_DATA_ADDR(E1000_SFF_ETH_FLAGS_OFFSET),
+			(u8 *)eth_flags);
+	if (ret_val != 0)
+		goto out;
+
+	/* Check if there is some SFP module plugged and powered */
+	if ((tranceiver_type == E1000_SFF_IDENTIFIER_SFP) ||
+	    (tranceiver_type == E1000_SFF_IDENTIFIER_SFF)) {
+		dev_spec->module_plugged = true;
+		if (eth_flags->e1000_base_lx || eth_flags->e1000_base_sx) {
+			hw->phy.media_type = e1000_media_type_internal_serdes;
+		} else if (eth_flags->e100_base_fx) {
+			dev_spec->sgmii_active = true;
+			hw->phy.media_type = e1000_media_type_internal_serdes;
+		} else if (eth_flags->e1000_base_t) {
+			dev_spec->sgmii_active = true;
+			hw->phy.media_type = e1000_media_type_copper;
+		} else {
+			hw->phy.media_type = e1000_media_type_unknown;
+			hw_dbg("PHY module has not been recognized\n");
+			goto out;
+		}
+	} else {
+		hw->phy.media_type = e1000_media_type_unknown;
+	}
+	ret_val = 0;
+out:
+	/* Restore I2C interface setting */
+	wr32(E1000_CTRL_EXT, ctrl_ext);
+	return ret_val;
+}
+
 static s32 igb_get_invariants_82575(struct e1000_hw *hw)
 {
 	struct e1000_mac_info *mac = &hw->mac;
 	struct e1000_dev_spec_82575 * dev_spec = &hw->dev_spec._82575;
 	s32 ret_val;
 	u32 ctrl_ext = 0;
+	u32 link_mode = 0;
 
 	switch (hw->device_id) {
 	case E1000_DEV_ID_82575EB_COPPER:
@@ -470,15 +540,55 @@ static s32 igb_get_invariants_82575(struct e1000_hw *hw)
 	 */
 	hw->phy.media_type = e1000_media_type_copper;
 	dev_spec->sgmii_active = false;
+	dev_spec->module_plugged = false;
 
 	ctrl_ext = rd32(E1000_CTRL_EXT);
-	switch (ctrl_ext & E1000_CTRL_EXT_LINK_MODE_MASK) {
-	case E1000_CTRL_EXT_LINK_MODE_SGMII:
-		dev_spec->sgmii_active = true;
-		break;
+
+	link_mode = ctrl_ext & E1000_CTRL_EXT_LINK_MODE_MASK;
+	switch (link_mode) {
 	case E1000_CTRL_EXT_LINK_MODE_1000BASE_KX:
-	case E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES:
 		hw->phy.media_type = e1000_media_type_internal_serdes;
+		break;
+	case E1000_CTRL_EXT_LINK_MODE_SGMII:
+		/* Get phy control interface type set (MDIO vs. I2C)*/
+		if (igb_sgmii_uses_mdio_82575(hw)) {
+			hw->phy.media_type = e1000_media_type_copper;
+			dev_spec->sgmii_active = true;
+			break;
+		}
+		/* fall through for I2C based SGMII */
+	case E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES:
+		/* read media type from SFP EEPROM */
+		ret_val = igb_set_sfp_media_type_82575(hw);
+		if ((ret_val != 0) ||
+		    (hw->phy.media_type == e1000_media_type_unknown)) {
+			/* If media type was not identified then return media
+			 * type defined by the CTRL_EXT settings.
+			 */
+			hw->phy.media_type = e1000_media_type_internal_serdes;
+
+			if (link_mode == E1000_CTRL_EXT_LINK_MODE_SGMII) {
+				hw->phy.media_type = e1000_media_type_copper;
+				dev_spec->sgmii_active = true;
+			}
+
+			break;
+		}
+
+		/* do not change link mode for 100BaseFX */
+		if (dev_spec->eth_flags.e100_base_fx)
+			break;
+
+		/* change current link mode setting */
+		ctrl_ext &= ~E1000_CTRL_EXT_LINK_MODE_MASK;
+
+		if (hw->phy.media_type == e1000_media_type_copper)
+			ctrl_ext |= E1000_CTRL_EXT_LINK_MODE_SGMII;
+		else
+			ctrl_ext |= E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES;
+
+		wr32(E1000_CTRL_EXT, ctrl_ext);
+
 		break;
 	default:
 		break;

drivers/net/ethernet/intel/igb/e1000_defines.h

@@ -61,20 +61,22 @@
 /* Clear Interrupt timers after IMS clear */
 /* packet buffer parity error detection enabled */
 /* descriptor FIFO parity error detection enable */
-#define E1000_CTRL_EXT_PBA_CLR        0x80000000 /* PBA Clear */
-#define E1000_I2CCMD_REG_ADDR_SHIFT   16
-#define E1000_I2CCMD_PHY_ADDR_SHIFT   24
-#define E1000_I2CCMD_OPCODE_READ      0x08000000
-#define E1000_I2CCMD_OPCODE_WRITE     0x00000000
-#define E1000_I2CCMD_READY            0x20000000
-#define E1000_I2CCMD_ERROR            0x80000000
-#define E1000_MAX_SGMII_PHY_REG_ADDR  255
-#define E1000_I2CCMD_PHY_TIMEOUT      200
-#define E1000_IVAR_VALID              0x80
-#define E1000_GPIE_NSICR              0x00000001
-#define E1000_GPIE_MSIX_MODE          0x00000010
-#define E1000_GPIE_EIAME              0x40000000
-#define E1000_GPIE_PBA                0x80000000
+#define E1000_CTRL_EXT_PBA_CLR		0x80000000 /* PBA Clear */
+#define E1000_I2CCMD_REG_ADDR_SHIFT	16
+#define E1000_I2CCMD_PHY_ADDR_SHIFT	24
+#define E1000_I2CCMD_OPCODE_READ	0x08000000
+#define E1000_I2CCMD_OPCODE_WRITE	0x00000000
+#define E1000_I2CCMD_READY		0x20000000
+#define E1000_I2CCMD_ERROR		0x80000000
+#define E1000_I2CCMD_SFP_DATA_ADDR(a)	(0x0000 + (a))
+#define E1000_I2CCMD_SFP_DIAG_ADDR(a)	(0x0100 + (a))
+#define E1000_MAX_SGMII_PHY_REG_ADDR	255
+#define E1000_I2CCMD_PHY_TIMEOUT	200
+#define E1000_IVAR_VALID		0x80
+#define E1000_GPIE_NSICR		0x00000001
+#define E1000_GPIE_MSIX_MODE		0x00000010
+#define E1000_GPIE_EIAME		0x40000000
+#define E1000_GPIE_PBA			0x80000000
 
 /* Receive Descriptor bit definitions */
 #define E1000_RXD_STAT_DD       0x01    /* Descriptor Done */
@@ -270,8 +272,10 @@
 #define AUTONEG_ADVERTISE_SPEED_DEFAULT   E1000_ALL_SPEED_DUPLEX
 
 /* LED Control */
-#define E1000_LEDCTL_LED0_MODE_SHIFT      0
-#define E1000_LEDCTL_LED0_BLINK           0x00000080
+#define E1000_LEDCTL_LED0_MODE_SHIFT	0
+#define E1000_LEDCTL_LED0_BLINK		0x00000080
+#define E1000_LEDCTL_LED0_MODE_MASK	0x0000000F
+#define E1000_LEDCTL_LED0_IVRT		0x00000040
 
 #define E1000_LEDCTL_MODE_LED_ON        0xE
 #define E1000_LEDCTL_MODE_LED_OFF       0xF

drivers/net/ethernet/intel/igb/e1000_hw.h

@@ -528,6 +528,8 @@ struct e1000_dev_spec_82575 {
 	bool global_device_reset;
 	bool eee_disable;
 	bool clear_semaphore_once;
+	struct e1000_sfp_flags eth_flags;
+	bool module_plugged;
 };
 
 struct e1000_hw {

drivers/net/ethernet/intel/igb/e1000_i210.h

@@ -82,11 +82,11 @@ enum E1000_INVM_STRUCTURE_TYPE {
 #define E1000_INVM_MAJOR_SHIFT		4
 
 #define ID_LED_DEFAULT_I210		((ID_LED_OFF1_ON2  << 8) | \
-					 (ID_LED_OFF1_OFF2 <<  4) | \
-					 (ID_LED_DEF1_DEF2))
+					 (ID_LED_DEF1_DEF2 <<  4) | \
+					 (ID_LED_OFF1_OFF2))
 #define ID_LED_DEFAULT_I210_SERDES	((ID_LED_DEF1_DEF2 << 8) | \
 					 (ID_LED_DEF1_DEF2 <<  4) | \
-					 (ID_LED_DEF1_DEF2))
+					 (ID_LED_OFF1_ON2))
 
 /* NVM offset defaults for i211 device */
 #define NVM_INIT_CTRL_2_DEFAULT_I211	0X7243

drivers/net/ethernet/intel/igb/e1000_mac.c

@@ -1332,7 +1332,13 @@ s32 igb_id_led_init(struct e1000_hw *hw)
 	u16 data, i, temp;
 	const u16 led_mask = 0x0F;
 
-	ret_val = igb_valid_led_default(hw, &data);
+	/* i210 and i211 devices have different LED mechanism */
+	if ((hw->mac.type == e1000_i210) ||
+	    (hw->mac.type == e1000_i211))
+		ret_val = igb_valid_led_default_i210(hw, &data);
+	else
+		ret_val = igb_valid_led_default(hw, &data);
+
 	if (ret_val)
 		goto out;
 
@@ -1406,15 +1412,34 @@ s32 igb_blink_led(struct e1000_hw *hw)
 	u32 ledctl_blink = 0;
 	u32 i;
 
-	/* set the blink bit for each LED that's "on" (0x0E)
-	 * in ledctl_mode2
-	 */
-	ledctl_blink = hw->mac.ledctl_mode2;
-	for (i = 0; i < 4; i++)
-		if (((hw->mac.ledctl_mode2 >> (i * 8)) & 0xFF) ==
-		    E1000_LEDCTL_MODE_LED_ON)
-			ledctl_blink |= (E1000_LEDCTL_LED0_BLINK <<
-					 (i * 8));
+	if (hw->phy.media_type == e1000_media_type_fiber) {
+		/* always blink LED0 for PCI-E fiber */
+		ledctl_blink = E1000_LEDCTL_LED0_BLINK |
+		     (E1000_LEDCTL_MODE_LED_ON << E1000_LEDCTL_LED0_MODE_SHIFT);
+	} else {
+		/* Set the blink bit for each LED that's "on" (0x0E)
+		 * (or "off" if inverted) in ledctl_mode2.  The blink
+		 * logic in hardware only works when mode is set to "on"
+		 * so it must be changed accordingly when the mode is
+		 * "off" and inverted.
+		 */
+		ledctl_blink = hw->mac.ledctl_mode2;
+		for (i = 0; i < 32; i += 8) {
+			u32 mode = (hw->mac.ledctl_mode2 >> i) &
+			    E1000_LEDCTL_LED0_MODE_MASK;
+			u32 led_default = hw->mac.ledctl_default >> i;
+
+			if ((!(led_default & E1000_LEDCTL_LED0_IVRT) &&
+			     (mode == E1000_LEDCTL_MODE_LED_ON)) ||
+			    ((led_default & E1000_LEDCTL_LED0_IVRT) &&
+			     (mode == E1000_LEDCTL_MODE_LED_OFF))) {
+				ledctl_blink &=
+				    ~(E1000_LEDCTL_LED0_MODE_MASK << i);
+				ledctl_blink |= (E1000_LEDCTL_LED0_BLINK |
+						 E1000_LEDCTL_MODE_LED_ON) << i;
+			}
+		}
+	}
 
 	wr32(E1000_LEDCTL, ledctl_blink);
 

drivers/net/ethernet/intel/igb/e1000_phy.c

@@ -340,6 +340,130 @@ s32 igb_write_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 data)
 	return 0;
 }
 
+/**
+ *  igb_read_sfp_data_byte - Reads SFP module data.
+ *  @hw: pointer to the HW structure
+ *  @offset: byte location offset to be read
+ *  @data: read data buffer pointer
+ *
+ *  Reads one byte from SFP module data stored
+ *  in SFP resided EEPROM memory or SFP diagnostic area.
+ *  Function should be called with
+ *  E1000_I2CCMD_SFP_DATA_ADDR(<byte offset>) for SFP module database access
+ *  E1000_I2CCMD_SFP_DIAG_ADDR(<byte offset>) for SFP diagnostics parameters
+ *  access
+ **/
+s32 igb_read_sfp_data_byte(struct e1000_hw *hw, u16 offset, u8 *data)
+{
+	u32 i = 0;
+	u32 i2ccmd = 0;
+	u32 data_local = 0;
+
+	if (offset > E1000_I2CCMD_SFP_DIAG_ADDR(255)) {
+		hw_dbg("I2CCMD command address exceeds upper limit\n");
+		return -E1000_ERR_PHY;
+	}
+
+	/* Set up Op-code, EEPROM Address,in the I2CCMD
+	 * register. The MAC will take care of interfacing with the
+	 * EEPROM to retrieve the desired data.
+	 */
+	i2ccmd = ((offset << E1000_I2CCMD_REG_ADDR_SHIFT) |
+		  E1000_I2CCMD_OPCODE_READ);
+
+	wr32(E1000_I2CCMD, i2ccmd);
+
+	/* Poll the ready bit to see if the I2C read completed */
+	for (i = 0; i < E1000_I2CCMD_PHY_TIMEOUT; i++) {
+		udelay(50);
+		data_local = rd32(E1000_I2CCMD);
+		if (data_local & E1000_I2CCMD_READY)
+			break;
+	}
+	if (!(data_local & E1000_I2CCMD_READY)) {
+		hw_dbg("I2CCMD Read did not complete\n");
+		return -E1000_ERR_PHY;
+	}
+	if (data_local & E1000_I2CCMD_ERROR) {
+		hw_dbg("I2CCMD Error bit set\n");
+		return -E1000_ERR_PHY;
+	}
+	*data = (u8) data_local & 0xFF;
+
+	return 0;
+}
+
+/**
+ *  e1000_write_sfp_data_byte - Writes SFP module data.
+ *  @hw: pointer to the HW structure
+ *  @offset: byte location offset to write to
+ *  @data: data to write
+ *
+ *  Writes one byte to SFP module data stored
+ *  in SFP resided EEPROM memory or SFP diagnostic area.
+ *  Function should be called with
+ *  E1000_I2CCMD_SFP_DATA_ADDR(<byte offset>) for SFP module database access
+ *  E1000_I2CCMD_SFP_DIAG_ADDR(<byte offset>) for SFP diagnostics parameters
+ *  access
+ **/
+s32 e1000_write_sfp_data_byte(struct e1000_hw *hw, u16 offset, u8 data)
+{
+	u32 i = 0;
+	u32 i2ccmd = 0;
+	u32 data_local = 0;
+
+	if (offset > E1000_I2CCMD_SFP_DIAG_ADDR(255)) {
+		hw_dbg("I2CCMD command address exceeds upper limit\n");
+		return -E1000_ERR_PHY;
+	}
+	/* The programming interface is 16 bits wide
+	 * so we need to read the whole word first
+	 * then update appropriate byte lane and write
+	 * the updated word back.
+	 */
+	/* Set up Op-code, EEPROM Address,in the I2CCMD
+	 * register. The MAC will take care of interfacing
+	 * with an EEPROM to write the data given.
+	 */
+	i2ccmd = ((offset << E1000_I2CCMD_REG_ADDR_SHIFT) |
+		  E1000_I2CCMD_OPCODE_READ);
+	/* Set a command to read single word */
+	wr32(E1000_I2CCMD, i2ccmd);
+	for (i = 0; i < E1000_I2CCMD_PHY_TIMEOUT; i++) {
+		udelay(50);
+		/* Poll the ready bit to see if lastly
+		 * launched I2C operation completed
+		 */
+		i2ccmd = rd32(E1000_I2CCMD);
+		if (i2ccmd & E1000_I2CCMD_READY) {
+			/* Check if this is READ or WRITE phase */
+			if ((i2ccmd & E1000_I2CCMD_OPCODE_READ) ==
+			    E1000_I2CCMD_OPCODE_READ) {
+				/* Write the selected byte
+				 * lane and update whole word
+				 */
+				data_local = i2ccmd & 0xFF00;
+				data_local |= data;
+				i2ccmd = ((offset <<
+					E1000_I2CCMD_REG_ADDR_SHIFT) |
+					E1000_I2CCMD_OPCODE_WRITE | data_local);
+				wr32(E1000_I2CCMD, i2ccmd);
+			} else {
+				break;
+			}
+		}
+	}
+	if (!(i2ccmd & E1000_I2CCMD_READY)) {
+		hw_dbg("I2CCMD Write did not complete\n");
+		return -E1000_ERR_PHY;
+	}
+	if (i2ccmd & E1000_I2CCMD_ERROR) {
+		hw_dbg("I2CCMD Error bit set\n");
+		return -E1000_ERR_PHY;
+	}
+	return 0;
+}
+
 /**
  *  igb_read_phy_reg_igp - Read igp PHY register
  *  @hw: pointer to the HW structure

drivers/net/ethernet/intel/igb/e1000_phy.h

@@ -69,6 +69,8 @@ s32  igb_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data);
 s32  igb_write_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 data);
 s32  igb_read_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 *data);
 s32  igb_write_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 data);
+s32  igb_read_sfp_data_byte(struct e1000_hw *hw, u16 offset, u8 *data);
+s32  e1000_write_sfp_data_byte(struct e1000_hw *hw, u16 offset, u8 data);
 s32  igb_copper_link_setup_82580(struct e1000_hw *hw);
 s32  igb_get_phy_info_82580(struct e1000_hw *hw);
 s32  igb_phy_force_speed_duplex_82580(struct e1000_hw *hw);
@@ -157,4 +159,22 @@ s32  igb_check_polarity_m88(struct e1000_hw *hw);
 #define GS40G_CS_POWER_DOWN		0x0002
 #define GS40G_LINE_LB			0x4000
 
+/* SFP modules ID memory locations */
+#define E1000_SFF_IDENTIFIER_OFFSET	0x00
+#define E1000_SFF_IDENTIFIER_SFF	0x02
+#define E1000_SFF_IDENTIFIER_SFP	0x03
+
+#define E1000_SFF_ETH_FLAGS_OFFSET	0x06
+/* Flags for SFP modules compatible with ETH up to 1Gb */
+struct e1000_sfp_flags {
+	u8 e1000_base_sx:1;
+	u8 e1000_base_lx:1;
+	u8 e1000_base_cx:1;
+	u8 e1000_base_t:1;
+	u8 e100_base_lx:1;
+	u8 e100_base_fx:1;
+	u8 e10_base_bx10:1;
+	u8 e10_base_px:1;
+};
+
 #endif

drivers/net/ethernet/intel/igb/igb.h

@@ -322,11 +322,6 @@ static inline int igb_desc_unused(struct igb_ring *ring)
 	return ring->count + ring->next_to_clean - ring->next_to_use - 1;
 }
 
-struct igb_i2c_client_list {
-	struct i2c_client *client;
-	struct igb_i2c_client_list *next;
-};
-
 #ifdef CONFIG_IGB_HWMON
 
 #define IGB_HWMON_TYPE_LOC	0
@@ -514,13 +509,18 @@ extern void igb_ptp_rx_rgtstamp(struct igb_q_vector *q_vector,
 extern void igb_ptp_rx_pktstamp(struct igb_q_vector *q_vector,
 				unsigned char *va,
 				struct sk_buff *skb);
-static inline void igb_ptp_rx_hwtstamp(struct igb_q_vector *q_vector,
+static inline void igb_ptp_rx_hwtstamp(struct igb_ring *rx_ring,
 				       union e1000_adv_rx_desc *rx_desc,
 				       struct sk_buff *skb)
 {
 	if (igb_test_staterr(rx_desc, E1000_RXDADV_STAT_TS) &&
 	    !igb_test_staterr(rx_desc, E1000_RXDADV_STAT_TSIP))
-		igb_ptp_rx_rgtstamp(q_vector, skb);
+		igb_ptp_rx_rgtstamp(rx_ring->q_vector, skb);
+
+	/* Update the last_rx_timestamp timer in order to enable watchdog check
+	 * for error case of latched timestamp on a dropped packet.
+	 */
+	rx_ring->last_rx_timestamp = jiffies;
 }
 
 extern int igb_ptp_hwtstamp_ioctl(struct net_device *netdev,

drivers/net/ethernet/intel/igb/igb_ethtool.c

@@ -142,6 +142,8 @@ static int igb_get_settings(struct net_device *netdev, struct ethtool_cmd *ecmd)
 {
 	struct igb_adapter *adapter = netdev_priv(netdev);
 	struct e1000_hw *hw = &adapter->hw;
+	struct e1000_dev_spec_82575 *dev_spec = &hw->dev_spec._82575;
+	struct e1000_sfp_flags *eth_flags = &dev_spec->eth_flags;
 	u32 status;
 
 	if (hw->phy.media_type == e1000_media_type_copper) {
@@ -162,49 +164,26 @@ static int igb_get_settings(struct net_device *netdev, struct ethtool_cmd *ecmd)
 			ecmd->advertising |= hw->phy.autoneg_advertised;
 		}
 
-		if (hw->mac.autoneg != 1)
-			ecmd->advertising &= ~(ADVERTISED_Pause |
-					       ADVERTISED_Asym_Pause);
-
-		if (hw->fc.requested_mode == e1000_fc_full)
-			ecmd->advertising |= ADVERTISED_Pause;
-		else if (hw->fc.requested_mode == e1000_fc_rx_pause)
-			ecmd->advertising |= (ADVERTISED_Pause |
-					      ADVERTISED_Asym_Pause);
-		else if (hw->fc.requested_mode == e1000_fc_tx_pause)
-			ecmd->advertising |=  ADVERTISED_Asym_Pause;
-		else
-			ecmd->advertising &= ~(ADVERTISED_Pause |
-					       ADVERTISED_Asym_Pause);
-
 		ecmd->port = PORT_TP;
 		ecmd->phy_address = hw->phy.addr;
 		ecmd->transceiver = XCVR_INTERNAL;
 	} else {
-		ecmd->supported = (SUPPORTED_1000baseT_Full |
-				   SUPPORTED_100baseT_Full |
-				   SUPPORTED_FIBRE |
+		ecmd->supported = (SUPPORTED_FIBRE |
 				   SUPPORTED_Autoneg |
 				   SUPPORTED_Pause);
-		if (hw->mac.type == e1000_i354)
-				ecmd->supported |= SUPPORTED_2500baseX_Full;
-
 		ecmd->advertising = ADVERTISED_FIBRE;
-
-		switch (adapter->link_speed) {
-		case SPEED_2500:
-			ecmd->advertising = ADVERTISED_2500baseX_Full;
-			break;
-		case SPEED_1000:
-			ecmd->advertising = ADVERTISED_1000baseT_Full;
-			break;
-		case SPEED_100:
-			ecmd->advertising = ADVERTISED_100baseT_Full;
-			break;
-		default:
-			break;
+		if (hw->mac.type == e1000_i354) {
+			ecmd->supported |= SUPPORTED_2500baseX_Full;
+			ecmd->advertising |= ADVERTISED_2500baseX_Full;
+		}
+		if ((eth_flags->e1000_base_lx) || (eth_flags->e1000_base_sx)) {
+			ecmd->supported |= SUPPORTED_1000baseT_Full;
+			ecmd->advertising |= ADVERTISED_1000baseT_Full;
+		}
+		if (eth_flags->e100_base_fx) {
+			ecmd->supported |= SUPPORTED_100baseT_Full;
+			ecmd->advertising |= ADVERTISED_100baseT_Full;
 		}
-
 		if (hw->mac.autoneg == 1)
 			ecmd->advertising |= ADVERTISED_Autoneg;
 
@@ -212,6 +191,21 @@ static int igb_get_settings(struct net_device *netdev, struct ethtool_cmd *ecmd)
 		ecmd->transceiver = XCVR_EXTERNAL;
 	}
 
+	if (hw->mac.autoneg != 1)
+		ecmd->advertising &= ~(ADVERTISED_Pause |
+				       ADVERTISED_Asym_Pause);
+
+	if (hw->fc.requested_mode == e1000_fc_full)
+		ecmd->advertising |= ADVERTISED_Pause;
+	else if (hw->fc.requested_mode == e1000_fc_rx_pause)
+		ecmd->advertising |= (ADVERTISED_Pause |
+				      ADVERTISED_Asym_Pause);
+	else if (hw->fc.requested_mode == e1000_fc_tx_pause)
+		ecmd->advertising |=  ADVERTISED_Asym_Pause;
+	else
+		ecmd->advertising &= ~(ADVERTISED_Pause |
+				       ADVERTISED_Asym_Pause);
+
 	status = rd32(E1000_STATUS);
 
 	if (status & E1000_STATUS_LU) {
@@ -392,6 +386,10 @@ static int igb_set_pauseparam(struct net_device *netdev,
 	struct e1000_hw *hw = &adapter->hw;
 	int retval = 0;
 
+	/* 100basefx does not support setting link flow control */
+	if (hw->dev_spec._82575.eth_flags.e100_base_fx)
+		return -EINVAL;
+
 	adapter->fc_autoneg = pause->autoneg;
 
 	while (test_and_set_bit(__IGB_RESETTING, &adapter->state))
@@ -813,10 +811,8 @@ static int igb_set_eeprom(struct net_device *netdev,
 	ret_val = hw->nvm.ops.write(hw, first_word,
 				    last_word - first_word + 1, eeprom_buff);
 
-	/* Update the checksum over the first part of the EEPROM if needed
-	 * and flush shadow RAM for 82573 controllers
-	 */
-	if ((ret_val == 0) && ((first_word <= NVM_CHECKSUM_REG)))
+	/* Update the checksum if nvm write succeeded */
+	if (ret_val == 0)
 		hw->nvm.ops.update(hw);
 
 	igb_set_fw_version(adapter);

drivers/net/ethernet/intel/igb/igb_main.c

@@ -1667,10 +1667,13 @@ void igb_down(struct igb_adapter *adapter)
 	wrfl();
 	msleep(10);
 
-	for (i = 0; i < adapter->num_q_vectors; i++)
+	igb_irq_disable(adapter);
+
+	for (i = 0; i < adapter->num_q_vectors; i++) {
+		napi_synchronize(&(adapter->q_vector[i]->napi));
 		napi_disable(&(adapter->q_vector[i]->napi));
+	}
 
-	igb_irq_disable(adapter);
 
 	del_timer_sync(&adapter->watchdog_timer);
 	del_timer_sync(&adapter->phy_info_timer);
@@ -6622,7 +6625,7 @@ static void igb_process_skb_fields(struct igb_ring *rx_ring,
 
 	igb_rx_checksum(rx_ring, rx_desc, skb);
 
-	igb_ptp_rx_hwtstamp(rx_ring->q_vector, rx_desc, skb);
+	igb_ptp_rx_hwtstamp(rx_ring, rx_desc, skb);
 
 	if ((dev->features & NETIF_F_HW_VLAN_CTAG_RX) &&
 	    igb_test_staterr(rx_desc, E1000_RXD_STAT_VP)) {

drivers/net/ethernet/intel/ixgbe/ixgbe_dcb.c

@@ -380,3 +380,26 @@ s32 ixgbe_dcb_hw_ets_config(struct ixgbe_hw *hw,
 	}
 	return 0;
 }
+
+static void ixgbe_dcb_read_rtrup2tc_82599(struct ixgbe_hw *hw, u8 *map)
+{
+	u32 reg, i;
+
+	reg = IXGBE_READ_REG(hw, IXGBE_RTRUP2TC);
+	for (i = 0; i < MAX_USER_PRIORITY; i++)
+		map[i] = IXGBE_RTRUP2TC_UP_MASK &
+			(reg >> (i * IXGBE_RTRUP2TC_UP_SHIFT));
+	return;
+}
+
+void ixgbe_dcb_read_rtrup2tc(struct ixgbe_hw *hw, u8 *map)
+{
+	switch (hw->mac.type) {
+	case ixgbe_mac_82599EB:
+	case ixgbe_mac_X540:
+		ixgbe_dcb_read_rtrup2tc_82599(hw, map);
+		break;
+	default:
+		break;
+	}
+}

drivers/net/ethernet/intel/ixgbe/ixgbe_dcb.h

@@ -159,6 +159,8 @@ s32 ixgbe_dcb_hw_ets_config(struct ixgbe_hw *hw, u16 *refill, u16 *max,
 s32 ixgbe_dcb_hw_pfc_config(struct ixgbe_hw *hw, u8 pfc_en, u8 *tc_prio);
 s32 ixgbe_dcb_hw_config(struct ixgbe_hw *, struct ixgbe_dcb_config *);
 
+void ixgbe_dcb_read_rtrup2tc(struct ixgbe_hw *hw, u8 *map);
+
 /* DCB definitions for credit calculation */
 #define DCB_CREDIT_QUANTUM	64   /* DCB Quantum */
 #define MAX_CREDIT_REFILL       511  /* 0x1FF * 64B = 32704B */

drivers/net/ethernet/intel/ixgbe/ixgbe_dcb_82599.h

@@ -45,6 +45,7 @@
 
 /* Receive UP2TC mapping */
 #define IXGBE_RTRUP2TC_UP_SHIFT 3
+#define IXGBE_RTRUP2TC_UP_MASK	7
 /* Transmit UP2TC mapping */
 #define IXGBE_RTTUP2TC_UP_SHIFT 3
 

drivers/net/ethernet/intel/ixgbe/ixgbe_dcb_nl.c

@@ -554,6 +554,9 @@ static int ixgbe_dcbnl_ieee_setets(struct net_device *dev,
 		for (i = 0; i < IEEE_8021QAZ_MAX_TCS; i++)
 			adapter->ixgbe_ieee_ets->prio_tc[i] =
 				IEEE_8021QAZ_MAX_TCS;
+		/* if possible update UP2TC mappings from HW */
+		ixgbe_dcb_read_rtrup2tc(&adapter->hw,
+					adapter->ixgbe_ieee_ets->prio_tc);
 	}
 
 	for (i = 0; i < IEEE_8021QAZ_MAX_TCS; i++) {