Commit 35d35aae authored by Tushar Behera's avatar Tushar Behera Committed by Nicolas Ferre

dt-bindings: clock: Move at91.h to dt-bindigs/clock

Most of the clock related dt-binding header files are located in
dt-bindings/clock folder. It would be good to keep all the similar
header files at a single location.
Signed-off-by: default avatarTushar Behera <tushar.behera@linaro.org>
CC: Rob Landley <rob@landley.net>
CC: Andrew Victor <linux@maxim.org.za>
CC: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Acked-by: default avatarBoris BREZILLON <b.brezillon.dev@gmail.com>
[nicolas.ferre@atmel.com: add new at91sam9261 & at91sam9rl]
Signed-off-by: default avatarNicolas Ferre <nicolas.ferre@atmel.com>
parent d44db494
...@@ -62,7 +62,7 @@ Required properties for PMC node: ...@@ -62,7 +62,7 @@ Required properties for PMC node:
- interrupt-controller : tell that the PMC is an interrupt controller. - interrupt-controller : tell that the PMC is an interrupt controller.
- #interrupt-cells : must be set to 1. The first cell encodes the interrupt id, - #interrupt-cells : must be set to 1. The first cell encodes the interrupt id,
and reflect the bit position in the PMC_ER/DR/SR registers. and reflect the bit position in the PMC_ER/DR/SR registers.
You can use the dt macros defined in dt-bindings/clk/at91.h. You can use the dt macros defined in dt-bindings/clock/at91.h.
0 (AT91_PMC_MOSCS) -> main oscillator ready 0 (AT91_PMC_MOSCS) -> main oscillator ready
1 (AT91_PMC_LOCKA) -> PLL A ready 1 (AT91_PMC_LOCKA) -> PLL A ready
2 (AT91_PMC_LOCKB) -> PLL B ready 2 (AT91_PMC_LOCKB) -> PLL B ready
......
...@@ -10,7 +10,7 @@ ...@@ -10,7 +10,7 @@
#include <dt-bindings/pinctrl/at91.h> #include <dt-bindings/pinctrl/at91.h>
#include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h> #include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/clk/at91.h> #include <dt-bindings/clock/at91.h>
/ { / {
model = "Atmel AT91SAM9261 family SoC"; model = "Atmel AT91SAM9261 family SoC";
......
...@@ -8,7 +8,7 @@ ...@@ -8,7 +8,7 @@
#include "skeleton.dtsi" #include "skeleton.dtsi"
#include <dt-bindings/pinctrl/at91.h> #include <dt-bindings/pinctrl/at91.h>
#include <dt-bindings/clk/at91.h> #include <dt-bindings/clock/at91.h>
#include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h> #include <dt-bindings/gpio/gpio.h>
......
...@@ -13,7 +13,7 @@ ...@@ -13,7 +13,7 @@
#include <dt-bindings/pinctrl/at91.h> #include <dt-bindings/pinctrl/at91.h>
#include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h> #include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/clk/at91.h> #include <dt-bindings/clock/at91.h>
/ { / {
model = "Atmel SAMA5D3 family SoC"; model = "Atmel SAMA5D3 family SoC";
......
...@@ -9,7 +9,7 @@ ...@@ -9,7 +9,7 @@
#include <dt-bindings/pinctrl/at91.h> #include <dt-bindings/pinctrl/at91.h>
#include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/clk/at91.h> #include <dt-bindings/clock/at91.h>
/ { / {
ahb { ahb {
......
...@@ -9,7 +9,7 @@ ...@@ -9,7 +9,7 @@
#include <dt-bindings/pinctrl/at91.h> #include <dt-bindings/pinctrl/at91.h>
#include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/clk/at91.h> #include <dt-bindings/clock/at91.h>
/ { / {
aliases { aliases {
......
...@@ -9,7 +9,7 @@ ...@@ -9,7 +9,7 @@
#include <dt-bindings/pinctrl/at91.h> #include <dt-bindings/pinctrl/at91.h>
#include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/clk/at91.h> #include <dt-bindings/clock/at91.h>
/ { / {
aliases { aliases {
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment