ARM: dts: at91: sama5d2: Move flx3 definitions in the SoC dtsi

The Flexcom IP is part of the sama5d2 SoC. Move the flx3 node together
with its function definitions in sama5d2.dtsi. Boards will just fill
the pins and enable the desired functions.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-4-tudor.ambarus@microchip.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>

arch/arm/boot/dts/at91-kizbox3_common.dtsi

@@ -325,21 +325,8 @@ &flx3 {
 	status = "disabled";
 
 	uart8: serial@200 {
-		compatible = "atmel,at91sam9260-usart";
-		reg = <0x200 0x400>;
-		interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>;
-		dmas = <&dma0
-			(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
-			| AT91_XDMAC_DT_PERID(17))>,
-		       <&dma0
-			(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
-			| AT91_XDMAC_DT_PERID(18))>;
-		dma-names = "tx", "rx";
-		clocks = <&pmc PMC_TYPE_PERIPHERAL 22>;
-		clock-names = "usart";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_flx3_default>;
-		atmel,fifo-size = <32>;
 		atmel,use-dma-rx;
 		atmel,use-dma-tx;
 		status = "disabled";

arch/arm/boot/dts/at91-sama5d27_som1_ek.dts

@@ -179,26 +179,15 @@ flx3: flexcom@fc014000 {
 				status = "disabled";
 
 				uart8: serial@200 {
-					compatible = "atmel,at91sam9260-usart";
-					reg = <0x200 0x200>;
-					interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>;
-					clocks = <&pmc PMC_TYPE_PERIPHERAL 22>;
-					clock-names = "usart";
+					dmas = <0>, <0>;
 					pinctrl-names = "default";
 					pinctrl-0 = <&pinctrl_flx3_default>;
-					atmel,fifo-size = <32>;
 					status = "disabled"; /* Conflict with isc. */
 				};
 
 				spi5: spi@400 {
-					compatible = "atmel,at91rm9200-spi";
-					reg = <0x400 0x200>;
-					interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>;
-					clocks = <&pmc PMC_TYPE_PERIPHERAL 22>;
-					clock-names = "spi_clk";
 					pinctrl-names = "default";
 					pinctrl-0 = <&pinctrl_flx3_default>;
-					atmel,fifo-size = <16>;
 					status = "disabled"; /* Conflict with isc. */
 				};
 			};

arch/arm/boot/dts/at91-sama5d2_icp.dts

@@ -185,14 +185,8 @@ &flx3 { /* mikrobus1 spi */
 	status = "okay";
 
 	spi5: spi@400 {
-		compatible = "atmel,at91rm9200-spi";
-		reg = <0x400 0x200>;
-		interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>;
-		clocks = <&pmc PMC_TYPE_PERIPHERAL 22>;
-		clock-names = "spi_clk";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_mikrobus1_spi &pinctrl_mikrobus1_spi_cs>;
-		atmel,fifo-size = <16>;
 		status = "okay";
 	};
 };

arch/arm/boot/dts/sama5d2.dtsi

@@ -804,6 +804,35 @@ flx3: flexcom@fc014000 {
 				#size-cells = <1>;
 				ranges = <0x0 0xfc014000 0x800>;
 				status = "disabled";
+
+				uart8: serial@200 {
+					compatible = "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 22>;
+					clock-names = "usart";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(17))>,
+					       <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(18))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <32>;
+					status = "disabled";
+				};
+
+				spi5: spi@400 {
+					compatible = "atmel,at91rm9200-spi";
+					reg = <0x400 0x200>;
+					interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 22>;
+					clock-names = "spi_clk";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
 			};
 
 			flx4: flexcom@fc018000 {