Commit 3528dd34 authored by Arun Kumar K's avatar Arun Kumar K Committed by Kukjin Kim

ARM: dts: Add exynos5420 peach-pit board support

Adds the google peach-pit board dts file which uses
exynos5420 SoC.
Signed-off-by: default avatarArun Kumar K <arun.kk@samsung.com>
Signed-off-by: default avatarDoug Anderson <dianders@chromium.org>
Reviewed-by: default avatarDoug Anderson <dianders@chromium.org>
Signed-off-by: default avatarKukjin Kim <kgene.kim@samsung.com>
parent 8e371a91
...@@ -74,6 +74,7 @@ dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \ ...@@ -74,6 +74,7 @@ dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \
exynos5250-smdk5250.dtb \ exynos5250-smdk5250.dtb \
exynos5250-snow.dtb \ exynos5250-snow.dtb \
exynos5420-arndale-octa.dtb \ exynos5420-arndale-octa.dtb \
exynos5420-peach-pit.dtb \
exynos5420-smdk5420.dtb \ exynos5420-smdk5420.dtb \
exynos5440-sd5v1.dtb \ exynos5440-sd5v1.dtb \
exynos5440-ssdk5440.dtb exynos5440-ssdk5440.dtb
......
/*
* Google Peach Pit Rev 6+ board device tree source
*
* Copyright (c) 2014 Google, Inc
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
/dts-v1/;
#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/gpio.h>
#include "exynos5420.dtsi"
/ {
model = "Google Peach Pit Rev 6+";
compatible = "google,pit-rev16",
"google,pit-rev15", "google,pit-rev14",
"google,pit-rev13", "google,pit-rev12",
"google,pit-rev11", "google,pit-rev10",
"google,pit-rev9", "google,pit-rev8",
"google,pit-rev7", "google,pit-rev6",
"google,pit", "google,peach","samsung,exynos5420",
"samsung,exynos5";
memory {
reg = <0x20000000 0x80000000>;
};
fixed-rate-clocks {
oscclk {
compatible = "samsung,exynos5420-oscclk";
clock-frequency = <24000000>;
};
};
gpio-keys {
compatible = "gpio-keys";
pinctrl-names = "default";
pinctrl-0 = <&power_key_irq>;
power {
label = "Power";
gpios = <&gpx1 2 GPIO_ACTIVE_LOW>;
linux,code = <KEY_POWER>;
gpio-key,wakeup;
};
};
backlight {
compatible = "pwm-backlight";
pwms = <&pwm 0 1000000 0>;
brightness-levels = <0 100 500 1000 1500 2000 2500 2800>;
default-brightness-level = <7>;
pinctrl-0 = <&pwm0_out>;
pinctrl-names = "default";
};
};
&pinctrl_0 {
tpm_irq: tpm-irq {
samsung,pins = "gpx1-0";
samsung,pin-function = <0>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
power_key_irq: power-key-irq {
samsung,pins = "gpx1-2";
samsung,pin-function = <0>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
};
&rtc {
status = "okay";
};
&uart_3 {
status = "okay";
};
&mmc_0 {
status = "okay";
num-slots = <1>;
broken-cd;
caps2-mmc-hs200-1_8v;
supports-highspeed;
non-removable;
card-detect-delay = <200>;
clock-frequency = <400000000>;
samsung,dw-mshc-ciu-div = <3>;
samsung,dw-mshc-sdr-timing = <0 4>;
samsung,dw-mshc-ddr-timing = <0 2>;
pinctrl-names = "default";
pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>;
slot@0 {
reg = <0>;
bus-width = <8>;
};
};
&mmc_2 {
status = "okay";
num-slots = <1>;
supports-highspeed;
card-detect-delay = <200>;
clock-frequency = <400000000>;
samsung,dw-mshc-ciu-div = <3>;
samsung,dw-mshc-sdr-timing = <2 3>;
samsung,dw-mshc-ddr-timing = <1 2>;
pinctrl-names = "default";
pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
slot@0 {
reg = <0>;
bus-width = <4>;
};
};
&hsi2c_9 {
status = "okay";
clock-frequency = <400000>;
tpm@20 {
compatible = "infineon,slb9645tt";
reg = <0x20>;
/* Unused irq; but still need to configure the pins */
pinctrl-names = "default";
pinctrl-0 = <&tpm_irq>;
};
};
/*
* Use longest HW watchdog in SoC (32 seconds) since the hardware
* watchdog provides no debugging information (compared to soft/hard
* lockup detectors) and so should be last resort.
*/
&watchdog {
timeout-sec = <32>;
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment