Commit 3af50481 authored by Bruce Allan's avatar Bruce Allan Committed by David S. Miller

e1000e: cleanup ethtool loopback setup code

Refactor the loopback setup code to first handle the only 10/100 PHY
supported by the driver if applicable and then handle the 1Gig PHYs in a
switch statement for PHY-specific setups.
Signed-off-by: default avatarBruce Allan <bruce.w.allan@intel.com>
Tested-by: default avatarEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: default avatarJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 20c0da65
......@@ -1263,33 +1263,36 @@ static int e1000_integrated_phy_loopback(struct e1000_adapter *adapter)
hw->mac.autoneg = 0;
/* Workaround: K1 must be disabled for stable 1Gbps operation */
if (hw->mac.type == e1000_pchlan)
e1000_configure_k1_ich8lan(hw, false);
if (hw->phy.type == e1000_phy_m88) {
/* Auto-MDI/MDIX Off */
e1e_wphy(hw, M88E1000_PHY_SPEC_CTRL, 0x0808);
/* reset to update Auto-MDI/MDIX */
e1e_wphy(hw, PHY_CONTROL, 0x9140);
/* autoneg off */
e1e_wphy(hw, PHY_CONTROL, 0x8140);
} else if (hw->phy.type == e1000_phy_gg82563)
e1e_wphy(hw, GG82563_PHY_KMRN_MODE_CTRL, 0x1CC);
ctrl_reg = er32(CTRL);
switch (hw->phy.type) {
case e1000_phy_ife:
if (hw->phy.type == e1000_phy_ife) {
/* force 100, set loopback */
e1e_wphy(hw, PHY_CONTROL, 0x6100);
/* Now set up the MAC to the same speed/duplex as the PHY. */
ctrl_reg = er32(CTRL);
ctrl_reg &= ~E1000_CTRL_SPD_SEL; /* Clear the speed sel bits */
ctrl_reg |= (E1000_CTRL_FRCSPD | /* Set the Force Speed Bit */
E1000_CTRL_FRCDPX | /* Set the Force Duplex Bit */
E1000_CTRL_SPD_100 |/* Force Speed to 100 */
E1000_CTRL_FD); /* Force Duplex to FULL */
ew32(CTRL, ctrl_reg);
udelay(500);
return 0;
}
/* Specific PHY configuration for loopback */
switch (hw->phy.type) {
case e1000_phy_m88:
/* Auto-MDI/MDIX Off */
e1e_wphy(hw, M88E1000_PHY_SPEC_CTRL, 0x0808);
/* reset to update Auto-MDI/MDIX */
e1e_wphy(hw, PHY_CONTROL, 0x9140);
/* autoneg off */
e1e_wphy(hw, PHY_CONTROL, 0x8140);
break;
case e1000_phy_gg82563:
e1e_wphy(hw, GG82563_PHY_KMRN_MODE_CTRL, 0x1CC);
break;
case e1000_phy_bm:
/* Set Default MAC Interface speed to 1GB */
......@@ -1312,23 +1315,30 @@ static int e1000_integrated_phy_loopback(struct e1000_adapter *adapter)
/* Set Early Link Enable */
e1e_rphy(hw, PHY_REG(769, 20), &phy_reg);
e1e_wphy(hw, PHY_REG(769, 20), phy_reg | 0x0400);
/* fall through */
break;
case e1000_phy_82577:
case e1000_phy_82578:
/* Workaround: K1 must be disabled for stable 1Gbps operation */
e1000_configure_k1_ich8lan(hw, false);
break;
default:
/* force 1000, set loopback */
e1e_wphy(hw, PHY_CONTROL, 0x4140);
mdelay(250);
break;
}
/* Now set up the MAC to the same speed/duplex as the PHY. */
ctrl_reg = er32(CTRL);
ctrl_reg &= ~E1000_CTRL_SPD_SEL; /* Clear the speed sel bits */
ctrl_reg |= (E1000_CTRL_FRCSPD | /* Set the Force Speed Bit */
E1000_CTRL_FRCDPX | /* Set the Force Duplex Bit */
E1000_CTRL_SPD_1000 |/* Force Speed to 1000 */
E1000_CTRL_FD); /* Force Duplex to FULL */
/* force 1000, set loopback */
e1e_wphy(hw, PHY_CONTROL, 0x4140);
mdelay(250);
if (adapter->flags & FLAG_IS_ICH)
ctrl_reg |= E1000_CTRL_SLU; /* Set Link Up */
}
/* Now set up the MAC to the same speed/duplex as the PHY. */
ctrl_reg = er32(CTRL);
ctrl_reg &= ~E1000_CTRL_SPD_SEL; /* Clear the speed sel bits */
ctrl_reg |= (E1000_CTRL_FRCSPD | /* Set the Force Speed Bit */
E1000_CTRL_FRCDPX | /* Set the Force Duplex Bit */
E1000_CTRL_SPD_1000 |/* Force Speed to 1000 */
E1000_CTRL_FD); /* Force Duplex to FULL */
if (adapter->flags & FLAG_IS_ICH)
ctrl_reg |= E1000_CTRL_SLU; /* Set Link Up */
if (hw->phy.media_type == e1000_media_type_copper &&
hw->phy.type == e1000_phy_m88) {
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment