be2net: avoid disabling sriov while VFs are assigned

Calling pci_disable_sriov() while VFs are assigned to VMs causes
kernel panic. This patch uses PCI_DEV_FLAGS_ASSIGNED bit state of the
VF's pci_dev to avoid this. Also, the unconditional function reset cmd
issued on a PF probe can delete the VF configuration for the
previously enabled VFs. A scratchpad register is now used to issue a
function reset only when needed (i.e., in a crash dump scenario.)
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/emulex/benet/be.h

@@ -313,6 +313,11 @@ struct be_vf_cfg {
 	u32 tx_rate;
 };
 
+enum vf_state {
+	ENABLED = 0,
+	ASSIGNED = 1
+};
+
 #define BE_FLAGS_LINK_STATUS_INIT		1
 #define BE_FLAGS_WORKER_SCHEDULED		(1 << 3)
 #define BE_UC_PMAC_COUNT		30
@@ -403,8 +408,9 @@ struct be_adapter {
 	u32 flash_status;
 	struct completion flash_compl;
 
-	u32 num_vfs;
-	u8 is_virtfn;
+	u32 num_vfs;		/* Number of VFs provisioned by PF driver */
+	u32 dev_num_vfs;	/* Number of VFs supported by HW */
+	u8 virtfn;
 	struct be_vf_cfg *vf_cfg;
 	bool be3_native;
 	u32 sli_family;
@@ -417,8 +423,10 @@ struct be_adapter {
 	u32 uc_macs;		/* Count of secondary UC MAC programmed */
 };
 
-#define be_physfn(adapter) (!adapter->is_virtfn)
+#define be_physfn(adapter)		(!adapter->virtfn)
 #define	sriov_enabled(adapter)		(adapter->num_vfs > 0)
+#define	sriov_want(adapter)		(adapter->dev_num_vfs && num_vfs && \
+					 be_physfn(adapter))
 #define for_all_vfs(adapter, vf_cfg, i)					\
 	for (i = 0, vf_cfg = &adapter->vf_cfg[i]; i < adapter->num_vfs;	\
 		i++, vf_cfg++)
@@ -547,14 +555,6 @@ static inline u8 is_udp_pkt(struct sk_buff *skb)
 	return val;
 }
 
-static inline void be_check_sriov_fn_type(struct be_adapter *adapter)
-{
-	u32 sli_intf;
-
-	pci_read_config_dword(adapter->pdev, SLI_INTF_REG_OFFSET, &sli_intf);
-	adapter->is_virtfn = (sli_intf & SLI_INTF_FT_MASK) ? 1 : 0;
-}
-
 static inline void be_vf_eth_addr_generate(struct be_adapter *adapter, u8 *mac)
 {
 	u32 addr;

drivers/net/ethernet/emulex/benet/be_hw.h

@@ -58,6 +58,8 @@
 
 #define SLI_PORT_CONTROL_IP_MASK	0x08000000
 
+#define PCICFG_CUST_SCRATCHPAD_CSR	0x1EC
+
 /********* Memory BAR register ************/
 #define PCICFG_MEMBAR_CTRL_INT_CTRL_OFFSET 	0xfc
 /* Host Interrupt Enable, if set interrupts are enabled although "PCI Interrupt